1. uart_wait_tx_done works incorrect when sending a byte of data.
2. uart_set_rx_timeout sets an incorrect rx timeout value when ref_tick is enabled
closes https://github.com/espressif/esp-idf/issues/3631
There are lot of prints of `Allocate TX buffer for DMA`
Changed these from `ESP_LOGI` to `ESP_LOGD`
Signed-off-by: Vikram Dattu <vikram.dattu@espressif.com>
Do not include bootloader in flash target when secure boot is enabled.
Emit signing warning on all cases where signed apps are enabled (secure
boot and signed images)
Follow convention of capital letters for SECURE_BOOT_SIGNING_KEY
variable, since it is
relevant to other components, not just bootloader.
Pass signing key and verification key via config, not requiring
bootloader to know parent app dir.
Misc. variables name corrections
Using xxx_periph.h in whole IDF instead of xxx_reg.h, xxx_struct.h, xxx_channel.h ... .
Cleaned up header files from unnecessary headers (releated to soc/... headers).
Description for i2c_slave_read_buffer had leftover from copying from write fct. data
pointer description described the wrong way (writing into internal buffer)
Closes https://github.com/espressif/esp-idf/pull/3268
introduced in f871cc5ffa
The issue is caused by
1. The hal didn't pass the io_mode to LL.
2. The setup_device function overwrite the trans-specific settings.
This MR removes the common dependency from every IDF components to the SOC component.
Currently, in the ``idf_functions.cmake`` script, we include the header path of SOC component by default for all components.
But for better code organization (or maybe also benifits to the compiling speed), we may remove the dependency to SOC components for most components except the driver and kernel related components.
In CMAKE, we have two kinds of header visibilities (set by include path visibility):
(Assume component A --(depends on)--> B, B is the current component)
1. public (``COMPONENT_ADD_INCLUDEDIRS``): means this path is visible to other depending components (A) (visible to A and B)
2. private (``COMPONENT_PRIV_INCLUDEDIRS``): means this path is only visible to source files inside the component (visible to B only)
and we have two kinds of depending ways:
(Assume component A --(depends on)--> B --(depends on)--> C, B is the current component)
1. public (```COMPONENT_REQUIRES```): means B can access to public include path of C. All other components rely on you (A) will also be available for the public headers. (visible to A, B)
2. private (``COMPONENT_PRIV_REQUIRES``): means B can access to public include path of C, but don't propagate this relation to other components (A). (visible to B)
1. remove the common requirement in ``idf_functions.cmake``, this makes the SOC components invisible to all other components by default.
2. if a component (for example, DRIVER) really needs the dependency to SOC, add a private dependency to SOC for it.
3. some other components that don't really depends on the SOC may still meet some errors saying "can't find header soc/...", this is because it's depended component (DRIVER) incorrectly include the header of SOC in its public headers. Moving all this kind of #include into source files, or private headers
4. Fix the include requirements for some file which miss sufficient #include directives. (Previously they include some headers by the long long long header include link)
This is a breaking change. Previous code may depends on the long include chain.
You may need to include the following headers for some files after this commit:
- soc/soc.h
- soc/soc_memory_layout.h
- driver/gpio.h
- esp_sleep.h
The major broken include chain includes:
1. esp_system.h no longer includes esp_sleep.h. The latter includes driver/gpio.h and driver/touch_pad.h.
2. ets_sys.h no longer includes soc/soc.h
3. freertos/portmacro.h no longer includes soc/soc_memory_layout.h
some peripheral headers no longer includes their hw related headers, e.g. rom/gpio.h no longer includes soc/gpio_pins.h and soc/gpio_reg.h
BREAKING CHANGE
stdatomic.h is available both in newlib and GCC include directories.
Normally (if you invoke the compiler without any flags) GCC include
directories are first on the list, so GCC’s stdatomic.h is used. In
IDF, we used to pass newlib include path as an extra include
directory, so newlib’s stdint.h got included instead.
Newlib 2.2.0 stdatomic implementation is compatible with -std=gnu99
but incompatible with -std=gnu11. And GCC doesn’t support atomic_load
with -std=gnu99 (it’s a C11 feature). So when we used atomic_load
with -std=gnu99, it worked due to newlib’s header.
Since we are no longer going to be including newlib headers into IDF,
GCC stdatomic will be used instead. Hence, add -std=gnu11 for source
files which use atomic features.
1. separate rom include files and linkscript to esp_rom
2. modefiy "include rom/xxx.h" to "include esp32/rom/xxx.h"
3. Forward compatible
4. update mqtt
GCC compiler can generate 8-bit stores when modifying bitfields of
volatile structs (https://github.com/espressif/esp-idf/issues/597).
