Small changes to clock calibration value will cause increasing errors
the longer the device runs. Consider the case of deep sleep, assuming
that RTC counter is used for timekeeping:
- before sleep:
time_before = rtc_counter * calibration_val
- after sleep:
time_after = (rtc_counter + sleep_count) * (calibration_val + epsilon)
where 'epsilon' is a small estimation error of 'calibration_val'.
The apparent sleep duration thus will be:
time_after - time_before = sleep_count * (calibration_val + epsilon)
+ rtc_counter * epsilon
Second term on the right hand side is the error in time difference
estimation, it is proportional to the total system runtime (rtc_counter).
To avoid this issue, this change makes RTC_SLOW_CLK calibration value
persistent across restarts. This allows the calibration value update to
be preformed, while keeping time after update same as before the update.
1. For now, some security related functions used in classic Bluetooth are controlled by "SMP_ENABLE". This commit fixes the dependency.
2. The two options, "CLASSIC_BT_ENABLED" and "SMP_ENABLED" The two options will be decoupled in the future.
Currently libsodium tests add about 800kB to the binary, which is too
much for a partition table constrained to 2MB. Disable libsodium tests
until we start building multiple unit test apps for different subsets.
This fixes a bug introduced by !848, where APP CPU would not be reset
during esp_restart, if esp_restart was called from a task running on APP
CPU, and wouldn’t be reset by PRO CPU on startup.
This change replaces stalling APP CPU with resetting it.
Also adds a non-automated esp_restart tests.
DPORT access protection can not work when the other CPU is stalled.
Writes to DPORT registers in esp_restart caused the program to hang due
to access protection, and the reset happened due to RTC_WDT, not SW_RST.
This change adds esp_dport_access_int_deinit function and calls it from
esp_restart once the other core is stalled.
In ESP32 rev. 0, switching between 240MHz and 80MHz (even via an
intermediate frequency of 40MHz) may cause the chip to lock up.
The bootloader used to enable 80MHz CPU clock at startup, which could
cause lock up after software reset. With this change, if 240MHz CPU
clock is enabled in menuconfig, bootloader will also use 240MHz to avoid
lock-up.
Run some unit test cases based (poorly) around sodium's test infrastructure.
Increase in unity test task stack is due to signature tests, load a lot of data onto the stack.
- Fix slave initiate service discovery procedure
- Fix master re-discovery every time connection established
- Optimize service discovery char ccc write procedure
- Optimize esp_log_buffer function
- Modify default supervision timeout from 20s to 2s
This seems to clean up some of the more wrong addr2line output results (not
sure why, something to do with optimisations I think - perhaps the return
address may also be a jump target from some earlier line of the code.)
Previously, this resulted in task stack frames turning up incorrectly in the backtrace, ie
Backtrace: 0x400d22a0:0x3ffb0fa0 0x40085a3c:0x3ffb0fc0 0x400f32c4:0x3ffb0fe0 0x40081965:0x3ffb1010
0x400d22a0: esp_vApplicationIdleHook at /home/esp/esp-idf/components/esp32/./freertos_hooks.c:
52
0x40085a3c: prvIdleTask at /home/esp/esp-idf/components/freertos/./tasks.c:4431
0x400f32c4: i2c_isr_handler_default at /home/esp/esp-idf/components/driver/./i2c.c:598
0x40081965: _xt_lowint1 at xtensa_vectors.o:?
Fix is to implement abort() via an unhandled exception rather than a breakpoint, I think
because of relative priority of exception types.
Another approach would be to assign a software-only INUM to abort()ing and defined a
PANIC_RSN_ABORTED, but this is more complex and interrupt numbers are more scarce than RAM!
This change removes the erroneous cast to uint32_t (which caused time to
wrap around after 1 hour) and splits the multiplication into two terms
to remove the wraparound after 13 days.
Ref. https://esp32.com/viewtopic.php?f=13&t=1908
When ‘reset halt’ command is executed, OpenOCD will take the APP CPU
out of reset and enable the clock. At this point, user can set a
breakpoint on code which will run on APP CPU. Previously, app startup
code would do another reset of APP CPU, thereby removing any breakpoints
which may have been set. This change makes APP CPU reset conditional on
DPORT_APPCPU_CLKGATE_EN bit, which is 0 by default but is set to 1 by
OpenOCD after reset.
* Writing >4 bytes to unaligned offsets would fail
* Writiing data from flash would fail (wrong buffer was used)
* Writing >8192 bytes from RAM would over-write data multiple times
Adds test cases for the above.
Previously the first call to rmt_driver_uninstall() would remove the interrupt handler,
even if other channels still had the driver installed.
Adds an OS-level lock to control concurrent registration/deregistration of channels.
xPendingReadyList[1] was never initialised correctly, so if a task is added to this list (ie by xSemaphoreGiveFromISR()
or similar) while scheduler is disabled, then it causes a null pointer dereference.
Bug produces stack traces similar to:
0x40086e87: vListInsertEnd at /home/gus/esp/32/idf/components/freertos/./list.c:130
0x40084ba3: xTaskRemoveFromEventList at /home/gus/esp/32/idf/components/freertos/./tasks.c:3439
0x40083c54: xQueueGiveFromISR at /home/gus/esp/32/idf/components/freertos/./queue.c:2034
0x400f50a0: timer_group0_isr at /home/gus/esp/32/idf/components/freertos/test/./test_suspend_scheduler.c:27
0x40081d7d: _xt_lowint1 at xtensa_vectors.o:?
Writing values longer than half of the page size (with header taken into
account) causes fragmentation issues. Previously it was suggested on the
forum that using long values may cause issues, but this wasn’t checked
in the library itself, and wasn’t documented. This change adds necessary
checks and introduces the new error code.
Documentation is also fixed to reflect the fact that the maximum length
of the key is 15 characters, not 16.
component/bt: squash the branch of the early commit
component/bt: Added the set static random address callback to the bt project.
component/bt: fixed the set static random address error.
component/bt: fixed the set static random address error.
To increase the chances that the examples work out of the box, this
change is raising the default deep sleep wakeup delay to 1ms.
If GPIO15 is low at startup, ROM code takes less time to execute
(because no logging is performed), so more time may be needed to allow
flash chip to become ready.
Triggered on make 3.81, happens sometimes on Linux and always(?) on macOS. May depend on the order the OS' filesystem
resolves wildcards in.
Includes a revert to the LWIP component to verify this is properly fixed.
See also https://github.com/espressif/esp-idf/issues/632
Fix Dport access in interrupts
Dport accesses would re-enable interrupts unconditionally, breaking things when called in an ISR. This saves and restores the interrupt status, fixing this.
This fixes a crash in the SPI slave driver, and possibly other things.
See merge request !772
CI: auto generate configs for test jobs
Currently CI test jobs are static configured by several pre-generated config files.
This approach have several disadvantages:
1. not flexible to select test cases to run, which is important feature of @bot
2. difficult to update test as we need to pre-generate quite a lot files
3. need to maintain extra config files in IDF
4. not flexible to support new test apps or chips, can't use some new features of test bench
Therefore we'll add assign_test stage between build and test, to generate configs for test jobs.
See merge request !738
Make internal stack size variables in FreeRTOS 32-bit instead of 16-bit
Stock FreeRTOS uses an uint16 to store stack sizes, making it impossible to allocate a stack >64K. This changes this into an uint32, allowing for larger stacks.
See merge request !677
Partition table gen esp32part fixes: App offset errors, Python 3 support
As mentioned on forums, gen_esp32part.py wasn't erroring correctly if a non-64KB-aligned app partition was referenced.
Also merges a PR to add Python 2&3 support (with some tweaks). Not very useful in IDF right now, but useful for Arduino.
See merge request !751
1. Name change from chopper to carrier, block diagram update, minor changes to example codes
2. mcpwm_reg.h changed, brought uniformity in comments, worked on suggestions, duty to accept float. Some name changes!
3. Minor readme changes and Indetation
4. Minor change: move mcpwm_reg.h and mcpwm_struct.h to new path
5. Minor change: addition of BLDC example code and Readme
6. Name changed from epwm to mcpwm
7. Improve the reg name in mcpwm_struct.h
8. Name change chopper>carrier, deadband>deadtime
component/bt: fix the exception in attp_buil_sr_msg when handling gatt write bug. bug number #12124.
fix the exception in attp_buil_sr_msg when handling gatt write bug.
See merge request !743
Small unit-test-related fixes
Fixes for some small bugs found running unit tests with heap poisoning turned on.
All are bugs in the tests, except for one FreeRTOS fix (when deleting a task, check if it's running on the other CPU and preempt it if so.)
See merge request !746
nvs: remove search cache at page level
Since read cache was introduced at page level, search cache became
useless in terms of reducing the number of flash read operations.
In addition to that, search cache used an assumption that if pointers to
keys are identical, the keys are also identical, which was proven wrong
by applications which generate key names dynamically.
This change removes CachedFindInfo, and all its uses. This is done at
expense of a small extra number of CPU operations (looking up a value in
the read cache is slightly more expensive) but no extra flash read
operations.
Ref TW12505
Ref https://github.com/espressif/arduino-esp32/issues/365
See merge request !753
Since read cache was introduced at page level, search cache became
useless in terms of reducing the number of flash read operations.
In addition to that, search cache used an assumption that if pointers to
keys are identical, the keys are also identical, which was proven wrong
by applications which generate key names dynamically.
This change removes CachedFindInfo, and all its uses. This is done at
expense of a small extra number of CPU operations (looking up a value in
the read cache is slightly more expensive) but no extra flash read
operations.
Ref TW12505
Ref https://github.com/espressif/arduino-esp32/issues/365
1. Enlarge wifi task stack size by 512Bytes to fix potential stack overflow issue
2. Modify wifi hmac tx queue size from 12 to 32 because we already limit the buffer number in ebuf
management module
add API to get chip info
This change adds an API to get chip info, such as chip model, enabled capabilities, size of embedded flash, silicon revision.
Hello_world example is modified to print out the information about the chip. The example is also simplified by moving all code into the main task.
Ref TW12031.
See merge request !549
esp32: update wifi lib for some bugfix
1. Fix wifi ebuf free twice issue
2. Fix wifi internal assert issue
3. Fix a bug in esp_wifi_stop
4. Fix wifi crash issue
5. Fix wifi run out of memory when 10 udp connection stability test
See merge request !745
Optimize configuration of base MAC address
Application developer can call APIs to configure base MAC address
instead of using menuconfig.
See merge request !744
component/esp32 : fix dualcore bug
1. When dual core cpu run access DPORT register, must do protection.
2. If access DPORT register, must use DPORT_REG_READ/DPORT_REG_WRITE and DPORT_XXX register operation macro.
See merge request !742
component/bt: fix adv stop event bug and add attribute table create
- Fix bug that advertising stop event produced while calling start_adv function
- Modify gatt server adv data and scan rsp data raw setting
- Add create attribute table error msg
- Delete redundant printf in previous commits
See merge request !739
1. When dual core cpu run access DPORT register, must do protection.
2. If access DPORT register, must use DPORT_REG_READ/DPORT_REG_WRITE and DPORT_XXX register operation macro.
SPI: Various fixes (examples, mem leak, arg check)
- Fix SPI master example to use DMA-capable memory for display initialization. Fixes https://github.com/espressif/esp-idf/issues/551
- SPI master: Do not leak DMA descriptor pointer array on free
- SPI Master/Slave: Check if DMA'ed buffers actually live in DMA-capable memory
See merge request !735
error
- Fix bug that advertising stop event produced while calling start_adv function
- Modify gatt server adv data and scan rsp data raw setting
- add create attribute table error msg
- Delete redundant printf in previous commits
we'll auto assign cases to test jobs so we don't need those config
files. cases with different wifi modes will now be generated when
creating test case database, we need to remove them from YAML files.
FATFS fixes and tests
This MR includes a set of fixes related to FATFS, SDMMC, and wear levelling:
- `esp_vfs_fat_spiflash_mount` uses `FM_SFD` flag when creating the partition. The volume layout (given in `VolToPart` variable) was not compatible with SFD mode, so mkfs was failing. This fixes the volume layout to use "autodetect" for both volumes. Merges https://github.com/espressif/esp-idf/pull/559.
- fix `prepend_drive_to_path`function, which didn't prepend drive to path (while consuming 2k of stack space)
- fix stack overflow in vfs_fat_link function which allocated two 4kbyte `FIL` structures on the stack
- fix support for having two FATFS instances (in flash and SD) mounted at the same time
- unit tests written for FATFS on SDMMC are made common between SDMMC and WL implementations; FATFS unit tests on WL will run during CI
- fix inconsistent definition of PATH_MAX and ARG_MAX (TW12207, TW12104, https://github.com/espressif/esp-idf/issues/289)
See merge request !732
component/bt: fix some bugs related to bluetooth sniff mode in controller
1. fix some bugs in bluetooth sniff mode in controller
2. export some symbols to esp32.rom.ld including functions and global variables in ROM code
3. update libbtdm.a which includes "IRAM_ATTR" addition or removal for some functions
See merge request !729
fix(lwip): fix tcp connect fail when enable LOOPIF
when enable the LOOPIF, because of use the loopnetif, the TCP connect will fail. see TW12029
See merge request !711
- fix null pointer dereference in VFS when VFS implementations are added
and removed in different order
- vfs_fat_sdmmc, vfs_fat_spiflash: pass correct drive to mkfs
(previously it would always do mkfs in the first drive)
- add test case
This change moves actual test code into test_fatfs_common.c and
refactors setup/teardown code to be contained within separate functions.
For each SDMMC FATFS test, identical test is added which can run with
WL partition in flash.
vfs_fat_link opened two files to perform copy operation. File structures
were allocated on the stack. When _MAX_SS setting was increased in
ffconf.h due to wear levelling feature, the size of these structures
increased to ~4k each (~8k total). This exceeds stack size allocated for
tasks in most typical cases.
This change makes file structures dynamically allocated.
Originally, prepend_drive_to_path was designed to be a macro, and it
modified local path variables to point to a temporary buffers.
When it was converted into a function, modification to path variables
were no longer visible outside of this function.
In addition to that, prepend_drive_to_path allocated 2k bytes on the
stack for temporary path buffers. This is replaced with path buffers
allocated as part of vfs_fat context object. Locking is added around
parts of code which use these temporary buffers.
