AVRCP connection binds to A2DP in current implementation, despite the two profiles are\
independent according to specification. AVRCP connection is not necessary to set-up \
if A2DP connection fails to establish
In opening state of AVDTP connection, if SDP client fails to get valid A2DP service record\
from peer SDP server, then do not initiate AVDTP connection request
In pevious implementation, A2DP sink will register an A2DP source Stream End Point(SEP) although the SEP is not\
supposed to be used. Now remove the unused SEP for source so that only one role of A2DP can be supported at one
time. Service record in local SDP server only includes at most one service for A2DP sink role or source
1. In original driver, the stack size for emac driver task "emacT" is only 2048 Bytes, which also can not be changed by user.
2. Each time when invoking "emac_start" function, it will reset emac registers, the driver should reconfig some important registers again.
Currently CI test environment is complicated, usually includes NIC, AP.
These devices are not used for a lot test cases. Therefore we split the
test environment, remove unnecessary devices. Then it will be easier to
create CI runners.
As the bluedroid original implmentation of BR/EDR and BLE dual mode about discovery mode,
when set discovery mode for BR/EDR, it will stop ble advertising.
Reference to https://github.com/espressif/esp-idf/issues/2306
The following commit rewrites the ESP-MESH docs. This commit includes
new diagrams and a structure approach to the mesh docs. Some mesh api references
have also been modified.
This commit does the following
- Add power management lock to CAN driver so that APB frequency does not change
whilst CAN driver is in use
- Fix incorrect flag in can_transmit()
- Refactor can_driver_install() and can_driver_uninstall() so that critical sections
are shorter
- Fix CAN gpio configuration bug on RX pin. Closes#2302
- Add docs about multiple ID configuration and fix example links
Problem:
The new API esp_bt_mem_release() that was added freed BTDM data to heap from esp_bt_controller_mem_release().
Now with the BT memory optimization commit ee787085f9,
the BTDM data is optimized and reduced to only 32 bytes which is not sufficient amount to be added to heap.
So, using the API leads to assert saying that the region is too small.
Solution:
Modify heap_caps_add_region_with_caps to return ESP_ERR_INVALID_SIZE in case the range is too small to create a new heap.
Do not assert if return value is ESP_ERR_INVALID_SIZE
This also fixes using API esp_bt_controller_mem_release() with ESP_BT_MODE_BTDM
Signed-off-by: Hrishikesh Dhayagude <hrishi@espressif.com>
Some APs transmit AMPDU and MPDU by turns. Moreover, the sequence
numbers of AMPDU and MPDU are out of order, e.g. MPDU(1253) -
AMPDU(1251, 1252) - MPDU(1254) - AMPDU(1255, 1256). In order to
receive both AMPDU and MPDU in order, MPDU must be reordered with
AMPDU.
1. New tests for SD card on slot 0. Currently frequency for 4-bit mode
has to be reduced in the test.
2. Change pin for CD/WP tests, re-enable CD tests.
Works for 3.3V eMMC in 4 line mode.
Not implemented:
- DDR mode for SD cards (UHS-I) also need voltage to be switched to 1.8V.
- 8-line DDR mode for eMMC to be implemented later.
It is possible to utilize some of the routines related to otadata
partition validation, after firmware image is downloaded to RAM. Hence
these routines should be part of app cpu cache, so that they do not
get overwritten by firmware.
Signed-off-by: Mahavir Jain <mahavir@espressif.com>
Allows OTA updates to be secured via signature checks, without requiring the overhead or complexity
of a full secure boot implementation.
Uses same signing mechanisms (build system and/or espsecure.py as Secure Boot).
Requires:
* [ ] More testing
* [ ] Documentation
res was declared as “bool” so expression
((count == 0) ? A2D_SET_ONE_BIT : A2D_SET_MULTL_BIT)
always evaluated to “true”, and was implicitly converted to
A2D_SET_ONE_BIT.
Avoids growing the result of hardware bignum operations
(particularly for multiplication)
Fixes bugs where some Elliptic Curve operations fail or corrupt memory,
as they assume length of the number is never greater than the number of
non-zero limbs.
Includes some general refactoring to standardize terminology.
Closes https://github.com/espressif/esp-idf/issues/1556
Fixes TW12984
Adds test cases for both these issues.
