SD SPI mode driver
This MR adds functionality to support SD cards connected via SPI interface.
Additionally, two bugs are fixed:
- Definition of `SPI_TRANS_MODE_DIOQIO_ADDR` in spi_master driver
- SD card probing frequency was 4000kHz instead of 400kHz as required by the standard
See merge request !727
gpio_matrix_out function will set output enable for GPIO, seems in gpio_matrix_out there will be a short moment that the chip will output GPIO level.
So we can set GPIO as high before gpio_matrix_out function.
Makes app image booting more reliable (256-bit rather than 8-bit verification.)
Some measurements, time to boot a 655KB app.bin file and run to app_main() execution.
(All for rev 1 silicon, ie no 340ms spurious WDT delay.)
80MHz QIO mode:
before = 300ms
after = 140ms
40MHz DIO mode:
before = 712ms
after = 577ms
40MHz DIO mode, secure boot enabled
before = 1380ms
after = 934ms
(Secure boot involves two ECC signature verifications (partition table, app) that take approx 300ms each with 80MHz CPU.)
For config-only components, component.mk should now contain "COMPONENT_CONFIG_ONLY := 1"
Also refactored some of the generation of linker paths, library list. This required cleaning up the way the bootloader
project works, it's now mostly independent from the parent.
1. add ble tx power functions
2. add more osi functions.
3. modify bluetooth controller task procedure
4. fix a memory leak when controller deinit
5. add controller disable return value.
NVS is used to store PHY calibration data, WiFi configuration, and BT
configuration. Previously BT examples did not call nvs_flash_init,
relying on the fact that it is called during PHY init. However PHY init
did not handle possible NVS initialization errors.
This change moves PHY init procedure into the application, and adds
diagnostic messages to BT config management routines if NVS is not
initialized.
In ecp_mul_comb(), if (!p_eq_g && grp->T == NULL) and ecp_precompute_comb() fails (which can happen due to OOM), then the new array of points T was leaked.
Currently the last 128KB of DRAM is reserved for the bootloader & early boot stacks. This means if >192KB of static DRAM
is allocated, the only available heap is this region - which is disabled until the scheduler starts. As a result, you
get either heap corruption on early boot if the static data overlaps startup heap (leading to very weird errors), or
FreeRTOS will fail to start when it can't malloc() anything.
Long term fix is to move the stacks & bootloader data to the very end of RAM, and only reserve that part for early
boot. This is a little fiddly because of also wanting to make sure this memory is not preemptively fragmented when it
gets reintroduced to the heap. This will become more important if/when we have more static allocation options in the
future.
For now, these errors make it clear why the boot has failed.
Ref TW13909
Because of errata related to BOD reset function, brownout is handled as follows:
- attach an ISR to brownout interrupt
- when ISR happens, print a message and do a software restart
- esp_restart_nonos enables RTC watchdog, so if restart fails,
there will be one more attempt to restart (using the RTC
watchdog)
RTC watchdog didn’t have any actions configured for any of the stages.
This change configures it to use SW_SYSTEM_RESET at stage 0 and a
full reset at stage 1. The timeout is now calculated based on
RTC_SLOW_CLK frequency.
unused variable 'lfn'
'isr_handler' defined but not used
'servo_set_angle' defined but not used
'gpio_test_signal' defined but not used
'change_duty' defined but not used
component/bt: Fixed the bug crash of disconnet BLE when close the SMP module in the menuconfig.
component/bt: Removed the Excess #endid ///SMP_INCLUDED == TRUE in the l2cu_no_dynamic_ccbs function.
If destination IP address of the packet is broadcast address, firstly compare
source IP address with the that of each network interface. If it matches,
packet is forwarded from the interface.
If scheduler was running, and lock was an automatic variable (ie stack-allocated) to be initialised by _lock_init*,
initialisation could be skipped if the lock variable was non-zero (and lock would be left invalid).
In other cases the lock is statically initialised to zero by __LOCK_INIT*
Specifying -fexceptions for the compiler is not enough.
- add necessary zero padding after .eh_frame section
- link .gcc_except_table_table in a way flash script does not complain
- call __registrer_frame_info before global constructors
Kudos jcmvbkbc for the necessary help.
Implements support for system level traces compatible with SEGGER
SystemView tool on top of ESP32 application tracing module.
That kind of traces can help to analyse program's behaviour.
SystemView can show timeline of tasks/ISRs execution, context switches,
statistics related to the CPUs' load distribution etc.
Also this commit adds useful feature to ESP32 application tracing module:
- Trace data buffering is implemented to handle temporary peaks of events load
Fixes issue with GPIO 0 being enabled as an output on ESP32D2WD (or when setting SPI pins in efuse)
and not using Quad-I/O modes.
Ref: https://esp32.com/viewtopic.php?f=2&t=2205
Bug occurs when core dump destination in menuconfig is set to flash. When
programme crashes, xt_unhandled_exception or panicHandler will both trigger
commonErrorHandler. commonErrorHandler calls esp_core_dump_to_flash which
will attempt to use DPORT functions and hang due to trying to a stall and already
stalled processor (already stalled in xt_unhandled_exception and panicHandler).
Program will eventually be rebooted when wdt expires.
Added esp_dport_access_int_deinit after calls to haltOtherCore() so that DPORT
functions don't try to halt and already halted cpu hence preventing hang.
Fixes TW#12944 https://github.com/espressif/esp-idf/issues/646
Previously opendir("/data") would fail if filesystem with "data" prefix
was registered in VFS, while opendir("/data/") would succeed.
This change fixes handling for the former case and adds relevant tests.
Updated test case to include configASSERT cases (+1 squashed commits)
Squashed commits:
[871ec26f] Freertos:Bugfix uxTaskGetSystemState
Bug (github #12142) with uxTaskGetSystemState where
if called immediately after creating a bunch of tasks,
those tasks would be added twice into the TaskStatusArray.
Bug caused due to use old implementation using vTaskSuspendAll
which did not stop newly created task on other core from accessing the
read/waiting task lists whilst the list were being read by
uxTaskGetSystemState. Fixed bug by replacing vTaskSuspendAll
with taskENTER_CRITICAL and added test case for the bugfix
Small changes to clock calibration value will cause increasing errors
the longer the device runs. Consider the case of deep sleep, assuming
that RTC counter is used for timekeeping:
- before sleep:
time_before = rtc_counter * calibration_val
- after sleep:
time_after = (rtc_counter + sleep_count) * (calibration_val + epsilon)
where 'epsilon' is a small estimation error of 'calibration_val'.
The apparent sleep duration thus will be:
time_after - time_before = sleep_count * (calibration_val + epsilon)
+ rtc_counter * epsilon
Second term on the right hand side is the error in time difference
estimation, it is proportional to the total system runtime (rtc_counter).
To avoid this issue, this change makes RTC_SLOW_CLK calibration value
persistent across restarts. This allows the calibration value update to
be preformed, while keeping time after update same as before the update.
1. For now, some security related functions used in classic Bluetooth are controlled by "SMP_ENABLE". This commit fixes the dependency.
2. The two options, "CLASSIC_BT_ENABLED" and "SMP_ENABLED" The two options will be decoupled in the future.
Currently libsodium tests add about 800kB to the binary, which is too
much for a partition table constrained to 2MB. Disable libsodium tests
until we start building multiple unit test apps for different subsets.