Additionally, _lock member of vfs_fat_ctx_t was placed after the
variable-sized files array, which caused the first entry in the
array to be never used. This change fixes the order of members
and adds comments.
1. fix some bugs in bluetooth sniff mode in controller
2. export some symbols to esp32.rom.ld including functions and global variables in ROM code
3. update libbtdm.a which includes "IRAM_ATTR" addition or removal for some functions
component/bt:fix the bug with gatt client cant not receive the gatt server service change event.
fix the bug with gatt client cant not receive the gatt server service change event.
See merge request !726
esp32: select 8M clock as RTC_FAST_CLK on startup
Even though RTC_CLK_CONFIG_DEFAULT correctly had RTC_FAST_FREQ_8M as the
fast clock, the bootloader modified fast_freq field to the currently
selected RTC_FAST_CLK (so that the clock choice is not affected by the
bootloader). The application startup code never switched to 8M clock,
which caused the default (XTAL/4) to be used as RTC_FAST_CLK. This had
caused a number of issues, such as touch pads not working in deep sleep.
Fixes https://github.com/espressif/esp-idf/issues/542.
Ref TW12053.
See merge request !709
Assert when a new task is started on a nonexisting CPU
Previously, starting a task on a CPU ID higher than the amount of CPUs FreeRTOS is configured with would not start the task and possibly have unintended side effects due to some out-of-bounds array writes. Assert on this so the app aborts cleanly.
See merge request !701
I2S driver - fixed support for 24 and 32-bits, fixed tx/rx at the same time
- Modify sample can test with 24, 32-bits audio
- Add i2s sample README
- simply i2s_push function
- change sample rates, bits per sample, channel on fly
See merge request !483
Fix SPI master CI test
CI test fails because the values it checks haven't been updated to the changes in the clock calculations. This fixes that.
See merge request !710
Feature/btdm ble bt separa
@Jack @snake @igrokhotkov @angus @island please help to review the code.
Separate the bt/ble code. After the separate, can save 15k~25k ram & 240k~460k code size(depending on the menuconfig).
See merge request !684
optimize scan before station connecting to AP
1. Store the information of AP(ssid, password, bssid, channel, etc)
into nvs when station connects to AP successfully. If station
connects to the same AP next time, it will scan the stored channel of the AP
first.
2. Add a parameter of channel for scanning before connecting to AP.
If the channel is set to 0, station will scan full channels. If it
is set to 1~13, station will only scan the channel.
See merge request !704
1. Store the information of AP(ssid, password, bssid, channel, etc)
into nvs when station connects to AP successfully. If station
connects to the same AP next time, it will scan the stored channel of the AP
first.
2. Add a parameter of channel for scanning before connecting to AP.
If it is set to 1~13, station will scan starting from the channel.
If the channel of AP is unknown, set it to 0.
Even though RTC_CLK_CONFIG_DEFAULT correctly had RTC_FAST_FREQ_8M as the
fast clock, the bootloader modified fast_freq field to the currently
selected RTC_FAST_CLK (so that the clock choice is not affected by the
bootloader). The application startup code never switched to 8M clock,
which caused the default (XTAL/4) to be used as RTC_FAST_CLK. This had
caused a number of issues, such as touch pads not working in deep sleep.
Fixes https://github.com/espressif/esp-idf/issues/542.
Ref TW12053.
Split common SPI stuff out of master driver; add slave driver; add workaround for DMA issue.
This merge req mainly adds a slave device. In order to do this, the original master driver is refactored into common code shared by master and slave modes, and a slave driver is added.
The other things added are:
- Added a workaround for a 'feature' of the ESP32 silicon that can lock up the receive DMA channel in some situations. This can only be fixed by resetting *both* DMA channels. The workaround implemented makes sure that the reset only happens when both channels are idle
- Got rid of the automatic choice between register- and DMA-based transfers. The master (and slave) code will now always go for a DMA transfer if a DMA channel is given, and always go for register-based transfers if no DMA channel is given.
- Add in a bunch of fixes for outstanding Github issues.
See merge request !659
Add support 24, 32 bits
@jxmao optimize i2s_zero_buffer
@jxmao correct config support slave mode
@jxmao correct setup pin support tx/rx at the same time
Enhance pin power
@jxmao add dynamic change number of channels
remove nvs_init
remove start log and enhance power pin setup
using enum for i2s_channel and i2s_bits_per_sample, return ESP_ERR_INVALID_ARG when check params
validate i2s_bits_per_sample and channel
check tx & rx buffer before fill zero
remove checking channel as @jxmao suggest
limit dma buffer
modify i2s pin back to gpio mux before configure gpio matrix, resolve github issue #512
Add support 24, 32 bits
reduce push function
Modify sample can test with 24, 32-bits
Add i2s sample README
Fixed i2s_set_clk got reset sometime
can changes bit-wide while running
Fix sample rate calculation for DAC mode from @jeroen
modify example can change bits per sample every 5 seconds
cleanup
add comment for bytes_per_sample
update as @angus suggestions
Add i2s_set_clk api
I2S driver bug fixed as following log:
@jxmao optimize i2s_zero_buffer
@jxmao correct config support slave mode
@jxmao correct setup pin support tx/rx at the same time
Enhance pin power
@jxmao add dynamic change number of channels
remove nvs_init
remove start log and enhance power pin setup
using enum for i2s_channel and i2s_bits_per_sample, return ESP_ERR_INVALID_ARG when check params
validate i2s_bits_per_sample and channel
check tx & rx buffer before fill zero
remove checking channel as @jxmao suggest
limit dma buffer
modify i2s pin back to gpio mux before configure gpio matrix, resolve github issue #512
limit dma buffer to 4092
change gpio_matrix_*_check to inline function, remove some comments and rename test_i2s function to setup_triangle_sine_waves
for change commit title
esp32: Core dump sanity checks
Adds sanity checks when doing core dump to flash
- CRC for core dump flash partition config
- Tasks with corrupted TCBs are skipped
- Assertions to check that nothing is written beyond core dump flash partition
Ref TW11879
See merge request !686
- CRC for core dump flash partition config
- Tasks with corrupted TCBs are skipped
- Assertions to check that nothing is written beyond core dump flash partition
add support for 32k XTAL as RTC_SLOW_CLK source
- RTC_CNTL_SLOWCLK_FREQ define is removed; rtc_clk_slow_freq_get_hz
function can be used instead to get an approximate RTC_SLOW_CLK
frequency
- Clock calibration is performed at startup. The value is saved and used
for timekeeping and when entering deep sleep.
- When using the 32k XTAL, startup code will wait for the oscillator to
start up. This can be possibly optimized by starting a separate task
to wait for oscillator startup, and performing clock switch in that
task.
- Fix a bug that 32k XTAL would be disabled in rtc_clk_init.
- Fix a rounding error in rtc_clk_cal, which caused systematic frequency
error.
- Fix an overflow bug which caused rtc_clk_cal to timeout early if the
slow_clk_cycles argument would exceed certain value
- Improve 32k XTAL oscillator startup time by introducing bootstrapping
code, which uses internal pullup/pulldown resistors on 32K_N/32K_P
pins to set better initial conditions for the oscillator.
Ref TW11683.
Ref https://esp32.com/viewtopic.php?f=13&t=1570
Fixes https://github.com/espressif/esp-idf/issues/337.
See merge request !696
- RTC_CNTL_SLOWCLK_FREQ define is removed; rtc_clk_slow_freq_get_hz
function can be used instead to get an approximate RTC_SLOW_CLK
frequency
- Clock calibration is performed at startup. The value is saved and used
for timekeeping and when entering deep sleep.
- When using the 32k XTAL, startup code will wait for the oscillator to
start up. This can be possibly optimized by starting a separate task
to wait for oscillator startup, and performing clock switch in that
task.
- Fix a bug that 32k XTAL would be disabled in rtc_clk_init.
- Fix a rounding error in rtc_clk_cal, which caused systematic frequency
error.
- Fix an overflow bug which caused rtc_clk_cal to timeout early if the
slow_clk_cycles argument would exceed certain value
- Improve 32k XTAL oscillator startup time by introducing bootstrapping
code, which uses internal pullup/pulldown resistors on 32K_N/32K_P
pins to set better initial conditions for the oscillator.
1.change the rowdata to rodata;
2.change BT_ACL_CONNECTIONS to Maximum BT/BLE connection count.
3. change the comments of bt_target.h:505 from 40 to 5.
wear levelling
This MR adds wear levelling component. It presents an interface similar to the interface of spi_flash and esp_partition. Inside, it stores data inside a partition to in a way that reduces worst case number of erase cycles for any given sector.
Also included are APIs similar to the ones provided for SDMMC to mount FAT filesystem on top of the wear levelling partition. A simple example shows how this API can be used.
Ref TW10338.
See merge request !567
- reorder directories listed in COMPONENT_SRCDIRS so that
subdirectories precede parent directories
- don’t include PPP source directories if PPP support is not enabled
1. close classic bt, can save 233k code size;
2. close smp module, can save 136k code size;
3. close gattc module, can save 24k code size;
4. close gatts module, can save 16k code size;
4. close the bluedroid stack log, can save 120k code size.
XTAL frequency detection, support for selecting XTAL frequency
This MR adds more robust XTAL frequency detection code (which gets run in the bootloader) and an option to set XTAL frequency in Kconfig. By default we still use autodetection, since it is more reliable than the one used in ROM code.
This will help with issues about XTAL frequency detection in high ambient temperature conditions.
Ref TW12008
See merge request !694
sdmmc: handle card removal when CD is not used
When SD card is removed during transaction, SDMMC peripheral can report
a range of errors, such as timeouts, CRC errors, start/end bit errors.
Under normal conditions (card is inserted), SDMMC peripheral also generates
command done or data done interrupts. When the card is removed, such
interrupts may not be always generated.
This change fixes handling of timeout interrupts and SBE interrupts.
It also adds a one second timeout into the event processing loop. This
timeout allows applications to recover in cases when the SDMMC peripheral
doesn’t generate command/data done event on card removal.
Fixes TW11592.
See merge request !678
fat/sdmmc: unmount FATFS object on error
Failure to call f_mount(NULL,...) makes FATFS attempt to clean up the old
FS object upon next mount. If previous mount operation has failed, some
parts of FS object may not be fully initialized, which will cause errors
(such as attempting to delete a mutex which wasn’t allocated).
Fixes TW11594.
See merge request !679
ROM code already implements XTAL frequency detection, but it uses the 8M
clock before the clock tuning parameters are initialized. With the
zero clock tuning parameter, 8M clock has significant frequency deviation
at high temperatures, which can lead to erroneous detection of 40 MHz
crystal as a 26 MHz one.
This change adds XTAL frequency detection code to rtc_clk_init routine,
and detection is performed after the 8M clock tuning parameter as been
initialized.
lwip: fix tcp stable test abort issue
This MR covers following changes:
1. Modify dhcp server timer to 1 seconds
2. Enable ETHARP_TRUST_IP_MAC. Consider following scenario: we are in throughput test or traffic stability test, if this option is disabled, then every 5 minutes, the IP/MAC entry in arch cache is aged out, however, the traffic continuously send to lwip from application, because there is no IP/MAC entry in ARP cache, then the packets have to be buffered in ARP queue and a ARP request is triggered, but the ARP queue can only holds 3 packets, the later packets will be dropped, then if the traffic is big, a lot of packets will be dropped here before we get the right ARP response. For TCP, this will trigger re-transmit, it's intolerable for some application, such as real time audio, if re-transmit happen, then performance of voice will be impact. For UDP, sometimes it may also cause problem, such as DHCP, if here we failed to send the DHCP here, we has to wait the DHCP timeout etc... so this option is enabled here by default.
See merge request !681
esp32: update wifi lib for limitting dynamic wifi buffer
Add limit for all dynamic wifi ebuf to avoid wifi run out of memory in some extreme scanrio.
The default max allocated dynamic tx buffer is 32
The default max allocated dynamic rx buffer is 64, make default value is bigger because when all packets we received are small packets, e.g. the length is 64Bytes, then 64K can hold 1000 packets, so 64 maybe a good candidate default value, anyway the customer can configure it via menuconfig.
The default dynamic wifi internal long/long-long mgmt is 32, generally 32 is enough for mgmt packet (beacon/auth/assoc/probe/null etc). Generally when all the 32 mgmt buffer is run out of memory, it means internal wifi state machine may has problem, we need to debug it.
See merge request !683
There are some RODATAs of libphy.a that are called in ISR. So need
to put them into DRAM to avoid access them when R/W SPI flash. Due
to the RODATAs which are called in ISR haven't been picked out to
put into DRAM, put all of the RODATA of libphy.a into DRAM. This
will be optimized in the future.
soc: allow REG_SET_FIELD to be used for bit fields
- Fixes an issue with `rtc_clk_apll_enable`: https://esp32.com/viewtopic.php?f=13&t=1673
- Fixes `rtc_clk_fast_freq_set` function always selecting XTAL/4 as fast clock source.
- Fixes regression in deep sleep current (7uA instead of 5uA).
See merge request !674
rtc_clk_init: handle case when XTAL frequency has already been set
On first reset, ROM code writes the estimated XTAL frequency into
RTC_APB_FREQ_REG (aka STORE5). If the application doesn’t specify exact
XTAL frequency (which is always the case for now), rtc_clk_init will
guess what kind of XTAL is used (26M or 40M), based on the estimated
frequency. Later, detected frequency is written into RTC_XTAL_FREQ_REG
(aka STORE4).
When the application switches clock source to PLL, APB frequency changes
and RTC_APB_FREQ_REG is updated. If the application encounters an RTC
WDT reset, RTC_APB_FREQ_REG will not be updated prior to reset. Once the
application starts up again, it will attempt to auto-detect XTAL
frequency based on RTC_APB_FREQ_REG, which now has value of 80000000.
This will fail, and rtc_clk_xtal_freq_estimate will fall back to the
default value of 26 MHz. Due to an incorrect XTAL frequency, PLL
initialization will also take incorrect path, and PLL will run at a
different frequency. Depending on the application this may cause just
garbage output on UART or a crash (if WiFi is used).
This change checks if RTC_XTAL_FREQ_REG has already been set before trying
to estimate XTAL frequency based on the value of RTC_APB_FREQ_REG, and
uses RTC_XTAL_FREQ_REG value if it is valid.
Fixes TW11738.
See merge request !691
Base MAC address can be stored in default manufacture-defined or customer
pre-defined place in EFUSE and other place e.g. flash or EEPROM.