1. after memory release MR merged, due to the get acl number condition is not completed, it will cause get acl number value incorrect
2. It may cause set Security Mode (BR/EDR) enable failed
1. change static emac-dma memory to dynamic
2. add esp_eth_deinit
3. modify ethernet example
4. add testcase for ethernet deinit function
5. GPIO0 could not output the 50MHz clock to PHY, so remove this configuration
1. new APIs: esp_mesh_get_subnet_nodes_num() and esp_mesh_get_subnet_nodes_list().
2. fix hard to find the parent during connect.
3. disable Wi-Fi channel switch function.
4. fix a typo of MESH_EVENT_NO_PARENT_FOUND.
esp_reset_reason_init would check for reset reason hint, and
unconditionally set RTC_RESET_CAUSE_REG (which is also
RTC_ENTRY_ADDR_REG) to hint value 0, i.e. 0x80000000. However the ROM
code treats this value as valid deep sleep wake stub entry point, and
tries to jump to it.
Clear RTC_RESET_CAUSE_REG only if it contained a valid reset reason
hint, and simply set the register value to 0 when doing so. Also add
a check to esp_get_deep_sleep_wake_stub function that deep sleep wake
stub entry address must be in IRAM.
Reported in https://esp32.com/viewtopic.php?f=13&t=6919.
Fix following WiFi bugs:
1. Shouldn't scan when connect
2. Check beacon length in modem sleep
3. Fix the bug that AP may deauth wrong station when inactivity timer expires
4. Fix the bug that WiFi assert the system when receiving empty MCS in association response frame
Multiple modules register their callback BTA_GATTS_AppRegister().
If any of the callbacks do not free the allocated pointer in
BTA_GATTS_CONF_EVT event, then this can result in memory leak.
So, free the pointer after the callback function is called and remove
the calls to free in the callback functions as it is now not required
Signed-off-by: Hrishikesh Dhayagude <hrishi@espressif.com>
This is just a quick glance at all the header files exposed to the
users from cleanup point of view.
Signed-off-by: Hrishikesh Dhayagude <hrishi@espressif.com>
We have fixed a bug in test script. Before that, we didn't do strict check when generate the mesh tree, which makes the test pass.
Temp disable these cases, to let CI pass before bug fixed.
When 32k XTAL was selected as clock source, if the first calibration
attempt failed, the code would fall back to 150kHz internal clock.
Calibration with the internal clock will always succeed.
Therefore `wait` would always be either 0 or 1. Based on this, some
code in this routine can be eliminated.
Marking a page full does not skip it from page selection process and the
same page might get returned if there is no other page with more unused
entries. Added a check for the same while storing blobs.
Fixes: https://github.com/espressif/esp-idf/issues/2313
Previous APIs used to set CPU frequency used CPU frequencies listed in
rtc_cpu_freq_t enumeration. This was problematic for two reasons.
First, supporting many possible frequency values obtained by dividing
XTAL frequency was hard, as every value would have to be listed in
the enumeration. Since different base XTAL frequencies are supported,
this further complicated things, since not all of these divided
frequencies would be valid for any given XTAL frequency. Second,
having to deal with enumeration values often involved switch
statements to convert between enumeration and MHz values, handle
PLL/XTAL frequencies separately, etc.
This change introduces rtc_cpu_freq_config_t structure, which contains
CPU frequency (in MHz) and information on how this frequency has to
be generated: clock source (XTAL/PLL), source frequency, clock
divider value. More fields can be added to this structure in the
future. This structure simplifies many parts of the code, since both
frequency value and frequency generation settings can be accessed in
any place in code without the need for conversions.
Additionally, this change adds setting of REF_TICK dividers to support
frequencies lower then XTAL with DFS.
`esp_http_client_write` API puts a constraint on the maximum length of the data that can be
written, which is equal to client handle buffer size, but the data to be sent can be more
than that, so in this case, this API has to be called multiple times.
In `esp_http_client_open` API, the return value of `transport_write` API, used to send HTTP
request, is not checked, and in rare cases, data written will be less than expected which will
cause a problem. So there are fixes for these minor issues in this MR.
Calling `esp_bt_controller_mem_release` or `esp_bt_mem_release` might result in exception if any of the regions returned to heap are empty. This happens usually if BT/BLE is enabled, but not used/linked in the final firmware.
