1. When dual core cpu run access DPORT register, must do protection.
2. If access DPORT register, must use DPORT_REG_READ/DPORT_REG_WRITE and DPORT_XXX register operation macro.
I2S driver - fixed support for 24 and 32-bits, fixed tx/rx at the same time
- Modify sample can test with 24, 32-bits audio
- Add i2s sample README
- simply i2s_push function
- change sample rates, bits per sample, channel on fly
See merge request !483
Add support 24, 32 bits
@jxmao optimize i2s_zero_buffer
@jxmao correct config support slave mode
@jxmao correct setup pin support tx/rx at the same time
Enhance pin power
@jxmao add dynamic change number of channels
remove nvs_init
remove start log and enhance power pin setup
using enum for i2s_channel and i2s_bits_per_sample, return ESP_ERR_INVALID_ARG when check params
validate i2s_bits_per_sample and channel
check tx & rx buffer before fill zero
remove checking channel as @jxmao suggest
limit dma buffer
modify i2s pin back to gpio mux before configure gpio matrix, resolve github issue #512
Add support 24, 32 bits
reduce push function
Modify sample can test with 24, 32-bits
Add i2s sample README
Fixed i2s_set_clk got reset sometime
can changes bit-wide while running
Fix sample rate calculation for DAC mode from @jeroen
modify example can change bits per sample every 5 seconds
cleanup
add comment for bytes_per_sample
update as @angus suggestions
Add i2s_set_clk api
I2S driver bug fixed as following log:
@jxmao optimize i2s_zero_buffer
@jxmao correct config support slave mode
@jxmao correct setup pin support tx/rx at the same time
Enhance pin power
@jxmao add dynamic change number of channels
remove nvs_init
remove start log and enhance power pin setup
using enum for i2s_channel and i2s_bits_per_sample, return ESP_ERR_INVALID_ARG when check params
validate i2s_bits_per_sample and channel
check tx & rx buffer before fill zero
remove checking channel as @jxmao suggest
limit dma buffer
modify i2s pin back to gpio mux before configure gpio matrix, resolve github issue #512
limit dma buffer to 4092
change gpio_matrix_*_check to inline function, remove some comments and rename test_i2s function to setup_triangle_sine_waves
for change commit title
sdmmc: handle card removal when CD is not used
When SD card is removed during transaction, SDMMC peripheral can report
a range of errors, such as timeouts, CRC errors, start/end bit errors.
Under normal conditions (card is inserted), SDMMC peripheral also generates
command done or data done interrupts. When the card is removed, such
interrupts may not be always generated.
This change fixes handling of timeout interrupts and SBE interrupts.
It also adds a one second timeout into the event processing loop. This
timeout allows applications to recover in cases when the SDMMC peripheral
doesn’t generate command/data done event on card removal.
Fixes TW11592.
See merge request !678
SPI transfer length is bits, not bytes, so the error should indicate bits. Also, there are separate lengths for rx and
tx (confusingly named rxlength and length... if rxlength is 0, length is used). The code checks the tx length for the
rx, so it never validates rxlength.
Originally contributed as part of #511https://github.com/espressif/esp-idf/pull/511
When SD card is removed during transaction, SDMMC peripheral can report
a range of errors, such as timeouts, CRC errors, start/end bit errors.
Under normal conditions (card is inserted), SDMMC peripheral also generates
command done or data done interrupts. When the card is removed, such
interrupts may not be always generated.
This change fixes handling of timeout interrupts and SBE interrupts.
It also adds a one second timeout into the event processing loop. This
timeout allows applications to recover in cases when the SDMMC peripheral
doesn’t generate command/data done event on card removal.
To enable tx empty interrupt each time the tx ringbuffer get filled, so that tx function will not block if tx data length is larger than tx ringbuffer size.
Reported from customer of Audio team.
modify touch pad read function
The touch pad read function taks too much time within spin lock waiting for the "done bit". (about 7.6ms as we tested)
So we try to use a mutex on the touch read function and any other functions might change the "done bit".
See merge request !543
This issue is reported from https://github.com/espressif/esp-idf/issues/304.
We found that when we operate the hw command registers in I2C struct, sometimes the behaviour would be different in DEBUG/RELEASE optimisation level:
The code looks like this:
I2C[i2c_num]->command[p_i2c->cmd_idx].byte_num -= 0;
In DEBUG configuration:
I2C[i2c_num]->command[p_i2c->cmd_idx].byte_num -= 0;
400f3ab0: 3388 l32i.n a8, a3, 12
400f3ab2: 14c882 addi a8, a8, 20
400f3ab5: a08840 addx4 a8, a8, a4
400f3ab8: 0020c0 memw
400f3abb: 2898 l32i.n a9, a8, 8
400f3abd: 0020c0 memw
400f3ac0: 28b8 l32i.n a11, a8, 8
400f3ac2: 74a090 extui a10, a9, 0, 8
400f3ac5: 00af92 movi a9, 0xffffff00
400f3ac8: 109b90 and a9, a11, a9
400f3acb: 2099a0 or a9, a9, a10
400f3ace: 0020c0 memw
400f3ad1: 2899 s32i.n a9, a8, 8
In RELEASE configuration:
I2C[i2c_num]->command[p_i2c->cmd_idx].byte_num -= 0;
400f2ba2: 580572 l8ui a7, a5, 88
400f2ba5: 747070 extui a7, a7, 0, 8
400f2ba8: 0020c0 memw
400f2bab: 584572 s8i a7, a5, 88
Looks like the compiler will make it a 8bit operation after optimisation.