If choose to use base MAC address which is stored in other place, please
call esp_base_mac_addr_set_external() before initializing WiFi/BT/Ehternet.
On first reset, ROM code writes the estimated XTAL frequency into
RTC_APB_FREQ_REG (aka STORE5). If the application doesn’t specify exact
XTAL frequency (which is always the case for now), rtc_clk_init will
guess what kind of XTAL is used (26M or 40M), based on the estimated
frequency. Later, detected frequency is written into RTC_XTAL_FREQ_REG
(aka STORE4).
When the application switches clock source to PLL, APB frequency changes
and RTC_APB_FREQ_REG is updated. If the application encounters an RTC
WDT reset, RTC_APB_FREQ_REG will not be updated prior to reset. Once the
application starts up again, it will attempt to auto-detect XTAL
frequency based on RTC_APB_FREQ_REG, which now has value of 80000000.
This will fail, and rtc_clk_xtal_freq_estimate will fall back to the
default value of 26 MHz. Due to an incorrect XTAL frequency, PLL
initialization will also take incorrect path, and PLL will run at a
different frequency. Depending on the application this may cause just
garbage output on UART or a crash (if WiFi is used).
SPI transfer length is bits, not bytes, so the error should indicate bits. Also, there are separate lengths for rx and
tx (confusingly named rxlength and length... if rxlength is 0, length is used). The code checks the tx length for the
rx, so it never validates rxlength.
Originally contributed as part of #511https://github.com/espressif/esp-idf/pull/511
Since mbedtls_net_errno is reset by fcntl, it is reset after calling
net_would_block, so the call to mbedtls_net_errno in mbedtls_net_recv
and mbedtls_net_send will always get back 0. This change propagates
the value returned by mbedtls_net_errno up through net_would_block,
to allow the correct error value to be used and avoid a redundant
call to mbedtls_net_errno.
Merges PR #511https://github.com/espressif/esp-idf/pull/511
Failure to call f_mount(NULL,...) makes FATFS attempt to clean up the old
FS object upon next mount. If previous mount operation has failed, some
parts of FS object may not be fully initialized, which will cause errors
(such as attempting to delete a mutex which wasn’t allocated).
When SD card is removed during transaction, SDMMC peripheral can report
a range of errors, such as timeouts, CRC errors, start/end bit errors.
Under normal conditions (card is inserted), SDMMC peripheral also generates
command done or data done interrupts. When the card is removed, such
interrupts may not be always generated.
This change fixes handling of timeout interrupts and SBE interrupts.
It also adds a one second timeout into the event processing loop. This
timeout allows applications to recover in cases when the SDMMC peripheral
doesn’t generate command/data done event on card removal.
Remove ESP_EARLY_LOGI before bss is initialized; it crashes the CPU
There's an ESP_EARLY_LOGI line that can get called before the BSS is initialized; the early logging code doesn't cope well with that: it checks if FreeRTOS is up, but the variables it uses for that contains garbage because it isn't cleared yet, giving the wrong result. The logging code then tries to set a mux, crashing the entire system. This patch removes the log line and adds a warning at the BSS initialization line not to do anything complex before that point.
Fixes https://github.com/espressif/esp-idf/issues/523
See merge request !671
- Implements application tracing module which allows to send arbitrary
data to host over JTAG. This feature is useful for analyzing
program modules behavior, dumping run-time application data etc.
- Implements printf-like logging functions on top of apptrace module.
This feature is a kind of semihosted printf functionality with lower
overhead and impact on system behaviour as compared to standard printf.
component/bt: transfer bluedroid timer events to be handled by BTC task
NVS operation can take long time for timer task to handle. Transfer the alarm event to be handled by BTC task.
See merge request !670
Detect invalid cache access
This MR adds always-on feature which detects cache invalid access and triggers panic handler when invalid access interrupt is raised.
See merge request !660
Confusion here is that original ROM has two functions:
* SPIReadModeCnfig() - sets mode, calls enable_qio_mode/disable_qio_mode
* SPIMasterReadModeCnfig() - As above, but doesn't set QIO mode in status register
However we never want to use the ROM method to set/clear QIO mode flag, as not all flash chips work this way. Instead we
do it in flash_qio_mode.c in bootloader.
So in both cases (ROM or "patched ROM") we now call SPIMasterReadModeCnfig(), which is now named
esp_rom_spiflash_config_readmode().
Fix uart tx function block issue
To enable tx empty interrupt each time the tx ringbuffer get filled, so that tx function will not block if tx data length is larger than tx ringbuffer size.
Reported from customer of Audio team.
See merge request !658
give the AP and STA netifs different names for ease of debugging lwip
Both AP and STA netifs used to be called "en". This changes the name to "st" for STA and "ap" for AP.
Ref https://github.com/espressif/esp-idf/pull/456.
See merge request !653
Feature/btdm avrc
The source branch "feature/btdm_avrc" includes classic Bluetooth profiles A2DP(sink role) and AVRCP(controller role);
Menuconfig options to control whether to enable classic BT is added.
See merge request !591
Enable checks for encrypted flash in OTA
Even if firmware is compiled without CONFIG_FLASH_ENCRYPTION_ENABLED.
Rationale: CONFIG_FLASH_ENCRYPTION_ENABLED controls whether boot loader generates keys for encryption or not, but flash encryption can be configured externally. With this change, it's possible to have boot loader not generate keys but still have encryption working.
Also fix use of it->part
Ref. https://github.com/espressif/esp-idf/pull/453
See merge request !647
To enable tx empty interrupt each time the tx ringbuffer get filled, so that tx function will not block if tx data length is larger than tx ringbuffer size.
Reported from customer of Audio team.
bt component: Fix memory leak while using gatt server
- fix memory leak while creating attribute table
- fix memory leak while deleting service
See merge request !656
Introduce soc component, add source of rtc_clk and rtc_pm libraries
This MR adds parts of the RTC library source code (initialization, clock selection functions, sleep functions). WiFi-related power management functions are kept inside the precompiled library. Most of RTC library APIs have been renamed.
Default CPU frequency option in Kconfig is set to 160MHz, pending qualification of 240MHz mode at high temperatures.
Register header files are moved into the new soc component, which will contain chip-specific header files and low-level non-RTOS-aware APIs (such as rtc_ APIs). Some of the files from ESP32 component were also moved: cpu_util.c, brownout.c, and the corresponding header files. Further refactoring of ESP32 component into more meaningful layers (chip-specific low level functions; chip-specific RTOS aware functions; framework-specific RTOS-related functions) will be done in future MRs.
See merge request !633
Bugfix/flash busy check wait spi idle
This branch moves some ROM SPI flash driver to IDF to fix bug in Wait_SPI_Idle() function.
Also it applies code style rules of IDF to integrated ROM driver sources.
See merge request !584
Even if firmware is compiled without CONFIG_FLASH_ENCRYPTION_ENABLED
Rayionale: CONFIG_FLASH_ENCRYPTION_ENABLED controls whether boot loader
generates keys for encryption or not, but flash encryption can be
configured externally. With this change, it's possible to have boot
loader not generate keys but still have encryption working.
Also fix use of it->part
1) fixed SPI_read_status: added check for flash busy flag in matrix mode
2) fixed SPI_page_program: enable write before writing data to SPI FIFO
3) SPI flash ROM funcs replacement is controlled via menuconfig option
CI: add reset between running each unit test cases
Unit test is designed to detect bug **within** each test case. Therefore we'll reset between each case to provide a clean context. We will later add stress cases to run unit test cases together to detect potential bugs.
See merge request !636
esp32: initialize cross-core interrupt in single core mode
The software interrupt originally used as the cross-core interrupt is
now also used to yield from a FreeRTOS critical section; therefore it
must be initialized for single core mode as well.
Fixes https://github.com/espressif/esp-idf/issues/496
See merge request !640
fix warnings generated by ESP_ERROR_CHECK(variable) in release builds
This uses the same pattern as “assert” in release builds to silence the
warning. At the same time, we make sure that if a statement is wrapped
into ESP_ERROR_CHECK, it is executed in release build as well.
Fixes https://github.com/espressif/esp-idf/issues/497
See merge request !641
This uses the same pattern as “assert” in release builds to silence the
warning. At the same time, we make sure that if a statement is wrapped
into ESP_ERROR_CHECK, it is executed in release build as well.
The software interrupt originally used as the cross-core interrupt is
now also used to yield from a FreeRTOS critical section; therefore it
must be initialized for single core mode as well.
Fixes https://github.com/espressif/esp-idf/issues/496
esp32: RWDT is used to reboot system in case of panic handler crash
This branch uses RWDT to reboot system in case of panic handler crash.
See merge request !625
Feature/btdm uart hci
1. support UART HCI, devolper need not to make a bridge between VHCI and UART.
2. fix bug of rand/srand called in ISR.
3. fix bug of BLE rx packets may cause assert.
See merge request !626
component/bt : modify alarm APIs to be safely accessible from multiple tasks
Improve the osi_alarm module to make the alarm APIs become thread safe.
See merge request !570
1. support UART HCI, devolper need not to make a bridge between VHCI and UART.
2. fix bug of rand/srand called in ISR.
3. fix bug of BLE rx packets may cause assert.
lwip: implement lwip critical session with mutex
Currently lwip critical session is based on interrupt, now replace it with mutex
See merge request !595
spi_flash: fix race condition in s_flash_op_complete access
Flash operation complete flag was cleared by the CPU initiating flash operation. If the other core was running an ISR, then IPC task could be late to enter the loop to check `s_flash_op_complete` by the time next flash operation started. This would cause a deadlock, as the IPC task would still be waiting for `s_flash_op_complete` to be set (which was already cleared by the next flash operation), while the flash operation task would be blocked waiting for IPC task to set `s_flash_op_can_start`.
If the flag is cleared on the CPU waiting on this flag, then the race condition can not happen.
See merge request !615
Fix timing adjustment needed for higher speeds of SPI master bus.
Ref https://github.com/espressif/esp-idf/issues/363 . It was found out the master SPI driver didn't exactly calculate the delay compensation needed, breaking 20 and 26MHz full-duplex mode. This fixes these use cases. We also found out 40MHz full-duplex routed over the GPIO matrix does not work because of a hardware quirk; this MR adds a check/error for that case until we find a workaround.
See merge request !547
If static tx buffer is selected, WiFi tx buffers are allocated when WiFi is initialized and released
when WiFi is de-initialized. If dynamic tx buffer is selected, WiFi tx buffer is allocated when tx
data is delivered from LWIP to WiFi and released when tx data is sent out by WiFi.
The size of each static tx buffers is fixed to about 1.6KB and the size of dynamic tx buffers is
depend on the length of the data delivered from LWIP.
If PSRAM is enabled, "STATIC" should be selected to guarantee enough WiFi tx buffers.
If PSRAM is disabled, "DYNAMIC" should be selected to improve the utilization of RAM.
Fix finding location of ISR stack space for CPU1
Up to now, the CPU1 interrupts erroneously used the area *after* the ISR stack region, leading to bugs in BT Classic. This fixes that.
See merge request !618
Flash operation complete flag was cleared by the core initiating flash
operation. If the other core was running an ISR, then IPC task could
be late to enter the loop to check s_flash_op_complete by the time next
flash operation started. If the flag is cleared on the CPU waiting on
this flag, then the race condition can not happen.
ULP coprocessor toolchain integration
- build system support for ULP coprocessor toolchain
- documentation for ULP coprocessor instruction set
- documentation for ULP code execution flow, loading programs, exchanging data
- example: counting pulses using ULP
See merge request !394
Reset WIFI mac when wifi start and update wifi lib
1. reset wifi mac when wifi start
2. roll back rx hung workaround for beacon timeout
3. fix amsdu ap interface wrong issue
4. fix amsdu header parse error
5. fix amsdu flag wrong issue
6. PHY: V350, fix BT rssi bug
7. RTC: V225, fix bt will be not work when wifi is reset
See merge request !606
SPI flash operations lock for shorter periods
Based on bug report here:
https://esp32.com/viewtopic.php?f=13&t=1489&p=6816#p6773
Long SPI flash erase (and possibly write/read) cycles block all tasks on both CPUs for an extended period, and can lead to WiFi dissassociation (and general priority inversion.)
This MR inserts preemption breaks into large operations (all erases, writes every 8KB, reads every 16KB).
Overhead of a single spi_flash_guart_start()/spi_flash_guard_end() cycle measured at approx 67us (assuming no preemption.)
See merge request !600
bugfix: ESP32 Core Dump reported issues
This MR fixes the following issues:
1. fixed path to esptool when there is no compiled python module for it
2. GDB inernal failure handling was added
See merge request !599
Error handling in NVS initialization
Previously nvs_flash_init worked under an assumption that there should always be at least one free page available. This is true during normal operation, but in some cases (such as when changing application partition table from a non-OTA to an OTA one), NVS partition may get truncated, which will cause empty pages to be lost.
This MR adds error checks for this condition, and updates code which calls `nvs_flash_init` to check for the return code.
For most examples, a simple `ESP_ERROR_CHECK` is added around `nvs_flash_init`. For NVS examples and the OTA example, more robust error handling is added.
This change also removes nvs_flash_init calls from examples which don't use NVS.
See merge request !582
idf_monitor: Small fixes (baud rate, EOL, /dev/tty.X on macOS, Ctrl-T on failure)
* "make monitor" now passed the configured baud rate.
Closes#436https://github.com/espressif/esp-idf/issues/436
* Pass toolchain prefix from sdkconfig into monitor tool
* Allow setting EOL in idf_monitor.py, use CRLF by default
* Detect if /dev/tty.X is used on macOS, warn and replace with /dev/cu.X
* If a build fails or gdb exits, ignore Ctrl-T (allowing Ctrl-T Ctrl-A/F to be same key sequence everywhere)
* Add a note about winpty on Windows.
Ref 02fdf8271d (commitcomment-21369196)
* Fix problems with Console.cancel() not existing in older pyserial
* Print more user-friendly symbols for "start of iram" and "start of flash"
See merge request !594
1. reset wifi mac when wifi start
2. roll back rx hung workaround for beacon timeout
3. fix amsdu ap interface wrong issue
4. fix amsdu header parse error
5. fix amsdu flag wrong issue
6. PHY: V350, fix BT rssi bug
7. RTC: V225, fix bt will be not work when wifi is reset
* Erase range operations allow preemption after each block or sector.