1. BLE only with 9(max) connection will decrease 3K DRAM
2. BR/EDR only with 7(max) connection will decrease 16K DRAM
3. Any of BLE or BR/EDR connection number decrease will also decrease DRAM consumption
4. Decrease one BLE connection will save about 1KB DRAM
5. Decrease one BR/EDR ACL connection will save about 1.2KB DRAM
6. Decrease one BR/EDR SCO/eSCO will save 2KB DRAM.
7. fix some definition and kconfig
8. remove 1.2k of vhci tx cache and make .bss & .data to heap about 1.4K
9. modify BT Reserved Memory size and modify example to support new bt kconfig
Added bootloader_common_get_sha256_of_partition() and esp_partition_get_sha256() - get or calculate SHA-256
digest for app and data partitions.
Added bootloader_sha256_hex_to_str() - helps to print SHA-256 digest
Added esp_partition_check_identity() - compares two partitions by SHA-256 digest
Refactoring a function esp_image_load() in bootloader space to esp_image_verify() and
bootloader_load_image(). Old name function esp_image_load is deprecated
and will remove in V4.0 version.
spi_flash/sim: Fix error test_host. Add stub for bootloader_common_get_sha256_of_partition in sim/stubs
1. Add the 100 times test when the private key is generated by the random number;
2. Add the bt components to the unit-test-app/config directory.
3. Added the bt unit test case to CI.
For pins 32 and up the BIT(nr) macro used here overflowed,
causing undetermined GPIO pins to be reset.
Example: freeing SPI device/bus where CS is on pin 33
caused debug UART to cease communication, TXD0 was
disabled.
Fixed as BIT64(nr) macro, to be used elsewhere as needed.
For example in definitions like GPIO_SEL_32..GPIO_SEL_39.
1. modify parent switch mechanism.
2. fix non-root doesn't clear the layer value in nvs.
3. fix retransmit the remove announcement packets.
4. add API esp_mesh_flush_upstream_packets().
5. automatically adjust passsive scan time based on the change of beacon interval.
Component which includes component_ulp_common.mk may also need to set
some of the same COMPONENT_XXX variables. Logically, we should combine
the lists of files to embed, ldflags, extra include dirs, etc.
Fixes https://github.com/espressif/esp-idf/issues/2157.
1. The test step for error code REASON_ASSOC_EXPIRE is not reliable. SoftAP
could also send error code WIFI_REASON_NOT_AUTHED
2. STA will be disconnected now if softAP restart DHCP server
No longer necessary to keep all reserved addresses in 'soc'.
Means 'soc' does not need to know about 'bt', for example.
Also means that Bluetooth can be enabled in config without any memory being reserved for BT
controller. Only if code calling the BT controller is linked in, will this memory be reserved...
This change adds a check for compatibility between the nvs version
found on nvs flash and the one assumed by running code during nvs
initialization. Any mismatch is reported to the user using new error
code ESP_ERR_NVS_NEW_VERSION_FOUND.
Update libphy.a to v3960:
1. Decrease phy_init time from 900us to 347us in sleep wakeup
2. Fix RX STBC initialization
3. Modify set_chan function to fix interrupt watchdog issue
it will resolve the problem:
1. when bluetooth is running (For example: a2dp sink), wifi station cannot connect to AP easily
2. improve wifi connection success ratio when coexist is working
Based on report on forum here:
https://esp32.com/viewtopic.php?f=13&t=6382&p=27514
Previous versions were much more relaxed about what could be in the partition
table, erroring out avoids unexpected changes on upgrade like different
partition offsets.
- A bug of the http client when it downloads a chunked encoding packet is greater than the http_client's buffer, http_parser will call the callback body more than once, and the client will only handle the last
- with ssl_read, need to check before read to avoid timeout blocked when no data for reading
* spi_flash_mmap_pages needs pages array to be in internal memory.
Document and check this.
* Fix a bug that spi_flash_mmap did not allocate pages array in
internal memory.
* Minor style fixes: const-ify pages argument of spi_flash_mmap, add
spaces around operators, mark output arguments with [out].
Closes https://github.com/espressif/esp-idf/issues/2229.
The test is previously disabled for the requirement of external
connection. Now the signals are connected by internal connections.
Also change the failure logic of the test.
Fixed problem with multiple mount/unmount for different devices.
Additional check for structure length included into the code.
Remove useless spaces.
Added initialization for reserved memory.