In the specific case of I2C driver, this resulted in byte_num field
to be written using s8i. However the peripheral requires 32-bit
writes, and ignores 8-bit writes. This change modifies the code to
compose the 32-bit command register value first, and then write the
complete value to the hardware.
Acquires PM_APB_FREQ_MAX lock when carrying any transaction on I2S if
Power Management Framework is enabled.
Signed-off-by: Sachin Parekh <sachin.parekh@espressif.com>
Acquires PM_APB_FREQ_MAX lock when carrying any transaction on I2C if
Power Management Framework is enabled.
Signed-off-by: Sachin Parekh <sachin.parekh@espressif.com>
Removed as much branching (if statements) from the
gpio_intr_service ISR, as possible and split the while loop into
two. Also forced writing the two status*_w1tc variables only once,
instead of every time after calling the external function hooks.
The measurements below, was done using the following tools:
Toolchain version: crosstool-ng-1.22.0-80-g6c4433a
Compiler version: 5.2.0
Here follows a comparison of the gpio_intr_service ISR's
execution time, using a DS1054 oscilloscope. All the time spent
calling external functions, via the function pointers
gpio_isr_func[gpio_num].fn, were disregarded.
With OPTIMIZATION_FLAGS = -Og, 1.34 uSeconds faster:
3.22 uSec (with this patch)
4.56 uSec (with commit 71c90ac4)
100 - (100 * 4.56 / 3.22) = 42% faster
With OPTIMIZATION_FLAGS = -Os, 1.65 uSeconds faster:
2.89 uSec (with this patch)
4.54 uSec (with commit 71c90ac4)
100 - (100 * 4.54 / 2.89) = 57% faster
Signed-off-by: Konstantin Kondrashov <konstantin@espressif.com>
Merges https://github.com/espressif/esp-idf/pull/2861
This commits adds the functions can_clear_transmit_queue() and
can_clear_receive_queue(). Closes#2906
The following bug are fixed:
- CAN_IO_UNUSED is now explicitly cast to enum type. Closes#2825
- Fix multiple documentation errors. Closes#2898, Closes#2794
- can_reconfigure_alerts() returns incorrect current_alerts. Closes#3028
- Add missing header file. Closes#3065
The requirements of pin capabilites is different for spi master and
slave. The master needs CS, SCLK, MOSI to be output-able, while slave
needs MISO to be output-able.
Previous code is for master only.
This commit allows to place other 3 pins than MISO on input-only pins
for slaves. Refactoring for spi_common is also included.
Resolves https://github.com/espressif/esp-idf/issues/2455
New unit tests added
------------------------
**Local:** Local test uses the GPIO matrix to connect the master and the
slave on the same board. When the master needs the iomux, the master
uses the GPIOs of its own, the slave connect to the pins by GPIO matrix;
When the slave needs the iomux, the slave uses the GPIOs of its own, the
master connects to the pins by GPIO matrix.
- Provide a new unit test which performs freq scanning in mode 0. It
scans frequency of 1M, 8M, 9M and all frequency steps up to the maximum
frequency allowed.
**M & S**: Master & slave tests performs the test with two boards. The
master and slave use iomux or gpio matrix according to the config.
- Provide a new unit test which performs freq scanning in mode 0. It
scans frequency of 1M, 8M, 9M and all frequency steps up to the maximum
frequency allowed.
- Provide a new unit test which performs mode test with significant
frequencies. It tests mode 0,1,2,3 with low frequency, and the maximum
frequency allowed.
Paremeterized Test Framework
-----------------------------
The SPI has a lot of parameters, which works in the same process.
This framework provides a way to easily test different parameter sets.
The framework can work in two different ways:
- local test: which requires only one board to perform the test - master
& slave test: which generates two sub test items which uses the same
config set to cooperate to perform the test.
The user defines a (pair if master/slave) set of init/deinit/loop
functions. Then the test framework will call init once, then call loop
several times with different configurations, then call deinit.
Then a unit test can be appended by add a parameter group, and pass it into
a macro.