* Write operations allow preemption every 8KB of data.
* Reado operations allow preemption every 16KB of data.
This is to avoid confusion when idf_monitor prints the first symbol in each section, ie "WindowOverflow4" or similar,
when bootloader prints the section mapping address.
Closes#447https://github.com/espressif/esp-idf/issues/447
* "make monitor" not passed the configured baud rate
Closes#436https://github.com/espressif/esp-idf/issues/436
* Pass toolchain prefix from sdkconfig into monitor tool
* Allow setting EOL in idf_monitor.py, use CRLF by default
* Detect if /dev/tty.X is used on macOS, warn and replace with /dev/cu.X
* If a build fails or gdb exits, ignore Ctrl-T (allowing Ctrl-T Ctrl-A/F to be same key sequence everywhere)
* Add a note about winpty on Windows
Ref 02fdf8271d (commitcomment-21369196)
modify touch pad read function
The touch pad read function taks too much time within spin lock waiting for the "done bit". (about 7.6ms as we tested)
So we try to use a mutex on the touch read function and any other functions might change the "done bit".
See merge request !543
This issue is reported from https://github.com/espressif/esp-idf/issues/304.
We found that when we operate the hw command registers in I2C struct, sometimes the behaviour would be different in DEBUG/RELEASE optimisation level:
The code looks like this:
I2C[i2c_num]->command[p_i2c->cmd_idx].byte_num -= 0;
In DEBUG configuration:
I2C[i2c_num]->command[p_i2c->cmd_idx].byte_num -= 0;
400f3ab0: 3388 l32i.n a8, a3, 12
400f3ab2: 14c882 addi a8, a8, 20
400f3ab5: a08840 addx4 a8, a8, a4
400f3ab8: 0020c0 memw
400f3abb: 2898 l32i.n a9, a8, 8
400f3abd: 0020c0 memw
400f3ac0: 28b8 l32i.n a11, a8, 8
400f3ac2: 74a090 extui a10, a9, 0, 8
400f3ac5: 00af92 movi a9, 0xffffff00
400f3ac8: 109b90 and a9, a11, a9
400f3acb: 2099a0 or a9, a9, a10
400f3ace: 0020c0 memw
400f3ad1: 2899 s32i.n a9, a8, 8
In RELEASE configuration:
I2C[i2c_num]->command[p_i2c->cmd_idx].byte_num -= 0;
400f2ba2: 580572 l8ui a7, a5, 88
400f2ba5: 747070 extui a7, a7, 0, 8
400f2ba8: 0020c0 memw
400f2bab: 584572 s8i a7, a5, 88
Looks like the compiler will make it a 8bit operation after optimisation.
But the register value changes from 0x901 to 0x101.
After this 8-bit optimisation, the 11th bit changed from 1 to zero, which caused this error.
We are still trying to find out why that happens, because there might be some risk when operating the register struct.
This is a workaround to avoid "-=" operation on I2C register struct fields.
1. Add low speed channels for LEDC module.
2. Improve fade object allocate mechanism.
3. Improve ledc example, add 2 low speed channels in example.
4. Remove debug code
5. Improve the register bit field name of slow clock.
esp32: update wifi lib for some bugfix/features
1. add options to disable nvs
2. add station keepalive with softap
3. fix beacon rx start time not accurate issue
4. set wifi rx desc/buffer boundary check to internal memory boundary
See merge request !578
nvs_flash_init may return an error code in some cases, and applications
should check this error code (or at least assert on it being ESP_OK, to
make potential issues more immediately obvious).
This change modifies all the examples which use NVS to check the error
code. Most examples get a simple ESP_ERROR_CHECK assert, while NVS
examples, OTA example, and NVS unit tests get a more verbose check which
may be used in real applications.
Expand 'make monitor' support
New 'make monitor' idf_monitor tool for better monitor output. Running 'make monitor' will now:
* Automatically look up code addresses via addr2line and print function, source file, line number in terminal.
* Can reset the ESP32 by typing Ctrl-T Ctrl-R.
* Can run "make flash" by typing Ctrl-T Ctrl-F.
* Can run "make app-flash" by typing Ctrl-T Ctrl-A.
* If gdb stub starts, monitor will automatically run gdb and connect. When gdb exits, ESP32 resets and monitor resumes.
* Exit is still Ctrl-[
Have some more features I'd like to add (log output to file, crash dump support) but I think this is at the point of being useful.
See merge request !565
This change adds a check for the free page count to nvs_flash_init.
Under normal operation, NVS keeps at least one free page available,
except for transient states such as freeing up new page. Due to external
factors (such as NVS partition size reduction) this free page could be
lost, making NVS operation impossible. Previously this would cause an
error when performing any nvs_set operation or opening a new namespace.
With this change, an error is returned from nvs_flash_init to indicate
that NVS partition is in such a state.
make: don’t override TEST_COMPONENTS
When idf_monitor is launched from make, it gets modified `TEST_COMPONENTS`
variable which contains full paths to the test components instead of the
names. This causes `TEST_COMPONENT_PATHS` to be empty and the unit test
app gets built without any test components.
This change introduces an internal `TEST_COMPONENTS_LIST` variable which
gets set either from `COMPONENTS` if `TESTS_ALL` is 1, or from
`TEST_COMOPONENTS` otherwise.
Bootloader makefile is also fixed to avoid propagating `TESTS_ALL` to the
bootloader build step.
See merge request !569
bug fix: fix uart data bug when stop-bit is set as 2-bit mode
This is a workaround for a hardware bug.
When we want to use 2-stop-bit mode, we need to set stop-bit-1 and set dl1_en in rs485 register.
See merge request !544
1. add options to disable nvs
2. add station keepalive with softap
3. fix beacon rx start time not accurate issue
4. set wifi rx desc/buffer boundary check to internal memory boundary
The touch pad read function taks too much time within spin lock waiting for the "done bit". (about 7.6ms as we tested)
So we try to use a mutex on the touch read function and any other functions might change the "done bit".
When idf_monitor is launched from make, it gets modified TEST_COMPONENTS
variable which contains full paths to the test components instead of the
names. This causes TEST_COMPONENT_PATHS to be empty and the unit test
app gets built without any test components.
This change introduces an internal TEST_COMPONENTS_LIST variable which
gets set either from $(COMPONENTS) if TESTS_ALL is 1, and from
TEST_COMOPONENTS otherwise.
Bootloader makefile is also fixed to avoid propagating TESTS_ALL to the
bootloader build step.
bt component: fix bluetooth gatt packets process bugs
1. Add process of prepare write request packets
2. Add process of execute write request packets
3. Add process of reliable write request packets
4. Fix bug of processing read blob request packets
5. Fix bug of processing write request packets
6. Optimize error check and process in stack
See merge request !558
add wakeup from touch sensor, and deep sleep example
- add new deep sleep wakeup mode
- change documentation to explain incompatibilities between different wakeup mode, add error checks
- add new ULP instructions necessary for ULP wakeup scenario
- fix issues with I_WR_REG, I_SLEEP, I_END instructions
- add deep sleep example, illustrating the use of timer, gpio, touch, and ULP wakeup triggers
See merge request !461
add extra check before bluedroid init and disable
add extra check before bluedroid init and disable to avoid the mixed call cause unexpected errors.
See merge request !553
component/bt: optimize stack size of Bluetooth Tasks and make them be configurab…
Bluetooth tasks' stack size are optimized and can be configured by the CONFIG_NEWLIB_NANO_FORMAT option.
See merge request !559
esptool version bump and new "espefuse.py set_flash voltage" command
* New "espefuse.py set_flash_voltage" command to easily set a fix
VDD_SDIO regulator voltage (1.8V, 3.3V or disabled).
* Fixes bugs when flashing files with non-4-byte aligned lengths
(doesn't effect esp-idf image files)
* esptool README improvements
* Detect overlapping files in write_flash
* read_mac now works correctly on ESP32
* Integrates reset fix for older dev boards (formerly the "Windows ESP32R0 reset workaround")
See merge request !481
Change max number of open sockets
Change max number of open sockets from 16 to 32 because of MFI project need support 21 open sockets at least.
See merge request !532
1. Add process of prepare write request packets
2. Add process of execute write request packets
3. Add process of reliable write request packets
4. Fix bug of processing read blob request packets
5. Fix bug of processing write request packets
6. Optimize error check and process in stack
Fix partition- and mmap-related issues
- Fix unit tests failing to start up due to a mismatch between sdkconfig flash size and size required by partition table.
- Fix a bug that partition APIs loaded the partition table in reverse order. As such, `esp_partition_next` and `esp_partition_find_first` did not work as expected. Add a test.
- Update the workaround for stale cache reads issue: do Cache_Flush for non-encrypted flash as well. Add a test.
See merge request !555
The issue that cache entries are not invalidated correctly sometimes
can also be reproduced for non-encrypted flash as well.
This change updates the workaround to do Cache_Flush, enabling it for
non-encrypted flash, and adds a unit test.
- change order of assert arguments to (expected, actual)
- set expected partition count to 3 to match the new partition table
- use the new get_test_partition facility
- check that partitions are listed in correct order
- remove leftover debugging printfs
Originally marked "Reset with ESP32R0 Windows workaround", but proven to be
necessary on some other platforms as well. This is now integrated into the
default esptool.py reset behaviour.
Closes#305https://github.com/espressif/esp-idf/issues/305
* New "espefuse.py set_flash_voltage" command to easily set a fix
VDD_SDIO regulator voltage (1.8V, 3.3V or disabled).
* Fixes bugs when flashing files with non-4-byte aligned lengths
(doesn't effect esp-idf image files)
* README improvements
Allow separate ethernet & wifi configuration
If only 1/2 of ethernet & WiFi are enabled in config, the other interface is no longer linked into the firmware.
* Fixes bug where enabling Ethernet but not WiFi would fail to compile.
* Also means that enabling WiFi but not Ethernet no longer links some unused ethernet interface functions.
See merge request !525
FreeRTOS: Fix cross-core event group sync
As above
Also includes fixes which allowed removing some semi-hacky bits from the event group unit tests - specifically, higher priority tasks will always be started immediately even if they run on the opposite core.
See merge request !535
FATFS enable support for multiple drives
Current implementation has drive numbers and paths hardcoded to support
only one FATFS drive. Arduino has it's own SPI driver to allow
compatibility and flexibility. With the MR it is possible to have up to
```_VOLUMES``` drives connected (SPI, SDMMC and others) at the same
time and accessed through VFS
See merge request !478
freertos kconfig: Add max task length name, move task stack overflow watchpoint
* Allow setting task name length via kconfig
* Move task stack overflow watchpoint out of internals debugging submenu, place next to other stack overflow checks.
* Thread local pointer feature should depend on Ethernet or WiFi
See merge request !531
Partition/SPI/OTA docs & OTA new functionality
* Update partition, SPI flash & OTA docs to reflect functionality changes
* Refactor OTA implementation to perform checks mentioned in API doc
* Add new functions to OTA API: esp_ota_get_running_partition() & esp_ota_get_next_update_partition() functions
* Add spi_flash_cache2phys() & spi_flash_phys2cache() functions to support esp_ota_get_running_partition()
See merge request !513
Feature/add user set mac
1. Add menuconfig for user to set mac address of wifi, bt and ethernet.
2. Add the number of MAC address generated from efuse for user to choose.
3. Add MAC address derive method.
See merge request !542
esp32: Fix hardware rng after esp_wifi_stop (second implementation)
Ensures hardware RNG remains enabled at all times.
Reworked version of !534
See merge request !536
lwip: modify dhcp timer granularity from 60s to 1s
Current DHCP granularity is 60 seconds, it's not accurate, it can cause DHCP release/rebind/renew timer
timeout at the same time, also it may renew/rebind/release at wrong time, thus cause problem.
1. RTC V214: modify APLL function for the chip of ECO version.
2. Add API phy_close_rf() and use it in esp_phy_deinit() instead of pm_close_rf().
3. RTC V213: fix BT will not work when BT-init is called more than once.
vfs_fat_sdmmc: if card init fails, fail cleanly
This fixes the issue with sdmmc_host not returned to clean state after a failed attempt to mount the card, with no SD card in the slot.
See merge request !527
component/bt : add adv/scan start complete event
1. indicate adv/scan start complete success or failed
2. controller do limit of adv/scan concurrence, so add some codes to report adv/scan start failed or not.
See merge request !524
component/bt:fixed the write ccc crash bug error
fix the gatt server write ccc lead to the system crash if not initialize the ccc value.
See merge request !515
Optimize or release memory in bluetooth
1. add option to release about 30K from BT if BLE only
2. later BT/BLE will be separated by BT/BLE macro, but this option should use when user make sure that in BLE only mode.
See merge request !520
1. indicate adv/scan start complete success or failed
2. controller do limit of adv/scan concurrence, so add some codes to report adv/scan start failed or not.
The root cause is the bug in bluetooth controller, in which the HCI_SNIFF_MODE command is sent to controller and at the same time the controller has received same request from remote device.
For now change the time-out period of local device to enter the SNIFF mode.
Fix a scheduling bug
Fixes:
- Trivial bug where in some special cases a task could be started on the wrong core (and would run there for max 1 tick)
- More major bug causing a yield to be done with a mux held.
See merge request !523
Fix SPI master transmit length
Tx/Rx length fix from https://github.com/espressif/esp-idf/pull/336
I also added an extra commit in to make use of a define instead of a literal, plus fix a (harmless) off-by-one condition.
See merge request !521
This fixes incorrect descriptions of I_END/I_SLEEP instructions and
changes the definition of I_END. New instruction, I_WAKE, is added,
which wakes up the SoC. Macro for ADC instruction is defined, and new
tests are added.
This change adds esp_deep_sleep_get_wakeup_cause, which returns the
source which has caused wakeup from deep sleep.
Similar to esp_deep_sleep_get_ext1_wakeup_status, a function is added
to check touch pad wakeup status: esp_deep_sleep_get_touchpad_wakeup_status.
This function returns the touch pad which has caused wakeup.
ULP and touch FSMs in ESP32 revisions 0 and 1 do not operate correctly
if RTC_PERIPH power domain is force powered on (ESP_PD_OPTION_ON).
Both ULP and touch still work, but clock frequency of the ULP may be
incorrect and touch values may be off by considerable amount. As such,
when these wakeup modes are used, RTC_PERIPH power domain has to be set
to ESP_PD_OPTION_AUTO (or, in the current implementation,
ESP_PD_OPTION_OFF — though this will change in the future when _OFF will
actually *force* the power domain to be powered off).