WL version 2 mark used sectors as 16 bytes block of bytes with CRC.
This changes required because old version did not worked with encryption.
Additional unit tests are implemented.
Add a command `make erase_ota` - erases otadata if it there is in the
partition table otherwise error 'Partition table does not have ota_data partition'.
Closes https://github.com/espressif/esp-idf/issues/1821
heap_caps_malloc will fail to poison a block in IRAM with size not
divisible by 4. The proper fix will be to make poisoning code
smarter, or to disallow allocations from IRAM with size not aligned
by 4.
If we have the partition table without any ota_apps but in ota_data have
valide entry, in this case we get an error(hang). This commit fix this
case. If bs->app_count is zero when selecting the factory app.
Closes https://github.com/espressif/esp-idf/issues/2218
1. when one task do deinit/init/disable/enable, especially different cpu
core, it may cause controller crash in ISR handler
2. fix while BLE is scanning, bluetooth controller is disabled cause BLE
scan is not abort.
1. Modify esp_bt_controller_mem_release() to release BTDM BSS and Data to heap if
ESP_BT_MODE_BTDM mode is passed to it
2. Add a new API esp_bt_mem_release() which internally calls
esp_bt_controller_mem_release() with the provided mode and then if mode
is ESP_BT_MODE_BTDM, releases BT BSS and Data to heap.
Background:
For Wi-Fi and BT/BLE applications, for e.g. the usecase is like when
Bluetooth is used for provisioning and once the device is connected to the Wi-Fi
AP, we can turn off Bluetooth completely. In such scenarios, it should be possible to
reclaim all the memory of Bluetooth. Although, currently this does not
happen.
Experiment:
Made the following modifications to examples/bluetooth/gatt_server :
1. Added support of simple_wifi to it
2. Moved all the bluetooth related code under CONFIG_BT_ENABLED config
option
3. Calculated the free heap in 2 similar scenarios:
i. Disabled BT (CONFIG_BT_ENABLED undefined) and checked the free
heap after STA connected
ii. Kept BT enabled and disabled it after STA connected and checked
the free heap
Ideally, the numbers for i., ii. above should have been similar. But
there was a delta of almost 30-31K. (i. > ii.)
4. Through make size-components checked the common BSS for libbta.a and libbtdm_app.a
and found it to be almost 30K. Data is around 1K
Solution:
1. Modified the linker script to mark the BSS and Data for these libraries and
free it when ESP_BT_MODE_BTDM mode is passed to mem release APIs.
2. Verified that the free heap is comparable for i. and ii. above.
Note: It is known that once this is done, Bluetooth can only be used
again post reboot.
Signed-off-by: Hrishikesh Dhayagude <hrishi@espressif.com>
This change removes the earlier limitation of 1984 bytes for storing data-blobs.
Blobs larger than the sector size are split and stored on multiple sectors.
For this purpose, two new datatypes (multi-page index and multi-page data) are
added for entries stored in the sectors. The underlying read, write, erase and find
operations are modified to support these large blobs. The change is transparent
to users of the library and no special APIs need to be used to store these large
blobs.
* Fixes some "noreturn" functions in bootloader utils which did return (causing fatal CPU
exceptions).
* Marks bootloader entry as "noreturn", preventing "user code done" from stalling boot
Partial fix for https://github.com/espressif/esp-idf/issues/1814 TW20016
(Comprehensive fix for this issue will be enabling WDT during bootloader, coming shortly.)
1. Move channel to the first row of the table.
2. Remove the condition of HT20/HT40 for they are determined by
secondary channel.
3. Clean up the CSI table.
Because address space is mapped in 64KB pages, it was possible for unauthenticated data after the
app .bin to become mapped into the flash cache address space.
This problem is solved by 2 changes:
* "esptool elf2image --secure-pad" will pad the image so that the signature block ends close to the
64KB boundary. Due to alignment constraints it will be 12 bytes too short after signing (but
with flash encryption, these 12 bytes are still encrypted as part of the last block and can't be
arbitrarily changed).
* By default, secure boot now requires all app partitions to be a multiple of 64KB in size.
Perviously host send_auto_stop flag would be set for every data
transfer over 1 block long. This caused stop commands to be sent
after CMD53, which shouldn't be done. Fix by adding an explicit list
of commands for which send_auto_stop should be set.
