1. add sigma-delta code and example.
2. add gpio output signal in io matrix.
Squashed commits:
[a25e7d4] minor changes for doc
[6a03a1e] minor changes on comments and doc.
[97dd9e4] Add doc.
update index.rst
change example index
This change allows setting pin configuration for EXT1 wakeup depending on the state of RTC_PERIPH power domain:
- if peripherals are enabled (due to another wakeup mode, or due to esp_deep_sleep_pd_config call), we can keep internal pullups/pulldowns enabled
- if peripherals are disabled, pullups and pulldowns need to be disabled as well
Also add comments about the purpose of registers being configured.
This adds the following APIs to enable various wakeup sources:
- esp_deep_sleep_enable_timer_wakeup
- esp_deep_sleep_enable_ulp_wakeup
- esp_deep_sleep_enable_ext0_wakeup
- esp_deep_sleep_enable_ext1_wakeup
And an API to start deep sleep:
- esp_deep_sleep_start
1. TW8657, WIFI send the whole packet to smartconfig;
2. modify API annotation of smartconfig and sniffer;
3. export smartconfig APIs to programming guide;
Flash encryption support
Flash encryption support in build system, tooling
To come in future MR:
* On-device key generation on first boot (for production devices), need to finalise testing of bootloader entropy seeding.
* spi_flash_encrypted_write to support non-32-byte block writes (at least optionally.)
* I think a lot of the bootloader_support component can possibly be rolled into "spiflash" and other components, to use a common API.
See merge request !240
Add dynamic interrupt allocation mechanism
This adds:
- Dynamic allocation of interrupts. Pass it the features of the interrupt you want, it'll set you up with an int.
- Shared interrupts. Enables multiple peripheral drivers to use the same interrupt.
- Marking what interrupts are fully executable from IRAM; if an int isn't marked like that it will get disabled once flash cache gets disabled.
Also:
- Modifies driver to be in line with these changes
See merge request !254
- ROM function uart_tx_wait_idle may have a bug which causes the function to return before the final character is fully transmitted.
This replaces uart_tx_wait_idle declaration with a static inline definition which fixes the issue.
- Also replaces the use of uart_tx_flush with uart_tx_wait_idle in esp_restart, to remove garbage in console output on restart.
- rtc_printf is temporary replaced with a no-op, pending a new release of librtc.a. Current release assumes that UART0 is used for output,
and switches UART0 baud rate while doing frequency changes and printing some log output. This doesn’t work if a different UART is used for output.
feature(rtc_module):add rtc module
1. add rtc io control API (pull,output and input)
2. add touch pad API (touch pad read and interrupt)
3. add adc1 API (the max width is 12 Bits and support attenuation)
4. add hall sensor API (support hall sensor read )
5. add dac API (the width is 8 Bits)
bugfix(gpio):gpio32 and gpio33 can not output and input
the gpio32 and gpio33 is initialize by librtc.a,and gpio_config not initialize the gpio as
digital gpio.they can not output and input,when users use gpio32 or gpio33.And there are some problems
about others driver ,when they use gpio32 or gpio33 as matrix.
* App access functions are all flash encryption-aware
* Documentation for flash encryption
* Partition read/write is flash aware
* New encrypted write function
Feature/btdm bluedroid
This branch contain the bluedroid host code.
Currently, Only GAP/GATT SERVER/GATT CLIENT release to users.
Actually, the content of the codes is further more than GAP/GATT and etc.
In this release version, users only need to concern about the APIs which are in "api/include/".
Now, suggestions in comment have been resolved are following:
1. The APIs use callback function. Ivan , Jeroen and me have discussed it. Currently the code will not be changed.
2. The APIs use OPEN/CLOSE. I have ask Ivan, besides bluedroid do this, we will keep the name.
3. Coding style. I have run format.sh to handle the style. And some spell error have been fixed.
4. APIs doxygen. I have clean the warning by doxygen. But bt.rst is still need to be completed.
5. Other comment without resolved face to face that I have to add response in the comment and fix them in the code
6. Fix some incorrect things. See the git log for details.
This 1st version of bluedroid release still have lots of things to do. But it can be done after this merge.
1. Compelete the BLUFI(Bluetooth config wifi connection) documents, security, application protocol and other.
2. Add SPP-LIKE profile.
3. Do more examples codes to cover most of the APIs.
4. Test and fix bug.
Another thing：
1. Do the document of APIs.(xml->bt.rst->html)
(I will do this before merge as Ivan's suggestion)
This is already done. Besides, the union type in doxygen have something error. Ivan will fix it.
See merge request !239
1. fix tw8911 sleep in scan leads to auth frame malloc fail.
2. fix tw8913 pm state transfer wrong leads to wdt.
3. make some comments for modem sleep and wpa2 enterprise.