But the register value changes from 0x901 to 0x101.
After this 8-bit optimisation, the 11th bit changed from 1 to zero, which caused this error.
We are still trying to find out why that happens, because there might be some risk when operating the register struct.
This is a workaround to avoid "-=" operation on I2C register struct fields.
1. Add low speed channels for LEDC module.
2. Improve fade object allocate mechanism.
3. Improve ledc example, add 2 low speed channels in example.
4. Remove debug code
5. Improve the register bit field name of slow clock.
The touch pad read function taks too much time within spin lock waiting for the "done bit". (about 7.6ms as we tested)
So we try to use a mutex on the touch read function and any other functions might change the "done bit".
1. add fading functions.
2. clear up ledc.c and ledc.h
3. update api doc.
4. add ledc example
5. edit ledc.rst and add readme for example code.
6. add s_ prefix for static global values.
7. add mutex for fade functions
8. minor changes according to the comments.
2. update example comments and other minor changes
3. rename API: i2c_cmd_link_create/i2c_cmd_link_delete (+4 squashed commits)
Squashed commits:
[2e0ac3e] 1. coding style: add one space after condition key words.
2. modify i2c.h, use gpio_num_t instead of int, improve comments of return values
3. add i2c index in index.rst
4. add readme for i2c example
[4991d92] update i2c.doc
[88b672e] driver: i2c
1. add mux and spin lock to run in a thread-safe way.
2. modify example code
[4eb15fe] driver: i2c code
1. add i2c master code
2. add i2c slave code
3. add i2c example code
4. add DRAM_ATTR for I2C array
bugfix: uart event mismatch
Fix bug of uart frame error and parity error interrupt mismatch in driver code, which will cause the corresponding interrupt can not be cleared correctly, and will finally cause a interrupt watch dog.
See merge request !335
GPIO driver: add per-pin interrupt handlers
1. add ISR handler apis so that users of different layers can hook their own isr handler on different GPIO.
Audio project has different software layers, they need different gpio isr handler for layer instead of processing all GPIO interrupts in one handler.
If this kind of calling a handler from isr is not proper, please kindly point out.
2. add gpio example code.
3. update gpio doc.
See merge request !345
1. add ISR handler apis so that users of different layers can hook their own isr handler on different GPIO.
Audio project has different software layers, they need different gpio isr handler for layer instead of processing all GPIO interrupts in one handler.
If this kind of calling a handler from isr is not proper, please kindly point out.
2. add gpio example code.
3. improve gpio.rst
4. add readme for gpio example
Squashed commits:
[278e50f] update: GPIO
1. coding style, add a space between conditional or loop keyword and an opening paren.
2. modify some return value and doc
3. use printf in example code
Squashed commits:
[efb23bb] minor change of comment
1. Fix bug of uart frame error and parity error interrupt mismatch in driver code, which will cause the corresponding interrupt can not be cleared correctly, and will finally cause a interrupt watch dog.
2. Add gpio pull-up for rx pin and cts pin.
1. add sigma-delta code and example.
2. add gpio output signal in io matrix.
Squashed commits:
[a25e7d4] minor changes for doc
[6a03a1e] minor changes on comments and doc.
[97dd9e4] Add doc.
update index.rst
change example index
This adds the following APIs to enable various wakeup sources:
- esp_deep_sleep_enable_timer_wakeup
- esp_deep_sleep_enable_ulp_wakeup
- esp_deep_sleep_enable_ext0_wakeup
- esp_deep_sleep_enable_ext1_wakeup
And an API to start deep sleep:
- esp_deep_sleep_start
drivers: remove file paths from log statements
Function name and error string are usually sufficient to find the place which has triggered an error.
`__FILE__` macro generates a string which has absolute file name (with our build system), which add many long strings to the program binary.
Also change log tags to lower case to match style used elsewhere.
Fixes https://github.com/espressif/esp-idf/issues/126
See merge request !282
Removal of spurious newline character in debug statement
There was a debug statement in the code that included an additional newline character that wasn't needed.