Because EXT0 wakeup source requires RTC_PERIPH to be powered ON, mark
ULP and touch wakeup sources as incompatible with EXT0. Workaround for
this is to use EXT1 wakeup source instead, which offers similar or
better functions without having to keep RTC_PERIPH powered on.
- I_RD_REG used the wrong union member (.rd_reg) due to a copy-paste
mistake
- Peripheral register address in bits[7:0] should be given in words,
not in bytes
Fixes https://github.com/espressif/esp-idf/issues/297
Deep sleep fixes
This change fixes extra 24 uA current consumption in deep sleep mode (https://esp32.com/viewtopic.php?f=2&t=1133).
Recent update to libphy/librtc caused another problem that WiFi related parts of RTC are no longer disabled by RTC sleep functions. This means that if WiFi is not disabled by the application before entering deep sleep, extra ~200uA of current would be consumed. This is fixed, and documentation for esp_deep_sleep and SNTP example are updated to mention that applications should take care of disabling WiFi and BT before going into the deep sleep mode.
See merge request !516
spi_flash: fix protection issues
This MR fixes the two spi_flash related issues:
- esp_intr_noniram_{disable,enable} not being protected by spi_flash_op_{lock,unlock} in single core mode. This caused a safety assert to be triggered in esp_intr_noniram_disable.
- spi_flash_unlock not being protected by spi_flash_guard_{start,end}. This caused a conflict between SPI0 and SPI1 controllers when accessing SPI flash, manifesting in cache data corruption and IllegalInstruction exceptions, for some flash chips.
See merge request !522
spi_flash_unlock was missing spi_flash_guard_start, which caused cache
to be enabled during unlock operation, causing hard-to-trace crashes
and cache data corruption.
MR !441 (7c155ab) has fixed issue with esp_intr_noniram_{disable,enable}
calls not being properly protected by spi_flash_op_{lock,unlock}.
Unit test was added, but the unit test environment tests only dual-core
config. Similar issue was present in the code path for the single-core
config, where esp_intr_noniram_{disable,enable} calls were unprotected.
This change fixes the protection issue and updates the unit test to
run properly in single core config as well.
The issue with running unit tests for single core config will be
addressed in a separate MR.
In case WiFi/BT stack has been enabled but wasn’t disabled, some RTC
bits may be left enabled, causing increased current consumption.
This change returns some of the bits back to their default values.
Bootloader enables SAR ADC in test mode to get some entropy for the RNG.
The bits which control the ADC test mux were not disabled, which caused
extra ~24uA current to be drawn from VRTC, increasing deep sleep current
consumption. This change disables relevant test mode bits in
bootloader_random_disable.
1. add new APIs bt controller enable/disab/deinit
2. make bt controller work need to call two APIs of esp_bt_controller_init and enable
3. modify phy init to make mac reset once
1. add a macro in menuconfig for users to choose whether store phy calibration data into NVS or not.
2. rename some disable phy and rf APIs so that existing code which calls old APIS will fail to compile.
1. Add disable PHY and RF when WiFi and BT are both disabled(including call sniffer disable API).
2. Do not init PHY and RF when cpu start. Init PHY and RF when call Wifi or BT start APIs(including sniffer enable API).
3. Add a temporary lib: librtc_clk.a and will delete it when CPU frequency switching function is done.
4. Add an function to get OS tick rate.
5. Do not put the whole pp.a in iram0, only put lmac.o, ieee80211_misc.o, ets_time.o and wdev.o in iram0.
This connection error caused by iPhone, it think that TX data length must large than 27 when slave support EXTEND_DATA_LENGTH. But this should be allow. Besides, the problem cannot be found on higher version of Iphone7, apple seemed to have fixed it.
Actually maybe other BLE device have the same problem.
Docs: Document flash encryption disable steps, clean up flash encryption & secure boot docs
Generate clean up of flash encryption & secure boot docs
Including steps for disabling flash encryption (for people who accidentally enable it).
See merge request !500
phy_init: don’t rewrite valid calibration data
In the default PHY init routine, calibration data is loaded from NVS.
Most of the time the incremental changes to calibration will be fairly
small, so we don’t need to rewrite the existing calibration data stored
in the NVS.
Possible enhancement to be done in the future: expose a function in PHY
library to tell how big was the change in calibration data. If the
change was significant, then calibration data stored in NVS should be
updated.
See merge request !487
freertos: fix protection issue in freertos queue event list
When functions in queue.c calls listLIST_IS_EMPTY() to check queue event list, the queue list is
protected by queue mutex, on the other hand, when xTaskIncrementTick() modify the queue list, the
queue list is protected by xTaskQueueMutex, this may cause xTaskRemoveFromEventList operate on
the empty queue list and cause problem.
This change works around the problem by reducing the window where the race condition can happen.
See merge request !465
Also add steps to disable flash encryption, as some people seem to
accidentally enable it.
Explicitly mark the flash encryption and secure boot as "READ DOCS
FIRST" in menuconfig.
esp32: update wifi lib for some fixes and optimizations
1. Reduce the default static rx buffer size from 25 to 10
2. Adjust ampdu interrupt size to 3, namely, raise 1 interrupt per 3-mpdu
3. Make a copy for all received packets, including AMSDU/AMPDU/MPDU
4. Fix softap mis-forward issue
5. Fix pp q full issue
6. Fix sniffer copy wrong content issue
See merge request !491
When functions in queue.c calls listLIST_IS_EMPTY() to check queue event list, the queue list is
protected by queue mutex, on the other hand, when xTaskIncrementTick() modify the queue list, the
queue list is protected by xTaskQueueMutex, this may cause xTaskRemoveFromEventList operate on
the empty queue list and cause problem. This commit is to fix this bug.
may cause
1. Reduce the default static rx buffer size from 25 to 10
2. Adjust ampdu interrupt size to 3, namely, raise 1 interrupt per 3-mpdu
3. Make a copy for all received packets, including AMSDU/AMPDU/MPDU
4. Fix softap mis-forward issue
5. Fix pp q full issue
6. Fix sniffer copy wrong content issue
Fix interrupting task on other CPU that has lower prio than current task on current CPU
Fix for a very subtle bug introduced somewhere in december. This bug would cause a cross-core interrupt to only be sent if the activated task has a higher priority than the task currently running on *this* cpu, instead of on the other CPU.
See merge request !475
In the default PHY init routine, calibration data is loaded from NVS.
Most of the time the incremental changes to calibration will be fairly
small, so we don’t need to rewrite the existing calibration data stored
in the NVS.
Possible enhancement to be done in the future: expose a function in PHY
library to tell how big was the change in calibration data. If the
change was significant, then calibration data stored in NVS should be
updated.
esp32: Fixes watchdog problem when printing core dump to uart
1) Fixes watchdog problem when printing core dump to uart
2) Also fixes generation of core dumps when flash cache is disabled
See merge request !472
Current implementation has drive numbers and paths hardcoded to support
only one FATFS drive. Arduino has it's own SPI driver to allow
compatibility and flexibility. With the MR it is possible to have up to
```_VOLUMES``` drives connected (SPI, SDMMC and others) at the same
time and accessed through VFS
components/openssl: refactor openssl debugging and assert function
1. add openssl option at menuconfig
2. remove SSL_ERR to reduce complexity
3. add more functions about debugging and assert
According these, our coders and customers may use and debug the OpenSSL code easily.
See merge request !400
Use PART_FLAG_ENCRYPTED value in gen_esp32part.py
Currently paritions marked as encrypted by gen_esp32part.py are not
recognized as such and encrypted writes don't work.
This is part of espressif/esp-idf#253
Merges Pull Request #293https://github.com/espressif/esp-idf/pull/293
See merge request !470
Add missing variable initialisation to make SPI work for multiple CS
Ref https://github.com/espressif/esp-idf/pull/277
From PR: "I am not especially familiar with this platform or with esp-idf -- so review with care.
The spi-master driver would not work for me when the number of devices on a bus exceeded 1 (caused device hang). I believe this is because cur_cs is not properly set (anywhere), and yet is used. This is likely just not noticed because 0 is presumably the correct value when there's only 1 device (and I'm guessing multi-device setup is not tested as thoroughly).
Simply setting cur_cs to the correct slot value resolves the problem and multiple devices on a single bus behave correctly in my test environment."
Looks like a small oversight on my side.
See merge request !468
1. fix ampdu<->mpdu<->ampdu switch may cause rx slow issue by put mpdu into ampdu reorder queue
2. fix each ac first sending always fail issue by adding retry
Seems doing certain kinds of short reads while flash encryption is
enabled will return stale data. This fixes it, but is probably a
little heavy-handed performance wise.
Verify 0xE9 magic byte on first write, verify entire image before
switching.
Enable verification for secure boot signature (was using invalid ifdef
guard)
Currently paritions marked as encrypted by gen_esp32part.py are not
recognized as such and encrypted writes don't work.
This is part of espressif/esp-idf#253
lwip: optimize the dhcp client
1. modify the discover retry backoff time from (2,4,8,16,32,60,60)s to (500m,1,2,4,8,15,15)s.
2. add DHCP_DOES_ARP_CHECK to menuconfig for users to specify if do a ARP check on the offered address.
If enable, one more second will be taken.
See merge request !459
1. modify the discover retry backoff time from (2,4,8,16,32,60,60)s to (500m,1,2,4,8,15,15)s.
2. add DHCP_DOES_ARP_CHECK to menuconfig for users to specify if do a ARP check on the offered address.
If enable, one more second will be taken in obtaining IP address.
3. update wifi libs
Without this, it's possible for stale information to be read from
cache via mmap, even if the MMU table entry had been invalidated
prior to writing flash (if the same MMU table entry was re-used after
writing flash.)
docs: use custom roles to generate GitHub links
This change replaces direct links to GitHub master branch with
auto-generated links using docutils custom roles.
These auto-generated links point to the tree or blob for the git commit
ID (or tag) of the repository. This is needed to ensure that links don’t
become broken when files in master branch are moved around or deleted.
The following roles are introduced:
```
- :idf:`path` - points to directory inside ESP-IDF
- :idf_blob:`path` - points to file inside ESP-IDF
- :idf_raw:`path` - points to raw view of the file inside ESP-IDF
- :component:`path` - points to directory inside ESP-IDF components dir
- :component_blob:`path` - points to file inside ESP-IDF components dir
- :component_raw:`path` - points to raw view of the file inside ESP-IDF
components dir
- :example:`path` - points to directory inside ESP-IDF examples dir
- :example_blob:`path` - points to file inside ESP-IDF examples dir
- :example_raw:`path` - points to raw view of the file inside ESP-IDF
examples dir
```
A check is added to the CI build script, which searches RST files for
presence of hard-coded links (identified by tree/master, blob/master,
or raw/master part of the URL).
This check can be run manually: cd docs && make gh-linkcheck
Additionally, Sphinx linkcheck build type is used to create new CI test,
which check for broken links. This test has to be triggered explicitly,
because including it in normal build process (when the commit is not yet
deployed to Github) will not work. It can be triggered in a regular
fashion using a combination of cron and Curl, similar to stress tests.
See merge request !455
This change replaces direct links to GitHub master branch with
auto-generated links using docutils custom roles.
These auto-generated links point to the tree or blob for the git commit
ID (or tag) of the repository. This is needed to ensure that links don’t
become broken when files in master branch are moved around or deleted.
The following roles are introduced:
- :idf:`path` - points to directory inside ESP-IDF
- :idf_blob:`path` - points to file inside ESP-IDF
- :idf_raw:`path` - points to raw view of the file inside ESP-IDF
- :component:`path` - points to directory inside ESP-IDF components dir
- :component_blob:`path` - points to file inside ESP-IDF components dir
- :component_raw:`path` - points to raw view of the file inside ESP-IDF
components dir
- :example:`path` - points to directory inside ESP-IDF examples dir
- :example_blob:`path` - points to file inside ESP-IDF examples dir
- :example_raw:`path` - points to raw view of the file inside ESP-IDF
examples dir
A check is added to the CI build script, which searches RST files for
presence of hard-coded links (identified by tree/master, blob/master,
or raw/master part of the URL).
This check can be run manually: cd docs && make gh-linkcheck
Additionally, Sphinx linkcheck build type is used to create new CI test,
which check for broken links. This test has to be triggered explicitly,
because including it in normal build process (when the commit is not yet
deployed to Github) will not work. It can be triggered in a regular
fashion using a combination of cron and Curl, similar to stress tests.
1. clean up bluetooth storage log prints;
2. reduce maximum link key storage size
3. modify so that the link key information of the latest connected device is stored at first
Update esptool.py to v2.0-beta1
* Minor bug fixes, no major functionality changes from the esp-idf perspective.
* Now tracks master branch of esptool repo (finally!)
* Supports Python 3, although our other esp-idf Python tools don't yet support Python 3.
See merge request !396
If the DNS request is dispatched and performed very quickly,
then it can complete before tcpip_callback() actually returns,
in which case we'll destroy the actual err_t error value passed
in the message. Use a local variable for the tcpip_callback
error code so that can't happen.
Resolves#269https://github.com/espressif/esp-idf/pull/269
Move PHY options out of WiFi config, improve descriptions
- move PHY-related settings into new menu, make it dependent on WIFI_ENABLED || BT_ENABLED
- improve descriptions of Ethernet Kconfig options
See merge request !443
ESP32_PHY_MAX_TX_POWER option is only meaningful for WiFi, so previous
change made it depend on WIFI_ENABLED. However if WiFi is not enabled,
but BT is, this option becomes undefined which breaks phy_init_data
generation.
This change turns ESP32_PHY_MAX_TX_POWER into a hidden parameter, which
depends on PHY_ENABLED. New user-visible parameter,
ESP32_PHY_MAX_WIFI_TX_POWER is introduced which depends on WIFI_ENABLED
and is used as default value for ESP32_PHY_MAX_TX_POWER if WIFI_ENABLED
is set. Otherwise ESP32_PHY_MAX_WIFI_TX_POWER is set to 20.
newlib: fix register used for DPORT/RTC bug workaround
While there was no register at DR_REG_FRC_TIMER_BASE + 0x60, due to
peripheral address space wraparound this write actually affected one of
FRC2 registers, which is used by WiFi stack to implement legacy
ets_timer APIs.