1. fix error when fading is too fast
2. fix error when setting duty and update immediately
3. update register header file to be in accord with TRM
closes https://github.com/espressif/esp-idf/issues/2903
1. Add missing get function to RMT API: rmt_get_idle_level().
2. Suppress error message from rmt_wait_tx_done() if wait_time==0 (allows for polling).
3. Remove the blank lines between parameter lists.
Merges https://github.com/espressif/esp-idf/pull/2666
closes https://github.com/espressif/esp-idf/issues/2494
closes https://github.com/espressif/esp-idf/pull/2493
closes https://github.com/espressif/esp-idf/pull/2496
1. Change bus reset to handle interrupted READ sequences.
2. Slow down I2C to 100khz during reset
3. If a SLAVE device was in a read operation when the bus was interrupted, the SLAVE device is controlling SDA.The only bit during the 9 clock cycles of a byte READ the MASTER(ESP32) is guaranteed control over, is during the ACK bit period.
If the SLAVE is sending a stream of ZERO bytes, it will only release SDA during the ACK bit period. The master(ESP32) cannot generate a STOP unless SDA is HIGH. So, this reset code synchronizes the bit stream with, Either, the ACK bit, Or a 1 bit.
I am stealing this delay coding from @jeremyherbert #2493 pr.
2. Change Bus Reset to handle interrupted READ sequences.
The current code does not handle interrupted READ cycles.
If a SLAVE device was in a read operation when the bus was interrupted, the SLAVE device is controlling SDA.
The only bit during the 9 clock cycles of a byte READ the MASTER(ESP32) is guaranteed control over, is during the ACK bit period.
If the SLAVE is sending a stream of ZERO bytes, it will only release SDA during the ACK bit period. The master(ESP32) cannot generate a STOP unless SDA is HIGH.
So, this reset code synchronizes the bit stream with, Either, the ACK bit, Or a 1 bit.
3. fix typo
correct `sda_id` to `sda_io` in `i2c_master_clear_bus()` @ryan-ma found it. This typo was generated when I manually edited this patch on GitHub, I should have done a Copy/Paste operation!
The DMA cannot receive data correctly when the buffer address is not
WORD aligned. Currently we only check whether the buffer is in the DRAM
region.
The DMA always write in WORDs, so the length arguments should also be
multiples of 32 bits.
A check is added to see whether the buffer is WORD aligned and has valid
length.
The driver decide whether use MOSI/MISO phases according to the buffer
address together with the SPI_TRANS_USE_*DATA. However someone may assue
that these phases will be skipped when the ``length``/``rxlength`` is
set to 0. In fact it is a feature that ``rxlength`` is allowed to be
set to 0 when tx and rx have the same length, and the driver fill the
``rxlength`` to ``length``.
An error check is added when the rxlength is 0 but there is data to be
sent.
It has been observed that, in case of underflow (data unavailability) in
I2S transmission, previously filled up tx descriptors continue to get
transmitted on line, causing noise in case of audio use case.
This change adds optional `tx_desc_auto_clear` field during I2S driver intialization
than can zero initialize tx descriptor in case of underflow situation in
interrupt handler itself.
Closes: https://github.com/espressif/esp-idf/issues/1789
Introduced in 9c23b8e5 and 4f87a62f. To get higher speed, menuconfig
options are added to put ISR and other functions into the IRAM. The
interrupt flag ESP_INTR_FLAG_IRAM is also mistakenly set when the ISR is
put into the IRAM. However callbacks, which are wrote by the user, are
called in the master and slave ISR. The user may not be aware of that
these callbacks are not disabled during flash operations. Any cache miss
during flash operation will cause panic.
Essentially IRAM functions and intrrupt flag ESP_INTR_FLAG_IRAM are
different, the latter means not disabling the ISR during flash
operations. New bus_config flag intr_flags is offered to help set the
interrupt attribute, including priority level, SHARED, IRAM (not
disabled during flash operations). It introduced a small BREAK to
IDFv3.1 (but the same as IDFv3.0) that the user has to manually set IRAM
flag now (therefore he's aware of the IRAM thing) to void the ISR being
disabled during flash operations.
New unity component can be used for testing other applications.
Upstream version of Unity is included as a submodule.
Utilities specific to ESP-IDF unit tests (partitions, leak checking
setup/teardown functions, etc) are kept only in unit-test-app.
Kconfig options are added to allow disabling certain Unity features.
It is an ESP specific FreeRTOS feature that the ISR is always executed
on the core which calls the interrupt register function. In the SPI
driver, the function is always called in the bus initialization
function.
Hence, the ISR will be executed on the core which initialize the driver.
If the core is starved due to higher priority ISRs, or the interrupt is
disabled on the core (spinlock called, etc.), the ISR will not get
executed and SPI transactions will not be handled.
(MINOR CHANGE)
Resolves https://github.com/espressif/esp-idf/issues/2432.
The MISO signal will be delayed if the GPIO matrix is enabled.
However, delay also comes from the slave.