Send the Goodbye packet while removing an mDNS service as an "Authoritative" packet so
that the listeners remove the service from their records immediately.
Fixed the error division on zero.
Also fixed range CONFIG_ESP32_RTC_CLK_CAL_CYCLES in Kconfig.
Fixed a overflow error by TIMG in the function rtc_clk_cal_internal. This error was due to a limit in values TIMG_RTC_CALI_MAX=0x7FFF (to write the slowclk_cycles) and TIMG_RTC_CALI_VALUE=0x1FFFFFF (to read xtal_cycles). Added assert finctions.
Closes https://github.com/espressif/esp-idf/issues/2147
1. Add reading psram EID.
2. Configure different clock mode for different EID.
3. add API to get psram size and voltage.
4. Remove unnecessary VSPI claim.
For 32MBit@1.8V and 64MBit@3.3V psram, there should be 2 extra clock cycles after CS get high level.
For 64MBit@1.8 psram, we can just use standard SPI protocol to drive the psram. We also need to increase the HOLD time for CS in this case.
EID for psram:
32MBit 1.8v: 0x20
64MBit 1.8v: 0x26
64MBit 3.3v: 0x46
When 2nd stage bootloader loads the ROM bootloader, it prints a
message similar to "entry 0x40080xxx", which idf_monitor decodes
(using application ELF file) as one of the reset vectors (xxx is <
400h). This moves the iram_seg of bootloader 1k up to prevent overlap
of bootloader .text and application vectors, making the output look
nicer. There is still a chance that the entry point decodes as some
symbol in application ELF file, but at least it won't have
"Exception" in its name.
Since 94250e42a0, UART output is suspended when entering sleep mode
(deep or light sleep). This makes sense for light sleep, where sleep
normally takes small amount of time, and flushing the UART would add
a lot of latency. But this breaks existing behaviour for deep sleep,
where UART output was previously sent out before entering sleep mode.
Closes https://github.com/espressif/esp-idf/issues/2145
remote_ip was declared to be a pointer to an address that was
overwritten in later stage thus changing the address pointed by remote_ip
esp_smartconfig.h : Fixed a typo. station_config to wifi_config_t
Signed-off-by: Sachin Parekh <sachin.parekh@espressif.com>
An existing UART driver does not support RS485 half duplex mode.
This task adds this functionality to ESP_IDF UART driver.
driver/uart.c/h: updated to add support of RS485 half duplex mode
examples/peripherals/uart_echo_rs485/main/rs485_example.c: added test example
components/driver/test/test_uart.c: added test of RS485 half duplex mode
docs/en/api-reference/peripherals/uart.rst: updated documentation
test_uart.c: suppress GCC warnings about discarded const qualifiers
uart.rst: remove sphinx warning - "Duplicate explicit target name"
simple change in uart.h file
update (test_uart.c) after rebase from master
update uart.rst, uart.c, rs485_example.c
Update example description in file Readme.md
update uart.c/h, uart.rst, test_uart.c according to review results
update uart.h (uart_set_rx_timeout() description
test_uart.c remove ignore tag
uart.c/h: fix param errors
test_uart.c: Remove GCC warning supress
uart.rst: fix the notes
rs485_example.c: fix output
uart.c: remove reset using UART_RXFIFO_RST from driver.
readme.md: Update example description
The tests are completed using RS485 adapters hardware connected to two ESP32 WROVER KITs.
TW#13812
Closes https://github.com/espressif/esp-idf/pull/667
Closes https://github.com/espressif/esp-idf/pull/1006
An existing UART driver does not support RS485 half duplex mode.
This task adds this functionality to ESP_IDF UART driver.
driver/uart.c/h: updated to add support of RS485 half duplex mode
examples/peripherals/uart_echo_rs485/main/rs485_example.c: added test example
components/driver/test/test_uart.c: added test of RS485 half duplex mode
docs/en/api-reference/peripherals/uart.rst: updated documentation
test_uart.c: suppress GCC warnings about discarded const qualifiers
uart.rst: remove sphinx warning - "Duplicate explicit target name"
simple change in uart.h file
update (test_uart.c) after rebase from master
update uart.rst, uart.c, rs485_example.c
Update example description in file Readme.md
update uart.c/h, uart.rst, test_uart.c according to review results
update uart.h (uart_set_rx_timeout() description
test_uart.c remove ignore tag
uart.c/h: fix param errors
test_uart.c: Remove GCC warning supress
uart.rst: fix the notes
rs485_example.c: fix output
The tests are completed using RS485 adapters hardware connected to two ESP32 WROVER KITs.