This fixes a bug introduced by !848, where APP CPU would not be reset
during esp_restart, if esp_restart was called from a task running on APP
CPU, and wouldn’t be reset by PRO CPU on startup.
This change replaces stalling APP CPU with resetting it.
Also adds a non-automated esp_restart tests.
DPORT access protection can not work when the other CPU is stalled.
Writes to DPORT registers in esp_restart caused the program to hang due
to access protection, and the reset happened due to RTC_WDT, not SW_RST.
This change adds esp_dport_access_int_deinit function and calls it from
esp_restart once the other core is stalled.
In ESP32 rev. 0, switching between 240MHz and 80MHz (even via an
intermediate frequency of 40MHz) may cause the chip to lock up.
The bootloader used to enable 80MHz CPU clock at startup, which could
cause lock up after software reset. With this change, if 240MHz CPU
clock is enabled in menuconfig, bootloader will also use 240MHz to avoid
lock-up.
Run some unit test cases based (poorly) around sodium's test infrastructure.
Increase in unity test task stack is due to signature tests, load a lot of data onto the stack.
- Fix slave initiate service discovery procedure
- Fix master re-discovery every time connection established
- Optimize service discovery char ccc write procedure
- Optimize esp_log_buffer function
- Modify default supervision timeout from 20s to 2s
This seems to clean up some of the more wrong addr2line output results (not
sure why, something to do with optimisations I think - perhaps the return
address may also be a jump target from some earlier line of the code.)
Previously, this resulted in task stack frames turning up incorrectly in the backtrace, ie
Backtrace: 0x400d22a0:0x3ffb0fa0 0x40085a3c:0x3ffb0fc0 0x400f32c4:0x3ffb0fe0 0x40081965:0x3ffb1010
0x400d22a0: esp_vApplicationIdleHook at /home/esp/esp-idf/components/esp32/./freertos_hooks.c:
52
0x40085a3c: prvIdleTask at /home/esp/esp-idf/components/freertos/./tasks.c:4431
0x400f32c4: i2c_isr_handler_default at /home/esp/esp-idf/components/driver/./i2c.c:598
0x40081965: _xt_lowint1 at xtensa_vectors.o:?
Fix is to implement abort() via an unhandled exception rather than a breakpoint, I think
because of relative priority of exception types.
Another approach would be to assign a software-only INUM to abort()ing and defined a
PANIC_RSN_ABORTED, but this is more complex and interrupt numbers are more scarce than RAM!
This change removes the erroneous cast to uint32_t (which caused time to
wrap around after 1 hour) and splits the multiplication into two terms
to remove the wraparound after 13 days.
Ref. https://esp32.com/viewtopic.php?f=13&t=1908
When ‘reset halt’ command is executed, OpenOCD will take the APP CPU
out of reset and enable the clock. At this point, user can set a
breakpoint on code which will run on APP CPU. Previously, app startup
code would do another reset of APP CPU, thereby removing any breakpoints
which may have been set. This change makes APP CPU reset conditional on
DPORT_APPCPU_CLKGATE_EN bit, which is 0 by default but is set to 1 by
OpenOCD after reset.
* Writing >4 bytes to unaligned offsets would fail
* Writiing data from flash would fail (wrong buffer was used)
* Writing >8192 bytes from RAM would over-write data multiple times
Adds test cases for the above.
Previously the first call to rmt_driver_uninstall() would remove the interrupt handler,
even if other channels still had the driver installed.
Adds an OS-level lock to control concurrent registration/deregistration of channels.
xPendingReadyList[1] was never initialised correctly, so if a task is added to this list (ie by xSemaphoreGiveFromISR()
or similar) while scheduler is disabled, then it causes a null pointer dereference.
Bug produces stack traces similar to:
0x40086e87: vListInsertEnd at /home/gus/esp/32/idf/components/freertos/./list.c:130
0x40084ba3: xTaskRemoveFromEventList at /home/gus/esp/32/idf/components/freertos/./tasks.c:3439
0x40083c54: xQueueGiveFromISR at /home/gus/esp/32/idf/components/freertos/./queue.c:2034
0x400f50a0: timer_group0_isr at /home/gus/esp/32/idf/components/freertos/test/./test_suspend_scheduler.c:27
0x40081d7d: _xt_lowint1 at xtensa_vectors.o:?
Writing values longer than half of the page size (with header taken into
account) causes fragmentation issues. Previously it was suggested on the
forum that using long values may cause issues, but this wasn’t checked
in the library itself, and wasn’t documented. This change adds necessary
checks and introduces the new error code.
Documentation is also fixed to reflect the fact that the maximum length
of the key is 15 characters, not 16.
component/bt: squash the branch of the early commit
component/bt: Added the set static random address callback to the bt project.
component/bt: fixed the set static random address error.
component/bt: fixed the set static random address error.
To increase the chances that the examples work out of the box, this
change is raising the default deep sleep wakeup delay to 1ms.
If GPIO15 is low at startup, ROM code takes less time to execute
(because no logging is performed), so more time may be needed to allow
flash chip to become ready.
Triggered on make 3.81, happens sometimes on Linux and always(?) on macOS. May depend on the order the OS' filesystem
resolves wildcards in.
Includes a revert to the LWIP component to verify this is properly fixed.
See also https://github.com/espressif/esp-idf/issues/632
Fix Dport access in interrupts
Dport accesses would re-enable interrupts unconditionally, breaking things when called in an ISR. This saves and restores the interrupt status, fixing this.
This fixes a crash in the SPI slave driver, and possibly other things.
See merge request !772
CI: auto generate configs for test jobs
Currently CI test jobs are static configured by several pre-generated config files.
This approach have several disadvantages:
1. not flexible to select test cases to run, which is important feature of @bot
2. difficult to update test as we need to pre-generate quite a lot files
3. need to maintain extra config files in IDF
4. not flexible to support new test apps or chips, can't use some new features of test bench
Therefore we'll add assign_test stage between build and test, to generate configs for test jobs.
See merge request !738
Make internal stack size variables in FreeRTOS 32-bit instead of 16-bit
Stock FreeRTOS uses an uint16 to store stack sizes, making it impossible to allocate a stack >64K. This changes this into an uint32, allowing for larger stacks.
See merge request !677
Partition table gen esp32part fixes: App offset errors, Python 3 support
As mentioned on forums, gen_esp32part.py wasn't erroring correctly if a non-64KB-aligned app partition was referenced.
Also merges a PR to add Python 2&3 support (with some tweaks). Not very useful in IDF right now, but useful for Arduino.
See merge request !751
1. Name change from chopper to carrier, block diagram update, minor changes to example codes
2. mcpwm_reg.h changed, brought uniformity in comments, worked on suggestions, duty to accept float. Some name changes!
3. Minor readme changes and Indetation
4. Minor change: move mcpwm_reg.h and mcpwm_struct.h to new path
5. Minor change: addition of BLDC example code and Readme
6. Name changed from epwm to mcpwm
7. Improve the reg name in mcpwm_struct.h
8. Name change chopper>carrier, deadband>deadtime
component/bt: fix the exception in attp_buil_sr_msg when handling gatt write bug. bug number #12124.
fix the exception in attp_buil_sr_msg when handling gatt write bug.
See merge request !743
Small unit-test-related fixes
Fixes for some small bugs found running unit tests with heap poisoning turned on.
All are bugs in the tests, except for one FreeRTOS fix (when deleting a task, check if it's running on the other CPU and preempt it if so.)