This change uses FRC_TIMER_LOAD_REG(0) instead, which can be set to
known value safely.
See merge request !449
fixes for issues observed when using spi_flash
This MR fixes three unrelated issues:
- Race condition in spi_flash_enable_interrupts_caches_and_other_cpu
when operations on unpinned tasks are performed.
The issue is reported in https://github.com/espressif/esp-idf/pull/258
- esp_intr_noniram_disable doesn’t disable interrupts when compiled in
release mode. This issue manifested itself with an illegal instruction
exception when task WDT ISR was called at the time when flash was
disabled.
Fixes https://github.com/espressif/esp-idf/issues/263.
- Tick hooks on CPU1 were not called if CPU0 scheduler was disabled for
significant amount of time (which could happen when doing flash erase).
The issue manifested itself as “INT WDT timeout on core 1” error.
Fixes https://github.com/espressif/esp-idf/issues/219.
See merge request !441
While there was no register at DR_REG_FRC_TIMER_BASE + 0x60, due to
peripheral address space wraparound this write actually affected one of
FRC2 registers, which is used by WiFi stack to implement legacy
ets_timer APIs.
This change uses FRC_TIMER_LOAD_REG(0) instead, which can be set to
known value safely.
The block which dispatches ticks on CPU1 was a copy of the code block
for the normal path (CPU0). It used to check uxPendedTicks, with the
logic that uxPendedTicks can be 0 iff the scheduler is not suspended.
On CPU1 however, uxPendedTicks is not related to the state of the
scheduler (as uxPendedTicks is updated on CPU0). Due to this, if CPU0
scheduler was suspended, and uxPendedTicks happened to be nonzero,
tick hooks on CPU1 didn’t run, even though CPU1 scheduler was working.
This change removes the check for uxPendedTicks in CPU1 code path,
so that the tick hooks on CPU1 always get called (as for the CPU0 code
path).
Allow writes to encrypted partitions
There is a size alignment requirement but it is checked by
spi_flash_write_encrypted. However, this check flat-out bans encrypted
writes.
Original PR on Github: https://github.com/espressif/esp-idf/pull/249
See merge request !432
When compiling in release mode, compiler was choosing same register for
oldint and intmask variables, so INTENABLE was never modified.
This effectively broke disabling of non-IRAM interrupts during flash
operations, observed in the existing tests if task watchdog is enabled.
This change adds an extra constraint tells the compiler that output
operand should not be placed into the same register as an input one.
Add python script that parses list of unit test cases for CI from component test folder
Modify .gitlab-ci.yml to run this script as part of build unit tests stage
spi_flash_enable_interrupts_caches_and_other_cpu function used to enable
non-IRAM interrupts after giving up flash operation lock, which would
cause problems if another task was waiting on the lock to start a flash
operation. In fact, non-IRAM interrupts should be re-enabled before the
task scheduler is resumed. Otherwise non-pinned task can be moved to the
other CPU due to preemption, causing esp_intr_noniram_enable to be
called on the other CPU, causing an abort to be triggered.
Fixes the issue reported in
https://github.com/espressif/esp-idf/pull/258
Delete option to select core timer 2 as a FreeRTOS tick source
Core timer 2 is unusable for FreeRTOS ticks because it triggers a high-level interrupt. This MR deletes the option to select it.
Ref https://github.com/espressif/esp-idf/issues/234
See merge request !418
In some cases (when RTC register reads are performed from the APP CPU), a write to FRC_TIMER_INT_REG may be lost on the bus.
Writing to another DPORT register immediately before or after that works around the issue.
We write one dummy value to an address which doesn’t have any register associated with it.
Fixes https://github.com/espressif/arduino-esp32/issues/120
1. add openssl option at menuconfig
2. remove SSL_ERR to reduce complexity
3. add more functions about debugging and assert
According these, our coders and customers may use and debug the OpenSSL code easily.
One common pattern of using assert function looks as follows:
int ret = do_foo();
assert(ret == 0); // which reads as: “do_foo should never fail here, by design”
The problem with such code is that if ‘assert’ is removed by the preprocessor in release build,
variable ret is no longer used, and the compiler issues a warning about this.
Changing assert definition in the way done here make the variable used, from language syntax perspective.
Semantically, the variable is still unused at run time (as sizeof can be evaluated at compile time), so the compiler
can optimize things away if possible.
These functions are marked as inline and are called from functions which are in IRAM.
In release (-Os) builds, the compiler may decide not to inline these functions.
Placing these functions into IRAM explicitly works around this.
update wifi lib: fix some wifi lib bugs
1. net80211: fix get ap info error(a4614877)
2. tw9358: sta mac same with softap(ea38d32c)
3. tw9221: scan channel error when connected(183d469c)
See merge request !425
bootloader_random_disable: Restore all SARADC/I2S registers to defaults
Fix for issue with I2S0 not being usable after bootloader_random_enable()
See merge request !415
fixes for github issues
This MR includes commits from several Github PRs, as well some fixes for issues reported on Github and on the forum.
- compile PHY-related code only when WiFi is enabled
- fix macOS setup instructions
- fix some of the Sphinx warnings
- update docs index, improve structure of the readme-
- wifi: fix typos, rename ESP_ERR_WIFI_NOT_START to ESP_ERR_WIFI_NOT_STARTED
- sdmmc: fix explanation of flash voltage regulator configuration efuses
- sdmmc: change idx num of example
- fix i2c_get_period name
- fix esp_log_level_set function name in docs
See merge request !420
If using WIFI_INIT_CONFIG_DEFAULT, error message will point out lack
of WiFi. Otherwise linker errors on WiFi symbols should help give a
clue as to what is broken.
Piggy-backs on changes in !420, ref github #230#237
Fix panic register dump format
Fix misplaced a printf somewhere causing an enter to be printed after every register in the panic regdump instead of every 4th register.
Fixes https://github.com/espressif/esp-idf/issues/236
See merge request !419
esp32 core dump to flash
1. menuconfig option to select where to store core dump: flash, uart or disable
2. Saving of core dump to flash
3. Partition table definitions files with core dump partition
4. Python scripts to support core dump generation from GDB command line
See merge request !341
The following issues mentioned during MR!341 review were fixed:
1) Core dump test application description
2) Usage of CONFIG_ESP32_ENABLE_COREDUMP_TO_FLASH and CONFIG_ESP32_ENABLE_COREDUMP_TO_UART
3) FLASH_GUARD_START macro usage is fixed in flash API
4) Core dump module logging facility
5) cache util functions doc updated
6) interactive delay before print core dump to uart
7) core dump partion support in build system
component bt:Added the create attribute table method to the new API
GATT Server service table APIs.
Have already modify the style and other things as @jeroen suggestion in other MR(the MR have been closed)
See merge request !399
Deep sleep stub may call ets_update_cpu_frequency, which has been moved from ROM to IRAM.
Restore the ROM version in the linker script, call it ets_update_cpu_frequency_rom, use it in the deep sleep stub.
fix mbedtls unit tests, fix IDF_VER when building a project outside ESP-IDF tree
- mbedTLS test needs about 5% more time to run (in debug mode) when building with 5.2.0, compared to 4.8.5. Increase the timeout to let the test pass.
- when doing `git describe` in IDF_VER definition, `-C $(IDF_PATH)` is needed to get the version of ESP-IDF, and not the project being built (which may not even be in git)
See merge request !411
1) PS is fixed up to allow GDB backtrace to work properly
2) MR!341 discussion: in core dump module: esp_panicPutXXX was replaced by ets_printf.
3) MR!341 discussion: core dump flash magic number was changed.
4) MR!341 discussion: SPI flash access API was redesigned to allow flexible critical section management.
5) test app for core dump feature was added
6) fixed base64 file reading issues on Windows platform
7) now raw bin core file is deleted upon core loader failure by epscoredump.py
Complimentary changes:
1) Partition table definitions files with core dump partition
2) Special sub-type for core dump partition
3) Special version of spi_flash_xxx
4) espcoredump.py is script to get core dump from flash and print useful info
5) FreeRTOS API was extended to get tasks snapshots
Clean up WiFi & Bluetooth config options
* Splits "WiFi" configuration out from ESP32 configuration submenu to its own menu.
* Renames "BT" to "Bluetooth", enabling Bluetooth is now in this option not the ESP32 submenu.
* Also disables compiling/linking of BT stack if Bluetooth is disabled, saves some build time.
See merge request !397
update toolchain version, rebuild newlib
- This MR updates the toolchain version used in the ESP-IDF
- Compiler version check and warning is added to project.mk
- Newlib is rebuilt to include wcsftime function
- libstdc++ build uses correct newlib headers (so we won't get undefined reference to `__impure_ptr` anymore)
See merge request !387
esp32: fixs about auto-reconnect and ap ssid configuration
1. Remove auto-reconnect
2. Use strnlen instead strlen to calculate ssid len in wifi lib
See merge request !407
component/bt: check for registration status of callback function before using it
Add checking of NULL function pointers when calling bluetooth callbacks, especially before the callback functions are registered
See merge request !406
add wpa2 set id api and modify null data tx description
1. wpa2: add wpa2 set id api
2. low rate: modify null data tx description
See merge request !402
ethernet: support flow control
(1) Only fullduplex mode support flow ctrl .
(2) Fix reboot exception which caused by not-reset EMAC hardware (such as DMA) when reset CPU.
See merge request !392
component/bt: bug fix of lack of checking bluetooth stack status inside API functions
Add an API function for checking bluetooth stack status: whether it is uninitialized, initialized or enabled.
The function is intended to be used by users to check the bluetooth stack status, also, it is used inside bluetooth API functions to ensure the stack is in valid state.
See merge request !405
Place cross-core interrupt into IRAM, sanity check handler address passed into esp_intr_alloc
Cross-core interrupt handler was not marked with IRAM_ATTR.
The reason why this caused an exception is probably due to some tasks running at highest priority (these are not blocked by spi_flash_disable_caches_interrupts_and_other_cpu mechanism).
This change puts the interrupt handler into IRAM and adds a sanity check into `esp_intr_alloc`.
Reported on Github: https://github.com/espressif/esp-idf/issues/211
See merge request !404
build system: add IDF_VER environment variable and preprocessor define
This adds an `IDF_VER` preprocessor define which is obtained from `git describe`.
Looks like `v1.0-275-g0efaa4f` for non-release version or `v2.0` for a tagged (release) version.
See merge request !403
Add option to automatically set a watchpoint at the end of the swapped-in task
This should make stack overflows easier to debug because it triggers a debug exception as soon as the stack is overwritten, not later when a context switch happens. Marked as a FreeRTOS debug feature because it doesn't give a nice error message and uses up a watchpoint.
See merge request !389
Fix tcpip_adapter_set_hostname issue
The default hostname for each interface is "espressif", users can call this API to change each interface's hostname.
See merge request !284
examples/10_openssl_server: fixup SSL server with method of specific version
1. add method of any version supporting at OpenSSL and add API in header file
2. change OpenSSL server context method to be method of any version
Fixes http://esp32.com/viewtopic.php?f=14&t=696.
See merge request !369
Fix OpenOCD detection code
In the current master, detection of an attached OCD is broken. This fixes it.
I also snuck in two unrelated checks in intr_alloc which return from a function that is asserted earlier in the code. This makes the code behave better when they are called erroneously in a production build.
See merge request !377
bootloader: export ets_update_cpu_frequency
MR !363 added linking librtc into bootloader. At the same time, MR !373 removed ets_update_cpu_frequency from ROM exports ld script, and replaced it with a dual CPU aware version. Combining these two MRs caused linker error in bootloader due to the unresolved `ets_update_cpu_frequency`.
One option to fix this is to move the definition of ets_update_cpu_frequency into bootloader_support component. This does however look a bit odd because this function is not something that is specifically needed for bootloader support.
Another option is to export the ROM version of ets_update_cpu_frequency for the bootloader only. This means that when bootloader changes CPU frequency, it only updates the tick period variable for PRO CPU. This isn't an issue though, because app startup code still calls the dual CPU aware version of ets_update_cpu_frequency early on, before any non-trivial code can run on the APP cpu.
This MR uses the second approach. Looking forward, we may move this definition of ets_update_cpu_frequency into the rtc_clk component, which will be used both by the bootloader and the app, and placing ets_update_cpu_frequency there would be logical.
See merge request !384
SDMMC peripheral driver, SD protocol driver, FATFS library, VFS integration
This MR contains:
- SDMMC host peripheral driver
- SD protocol driver in sdmmc component (can be extended to support MMC/eMMC and SPI based hosts)
- ChaN's FATFS library v0.12b
- VFS integration
- FAT access via VFS is thread-safe (unless same file is read/written/unlinked/renamed from different tasks)
- Support for POSIX directory-related functions in VFS (and in vfs_fatfs.c)
- unit test for the above
- Example
- API documentation
Will be done in other MRs:
- Support for spi_flash IO driver for FatFs
- SPI host driver and support for SPI mode commands in sdmmc component
- MMC/eMMC support in sdmmc component
- Support for slightly higher 53/26.6MHz clocks (currently I'm using 20MHz for DS and 40MHz for HS, instead of 25MHz/50MHz per standard), and arbitrary low clocks (e.g. 4MHz).
See merge request !353
C++ support
This change adds necessary support for compiling C++ programs:
- linking against libstdc++
- implementation of static initialization guards using FreeRTOS primitives: since we don't have condition variables at our disposal, and we don't want to allocate a synchronization primitive for every guard variable generated by the compiler, we imitate condition variables using a combination of a mutex, counting semaphore, and a counter (based on [Microsoft Research paper](https://www.microsoft.com/en-us/research/wp-content/uploads/2004/12/ImplementingCVs.pdf), albeit because we don't need *arbitrary* code to use these CVs, implementation gets simpler).
Note that libstdc++ also contains an implementation of `__cxa_guard_{acquire,release,abort}` functions. These implementations come from an `#ifndef GXX_THREADS` branch, i.e. are not aware of multthreading. There are three ways of replacing these libstdc++ functions with our implementation:
1. Move our code into gcc. Pros: cleanest solution. Cons: Such changes are unlikely to be merged by any upstream, so we end up maintaining our own forks of {gcc,crosstool-ng}.
2. Use library as it is built by crosstool, use `ar` to delete one object file (`guards.o`), add this library to ESP-IDF. Pros: easy to implement. Cons: libstdc++ is a 15MB binary 😯
3. Keep using libstdc++ from crosstool, force our implementation to be linked using a `-u` linker flag. Pros: no impact on repo size, easy to implement. Cons: somewhat less clean than 1 (and about as hacky as 2).