4. removd duplicated debug option ESP_THREAD_SAFE_DEBUG
Bugfix mbedtls sha384 clone()
mbedtls_sha512_clone() on a SHA-384 hash caused incorrect digest
Also adds additional mbedtls unit tests into the unit tests project (including one for this bug).
See merge request !252
SHA acceleration integrated to mbedTLS incl. TLS sessions
Uses hardware SHA acceleration where available, fails over to software where not available.
Ref TW7112
See merge request !232
spi_flash_erase_range: Allow for 32KB blocks not 64KB blocks
SPI flash hardware sends 52h command, which is a 32KB erase.
There is a matching bug in the ROM SPIEraseArea code, unless
flashchip->block_size is modified first.
See merge request !249
driver: PCNT
1. add PCNT module in periph_ctrl.c/.h
2. add description of PCNT status in pcnt_struct.h
3. add PCNT driver code
4. add PCNT example code.
See merge request !229
SPI flash hardware sends 52h command, which is a 32KB erase.
There is a matching bug in the ROM SPIEraseArea code, unless
flashchip->block_size is modified first.
SHA hardware allows each of SHA1, SHA256, SHA384&SHA512 to calculate digests
concurrently.
Currently incompatible with AES acceleration due to a hardware reset problem.
Ref TW7111.
hwcryto bignum support for RSA operations
Supporting RSA with hardware bignum directives.
Configurable via menuconfig to enable/disable, and to choose between busywaiting and interrupt driven completion.
May still be some performance tweaks possible.
TW7111
See merge request !92
esp32/make: add detailed return error code for wifi APIs
1. Add detailed return error code for wifi APIs
2. Add description about error code in esp_wifi.h
3. Modify esp_wifi_reg_rxcb to esp_wifi_internal_reg_rxcb
4. Modify esp_wifi_set_sta_ip to esp_wifi_internal_set_sta_ip
5. Mark system_init as deprecated API
See merge request !187
1. Add detailed return error code for wifi APIs
2. Add description about error code in esp_wifi.h
3. Modify esp_wifi_reg_rxcb to esp_wifi_internal_reg_rxcb
4. Modify esp_wifi_set_sta_ip to esp_wifi_internal_set_sta_ip
5. Mark system_init as deprecated API
Deep sleep: Any source named rtc_wake_stub* is linked as RTC wake stub code
Also move esp_deepsleep.h documentation out to docs/deep-sleep-stub.rst
See merge request !142
Add cross-core int to accelerate task being awoken from another CPU.
This adds a per-CPU interrupt that can be used to poke the CPU to go do something. In this case all that is implemented is a request to yield the current task, used in case a CPU unblocks a task that runs on another CPU. This gets rid of the limitation that inter-CPU communication using queues, muxes etc can take up to a FreeRTOS tick to happen.
Specs!
Sending an in in a queue of length 1 (essentially a semaphore) as quickly as possible (just a small delay in the sender, to make sure the receiver task gets swapped out) for 10 seconds. Number indicates the amount of ints transferred
Old code:
CPU0->CPU0: 42986
CPU0->CPU1,: 2999
New code:
CPU0->CPU0: 42868
CPU0->CPU1: 62073
See merge request !155
- spaces->tabs in tasks.c
- update vfs_uart.c to use per-UART locks
- add license to vfs_uart.c
- allocate separate streams for stdout, stdin, stderr, so that they can be independently reassigned
- fix build system test failure
Feature/wdts
This adds two watchdogs to esp-idf:
- An interrupt watchdog. Kicks in if the FreeRTOS timer interupt on either the PRO_CPU or (when configured) the APP CPU isn't called for a configurable time. Panics, displaying which CPU caused the problem and the registers that may lead to the offending code.
- A task watchdog. A task has to feed it every once in a while. If not, it will print the name of the offending tasks, as well as the tasks currently running on both CPUs, and optionally panic.
Also adds a panic reason to the panic call, as well as fixes the panic code a bit.
See merge request !148
The customers need to get information about AP that associated with ESP32 station,
these information includes RSSI, channel number etc, so add this new API
1. Modify sta to station in comments
2. Modify esp_wifi_get_ap_num to esp_wifi_scan_get_ap_num
3. Modify esp_wifi_get_ap_list to esp_wifi_scan_get_ap_records
1. Modify comments for esp_wifi_internal_tx
2. Fix delay time error in esp32_tx_flow_ctrl which is found in code review,
modify _wait_delay init value from 0 to 1
Some small fixes
- Kill unused uxReturn in task.c, https://github.com/espressif/esp-idf/issues/48
- Line end conversion in gpio.c
- Move heap_alloc_caps.h so components can also use it
See merge request !135
esp32: Bootloader wake deep sleep stub
App can contain a stub program resident in RTC fast memory. Bootloader
will load the stub on initial boot. If the device wakes from deep sleep,
the stub is run immediately (before any other data is loaded, etc.)