See merge request !746
nvs: remove search cache at page level
Since read cache was introduced at page level, search cache became
useless in terms of reducing the number of flash read operations.
In addition to that, search cache used an assumption that if pointers to
keys are identical, the keys are also identical, which was proven wrong
by applications which generate key names dynamically.
This change removes CachedFindInfo, and all its uses. This is done at
expense of a small extra number of CPU operations (looking up a value in
the read cache is slightly more expensive) but no extra flash read
operations.
Ref TW12505
Ref https://github.com/espressif/arduino-esp32/issues/365
See merge request !753
Since read cache was introduced at page level, search cache became
useless in terms of reducing the number of flash read operations.
In addition to that, search cache used an assumption that if pointers to
keys are identical, the keys are also identical, which was proven wrong
by applications which generate key names dynamically.
This change removes CachedFindInfo, and all its uses. This is done at
expense of a small extra number of CPU operations (looking up a value in
the read cache is slightly more expensive) but no extra flash read
operations.
Ref TW12505
Ref https://github.com/espressif/arduino-esp32/issues/365
1. Enlarge wifi task stack size by 512Bytes to fix potential stack overflow issue
2. Modify wifi hmac tx queue size from 12 to 32 because we already limit the buffer number in ebuf
management module
add API to get chip info
This change adds an API to get chip info, such as chip model, enabled capabilities, size of embedded flash, silicon revision.
Hello_world example is modified to print out the information about the chip. The example is also simplified by moving all code into the main task.
Ref TW12031.
See merge request !549
esp32: update wifi lib for some bugfix
1. Fix wifi ebuf free twice issue
2. Fix wifi internal assert issue
3. Fix a bug in esp_wifi_stop
4. Fix wifi crash issue
5. Fix wifi run out of memory when 10 udp connection stability test
See merge request !745
Optimize configuration of base MAC address
Application developer can call APIs to configure base MAC address
instead of using menuconfig.
See merge request !744
component/esp32 : fix dualcore bug
1. When dual core cpu run access DPORT register, must do protection.
2. If access DPORT register, must use DPORT_REG_READ/DPORT_REG_WRITE and DPORT_XXX register operation macro.
See merge request !742
component/bt: fix adv stop event bug and add attribute table create
- Fix bug that advertising stop event produced while calling start_adv function
- Modify gatt server adv data and scan rsp data raw setting
- Add create attribute table error msg
- Delete redundant printf in previous commits
See merge request !739
1. When dual core cpu run access DPORT register, must do protection.
2. If access DPORT register, must use DPORT_REG_READ/DPORT_REG_WRITE and DPORT_XXX register operation macro.
SPI: Various fixes (examples, mem leak, arg check)
- Fix SPI master example to use DMA-capable memory for display initialization. Fixes https://github.com/espressif/esp-idf/issues/551
- SPI master: Do not leak DMA descriptor pointer array on free
- SPI Master/Slave: Check if DMA'ed buffers actually live in DMA-capable memory
See merge request !735
error
- Fix bug that advertising stop event produced while calling start_adv function
- Modify gatt server adv data and scan rsp data raw setting
- add create attribute table error msg
- Delete redundant printf in previous commits
we'll auto assign cases to test jobs so we don't need those config
files. cases with different wifi modes will now be generated when
creating test case database, we need to remove them from YAML files.
FATFS fixes and tests
This MR includes a set of fixes related to FATFS, SDMMC, and wear levelling:
- `esp_vfs_fat_spiflash_mount` uses `FM_SFD` flag when creating the partition. The volume layout (given in `VolToPart` variable) was not compatible with SFD mode, so mkfs was failing. This fixes the volume layout to use "autodetect" for both volumes. Merges https://github.com/espressif/esp-idf/pull/559.
- fix `prepend_drive_to_path`function, which didn't prepend drive to path (while consuming 2k of stack space)
- fix stack overflow in vfs_fat_link function which allocated two 4kbyte `FIL` structures on the stack
- fix support for having two FATFS instances (in flash and SD) mounted at the same time
- unit tests written for FATFS on SDMMC are made common between SDMMC and WL implementations; FATFS unit tests on WL will run during CI
- fix inconsistent definition of PATH_MAX and ARG_MAX (TW12207, TW12104, https://github.com/espressif/esp-idf/issues/289)
See merge request !732
component/bt: fix some bugs related to bluetooth sniff mode in controller
1. fix some bugs in bluetooth sniff mode in controller
2. export some symbols to esp32.rom.ld including functions and global variables in ROM code
3. update libbtdm.a which includes "IRAM_ATTR" addition or removal for some functions
See merge request !729
fix(lwip): fix tcp connect fail when enable LOOPIF
when enable the LOOPIF, because of use the loopnetif, the TCP connect will fail. see TW12029
See merge request !711
- fix null pointer dereference in VFS when VFS implementations are added
and removed in different order
- vfs_fat_sdmmc, vfs_fat_spiflash: pass correct drive to mkfs
(previously it would always do mkfs in the first drive)
- add test case
This change moves actual test code into test_fatfs_common.c and
refactors setup/teardown code to be contained within separate functions.
For each SDMMC FATFS test, identical test is added which can run with
WL partition in flash.
vfs_fat_link opened two files to perform copy operation. File structures
were allocated on the stack. When _MAX_SS setting was increased in
ffconf.h due to wear levelling feature, the size of these structures
increased to ~4k each (~8k total). This exceeds stack size allocated for
tasks in most typical cases.
This change makes file structures dynamically allocated.
Originally, prepend_drive_to_path was designed to be a macro, and it
modified local path variables to point to a temporary buffers.
When it was converted into a function, modification to path variables
were no longer visible outside of this function.
In addition to that, prepend_drive_to_path allocated 2k bytes on the
stack for temporary path buffers. This is replaced with path buffers
allocated as part of vfs_fat context object. Locking is added around
parts of code which use these temporary buffers.
Additionally, _lock member of vfs_fat_ctx_t was placed after the
variable-sized files array, which caused the first entry in the
array to be never used. This change fixes the order of members
and adds comments.
1. fix some bugs in bluetooth sniff mode in controller
2. export some symbols to esp32.rom.ld including functions and global variables in ROM code
3. update libbtdm.a which includes "IRAM_ATTR" addition or removal for some functions
component/bt:fix the bug with gatt client cant not receive the gatt server service change event.
fix the bug with gatt client cant not receive the gatt server service change event.
See merge request !726
esp32: select 8M clock as RTC_FAST_CLK on startup
Even though RTC_CLK_CONFIG_DEFAULT correctly had RTC_FAST_FREQ_8M as the
fast clock, the bootloader modified fast_freq field to the currently
selected RTC_FAST_CLK (so that the clock choice is not affected by the
bootloader). The application startup code never switched to 8M clock,
which caused the default (XTAL/4) to be used as RTC_FAST_CLK. This had
caused a number of issues, such as touch pads not working in deep sleep.
Fixes https://github.com/espressif/esp-idf/issues/542.
Ref TW12053.
See merge request !709
Assert when a new task is started on a nonexisting CPU
Previously, starting a task on a CPU ID higher than the amount of CPUs FreeRTOS is configured with would not start the task and possibly have unintended side effects due to some out-of-bounds array writes. Assert on this so the app aborts cleanly.