For the reasons mentioned, option (3) looks like the best tradeoff.
Ref. TW6702
See merge request !364
Enable bootloader entropy source for RNG
Enables an entropy source when bootloader starts up, which both seeds the RNG for use before WiFi/BT stack is enabled and provides an adequate RNG for secure boot & flash encryption key generation.
A prerequisite was enabling 80MHz operation, so the CPU is now set to 80MHz as soon as second stage bootloader starts running.
See merge request !363
add menuconfig option to enable SO_RCVBUF
This option is required by Arduino and enables netconn connection to be queried for amount of data available in the rx buffer.
See merge request !372
esp32: ets_update_cpu_frequency should set tick scale for both CPUs
ets_update_cpu_frequency ROM function updates g_ticks_per_us, which is has two copies, one for each CPU.
The APP CPU copy of g_ticks_per_us never got updated, resulting in shorter delays produced by ets_delay_us on the APP CPU.
This MR replaces ROM ets_update_cpu_frequency with a copy in IRAM which updates scaling factors on both of the CPUs.
So now we get expected delays (in microseconds):
```
ets_delay_us core=0 expected=50000 actual=50014
ets_delay_us core=1 expected=50000 actual=50015
vTaskDelay core=0 expected=50000 actual=49428
vTaskDelay core=1 expected=50000 actual=50000
```
Reported on the forum: http://esp32.com/viewtopic.php?f=2&t=713#p3722
See merge request !373
SPI master driver
This merge requests adds an SPI Master driver. This driver is (of course) multithread capable, has device abstraction, has command queueing, DMA support and all other sorts of nice things you'd expect from a SPI driver.
See merge request !332
modify bootloader dram start address, swap app bss and data segments
Modify bootloader dram_seg from address 0x3ffc0000 to 0x3fff0000, len from 0x20000 to 0x10000.
Also put app .data before .bss, to reduce the chance .data collides with ROM bootloader stack.
See merge request !375
This change reduces chances that a large .bss segment will push .data all the way into
0x3ffe1320 — 0x3ffe5320 range where the bootloader stack is, creating a problem when
bootloader will be loading application into memory.
With this change, .data would need to be at least 200k big to cause problems.
Modify bootloader dram_seg from address 0x3ffc0000 to 0x3fff0000, len from
0x20000 to 0x10000. Please be notified that this is just a workaround for
fixing app data overwrite bootloader data issue!
1. add fading functions.
2. clear up ledc.c and ledc.h
3. update api doc.
4. add ledc example
5. edit ledc.rst and add readme for example code.
6. add s_ prefix for static global values.
7. add mutex for fade functions
8. minor changes according to the comments.
1. add method of any version supporting at OpenSSL and add API in header file
2. change OpenSSL server context method to be method of any version
Fixes http://esp32.com/viewtopic.php?f=14&t=696.
1. Update wifi lib which contains ampdu and other optimizations
2. Add throughput code debug code
3. Other misc modification about throughput optimization
2. update example comments and other minor changes
3. rename API: i2c_cmd_link_create/i2c_cmd_link_delete (+4 squashed commits)
Squashed commits:
[2e0ac3e] 1. coding style: add one space after condition key words.
2. modify i2c.h, use gpio_num_t instead of int, improve comments of return values
3. add i2c index in index.rst
4. add readme for i2c example
[4991d92] update i2c.doc
[88b672e] driver: i2c
1. add mux and spin lock to run in a thread-safe way.
2. modify example code
[4eb15fe] driver: i2c code
1. add i2c master code
2. add i2c slave code
3. add i2c example code
4. add DRAM_ATTR for I2C array
bugfix: uart event mismatch
Fix bug of uart frame error and parity error interrupt mismatch in driver code, which will cause the corresponding interrupt can not be cleared correctly, and will finally cause a interrupt watch dog.
See merge request !335
GPIO driver: add per-pin interrupt handlers
1. add ISR handler apis so that users of different layers can hook their own isr handler on different GPIO.
Audio project has different software layers, they need different gpio isr handler for layer instead of processing all GPIO interrupts in one handler.
If this kind of calling a handler from isr is not proper, please kindly point out.
2. add gpio example code.
3. update gpio doc.
See merge request !345
1. add ISR handler apis so that users of different layers can hook their own isr handler on different GPIO.
Audio project has different software layers, they need different gpio isr handler for layer instead of processing all GPIO interrupts in one handler.
If this kind of calling a handler from isr is not proper, please kindly point out.
2. add gpio example code.
3. improve gpio.rst
4. add readme for gpio example
Squashed commits:
[278e50f] update: GPIO
1. coding style, add a space between conditional or loop keyword and an opening paren.
2. modify some return value and doc
3. use printf in example code
Squashed commits:
[efb23bb] minor change of comment
freertos: fix dual core issue
This commit try to fix dual issue tw9313 raised by QA
1. Put per-core data into critical session or interrupt disabled/enabled session
2. Idle task may have problem when it terminate the task in both core
See merge request !333
1. The transmitting mode of the packets from LWIP to MAC is changed from synchronous to asynchronous.
2. The receive buf mode : support pointer mode and copy mode.
3. Add get phy status func used to config mac register.
1. Fix bug of uart frame error and parity error interrupt mismatch in driver code, which will cause the corresponding interrupt can not be cleared correctly, and will finally cause a interrupt watch dog.
2. Add gpio pull-up for rx pin and cts pin.
This commit fixes:
1. xTaskGetCurrentTaskHandle may return wrong TCB when current task switch to a different core
2. Idle task may have problem when it terminate the task in both core
Minor fixes from various sources
- Fix memory debugging code. Noticed by Tuan.
- intr_enable/disable should be in IRAM. Noticed by rojer
- Still old timer code in examples in doxygen comments. Noticed on the forum by jumjum123
- Timer example was broken. Noticed on the forum by jumjum123
See merge request !325
ULP: add new instructions, fix bugs, add tests
This adds peripheral register read and write instructions, an instruction to wake the SoC from deep sleep, and some tests.
Also fixes two bugs: ANDI instruction definition, and running the ULP when in deep sleep mode.
See merge request !317
Fix exception handler to jump to correct vector instead of crashing to the double exception vector.
One-character fix... basically, this caused the exception handler to crash into the double-exception handler instead of nicy panic'ing.
See merge request !323
Secure boot: Option for app & partition table signing to happen outside build system
Allows for a remote signing server, private signing key does not need to be on the build system.
See merge request !320
Allow gw to be null
Github Pull Request 163: https://github.com/espressif/esp-idf/pull/163
Allow interfaces to be configured without a default gateway, for
local-only communication.
In case of the AP interface, if gw is not set, do not offer it.
See merge request !312
1. change all gatt cb function to 3 args and function type. add gattc_if/gatts_if as second argument
2. delete gatt_if of "gatt cb param"
3. separate conn_id and gatt_if from conn_id
4. change the demo code as the gatt changed
1. add sigma-delta code and example.
2. add gpio output signal in io matrix.
Squashed commits:
[a25e7d4] minor changes for doc
[6a03a1e] minor changes on comments and doc.
[97dd9e4] Add doc.
update index.rst
change example index
Starting the ULP using SENS_SAR_START_FORCE_REG doesn’t disable clock gating of RTC fast clock.
When SoC goes into deep sleep mode, RTC fast clock gets gated, so ULP can no longer run.
Instead, it has to be started using the timer (RTC_CNTL_ULP_CP_SLP_TIMER_EN bit).
When ULP is enabled by the timer, clock also gets enabled.
This change allows setting pin configuration for EXT1 wakeup depending on the state of RTC_PERIPH power domain:
- if peripherals are enabled (due to another wakeup mode, or due to esp_deep_sleep_pd_config call), we can keep internal pullups/pulldowns enabled
- if peripherals are disabled, pullups and pulldowns need to be disabled as well
Also add comments about the purpose of registers being configured.
This adds a workaround for a bug that following deep sleep wakeup, ISO (bus isolation) signal may be set for RTC fast memory.
We set FORCE_NOISO bit in RTC_CNTL_PWC_REG until we find out what is causing ISO signal to be set.
When ESP32 wakes up from deep sleep, flash is accessed an approximately 900us after power on.
Some flash chips need more time to become ready. This change adds a menuconfig option to add
some delay to the default deep sleep wake stub.
Fixes https://github.com/espressif/esp-idf/issues/117
This adds the following APIs to enable various wakeup sources:
- esp_deep_sleep_enable_timer_wakeup
- esp_deep_sleep_enable_ulp_wakeup
- esp_deep_sleep_enable_ext0_wakeup
- esp_deep_sleep_enable_ext1_wakeup
And an API to start deep sleep:
- esp_deep_sleep_start
1. TW8657, WIFI send the whole packet to smartconfig;
2. modify API annotation of smartconfig and sniffer;
3. export smartconfig APIs to programming guide;
lwip: fix lwip dual core issue
Call xSemaphoreGiveFromISR instead xSemaphoreGive when the calling context is in critical section.
See merge request !314
Restore ability to alloc IRAM, and more.
- Fix mem regions so allocating IRAM works again
- Optimize allocator slightly, uses 4 less bytes per malloc now
- Allow querying free heap memory space per memory type
See merge request !301
Bugfix/btdm bluedroid
Cleanup all the warnings。
Fix GATT CLIENT cannot receive notfiy/indicate from GATT SERVER bug.
Originally, bluetooth have its own master branch(feature/btdm_bluedroid), all the bluetooth sub branch will merge to feature/btdm_bluedroid firstly. If feature/btdm_bluedroid is ready, it will request merge to master. But as Ivan/JG/Jack's requires, all the bluetooth bugfix or feature will request merge to master ASAP.
This MR contains "cleanup warning " and "some bug fix", after, every merge request only contain one thing.
See merge request !286
1. enable will malloc, but disable don't free resolving list, so fix it
2. In disable procedure, it will alloc alarm to hash_map, and all the alarm hash_map will be free in deinit. So this need not be fixed currently.
build system: Linker scripts or binary libraries should trigger a re-link
Add binary libraries and linker scripts to the list of dependencies for the ELF file.
Fixes TW7816.
See merge request !307
Allow interfaces to be configured without a default gateway, for
local-only communication.
In case of the AP interface, if gw is not set, do not offer it.
1. fix the exception of deinit/disable
2. debug mem leak of deinit, fix some memleak, but still something wrong.
3. debug men leak of disable.
4. add bluedroid memory debug
“Full” printf uses more stack space than “nano” printf, and more space than available in the idle task.
This caused stack overflow in TLS delete test. Replacing printf with ets_printf.
add supported stress test to CI
add supported stress test to CI:
stress test requires long time to execute. They will only be executed when variable NIGHT_BUILD=YES. Therefore we'll use gitlab-API trigger to execute stress test cases.
See merge request !220
drivers: remove file paths from log statements
Function name and error string are usually sufficient to find the place which has triggered an error.
`__FILE__` macro generates a string which has absolute file name (with our build system), which add many long strings to the program binary.
Also change log tags to lower case to match style used elsewhere.
Fixes https://github.com/espressif/esp-idf/issues/126
See merge request !282
Flash encryption support
Flash encryption support in build system, tooling
To come in future MR:
* On-device key generation on first boot (for production devices), need to finalise testing of bootloader entropy seeding.
* spi_flash_encrypted_write to support non-32-byte block writes (at least optionally.)
* I think a lot of the bootloader_support component can possibly be rolled into "spiflash" and other components, to use a common API.
See merge request !240
Add dynamic interrupt allocation mechanism
This adds:
- Dynamic allocation of interrupts. Pass it the features of the interrupt you want, it'll set you up with an int.
- Shared interrupts. Enables multiple peripheral drivers to use the same interrupt.
- Marking what interrupts are fully executable from IRAM; if an int isn't marked like that it will get disabled once flash cache gets disabled.
Also:
- Modifies driver to be in line with these changes
See merge request !254
Fail CI build on warnings
This allows developers to add CFLAGS for -Wno-error=XXX while developing, but before code passes the CI build then it must be warning-free.
See merge request !279
newlib: add "full" formatting support
This change adds support for 64-bit formats and C99 features to newlib printf/scanf functions. This support is enabled by default in menuconfig, but can be switched off to reduce code size.
Also adds missing functions such as fmod and fmodf.
- Fixes https://github.com/espressif/esp-idf/issues/52
- Fixes https://github.com/espressif/esp-idf/issues/83
See merge request !274
- add two versions of libc: libc.a and libc_nano.a. First one has full C99 formatting support, second one uses “nano” formatting functions available in ROM.
- fix linker error for fmod, fmodf, atof, atoff
- update tests
UART console selection
This change adds a set of menuconfig options to set custom UART#, baud rate, and pins, for console output.
Ref. TW8146
Also includes the following changes:
- `uart_tx_wait_idle`: fix issue with last character not transmitted. ROM function `uart_tx_wait_idle` may have a bug which causes the function to return before the final character is fully transmitted. This replaces `uart_tx_wait_idle` declaration with a static inline definition which fixes the issue. Also replaces the use of `uart_tx_flush` with `uart_tx_wait_idle` in `esp_restart`, to remove garbage in console output on restart.
- `rtc_printf` is temporary replaced with a no-op, pending a new release of librtc.a. Current release assumes that UART0 is used for output,
and switches UART0 baud rate while doing frequency changes and printing some log output. This doesn’t work if a different UART is used for output.
- disable boot watchdog only after starting the main task. Boot watchdogs were disabled very early in startup code. It was possible to introduce an infinite loop anywhere in the many functions called from startup code, and this would not be detected by interrupt watchdog and task watchdog. This change postpones disabling of boot watchdogs to the point when the scheduler is running. Also replaces register expressed using integer address with a name. This change is not directly related to the previous ones, but was found while debugging UART selection features.
See merge request !288
Removal of spurious newline character in debug statement
There was a debug statement in the code that included an additional newline character that wasn't needed.
From github PR: https://github.com/espressif/esp-idf/pull/124
See merge request !291
On Xtensa windowed ABI backtrace is easy to do, and it's immensely
useful for debugging, so - do it by default.
We try to be careful and not deref bogus pointers while walking the
frames.