From github PR: https://github.com/espressif/esp-idf/pull/124
See merge request !291
feature(rtc_module):add rtc module
1. add rtc io control API (pull,output and input)
2. add touch pad API (touch pad read and interrupt)
3. add adc1 API (the max width is 12 Bits and support attenuation)
4. add hall sensor API (support hall sensor read )
5. add dac API (the width is 8 Bits)
bugfix(gpio):gpio32 and gpio33 can not output and input
the gpio32 and gpio33 is initialize by librtc.a,and gpio_config not initialize the gpio as
digital gpio.they can not output and input,when users use gpio32 or gpio33.And there are some problems
about others driver ,when they use gpio32 or gpio33 as matrix.
Function name and error string are usually sufficient to find the place which has triggered an error. __FILE__ macro generates a string which has absolute file name (with our build system), so there is a lot of long strings present in the program because of that.
Fixes https://github.com/espressif/esp-idf/issues/126
ledc: fix reported error when div_param == 256
Whenever bit_num and freq_hz are such that div_param == 256, the code would flag that as an error.
In fact, value 256 of div_param was a valid one (HW requires that div_param >= 1.0, when interpreted as a Q10.8 fixed point value).
Changed the if statements a bit to make the logic clearer, and added more descriptive error messages.
Also added missing error for the unimplemented case of low speed mode.
Reported in https://github.com/igrr/esp32-cam-demo/issues/2
See merge request !247
driver: PCNT
1. add PCNT module in periph_ctrl.c/.h
2. add description of PCNT status in pcnt_struct.h
3. add PCNT driver code
4. add PCNT example code.
See merge request !229
Whenever bit_num and freq_hz are such that div_param == 256, the code would flag that as an error.
In fact, value 256 of div_param was a valid one (HW requires that div_param >= 1.0, when interpreted as a Q10.8 fixed point value).
Changed the if statements a bit to make the logic clearer, and added more descriptive error messages.
Also added missing error for the unimplemented case of low speed mode.
UART driver: Fix crash in ISR due to "UART" static array moved to flash
Ref: http://esp32.com/viewtopic.php?f=13&t=546&sid=76ff371ae2b259441a2cf355e96d74b9#p2275
This is a really subtle bug, gcc noticed the UART array elements are read-only so
implicitly moved the elements to .rodata as if it was const. However
this array is accessed from the UART ISR, so has to be in IRAM or DRAM.
See merge request !245
Refs:
http://esp32.com/viewtopic.php?f=13&t=550http://esp32.com/viewtopic.php?f=13&t=551
rmt.c should include stdlib.h for malloc, esp_bignum,c &
https_request_main.c for abort().
FreeRTOSConfig.h is only including stdlib if
CONFIG_FREERTOS_ASSERT_ON_UNTESTED_FUNCTION is set. However, it is
included for abort() so needs to be included whenever
CONFIG_FREERTOS_ASSERT_FAIL_ABORT is set.
This change includes unconditionally in FreeRTOSConfig.h. This is to
avoid this kind of bug where compiler errors are dependent on config. I
suggest we don't change this to be more selective until we have 'make
randomconfig' style tests in CI.
New makefile component_wrapper.mk allows some variables to be set
before component.mk is evaluated. This properly fixes problems with
sdkconfig being hard to access in all phases of the build.
Including component_common.mk is no longer necessary and will print a
deprecation warning for components which use it.
1. remove "\n" when calling ESP_LOGX APIs.
2. modify uart_event_t for uart rx data.
3. use MICRO for uart inverse value
4. add uart_tx_data_t for internal tx function.
1. Set XXX_TAG static, remove extern XXX_TAG in uart.h/ledc.h/gpio.h
2. I removed uart_set/get_print_port() functions, these functions are not well tested, I removed them for now.
3. Modify some function names for uart_read/write_bytes
4. Modify uart_write_bytes and uart_write_bytes_with_break.
1. fix bug in ringbuffer.c:
When return an dummy item, free_ptr might exceed rd_ptr, so the write_ptr would overwrite rd_ptr in this case.
2. Delete UART tx task in buffer mode. UART ISR will copy the data from tx buffer to fifo.
1. Add a ring buffer for UART TX.
If the buffer size is set to zero, driver will not use a buffer. But we need a task to send data from buffer to fifo. I tried directly copy data in ISR, but the code looked too long for ISR.
2. Modify the format in uart.h
1. Use esp_log API for LEDC and GPIO code.
2. Modify some API return value.
3. Add ledc_set_pin() for LEDC
4. Modify typo in uart.h
Questions: In uart driver ISR handler, I used xxxFromISR , like xSemaphoreGiveFromISR, do those FromISR functions need to be put in IRAM?
1. configure LEDC timer saparately
2. add peripher_crtl.c/.h
To enable the peripheral modules, we have to set/clear the control register in dport_reg.h.
These bits are disabled by default and they are all in a same register, so we need to add a lock on that.
3. add include esp_err.h in gpio.h