See merge request !701
I2S driver - fixed support for 24 and 32-bits, fixed tx/rx at the same time
- Modify sample can test with 24, 32-bits audio
- Add i2s sample README
- simply i2s_push function
- change sample rates, bits per sample, channel on fly
See merge request !483
Fix SPI master CI test
CI test fails because the values it checks haven't been updated to the changes in the clock calculations. This fixes that.
See merge request !710
Feature/btdm ble bt separa
@Jack @snake @igrokhotkov @angus @island please help to review the code.
Separate the bt/ble code. After the separate, can save 15k~25k ram & 240k~460k code size(depending on the menuconfig).
See merge request !684
optimize scan before station connecting to AP
1. Store the information of AP(ssid, password, bssid, channel, etc)
into nvs when station connects to AP successfully. If station
connects to the same AP next time, it will scan the stored channel of the AP
first.
2. Add a parameter of channel for scanning before connecting to AP.
If the channel is set to 0, station will scan full channels. If it
is set to 1~13, station will only scan the channel.
See merge request !704
1. Store the information of AP(ssid, password, bssid, channel, etc)
into nvs when station connects to AP successfully. If station
connects to the same AP next time, it will scan the stored channel of the AP
first.
2. Add a parameter of channel for scanning before connecting to AP.
If it is set to 1~13, station will scan starting from the channel.
If the channel of AP is unknown, set it to 0.
Even though RTC_CLK_CONFIG_DEFAULT correctly had RTC_FAST_FREQ_8M as the
fast clock, the bootloader modified fast_freq field to the currently
selected RTC_FAST_CLK (so that the clock choice is not affected by the
bootloader). The application startup code never switched to 8M clock,
which caused the default (XTAL/4) to be used as RTC_FAST_CLK. This had
caused a number of issues, such as touch pads not working in deep sleep.
Fixes https://github.com/espressif/esp-idf/issues/542.
Ref TW12053.
Split common SPI stuff out of master driver; add slave driver; add workaround for DMA issue.
This merge req mainly adds a slave device. In order to do this, the original master driver is refactored into common code shared by master and slave modes, and a slave driver is added.
The other things added are:
- Added a workaround for a 'feature' of the ESP32 silicon that can lock up the receive DMA channel in some situations. This can only be fixed by resetting *both* DMA channels. The workaround implemented makes sure that the reset only happens when both channels are idle
- Got rid of the automatic choice between register- and DMA-based transfers. The master (and slave) code will now always go for a DMA transfer if a DMA channel is given, and always go for register-based transfers if no DMA channel is given.
- Add in a bunch of fixes for outstanding Github issues.
See merge request !659
Add support 24, 32 bits
@jxmao optimize i2s_zero_buffer
@jxmao correct config support slave mode
@jxmao correct setup pin support tx/rx at the same time
Enhance pin power
@jxmao add dynamic change number of channels
remove nvs_init
remove start log and enhance power pin setup
using enum for i2s_channel and i2s_bits_per_sample, return ESP_ERR_INVALID_ARG when check params
validate i2s_bits_per_sample and channel
check tx & rx buffer before fill zero
remove checking channel as @jxmao suggest
limit dma buffer
modify i2s pin back to gpio mux before configure gpio matrix, resolve github issue #512
Add support 24, 32 bits
reduce push function
Modify sample can test with 24, 32-bits
Add i2s sample README
Fixed i2s_set_clk got reset sometime
can changes bit-wide while running
Fix sample rate calculation for DAC mode from @jeroen
modify example can change bits per sample every 5 seconds
cleanup
add comment for bytes_per_sample
update as @angus suggestions
Add i2s_set_clk api
I2S driver bug fixed as following log:
@jxmao optimize i2s_zero_buffer
@jxmao correct config support slave mode
@jxmao correct setup pin support tx/rx at the same time
Enhance pin power
@jxmao add dynamic change number of channels
remove nvs_init
remove start log and enhance power pin setup
using enum for i2s_channel and i2s_bits_per_sample, return ESP_ERR_INVALID_ARG when check params
validate i2s_bits_per_sample and channel
check tx & rx buffer before fill zero
remove checking channel as @jxmao suggest
limit dma buffer
modify i2s pin back to gpio mux before configure gpio matrix, resolve github issue #512
limit dma buffer to 4092
change gpio_matrix_*_check to inline function, remove some comments and rename test_i2s function to setup_triangle_sine_waves
for change commit title
esp32: Core dump sanity checks
Adds sanity checks when doing core dump to flash
- CRC for core dump flash partition config
- Tasks with corrupted TCBs are skipped
- Assertions to check that nothing is written beyond core dump flash partition
Ref TW11879
See merge request !686
- CRC for core dump flash partition config
- Tasks with corrupted TCBs are skipped
- Assertions to check that nothing is written beyond core dump flash partition
add support for 32k XTAL as RTC_SLOW_CLK source
- RTC_CNTL_SLOWCLK_FREQ define is removed; rtc_clk_slow_freq_get_hz
function can be used instead to get an approximate RTC_SLOW_CLK
frequency
- Clock calibration is performed at startup. The value is saved and used
for timekeeping and when entering deep sleep.
- When using the 32k XTAL, startup code will wait for the oscillator to
start up. This can be possibly optimized by starting a separate task
to wait for oscillator startup, and performing clock switch in that
task.
- Fix a bug that 32k XTAL would be disabled in rtc_clk_init.
- Fix a rounding error in rtc_clk_cal, which caused systematic frequency
error.
- Fix an overflow bug which caused rtc_clk_cal to timeout early if the
slow_clk_cycles argument would exceed certain value
- Improve 32k XTAL oscillator startup time by introducing bootstrapping
code, which uses internal pullup/pulldown resistors on 32K_N/32K_P
pins to set better initial conditions for the oscillator.
Ref TW11683.
Ref https://esp32.com/viewtopic.php?f=13&t=1570
Fixes https://github.com/espressif/esp-idf/issues/337.
See merge request !696
- RTC_CNTL_SLOWCLK_FREQ define is removed; rtc_clk_slow_freq_get_hz
function can be used instead to get an approximate RTC_SLOW_CLK
frequency
- Clock calibration is performed at startup. The value is saved and used
for timekeeping and when entering deep sleep.
- When using the 32k XTAL, startup code will wait for the oscillator to
start up. This can be possibly optimized by starting a separate task
to wait for oscillator startup, and performing clock switch in that
task.
- Fix a bug that 32k XTAL would be disabled in rtc_clk_init.
- Fix a rounding error in rtc_clk_cal, which caused systematic frequency
error.
- Fix an overflow bug which caused rtc_clk_cal to timeout early if the
slow_clk_cycles argument would exceed certain value
- Improve 32k XTAL oscillator startup time by introducing bootstrapping
code, which uses internal pullup/pulldown resistors on 32K_N/32K_P
pins to set better initial conditions for the oscillator.
1.change the rowdata to rodata;
2.change BT_ACL_CONNECTIONS to Maximum BT/BLE connection count.
3. change the comments of bt_target.h:505 from 40 to 5.
wear levelling
This MR adds wear levelling component. It presents an interface similar to the interface of spi_flash and esp_partition. Inside, it stores data inside a partition to in a way that reduces worst case number of erase cycles for any given sector.
Also included are APIs similar to the ones provided for SDMMC to mount FAT filesystem on top of the wear levelling partition. A simple example shows how this API can be used.
Ref TW10338.