Previous code only considers the former case, and assume the frequency
limitations is only violated when GPIO matrix is used.
Now we are able to calculate the freq limit when extenal MISO delay is
given (feature introduced in 9c6c6ec34ab0641ace89aeb9b1a133eb6fae1a18).
The frequency limit is lower when the external MISO delay is large, and
the limit is likely to be violated even with IOMUX.
Resolves https://github.com/espressif/esp-idf/issues/2690.
This commit resolves a blocking in esp_aes_block function.
Introduce:
The problem was in the fact that AES is switched off at the moment when he should give out the processed data. But because of the disabled, the operation can not be completed successfully, there is an infinite hang. The reason for this behavior is that the registers for controlling the inclusion of AES, SHA, MPI have shared registers and they were not protected from sharing.
Fix some related issue with shared using of AES SHA RSA accelerators.
Closes: https://github.com/espressif/esp-idf/issues/2295#issuecomment-432898137
This commit does the following
- Add power management lock to CAN driver so that APB frequency does not change
whilst CAN driver is in use
- Fix incorrect flag in can_transmit()
- Refactor can_driver_install() and can_driver_uninstall() so that critical sections
are shorter
- Fix CAN gpio configuration bug on RX pin. Closes#2302
- Add docs about multiple ID configuration and fix example links
Works for 3.3V eMMC in 4 line mode.
Not implemented:
- DDR mode for SD cards (UHS-I) also need voltage to be switched to 1.8V.
- 8-line DDR mode for eMMC to be implemented later.
For pins 32 and up the BIT(nr) macro used here overflowed,
causing undetermined GPIO pins to be reset.
Example: freeing SPI device/bus where CS is on pin 33
caused debug UART to cease communication, TXD0 was
disabled.
Fixed as BIT64(nr) macro, to be used elsewhere as needed.
For example in definitions like GPIO_SEL_32..GPIO_SEL_39.
This change adds a check for compatibility between the nvs version
found on nvs flash and the one assumed by running code during nvs
initialization. Any mismatch is reported to the user using new error
code ESP_ERR_NVS_NEW_VERSION_FOUND.
The test is previously disabled for the requirement of external
connection. Now the signals are connected by internal connections.
Also change the failure logic of the test.
Perviously host send_auto_stop flag would be set for every data
transfer over 1 block long. This caused stop commands to be sent
after CMD53, which shouldn't be done. Fix by adding an explicit list
of commands for which send_auto_stop should be set.
An existing UART driver does not support RS485 half duplex mode.
This task adds this functionality to ESP_IDF UART driver.
driver/uart.c/h: updated to add support of RS485 half duplex mode
examples/peripherals/uart_echo_rs485/main/rs485_example.c: added test example
components/driver/test/test_uart.c: added test of RS485 half duplex mode
docs/en/api-reference/peripherals/uart.rst: updated documentation
test_uart.c: suppress GCC warnings about discarded const qualifiers
uart.rst: remove sphinx warning - "Duplicate explicit target name"
simple change in uart.h file
update (test_uart.c) after rebase from master
update uart.rst, uart.c, rs485_example.c
Update example description in file Readme.md
update uart.c/h, uart.rst, test_uart.c according to review results
update uart.h (uart_set_rx_timeout() description
test_uart.c remove ignore tag
uart.c/h: fix param errors
test_uart.c: Remove GCC warning supress
uart.rst: fix the notes
rs485_example.c: fix output
uart.c: remove reset using UART_RXFIFO_RST from driver.
readme.md: Update example description
The tests are completed using RS485 adapters hardware connected to two ESP32 WROVER KITs.
TW#13812
Closes https://github.com/espressif/esp-idf/pull/667
Closes https://github.com/espressif/esp-idf/pull/1006
An existing UART driver does not support RS485 half duplex mode.
This task adds this functionality to ESP_IDF UART driver.
driver/uart.c/h: updated to add support of RS485 half duplex mode
examples/peripherals/uart_echo_rs485/main/rs485_example.c: added test example
components/driver/test/test_uart.c: added test of RS485 half duplex mode
docs/en/api-reference/peripherals/uart.rst: updated documentation
test_uart.c: suppress GCC warnings about discarded const qualifiers
uart.rst: remove sphinx warning - "Duplicate explicit target name"
simple change in uart.h file
update (test_uart.c) after rebase from master
update uart.rst, uart.c, rs485_example.c
Update example description in file Readme.md
update uart.c/h, uart.rst, test_uart.c according to review results
update uart.h (uart_set_rx_timeout() description
test_uart.c remove ignore tag
uart.c/h: fix param errors
test_uart.c: Remove GCC warning supress
uart.rst: fix the notes
rs485_example.c: fix output
The tests are completed using RS485 adapters hardware connected to two ESP32 WROVER KITs.