To implement a custom wake stub, implement a function in your program:
```
void RTC_IRAM_ATTR esp_wake_deep_sleep(void)
{
esp_default_wake_deep_sleep();
// other wake logic
}
```
... and it will replace the default implementation.
See merge request !78
We reserve 4KB Slow RTC memory to save RF calibation result and BT NVS data.
If not all these Slow RTC momory Blocks are used, we will open the other parts.
App can contain a stub program resident in RTC fast memory. Bootloader
will load the stub on initial boot. If the device wakes from deep sleep,
the stub is run immediately (before any other data is loaded, etc.)
To implement a custom wake stub, implement a function in your program:
```
void RTC_IRAM_ATTR esp_wake_deep_sleep(void)
{
esp_default_wake_deep_sleep();
// other wake logic
}
```
... and it will replace the default implementation.
While this may reduce esp_wifi.h file readability for people who don't have a "go to definition" function in their editors, this is needed to decouple esp_wifi and esp_event headers, and possibly other headers which may use wifi types in the future.
This change separates definitions in esp_event.h and functions in event.c into several parts:
- event structure definitions (esp_event.h)
- default implementations of event handlers (event_default_handlers.c)
- default implementation of event loop (event_loop.c, esp_event_loop.h)
Purpose of this change is to allow applications choose their own poison:
- full control of event loop at the expense of more bootstrap code
- pre-defined event task firing event callbacks, but less code in app_main.c
This change removes implicit WiFi/BT initialization from startup code.
"main" task is started once essential part of startup code is complete.
This task calls application-provided "int main(void)" function, which can call WiFi/BT init functions if necessary.
* master: (57 commits)
components/lwip: fix grammar
components/lwip: make SO_REUSE configurable via menuconfig
bootloader: remove trailing newlines from log messages
components/freertos: override per-task __cleanup handler to close stdin, stdout, stderr
components/esp32: move peripheral symbols to separate ld script
components/log: regroup macros for better readability
gitlab-ci: allow running tests for branches, triggered via API
components/log: fix timestamp calculation
components/log: set default runtime log level to ESP_LOG_VERBOSE
components/log: fix error when using ESP_LOGx from C++ code
components/log: fix bugs, add options to override log level for files, components, and bootloader
fix ledc and spi typo
remove prefix and postfix
Enable SO_REUSEADDR in LWIP
freertos: fix memory debug macro issue Define configENABLE_MEMORY_DEBUG according to CONFIG_ENABLE_MEMORY_DEBUG
peripheral structure headers: move volatile keyword from members to typedef
Adding -fstrict-volatile-bitfields to the CFLAGS/CXXFLAGS. Without this, gcc tries to access bitfields using the smallest possible methods (eg l8i to grab an 8-bit field from a 32-bit). Our hardware does not like that. This flag tells gcc that if a bitfield is volatile, it should always use the type the field is defined at (uint32_t in our case) to size its access to the field. This fixes accessing the hardware through the xxx_struct.h headers.
add peripheral module struct headers
build system docs: Add note about no spaces in component names
Docs: Add note about unusual submodule messages when cloning on Windows
...
# Conflicts:
# components/esp32/cpu_start.c
# components/esp32/include/soc/cpu.h
Add logging library
Logging library, intended to be used across other components.
Uses design similar to Android NDK logging APIs and allows for both compile time and run time filters, similar to logcat.
Also includes cleanup of cpu_startup.c — i was changing some logging output in this file so decided to re-format it and reduce code duplication.
Ref TW6703
See merge request !68
Move CPU region protection setup into soc/cpu.h
change tabs to spaces
remove unused extern declarations
use RTC_WDTCONFIG0 instead of numeric address (still need to fix BB reg)
Note that with WiFi stack enabled, system_init will reset frequency to 240MHz.
To make this setting useful, esp32-wifi-libs submodule needs to be updated.
Dual core compatible spi flash APIs
Implementation of spi flash APIs which work in dual core mode.
This also includes other changes:
- fixes to FreeRTOS tasks.c made by Jeroen and me — these were originally made to fix issues with high priority tasks seen in WiFi stack, but were required to get stuff in ipc.c working as well
- initial base idea with two high-priority tasks was separated into a separate API — esp_ipc.h. That API allows one to run a function on the other CPU from a high-priority task. Because we don't have preemption across CPUs, this is currently not very fast: it requires on average half a tick until the second CPU switches to the high priority task. Currently that API can be either blocking, or non-blocking with queue length of 1. I haven't yet found a use case for arbitrary sized queue of IPC requests. Anyone who needs that can trivially add that later by replacing a binary semaphore with a generic queue.
With these changes i can run application with WiFi stack and NVS on both cores.
See merge request !25