See merge request !567
- reorder directories listed in COMPONENT_SRCDIRS so that
subdirectories precede parent directories
- don’t include PPP source directories if PPP support is not enabled
1. close classic bt, can save 233k code size;
2. close smp module, can save 136k code size;
3. close gattc module, can save 24k code size;
4. close gatts module, can save 16k code size;
4. close the bluedroid stack log, can save 120k code size.
XTAL frequency detection, support for selecting XTAL frequency
This MR adds more robust XTAL frequency detection code (which gets run in the bootloader) and an option to set XTAL frequency in Kconfig. By default we still use autodetection, since it is more reliable than the one used in ROM code.
This will help with issues about XTAL frequency detection in high ambient temperature conditions.
Ref TW12008
See merge request !694
sdmmc: handle card removal when CD is not used
When SD card is removed during transaction, SDMMC peripheral can report
a range of errors, such as timeouts, CRC errors, start/end bit errors.
Under normal conditions (card is inserted), SDMMC peripheral also generates
command done or data done interrupts. When the card is removed, such
interrupts may not be always generated.
This change fixes handling of timeout interrupts and SBE interrupts.
It also adds a one second timeout into the event processing loop. This
timeout allows applications to recover in cases when the SDMMC peripheral
doesn’t generate command/data done event on card removal.
Fixes TW11592.
See merge request !678
fat/sdmmc: unmount FATFS object on error
Failure to call f_mount(NULL,...) makes FATFS attempt to clean up the old
FS object upon next mount. If previous mount operation has failed, some
parts of FS object may not be fully initialized, which will cause errors
(such as attempting to delete a mutex which wasn’t allocated).
Fixes TW11594.
See merge request !679
ROM code already implements XTAL frequency detection, but it uses the 8M
clock before the clock tuning parameters are initialized. With the
zero clock tuning parameter, 8M clock has significant frequency deviation
at high temperatures, which can lead to erroneous detection of 40 MHz
crystal as a 26 MHz one.
This change adds XTAL frequency detection code to rtc_clk_init routine,
and detection is performed after the 8M clock tuning parameter as been
initialized.
lwip: fix tcp stable test abort issue
This MR covers following changes:
1. Modify dhcp server timer to 1 seconds
2. Enable ETHARP_TRUST_IP_MAC. Consider following scenario: we are in throughput test or traffic stability test, if this option is disabled, then every 5 minutes, the IP/MAC entry in arch cache is aged out, however, the traffic continuously send to lwip from application, because there is no IP/MAC entry in ARP cache, then the packets have to be buffered in ARP queue and a ARP request is triggered, but the ARP queue can only holds 3 packets, the later packets will be dropped, then if the traffic is big, a lot of packets will be dropped here before we get the right ARP response. For TCP, this will trigger re-transmit, it's intolerable for some application, such as real time audio, if re-transmit happen, then performance of voice will be impact. For UDP, sometimes it may also cause problem, such as DHCP, if here we failed to send the DHCP here, we has to wait the DHCP timeout etc... so this option is enabled here by default.
See merge request !681
esp32: update wifi lib for limitting dynamic wifi buffer
Add limit for all dynamic wifi ebuf to avoid wifi run out of memory in some extreme scanrio.
The default max allocated dynamic tx buffer is 32
The default max allocated dynamic rx buffer is 64, make default value is bigger because when all packets we received are small packets, e.g. the length is 64Bytes, then 64K can hold 1000 packets, so 64 maybe a good candidate default value, anyway the customer can configure it via menuconfig.
The default dynamic wifi internal long/long-long mgmt is 32, generally 32 is enough for mgmt packet (beacon/auth/assoc/probe/null etc). Generally when all the 32 mgmt buffer is run out of memory, it means internal wifi state machine may has problem, we need to debug it.
See merge request !683
There are some RODATAs of libphy.a that are called in ISR. So need
to put them into DRAM to avoid access them when R/W SPI flash. Due
to the RODATAs which are called in ISR haven't been picked out to
put into DRAM, put all of the RODATA of libphy.a into DRAM. This
will be optimized in the future.
soc: allow REG_SET_FIELD to be used for bit fields
- Fixes an issue with `rtc_clk_apll_enable`: https://esp32.com/viewtopic.php?f=13&t=1673
- Fixes `rtc_clk_fast_freq_set` function always selecting XTAL/4 as fast clock source.
- Fixes regression in deep sleep current (7uA instead of 5uA).
See merge request !674
rtc_clk_init: handle case when XTAL frequency has already been set
On first reset, ROM code writes the estimated XTAL frequency into
RTC_APB_FREQ_REG (aka STORE5). If the application doesn’t specify exact
XTAL frequency (which is always the case for now), rtc_clk_init will
guess what kind of XTAL is used (26M or 40M), based on the estimated
frequency. Later, detected frequency is written into RTC_XTAL_FREQ_REG
(aka STORE4).
When the application switches clock source to PLL, APB frequency changes
and RTC_APB_FREQ_REG is updated. If the application encounters an RTC
WDT reset, RTC_APB_FREQ_REG will not be updated prior to reset. Once the
application starts up again, it will attempt to auto-detect XTAL
frequency based on RTC_APB_FREQ_REG, which now has value of 80000000.
This will fail, and rtc_clk_xtal_freq_estimate will fall back to the
default value of 26 MHz. Due to an incorrect XTAL frequency, PLL
initialization will also take incorrect path, and PLL will run at a
different frequency. Depending on the application this may cause just
garbage output on UART or a crash (if WiFi is used).
This change checks if RTC_XTAL_FREQ_REG has already been set before trying
to estimate XTAL frequency based on the value of RTC_APB_FREQ_REG, and
uses RTC_XTAL_FREQ_REG value if it is valid.
Fixes TW11738.
See merge request !691
Base MAC address can be stored in default manufacture-defined or customer
pre-defined place in EFUSE and other place e.g. flash or EEPROM.
If choose to use base MAC address which is stored in other place, please
call esp_base_mac_addr_set_external() before initializing WiFi/BT/Ehternet.
On first reset, ROM code writes the estimated XTAL frequency into
RTC_APB_FREQ_REG (aka STORE5). If the application doesn’t specify exact
XTAL frequency (which is always the case for now), rtc_clk_init will
guess what kind of XTAL is used (26M or 40M), based on the estimated
frequency. Later, detected frequency is written into RTC_XTAL_FREQ_REG
(aka STORE4).
When the application switches clock source to PLL, APB frequency changes
and RTC_APB_FREQ_REG is updated. If the application encounters an RTC
WDT reset, RTC_APB_FREQ_REG will not be updated prior to reset. Once the
application starts up again, it will attempt to auto-detect XTAL
frequency based on RTC_APB_FREQ_REG, which now has value of 80000000.
This will fail, and rtc_clk_xtal_freq_estimate will fall back to the
default value of 26 MHz. Due to an incorrect XTAL frequency, PLL
initialization will also take incorrect path, and PLL will run at a
different frequency. Depending on the application this may cause just
garbage output on UART or a crash (if WiFi is used).
SPI transfer length is bits, not bytes, so the error should indicate bits. Also, there are separate lengths for rx and
tx (confusingly named rxlength and length... if rxlength is 0, length is used). The code checks the tx length for the
rx, so it never validates rxlength.