TW#13812
Closes https://github.com/espressif/esp-idf/pull/667
Closes https://github.com/espressif/esp-idf/pull/1006
An existing UART driver does not support RS485 half duplex mode.
This task adds this functionality to ESP_IDF UART driver.
driver/uart.c/h: updated to add support of RS485 half duplex mode
examples/peripherals/uart_echo_rs485/main/rs485_example.c: added test example
components/driver/test/test_uart.c: added test of RS485 half duplex mode
docs/en/api-reference/peripherals/uart.rst: updated documentation
test_uart.c: suppress GCC warnings about discarded const qualifiers
uart.rst: remove sphinx warning - "Duplicate explicit target name"
simple change in uart.h file
update (test_uart.c) after rebase from master
update uart.rst, uart.c, rs485_example.c
Update example description in file Readme.md
update uart.c/h, uart.rst, test_uart.c according to review results
update uart.h (uart_set_rx_timeout() description
test_uart.c remove ignore tag
uart.c/h: fix param errors
test_uart.c: Remove GCC warning supress
uart.rst: fix the notes
rs485_example.c: fix output
The tests are completed using RS485 adapters hardware connected to two ESP32 WROVER KITs.
TW#13812
Closes https://github.com/espressif/esp-idf/pull/667
Closes https://github.com/espressif/esp-idf/pull/1006
An existing UART driver does not support RS485 half duplex mode.
This task adds this functionality to ESP_IDF UART driver.
driver/uart.c/h: updated to add support of RS485 half duplex mode
examples/peripherals/uart_echo_rs485/main/rs485_example.c: added test example
components/driver/test/test_uart.c: added test of RS485 half duplex mode
docs/en/api-reference/peripherals/uart.rst: updated documentation
test_uart.c: suppress GCC warnings about discarded const qualifiers
uart.rst: remove sphinx warning - "Duplicate explicit target name"
simple change in uart.h file
update (test_uart.c) after rebase from master
update uart.rst, uart.c, rs485_example.c
Update example description in file Readme.md
update uart.c/h, uart.rst, test_uart.c according to review results
update uart.h (uart_set_rx_timeout() description
test_uart.c remove ignore tag
The tests are completed using RS485 adapters hardware connected to two ESP32 WROVER KITs.
TW#13812
Closes https://github.com/espressif/esp-idf/pull/667
Closes https://github.com/espressif/esp-idf/pull/1006
An existing UART driver does not support RS485 half duplex mode.
This task adds this functionality to ESP_IDF UART driver.
driver/uart.c/h: updated to add support of RS485 half duplex mode
examples/peripherals/uart_echo_rs485/main/rs485_example.c: added test example
components/driver/test/test_uart.c: added test of RS485 half duplex mode
docs/en/api-reference/peripherals/uart.rst: updated documentation
test_uart.c: suppress GCC warnings about discarded const qualifiers
uart.rst: remove sphinx warning - "Duplicate explicit target name"
simple change in uart.h file
update (test_uart.c) after rebase from master
update uart.rst, uart.c, rs485_example.c
Update example description in file Readme.md
update uart.c/h, uart.rst, test_uart.c according to review results
update uart.h (uart_set_rx_timeout() description
The tests are completed using RS485 adapters hardware connected to two ESP32 WROVER KITs.
TW#13812
Closes https://github.com/espressif/esp-idf/pull/667
Closes https://github.com/espressif/esp-idf/pull/1006
An existing UART driver does not support RS485 half duplex mode.
This task adds this functionality to ESP_IDF UART driver.
driver/uart.c/h: updated to add support of RS485 half duplex mode
examples/peripherals/uart_echo_rs485/main/rs485_example.c: added test example
components/driver/test/test_uart.c: added test of RS485 half duplex mode
docs/en/api-reference/peripherals/uart.rst: updated documentation
test_uart.c: suppress GCC warnings about discarded const qualifiers
uart.rst: remove sphinx warning - "Duplicate explicit target name"
simple change in uart.h file
update (test_uart.c) after rebase from master
update uart.rst, uart.c, rs485_example.c
Update example description in file Readme.md
update uart.c/h, uart.rst, test_uart.c according to review results
The tests are completed using RS485 adapters hardware connected to two ESP32 WROVER KITs.