TW#13812
Closes https://github.com/espressif/esp-idf/pull/667
Closes https://github.com/espressif/esp-idf/pull/1006
An existing UART driver does not support RS485 half duplex mode.
This task adds this functionality to ESP_IDF UART driver.
driver/uart.c/h: updated to add support of RS485 half duplex mode
examples/peripherals/uart_echo_rs485/main/rs485_example.c: added test example
components/driver/test/test_uart.c: added test of RS485 half duplex mode
docs/en/api-reference/peripherals/uart.rst: updated documentation
test_uart.c: suppress GCC warnings about discarded const qualifiers
uart.rst: remove sphinx warning - "Duplicate explicit target name"
simple change in uart.h file
update (test_uart.c) after rebase from master
update uart.rst, uart.c, rs485_example.c
Update example description in file Readme.md
update uart.c/h, uart.rst, test_uart.c according to review results
update uart.h (uart_set_rx_timeout() description
test_uart.c remove ignore tag
uart.c/h: fix param errors
test_uart.c: Remove GCC warning supress
uart.rst: fix the notes
rs485_example.c: fix output
The tests are completed using RS485 adapters hardware connected to two ESP32 WROVER KITs.
TW#13812
Closes https://github.com/espressif/esp-idf/pull/667
Closes https://github.com/espressif/esp-idf/pull/1006
An existing UART driver does not support RS485 half duplex mode.
This task adds this functionality to ESP_IDF UART driver.
driver/uart.c/h: updated to add support of RS485 half duplex mode
examples/peripherals/uart_echo_rs485/main/rs485_example.c: added test example
components/driver/test/test_uart.c: added test of RS485 half duplex mode
docs/en/api-reference/peripherals/uart.rst: updated documentation
test_uart.c: suppress GCC warnings about discarded const qualifiers
uart.rst: remove sphinx warning - "Duplicate explicit target name"
simple change in uart.h file
update (test_uart.c) after rebase from master
update uart.rst, uart.c, rs485_example.c
Update example description in file Readme.md
update uart.c/h, uart.rst, test_uart.c according to review results
update uart.h (uart_set_rx_timeout() description
test_uart.c remove ignore tag
The tests are completed using RS485 adapters hardware connected to two ESP32 WROVER KITs.
TW#13812
Closes https://github.com/espressif/esp-idf/pull/667
Closes https://github.com/espressif/esp-idf/pull/1006
An existing UART driver does not support RS485 half duplex mode.
This task adds this functionality to ESP_IDF UART driver.
driver/uart.c/h: updated to add support of RS485 half duplex mode
examples/peripherals/uart_echo_rs485/main/rs485_example.c: added test example
components/driver/test/test_uart.c: added test of RS485 half duplex mode
docs/en/api-reference/peripherals/uart.rst: updated documentation
test_uart.c: suppress GCC warnings about discarded const qualifiers
uart.rst: remove sphinx warning - "Duplicate explicit target name"
simple change in uart.h file
update (test_uart.c) after rebase from master
update uart.rst, uart.c, rs485_example.c
Update example description in file Readme.md
update uart.c/h, uart.rst, test_uart.c according to review results
update uart.h (uart_set_rx_timeout() description
The tests are completed using RS485 adapters hardware connected to two ESP32 WROVER KITs.
TW#13812
Closes https://github.com/espressif/esp-idf/pull/667
Closes https://github.com/espressif/esp-idf/pull/1006
An existing UART driver does not support RS485 half duplex mode.
This task adds this functionality to ESP_IDF UART driver.
driver/uart.c/h: updated to add support of RS485 half duplex mode
examples/peripherals/uart_echo_rs485/main/rs485_example.c: added test example
components/driver/test/test_uart.c: added test of RS485 half duplex mode
docs/en/api-reference/peripherals/uart.rst: updated documentation
test_uart.c: suppress GCC warnings about discarded const qualifiers
uart.rst: remove sphinx warning - "Duplicate explicit target name"
simple change in uart.h file
update (test_uart.c) after rebase from master
update uart.rst, uart.c, rs485_example.c
Update example description in file Readme.md
update uart.c/h, uart.rst, test_uart.c according to review results
The tests are completed using RS485 adapters hardware connected to two ESP32 WROVER KITs.
TW#13812
Closes https://github.com/espressif/esp-idf/pull/667
Closes https://github.com/espressif/esp-idf/pull/1006