Originally contributed as part of #511https://github.com/espressif/esp-idf/pull/511
Since mbedtls_net_errno is reset by fcntl, it is reset after calling
net_would_block, so the call to mbedtls_net_errno in mbedtls_net_recv
and mbedtls_net_send will always get back 0. This change propagates
the value returned by mbedtls_net_errno up through net_would_block,
to allow the correct error value to be used and avoid a redundant
call to mbedtls_net_errno.
Merges PR #511https://github.com/espressif/esp-idf/pull/511
Failure to call f_mount(NULL,...) makes FATFS attempt to clean up the old
FS object upon next mount. If previous mount operation has failed, some
parts of FS object may not be fully initialized, which will cause errors
(such as attempting to delete a mutex which wasn’t allocated).
When SD card is removed during transaction, SDMMC peripheral can report
a range of errors, such as timeouts, CRC errors, start/end bit errors.
Under normal conditions (card is inserted), SDMMC peripheral also generates
command done or data done interrupts. When the card is removed, such
interrupts may not be always generated.
This change fixes handling of timeout interrupts and SBE interrupts.
It also adds a one second timeout into the event processing loop. This
timeout allows applications to recover in cases when the SDMMC peripheral
doesn’t generate command/data done event on card removal.
Remove ESP_EARLY_LOGI before bss is initialized; it crashes the CPU
There's an ESP_EARLY_LOGI line that can get called before the BSS is initialized; the early logging code doesn't cope well with that: it checks if FreeRTOS is up, but the variables it uses for that contains garbage because it isn't cleared yet, giving the wrong result. The logging code then tries to set a mux, crashing the entire system. This patch removes the log line and adds a warning at the BSS initialization line not to do anything complex before that point.
Fixes https://github.com/espressif/esp-idf/issues/523
See merge request !671
- Implements application tracing module which allows to send arbitrary
data to host over JTAG. This feature is useful for analyzing
program modules behavior, dumping run-time application data etc.
- Implements printf-like logging functions on top of apptrace module.
This feature is a kind of semihosted printf functionality with lower
overhead and impact on system behaviour as compared to standard printf.
component/bt: transfer bluedroid timer events to be handled by BTC task
NVS operation can take long time for timer task to handle. Transfer the alarm event to be handled by BTC task.
See merge request !670
Detect invalid cache access
This MR adds always-on feature which detects cache invalid access and triggers panic handler when invalid access interrupt is raised.
See merge request !660
Confusion here is that original ROM has two functions:
* SPIReadModeCnfig() - sets mode, calls enable_qio_mode/disable_qio_mode
* SPIMasterReadModeCnfig() - As above, but doesn't set QIO mode in status register
However we never want to use the ROM method to set/clear QIO mode flag, as not all flash chips work this way. Instead we
do it in flash_qio_mode.c in bootloader.
So in both cases (ROM or "patched ROM") we now call SPIMasterReadModeCnfig(), which is now named
esp_rom_spiflash_config_readmode().
Fix uart tx function block issue
To enable tx empty interrupt each time the tx ringbuffer get filled, so that tx function will not block if tx data length is larger than tx ringbuffer size.
Reported from customer of Audio team.
See merge request !658
give the AP and STA netifs different names for ease of debugging lwip
Both AP and STA netifs used to be called "en". This changes the name to "st" for STA and "ap" for AP.
Ref https://github.com/espressif/esp-idf/pull/456.
See merge request !653
Feature/btdm avrc
The source branch "feature/btdm_avrc" includes classic Bluetooth profiles A2DP(sink role) and AVRCP(controller role);
Menuconfig options to control whether to enable classic BT is added.
See merge request !591
Enable checks for encrypted flash in OTA
Even if firmware is compiled without CONFIG_FLASH_ENCRYPTION_ENABLED.
Rationale: CONFIG_FLASH_ENCRYPTION_ENABLED controls whether boot loader generates keys for encryption or not, but flash encryption can be configured externally. With this change, it's possible to have boot loader not generate keys but still have encryption working.
Also fix use of it->part
Ref. https://github.com/espressif/esp-idf/pull/453
See merge request !647
To enable tx empty interrupt each time the tx ringbuffer get filled, so that tx function will not block if tx data length is larger than tx ringbuffer size.
Reported from customer of Audio team.
bt component: Fix memory leak while using gatt server
- fix memory leak while creating attribute table
- fix memory leak while deleting service
See merge request !656
Introduce soc component, add source of rtc_clk and rtc_pm libraries
This MR adds parts of the RTC library source code (initialization, clock selection functions, sleep functions). WiFi-related power management functions are kept inside the precompiled library. Most of RTC library APIs have been renamed.
Default CPU frequency option in Kconfig is set to 160MHz, pending qualification of 240MHz mode at high temperatures.
Register header files are moved into the new soc component, which will contain chip-specific header files and low-level non-RTOS-aware APIs (such as rtc_ APIs). Some of the files from ESP32 component were also moved: cpu_util.c, brownout.c, and the corresponding header files. Further refactoring of ESP32 component into more meaningful layers (chip-specific low level functions; chip-specific RTOS aware functions; framework-specific RTOS-related functions) will be done in future MRs.
See merge request !633
Bugfix/flash busy check wait spi idle
This branch moves some ROM SPI flash driver to IDF to fix bug in Wait_SPI_Idle() function.
Also it applies code style rules of IDF to integrated ROM driver sources.
See merge request !584
Even if firmware is compiled without CONFIG_FLASH_ENCRYPTION_ENABLED
Rayionale: CONFIG_FLASH_ENCRYPTION_ENABLED controls whether boot loader
generates keys for encryption or not, but flash encryption can be
configured externally. With this change, it's possible to have boot
loader not generate keys but still have encryption working.
Also fix use of it->part
1) fixed SPI_read_status: added check for flash busy flag in matrix mode
2) fixed SPI_page_program: enable write before writing data to SPI FIFO
3) SPI flash ROM funcs replacement is controlled via menuconfig option
CI: add reset between running each unit test cases
Unit test is designed to detect bug **within** each test case. Therefore we'll reset between each case to provide a clean context. We will later add stress cases to run unit test cases together to detect potential bugs.
See merge request !636
esp32: initialize cross-core interrupt in single core mode
The software interrupt originally used as the cross-core interrupt is
now also used to yield from a FreeRTOS critical section; therefore it
must be initialized for single core mode as well.
Fixes https://github.com/espressif/esp-idf/issues/496
See merge request !640
fix warnings generated by ESP_ERROR_CHECK(variable) in release builds
This uses the same pattern as “assert” in release builds to silence the
warning. At the same time, we make sure that if a statement is wrapped
into ESP_ERROR_CHECK, it is executed in release build as well.
Fixes https://github.com/espressif/esp-idf/issues/497
See merge request !641
This uses the same pattern as “assert” in release builds to silence the
warning. At the same time, we make sure that if a statement is wrapped
into ESP_ERROR_CHECK, it is executed in release build as well.
The software interrupt originally used as the cross-core interrupt is
now also used to yield from a FreeRTOS critical section; therefore it
must be initialized for single core mode as well.
Fixes https://github.com/espressif/esp-idf/issues/496
esp32: RWDT is used to reboot system in case of panic handler crash
This branch uses RWDT to reboot system in case of panic handler crash.
See merge request !625
Feature/btdm uart hci
1. support UART HCI, devolper need not to make a bridge between VHCI and UART.
2. fix bug of rand/srand called in ISR.
3. fix bug of BLE rx packets may cause assert.