Example output (from debugging espressif/esp-idf#133):
Backtrace: 0x1:0x3ffc51e0 0x400e9dfa:0x3ffc5210 0x400e9ebc:0x3ffc5230 0x400ec487:0x3ffc5260
With just addr2line utility from binutils, this already pinpoints the
location of the crash.
Boot watchdogs were disabled very early in startup code. It was possible to introduce an infinite loop anywhere in the many functions called from startup code, and this would not be detected by interrupt watchdog and task watchdog. This change postpones disabling of boot watchdogs to the point when the scheduler is running. Also replaces register expressed using integer address with a name.
- ROM function uart_tx_wait_idle may have a bug which causes the function to return before the final character is fully transmitted.
This replaces uart_tx_wait_idle declaration with a static inline definition which fixes the issue.
- Also replaces the use of uart_tx_flush with uart_tx_wait_idle in esp_restart, to remove garbage in console output on restart.
- rtc_printf is temporary replaced with a no-op, pending a new release of librtc.a. Current release assumes that UART0 is used for output,
and switches UART0 baud rate while doing frequency changes and printing some log output. This doesn’t work if a different UART is used for output.
This change adds a set of menuconfig options to set custom UART#, baud rate, and pins, for console output.
Setting happens in bootloader startup code for PRO CPU, and in application startup code for APP CPU.
Ref. TW8146
feature(rtc_module):add rtc module
1. add rtc io control API (pull,output and input)
2. add touch pad API (touch pad read and interrupt)
3. add adc1 API (the max width is 12 Bits and support attenuation)
4. add hall sensor API (support hall sensor read )
5. add dac API (the width is 8 Bits)
bugfix(gpio):gpio32 and gpio33 can not output and input
the gpio32 and gpio33 is initialize by librtc.a,and gpio_config not initialize the gpio as
digital gpio.they can not output and input,when users use gpio32 or gpio33.And there are some problems
about others driver ,when they use gpio32 or gpio33 as matrix.
Function name and error string are usually sufficient to find the place which has triggered an error. __FILE__ macro generates a string which has absolute file name (with our build system), so there is a lot of long strings present in the program because of that.
Fixes https://github.com/espressif/esp-idf/issues/126
Small debugging fixes
Invoke panic handler when a stack overflow has been detected; unhandled interrupt handler now prints interrupt/cpu number for easier pinning down of source.
See merge request !277
Gdbstub: Fix bug, small cleanup
Tianzhongxing found a small bug preventing gdbstub to work in certain cases. This fixes it, as well as including some minor cleanups.
See merge request !260
Initial support for generation of ULP coprocessor code
This adds basic support for writing ULP coprocessor programs using an assembly-like syntax, with integer labels and branches to labels.
See merge request !261
* App access functions are all flash encryption-aware
* Documentation for flash encryption
* Partition read/write is flash aware
* New encrypted write function
Feature/btdm bluedroid
This branch contain the bluedroid host code.
Currently, Only GAP/GATT SERVER/GATT CLIENT release to users.
Actually, the content of the codes is further more than GAP/GATT and etc.
In this release version, users only need to concern about the APIs which are in "api/include/".
Now, suggestions in comment have been resolved are following:
1. The APIs use callback function. Ivan , Jeroen and me have discussed it. Currently the code will not be changed.
2. The APIs use OPEN/CLOSE. I have ask Ivan, besides bluedroid do this, we will keep the name.
3. Coding style. I have run format.sh to handle the style. And some spell error have been fixed.
4. APIs doxygen. I have clean the warning by doxygen. But bt.rst is still need to be completed.
5. Other comment without resolved face to face that I have to add response in the comment and fix them in the code
6. Fix some incorrect things. See the git log for details.
This 1st version of bluedroid release still have lots of things to do. But it can be done after this merge.
1. Compelete the BLUFI(Bluetooth config wifi connection) documents, security, application protocol and other.
2. Add SPP-LIKE profile.
3. Do more examples codes to cover most of the APIs.
4. Test and fix bug.
Another thing：
1. Do the document of APIs.(xml->bt.rst->html)
(I will do this before merge as Ivan's suggestion)
This is already done. Besides, the union type in doxygen have something error. Ivan will fix it.
See merge request !239
bugfix/init_factory_bin: fix inconsistency between bootloader and OTA code
init_factory_bin: 2nd bootloader use a wrong logic select factory image to boot,and some bug in OTA code
See merge request !266
1. fix tw8911 sleep in scan leads to auth frame malloc fail.
2. fix tw8913 pm state transfer wrong leads to wdt.
3. make some comments for modem sleep and wpa2 enterprise.
4. removd duplicated debug option ESP_THREAD_SAFE_DEBUG
esp32: update wifi lib to fix tw8868
In AP bridge mode, the length of the forwarded data is wrong, it's 26Btyes longer, thus cuase
AP can't forward the data of which length is 1460. This modification is to make the
data length right.
See merge request !262
In AP bridge mode, the length of the forwarded data is wrong, it's 26Btyes longer, thus cuase
AP can't forward the data of which length is more than 1460. This modification is to make the
data length right.
esp32: fix tw8851 some phy version cause wifi connect fail
Update phy version to 258 to fix tw8851
When upgrade the phy version, the RF calibration version is not change, but the calibration data format is changed and the wrong calibration data causes wifi connection failure. The solution is to make RF calibration data and phy version the same version.
See merge request !258
1. update phy to version 258 to fix wifi upgrade cause wifi connect fail issue
2. update fix_printf.sh
3. fb5a2b07 - default set ps type to WIFI_PS_NONE
Add fota ops api
add ota core function implement
1. esp_ota_begin: init ota partition need to be update, output ota handle,every partition need ota should be init firstly
2. esp_ota_write: write image data to update partition, will record wrote size automatically
3. esp_ota_end: verify image after ota ended
4. esp_ota_set_boot_partition: set next boot partition
5. esp_ota_get_boot_partition: get current running partition
See merge request !256
Bugfix mbedtls sha384 clone()
mbedtls_sha512_clone() on a SHA-384 hash caused incorrect digest
Also adds additional mbedtls unit tests into the unit tests project (including one for this bug).
See merge request !252
lwip: fix socket memory leak issue
1. Add socket memory leak debug counter
2. Fix TCP PCB leak issue
Currently ESP32 support maximum 16 TCP PCBs and all TCP PCB are allocated from heap memory. In some scenario, we may
have memory leak issue, for example, the application already created 16 TCP PCB, then it close 5 of them, because the TCP
state machine, the LWIP core may not free all the 5 TCP PCB immediately, maybe some is in TIME_WAIT status, some is in
FIN_WAIT_1 etc. Then the application try to malloc 17th TCP PCB (the application think they just create 12 because they already
close 5), memp_malloc() will return true because the heap is not out of memory, but actually we got 17 TCP PCB. When the
scenario repeat again and again (in our Audio application, it repeat more than 10000 times), more and more TCP PCB will be
created in the system, each TCP PCB require 200B, then memory leak happen (In Audio application, I saw more than 26 TCP PCB
are created, and 10*200=2K memory are leaked).
See merge request !223
SHA acceleration integrated to mbedTLS incl. TLS sessions
Uses hardware SHA acceleration where available, fails over to software where not available.
Ref TW7112
See merge request !232
spi_flash_erase_range: Allow for 32KB blocks not 64KB blocks
SPI flash hardware sends 52h command, which is a 32KB erase.
There is a matching bug in the ROM SPIEraseArea code, unless
flashchip->block_size is modified first.
See merge request !249
ledc: fix reported error when div_param == 256
Whenever bit_num and freq_hz are such that div_param == 256, the code would flag that as an error.
In fact, value 256 of div_param was a valid one (HW requires that div_param >= 1.0, when interpreted as a Q10.8 fixed point value).
Changed the if statements a bit to make the logic clearer, and added more descriptive error messages.
Also added missing error for the unimplemented case of low speed mode.
Reported in https://github.com/igrr/esp32-cam-demo/issues/2
See merge request !247
driver: PCNT
1. add PCNT module in periph_ctrl.c/.h
2. add description of PCNT status in pcnt_struct.h
3. add PCNT driver code
4. add PCNT example code.
See merge request !229
uart: use same argument names in get/set functions
This one is pretty trivial: rename arguments so that same name is used for get and set functions.
https://github.com/espressif/esp-idf/issues/105
See merge request !248
system_* APIs cleanup
This changeset is mostly about cleaning up `system_*` APIs and moving them from libcore. It has dragged a few more changes along, however.
- `system_deep_sleep` deprecated, new name is `esp_deep_sleep`
- `system_efuse_read_mac` deprecated, new name is `esp_efuse_read_mac`
- `system_read/write_rtc_mem` removed (reason: we use linker to place code/data into RTC memory now)
- `system_get_sdk_version` deprecated. Returns "master" for now. Support for compile-time and runtime version detection will be done in a separate MR.
- `system_get_time` and variations have been deprecated. `gettimeofday` should be used instead.
- `system_restart` deprecated, new name is `esp_restart`. Rewritten code to work correctly from any of the cores.
- `system_restore` deprecated, `esp_wifi_restore` should be used instead.
- `system_get_rst_info` removed (it wasn't in a header file)
- RTC library has been updated to latest version
- Logging output from `libfoo.a` goes through `foo_printf` function now, where `foo ` is any of the library names. For libraries other than rtc and phy, this is a temporary measure, until we finish switching to esp_log library and clean up all uses of printf/ets_printf.
- ESP-IDF build will fail if any of the libraries have printf/ets_printf reference.
- Added `esp_random` function which gets values from HW RNG. I have added code which makes sure the value is not polled too often (allows at least 16 APB cycles). Also added a header file for HW RNG (just one register).
- Moved random number generation functions used by wpa library into wpa_supplicant component.
See merge request !234
SPI flash hardware sends 52h command, which is a 32KB erase.
There is a matching bug in the ROM SPIEraseArea code, unless
flashchip->block_size is modified first.
Whenever bit_num and freq_hz are such that div_param == 256, the code would flag that as an error.
In fact, value 256 of div_param was a valid one (HW requires that div_param >= 1.0, when interpreted as a Q10.8 fixed point value).
Changed the if statements a bit to make the logic clearer, and added more descriptive error messages.
Also added missing error for the unimplemented case of low speed mode.
UART driver: Fix crash in ISR due to "UART" static array moved to flash
Ref: http://esp32.com/viewtopic.php?f=13&t=546&sid=76ff371ae2b259441a2cf355e96d74b9#p2275
This is a really subtle bug, gcc noticed the UART array elements are read-only so
implicitly moved the elements to .rodata as if it was const. However
this array is accessed from the UART ISR, so has to be in IRAM or DRAM.
See merge request !245
Refs:
http://esp32.com/viewtopic.php?f=13&t=550http://esp32.com/viewtopic.php?f=13&t=551
rmt.c should include stdlib.h for malloc, esp_bignum,c &
https_request_main.c for abort().
FreeRTOSConfig.h is only including stdlib if
CONFIG_FREERTOS_ASSERT_ON_UNTESTED_FUNCTION is set. However, it is
included for abort() so needs to be included whenever
CONFIG_FREERTOS_ASSERT_FAIL_ABORT is set.
This change includes unconditionally in FreeRTOSConfig.h. This is to
avoid this kind of bug where compiler errors are dependent on config. I
suggest we don't change this to be more selective until we have 'make
randomconfig' style tests in CI.
Integrate unit tests into build system
This MR moves unit tests from esp-idf-tests repository into 'test' subdirectories of respective components.
Tests are run using a runner app in tools/unit-test-app.
This needs a bit of cleanup:
1. remove extra newlines added to makefiles,
2. re-format unit tests code which has tabs
3. write a document on using this test app
4. maybe some refactoring in project.mk
I think 1&2&4 need to be done in this MR, while 3 may be done in a follow-up one.
See merge request !221
Includes a tweak to make Static_task_t equal size to TCB_t when using
MPU_WRAPPERS . Matches tskSTATIC_AND_DYNAMIC_ALLOCATION_POSSIBLE macro
in tasks.c. This isn't actually a bug (if static task allocation is off,
there is no use for Static_task_t), but it allows us to make consistent
compile-time checks that Static_task_t == TCB_t.
Without this change, building FreeRTOS with static allocation enabled succeeds, but trying to create a queue from a static buffer causes an assert because the size of static and dynamic queues differ.
1. change gap btc args to union to decrease the dram occupied by btc args
2. actually use individual args for every action is the best way(decrease the dram occupy), but for writing code easily and the style, use union
3. gatt server/client should do the same work
esp32: fix random pkt cause esp32 watchdog
This change fixes the ESP32 watchdog issue. When the MPDU of AMPDU is longer than 1600B,
esp32 will check whether the last 4B is DEADBEEF, if it's not DEADBEEF, it will assert
and the assert will cause esp32 watchdog. The solution is to init the last 4B to DEADBEEF
when malloc new ebuf for the packet longer than 1600B.
See merge request !233
SHA hardware allows each of SHA1, SHA256, SHA384&SHA512 to calculate digests
concurrently.
Currently incompatible with AES acceleration due to a hardware reset problem.
Ref TW7111.
rename nvs host test folder, modify .gitlab-ci.yml
remove unit-test-app build
re-format unit test files
remove extra newlines in project.mk
some refactoring for unit test part in project.mk
add build files of unit-test-app in gitignore
add README.md for unit test app
correct headings in README.md
remove files and make minor tweaks in unit test app
update .gitlab-ci.yml to use unit test app
delete unused lines in component_wrapper.mk
delete periph_i2s.h and lcd test
add text floating point in components/esp32/test/Kconfig
correct idf test build paths in .gitlab-ci.yml
This change fixes the ESP32 watchdog issue. When the MPDU of AMPDU is longer than 1600B,
esp32 will check whether the last 4B is DEADBEEF, if it's not DEADBEEF, it will assert
and the assert will cause esp32 watchdog. The solution is to init the last 4B to DEADBEEF
when malloc new ebuf for the packet longer than 1600B.
LWIP will drop the oldest package at the arp packet cache queue and return "ERR_OK"
We change it that ARP level will drop the current packet and return "ERR_MEM" to tell user that you should send the packet again latter.
hwcryto bignum support for RSA operations
Supporting RSA with hardware bignum directives.
Configurable via menuconfig to enable/disable, and to choose between busywaiting and interrupt driven completion.
May still be some performance tweaks possible.
TW7111
See merge request !92
Removes memory barriers for better performance, thanks Ivan for pointing
this out.
Manually unrolling the loop further seemed like diminishing returns.