TW#13812
Closes https://github.com/espressif/esp-idf/pull/667
Closes https://github.com/espressif/esp-idf/pull/1006
components/wpa_supplicant/port/include/os.h:259:29: error: 'strncpy' output truncated before terminating nul copying 3 bytes from a string of the same length [-Werror=stringop-truncation]
#define os_strncpy(d, s, n) strncpy((d), (s), (n))
^~~~~~~~~~~~~~~~~~~~~~
components/wpa_supplicant/src/wpa2/eap_peer/eap.c:410:3: note: in expansion of macro 'os_strncpy'
os_strncpy(sm->blob[0].name, CLIENT_CERT_NAME, BLOB_NAME_LEN);
^~~~~~~~~~
components/spi_flash/partition.c: In function 'load_partitions':
components/spi_flash/partition.c:179:66: error: argument to 'sizeof' in 'strncpy' call is the same expression as the source; did you mean to use the size of the destination? [-Werror=sizeof-pointer-memaccess]
strncpy(item->info.label, (const char*) it->label, sizeof(it->label));
^
components/fatfs/src/ff.c: In function 'f_fdisk':
components/fatfs/src/ff.c:5995:5: error: this 'for' clause does not guard... [-Werror=misleading-indentation]
for (n = 16; n < 256 && sz_disk / n / cluster_size > 1024; n *= 2) ;
^~~
components/fatfs/src/ff.c:5996:2: note: ...this statement, but the latter is misleadingly indented as if it were guarded by the 'for'
if (n == 256) n--;
^~
components/esp32/ipc.c: In function 'esp_ipc_init':
components/esp32/ipc.c:82:31: error: '%d' directive writing between 1 and 11 bytes into a region of size 5 [-Werror=format-overflow=]
sprintf(task_name,"ipc%d",i);
^~
components/esp32/ipc.c:82:27: note: directive argument in the range [-2147483648, 1]
sprintf(task_name,"ipc%d",i);
^~~~~~~
components/esp32/ipc.c:82:9: note: 'sprintf' output between 5 and 15 bytes into a destination of size 8
sprintf(task_name,"ipc%d",i);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~
INTERRUPT and CCOUNT registers will change outside of program control.
Making the inline assembly used to read these registers volatile
indicates this fact to the compiler.
Fixes https://github.com/espressif/esp-idf/issues/2127
The fix is for the situation when cache disabling mechanism causes
a deadlock with user tasks. Situation is as follows:
1. spi_flash operation is started from low-priority task on CPU0
2. It uses IPC to wake up high-priority IPC1 task on CPU1, preventing
all other tasks on CPU1 from running. This is needed to safely
disable the cache.
3. While the task which started spi_flash operation is waiting for IPC1
task to acknowledge that CPU1 is not using cache anymore, it is
preempted by a higher priority application task ("app0").
4. Task app0 busy-waits for some operation on CPU1 to complete. But
since application tasks are blocked out by IPC1 task, this never
happens. Since app0 is busy-waiting, the task doing spi flash
operation never runs.
The more or less logical soltion to the problem would be to also do
cache disabling on CPU0 and the SPI flash operation itself from IPC0
task. However IPC0 task stack would need to be increased to allow doing
SPI flash operation (and IPC1 stack as well). This would waste some
memory. An alternative approach adopted in this fix is to call FreeRTOS
functions to temporary increase the priority of SPI flash operation task
to the same level as the IPC task.
Fixes https://github.com/espressif/arduino-esp32/issues/740
Fixes https://github.com/espressif/esp-idf/issues/1157
1. fix BLE connection missing in coex mode
2. modify other parameters to make coex priority more reasonable
3. fix modem sleep procedure trap cause Wifi disable RF when BT is
working. Such cause that BR/EDR is difficult to be connected, BLE
connection stability decrease and so on.
4. modify BR/EDR coexist duration to imrove BR/EDR connect success
ratio.
5. Due to the hardware coexist bug, BLE scan interval/window should
be less than 0x100(about 160ms). Therefore, it will cause BLE cannot
scan any advertising packet while WiFi have higher priority
behaviour(such like RX beacon, scan, TX/RX VO packets and etc.).