See merge request !626
component/bt : modify alarm APIs to be safely accessible from multiple tasks
Improve the osi_alarm module to make the alarm APIs become thread safe.
See merge request !570
1. support UART HCI, devolper need not to make a bridge between VHCI and UART.
2. fix bug of rand/srand called in ISR.
3. fix bug of BLE rx packets may cause assert.
lwip: implement lwip critical session with mutex
Currently lwip critical session is based on interrupt, now replace it with mutex
See merge request !595
spi_flash: fix race condition in s_flash_op_complete access
Flash operation complete flag was cleared by the CPU initiating flash operation. If the other core was running an ISR, then IPC task could be late to enter the loop to check `s_flash_op_complete` by the time next flash operation started. This would cause a deadlock, as the IPC task would still be waiting for `s_flash_op_complete` to be set (which was already cleared by the next flash operation), while the flash operation task would be blocked waiting for IPC task to set `s_flash_op_can_start`.
If the flag is cleared on the CPU waiting on this flag, then the race condition can not happen.
See merge request !615
Fix timing adjustment needed for higher speeds of SPI master bus.
Ref https://github.com/espressif/esp-idf/issues/363 . It was found out the master SPI driver didn't exactly calculate the delay compensation needed, breaking 20 and 26MHz full-duplex mode. This fixes these use cases. We also found out 40MHz full-duplex routed over the GPIO matrix does not work because of a hardware quirk; this MR adds a check/error for that case until we find a workaround.
See merge request !547
If static tx buffer is selected, WiFi tx buffers are allocated when WiFi is initialized and released
when WiFi is de-initialized. If dynamic tx buffer is selected, WiFi tx buffer is allocated when tx
data is delivered from LWIP to WiFi and released when tx data is sent out by WiFi.
The size of each static tx buffers is fixed to about 1.6KB and the size of dynamic tx buffers is
depend on the length of the data delivered from LWIP.
If PSRAM is enabled, "STATIC" should be selected to guarantee enough WiFi tx buffers.
If PSRAM is disabled, "DYNAMIC" should be selected to improve the utilization of RAM.
Fix finding location of ISR stack space for CPU1
Up to now, the CPU1 interrupts erroneously used the area *after* the ISR stack region, leading to bugs in BT Classic. This fixes that.
See merge request !618
Flash operation complete flag was cleared by the core initiating flash
operation. If the other core was running an ISR, then IPC task could
be late to enter the loop to check s_flash_op_complete by the time next
flash operation started. If the flag is cleared on the CPU waiting on
this flag, then the race condition can not happen.
ULP coprocessor toolchain integration
- build system support for ULP coprocessor toolchain
- documentation for ULP coprocessor instruction set
- documentation for ULP code execution flow, loading programs, exchanging data
- example: counting pulses using ULP
See merge request !394
Reset WIFI mac when wifi start and update wifi lib
1. reset wifi mac when wifi start
2. roll back rx hung workaround for beacon timeout
3. fix amsdu ap interface wrong issue
4. fix amsdu header parse error
5. fix amsdu flag wrong issue
6. PHY: V350, fix BT rssi bug
7. RTC: V225, fix bt will be not work when wifi is reset
See merge request !606
SPI flash operations lock for shorter periods
Based on bug report here:
https://esp32.com/viewtopic.php?f=13&t=1489&p=6816#p6773
Long SPI flash erase (and possibly write/read) cycles block all tasks on both CPUs for an extended period, and can lead to WiFi dissassociation (and general priority inversion.)
This MR inserts preemption breaks into large operations (all erases, writes every 8KB, reads every 16KB).
Overhead of a single spi_flash_guart_start()/spi_flash_guard_end() cycle measured at approx 67us (assuming no preemption.)
See merge request !600
bugfix: ESP32 Core Dump reported issues
This MR fixes the following issues:
1. fixed path to esptool when there is no compiled python module for it
2. GDB inernal failure handling was added
See merge request !599
Error handling in NVS initialization
Previously nvs_flash_init worked under an assumption that there should always be at least one free page available. This is true during normal operation, but in some cases (such as when changing application partition table from a non-OTA to an OTA one), NVS partition may get truncated, which will cause empty pages to be lost.
This MR adds error checks for this condition, and updates code which calls `nvs_flash_init` to check for the return code.
For most examples, a simple `ESP_ERROR_CHECK` is added around `nvs_flash_init`. For NVS examples and the OTA example, more robust error handling is added.
This change also removes nvs_flash_init calls from examples which don't use NVS.
See merge request !582
idf_monitor: Small fixes (baud rate, EOL, /dev/tty.X on macOS, Ctrl-T on failure)
* "make monitor" now passed the configured baud rate.
Closes#436https://github.com/espressif/esp-idf/issues/436
* Pass toolchain prefix from sdkconfig into monitor tool
* Allow setting EOL in idf_monitor.py, use CRLF by default
* Detect if /dev/tty.X is used on macOS, warn and replace with /dev/cu.X
* If a build fails or gdb exits, ignore Ctrl-T (allowing Ctrl-T Ctrl-A/F to be same key sequence everywhere)
* Add a note about winpty on Windows.
Ref 02fdf8271d (commitcomment-21369196)
* Fix problems with Console.cancel() not existing in older pyserial
* Print more user-friendly symbols for "start of iram" and "start of flash"
See merge request !594
1. reset wifi mac when wifi start
2. roll back rx hung workaround for beacon timeout
3. fix amsdu ap interface wrong issue
4. fix amsdu header parse error
5. fix amsdu flag wrong issue
6. PHY: V350, fix BT rssi bug
7. RTC: V225, fix bt will be not work when wifi is reset
* Erase range operations allow preemption after each block or sector.
* Write operations allow preemption every 8KB of data.
* Reado operations allow preemption every 16KB of data.
This is to avoid confusion when idf_monitor prints the first symbol in each section, ie "WindowOverflow4" or similar,
when bootloader prints the section mapping address.
Closes#447https://github.com/espressif/esp-idf/issues/447
* "make monitor" not passed the configured baud rate
Closes#436https://github.com/espressif/esp-idf/issues/436
* Pass toolchain prefix from sdkconfig into monitor tool
* Allow setting EOL in idf_monitor.py, use CRLF by default
* Detect if /dev/tty.X is used on macOS, warn and replace with /dev/cu.X
* If a build fails or gdb exits, ignore Ctrl-T (allowing Ctrl-T Ctrl-A/F to be same key sequence everywhere)
* Add a note about winpty on Windows
Ref 02fdf8271d (commitcomment-21369196)
modify touch pad read function
The touch pad read function taks too much time within spin lock waiting for the "done bit". (about 7.6ms as we tested)
So we try to use a mutex on the touch read function and any other functions might change the "done bit".
See merge request !543
This issue is reported from https://github.com/espressif/esp-idf/issues/304.
We found that when we operate the hw command registers in I2C struct, sometimes the behaviour would be different in DEBUG/RELEASE optimisation level:
The code looks like this:
I2C[i2c_num]->command[p_i2c->cmd_idx].byte_num -= 0;
In DEBUG configuration:
I2C[i2c_num]->command[p_i2c->cmd_idx].byte_num -= 0;
400f3ab0: 3388 l32i.n a8, a3, 12
400f3ab2: 14c882 addi a8, a8, 20
400f3ab5: a08840 addx4 a8, a8, a4
400f3ab8: 0020c0 memw
400f3abb: 2898 l32i.n a9, a8, 8
400f3abd: 0020c0 memw
400f3ac0: 28b8 l32i.n a11, a8, 8
400f3ac2: 74a090 extui a10, a9, 0, 8
400f3ac5: 00af92 movi a9, 0xffffff00
400f3ac8: 109b90 and a9, a11, a9
400f3acb: 2099a0 or a9, a9, a10
400f3ace: 0020c0 memw
400f3ad1: 2899 s32i.n a9, a8, 8
In RELEASE configuration:
I2C[i2c_num]->command[p_i2c->cmd_idx].byte_num -= 0;
400f2ba2: 580572 l8ui a7, a5, 88
400f2ba5: 747070 extui a7, a7, 0, 8
400f2ba8: 0020c0 memw
400f2bab: 584572 s8i a7, a5, 88
Looks like the compiler will make it a 8bit operation after optimisation.
But the register value changes from 0x901 to 0x101.
After this 8-bit optimisation, the 11th bit changed from 1 to zero, which caused this error.
We are still trying to find out why that happens, because there might be some risk when operating the register struct.
This is a workaround to avoid "-=" operation on I2C register struct fields.
1. Add low speed channels for LEDC module.
2. Improve fade object allocate mechanism.
3. Improve ledc example, add 2 low speed channels in example.
4. Remove debug code
5. Improve the register bit field name of slow clock.
esp32: update wifi lib for some bugfix/features
1. add options to disable nvs
2. add station keepalive with softap
3. fix beacon rx start time not accurate issue
4. set wifi rx desc/buffer boundary check to internal memory boundary
See merge request !578
nvs_flash_init may return an error code in some cases, and applications
should check this error code (or at least assert on it being ESP_OK, to
make potential issues more immediately obvious).
This change modifies all the examples which use NVS to check the error
code. Most examples get a simple ESP_ERROR_CHECK assert, while NVS
examples, OTA example, and NVS unit tests get a more verbose check which
may be used in real applications.
Expand 'make monitor' support
New 'make monitor' idf_monitor tool for better monitor output. Running 'make monitor' will now:
* Automatically look up code addresses via addr2line and print function, source file, line number in terminal.
* Can reset the ESP32 by typing Ctrl-T Ctrl-R.
* Can run "make flash" by typing Ctrl-T Ctrl-F.
* Can run "make app-flash" by typing Ctrl-T Ctrl-A.
* If gdb stub starts, monitor will automatically run gdb and connect. When gdb exits, ESP32 resets and monitor resumes.
* Exit is still Ctrl-[
Have some more features I'd like to add (log output to file, crash dump support) but I think this is at the point of being useful.
See merge request !565
This change adds a check for the free page count to nvs_flash_init.
Under normal operation, NVS keeps at least one free page available,
except for transient states such as freeing up new page. Due to external
factors (such as NVS partition size reduction) this free page could be
lost, making NVS operation impossible. Previously this would cause an
error when performing any nvs_set operation or opening a new namespace.
With this change, an error is returned from nvs_flash_init to indicate
that NVS partition is in such a state.
make: don’t override TEST_COMPONENTS
When idf_monitor is launched from make, it gets modified `TEST_COMPONENTS`
variable which contains full paths to the test components instead of the
names. This causes `TEST_COMPONENT_PATHS` to be empty and the unit test
app gets built without any test components.
This change introduces an internal `TEST_COMPONENTS_LIST` variable which
gets set either from `COMPONENTS` if `TESTS_ALL` is 1, or from
`TEST_COMOPONENTS` otherwise.
Bootloader makefile is also fixed to avoid propagating `TESTS_ALL` to the
bootloader build step.
See merge request !569
bug fix: fix uart data bug when stop-bit is set as 2-bit mode
This is a workaround for a hardware bug.
When we want to use 2-stop-bit mode, we need to set stop-bit-1 and set dl1_en in rs485 register.
See merge request !544
1. add options to disable nvs
2. add station keepalive with softap
3. fix beacon rx start time not accurate issue
4. set wifi rx desc/buffer boundary check to internal memory boundary
The touch pad read function taks too much time within spin lock waiting for the "done bit". (about 7.6ms as we tested)
So we try to use a mutex on the touch read function and any other functions might change the "done bit".
When idf_monitor is launched from make, it gets modified TEST_COMPONENTS
variable which contains full paths to the test components instead of the
names. This causes TEST_COMPONENT_PATHS to be empty and the unit test
app gets built without any test components.
This change introduces an internal TEST_COMPONENTS_LIST variable which
gets set either from $(COMPONENTS) if TESTS_ALL is 1, and from
TEST_COMOPONENTS otherwise.
Bootloader makefile is also fixed to avoid propagating TESTS_ALL to the
bootloader build step.
bt component: fix bluetooth gatt packets process bugs
1. Add process of prepare write request packets
2. Add process of execute write request packets
3. Add process of reliable write request packets
4. Fix bug of processing read blob request packets
5. Fix bug of processing write request packets
6. Optimize error check and process in stack
See merge request !558
add wakeup from touch sensor, and deep sleep example
- add new deep sleep wakeup mode
- change documentation to explain incompatibilities between different wakeup mode, add error checks
- add new ULP instructions necessary for ULP wakeup scenario
- fix issues with I_WR_REG, I_SLEEP, I_END instructions
- add deep sleep example, illustrating the use of timer, gpio, touch, and ULP wakeup triggers
See merge request !461
add extra check before bluedroid init and disable
add extra check before bluedroid init and disable to avoid the mixed call cause unexpected errors.
See merge request !553
component/bt: optimize stack size of Bluetooth Tasks and make them be configurab…
Bluetooth tasks' stack size are optimized and can be configured by the CONFIG_NEWLIB_NANO_FORMAT option.
See merge request !559
esptool version bump and new "espefuse.py set_flash voltage" command
* New "espefuse.py set_flash_voltage" command to easily set a fix
VDD_SDIO regulator voltage (1.8V, 3.3V or disabled).
* Fixes bugs when flashing files with non-4-byte aligned lengths
(doesn't effect esp-idf image files)
* esptool README improvements
* Detect overlapping files in write_flash
* read_mac now works correctly on ESP32
* Integrates reset fix for older dev boards (formerly the "Windows ESP32R0 reset workaround")
See merge request !481
Change max number of open sockets
Change max number of open sockets from 16 to 32 because of MFI project need support 21 open sockets at least.
See merge request !532
1. Add process of prepare write request packets
2. Add process of execute write request packets
3. Add process of reliable write request packets
4. Fix bug of processing read blob request packets
5. Fix bug of processing write request packets
6. Optimize error check and process in stack
Fix partition- and mmap-related issues
- Fix unit tests failing to start up due to a mismatch between sdkconfig flash size and size required by partition table.
- Fix a bug that partition APIs loaded the partition table in reverse order. As such, `esp_partition_next` and `esp_partition_find_first` did not work as expected. Add a test.
- Update the workaround for stale cache reads issue: do Cache_Flush for non-encrypted flash as well. Add a test.
See merge request !555
The issue that cache entries are not invalidated correctly sometimes
can also be reproduced for non-encrypted flash as well.
This change updates the workaround to do Cache_Flush, enabling it for
non-encrypted flash, and adds a unit test.
- change order of assert arguments to (expected, actual)
- set expected partition count to 3 to match the new partition table
- use the new get_test_partition facility
- check that partitions are listed in correct order
- remove leftover debugging printfs
