Bugfixes:
- Fix http url redirection issue
- Fix basic/digest auth issue with http url
Features:
- Add support for adding custom http header
- Add support for reading firmware image header
- Add support for monitoring upgrade status
- This requires breaking down esp_https_ota API such that it allows finer application level control
- For simpler use-cases previous API is still supported
Closes https://github.com/espressif/esp-idf/issues/3218
Closes https://github.com/espressif/esp-idf/issues/2921
There was existing support for adding authorization info in esp_http_client
but it was functional only while using `esp_http_client_perform` API. This commit just moves
existing authorization addition logic into publicly exposed API.
Acquires PM_APB_FREQ_MAX lock when carrying any transaction on I2S if
Power Management Framework is enabled.
Signed-off-by: Sachin Parekh <sachin.parekh@espressif.com>
Acquires PM_APB_FREQ_MAX lock when carrying any transaction on I2C if
Power Management Framework is enabled.
Signed-off-by: Sachin Parekh <sachin.parekh@espressif.com>
1. add kconfig help for GPIO0 output mode
2. fix a bug when select gpio0 output mode and initialize psram
3. make default config to official development board
4. fix wrong LAN8720 register index
Previous version read all data to the buffer including header which reduced maximum payload read. This version uses a local array to receive header and reads payload bytes to the buffer
cherry-picked from db121a56e1
1.Fix the bug that WiFi stop leads to task watchdog(526c6956)
2.Fix the WiFi init sequence bug
3.Fix smartconfig ipc crash
4.Put g_promis_buf to IRAM
5.esp_wifi_set_channel should return error when sniffer is not enabled
6.fix the bug when set WEP authmode or wrong authmode, there is no error return
7.fix the bug that STA parse authmode wrong when AP sets WPA_WPA2_PSK mode
8.fix the bug that wrong error code and wrong event when there is an auto AP in multi-ssid case
- Backport(v3.3) of IDF MR!6122
- Modifies `smp_utils.c` to add check on encryption key size received from
peer.
- Modifies `esp_ble_gap_set_security_param` API to add minimum encryption key
size requirement.
Remove xtensa/xruntime.h
Fix sending Lmp_feature_req_ext in a loop
Fix 2 bugs in r_ld_fm_sket_isr
fix data loss and send same pkt twice sometimes
fix adv data error in air sometimes
fix adv start/stop crash sometimes
Fix connect fail with some speakers
clear BT/BLE interruots after controller disable
add sco_data_path to be set in sdkconfig and do not reset the value upon HCI reset command
1. modify the limit of frames to send to avoid dropping packet on A2DP source due to TX data queue overflow
2. reduce the A2DP source data queue size in order to achieve faster control respnonse
This MR is intended to fix incorrect parsing of HTTP requests when empty header values are present.
The issue is was due to asymmetric behavior of `http_parser` library, which in case of:
non-empty header values : invokes callbacks with the pointer to the start of a value
empty header values : invokes callbacks with pointer to the start of next header or section
Since HTTP server relies on this pointer (along with length of the value) to locate the end of a value, and replace the line terminators (CRLFs) with null characters, the second case needed to be handled correctly.
Closes IDFGH-1539
Closes https://github.com/espressif/esp-idf/issues/3803
If httpd_sess_trigger_close() gets called twice for the same socket,
the first httpd_sess_close() cb closes the correct socket, but the second
invocation closes the wrong socket which was just accepted and added to
the socket db. Checking for the lru counter will help identify this as the
counter is set only for requests actually served.
We fixed some flash bugs in bootloader, but for the users used the old
vrsion bootloader, they can not fix these bugs via OTA, the solution is
add these updates in app startup.
These updates include:
1. SPI flash gpio matrix and drive strength configuration
2. SPI flash clock configuration
3. SPI flash read dummy configuration
4. SPI flash cs timing configuration
5. Update flash id of g_rom_flashchip
Hardware AES-CBC performance changes:
Release config 11.0MB/sec -> 10.8MB/sec
Debug config 9.4MB/sec -> 9.8MB/sec
(Unrolling the loop to optimize the check improves
performance at -Og, even with the fault check.)
Made MMU pages available check in `esp_image_format.c`
This now makes it possible to map and process bootoader image as well in chunks when image doesn't fit completely into available free pages.
Signed-off-by: Vikram Dattu <vikram.dattu@espressif.com>
There are lot of prints of `Allocate TX buffer for DMA`
Changed these from `ESP_LOGI` to `ESP_LOGD`
Signed-off-by: Vikram Dattu <vikram.dattu@espressif.com>
This problem may cause HCI send command timeout.
When host call VHCI api to do btdm_wakeup_request, then controller
wakeup process will be handled in ISR and controller task context.
As host task priority is lower than controller task and ISR,
it will cause an incorrect behavior that before VHCI take the
rx_flow_on_semaphore, controller sleep again, then VHCI cannot take
the semaphore and has to wait the automatic wakeup.
On flash program operation (either erase or write), if corresponding address has
cache mapping present then cache is explicitly flushed (for both pro and app cpu)
Closes https://github.com/espressif/esp-idf/issues/2146
These changes guarantee that the SSID and Passphrase received via protocomm are NULL terminated and size limited to their standard lengths.
List of changes:
* Corrected length of passphrase field in wifi_prov_config_set_data_t structure
* Performing length checks on SSID, passphrase and bssid, when populating wifi_prov_config_set_data_t structure with received credentials
1. resend eb which are pending in g_ic.tx_buf due to channel switch.
2. add lock for mgmg/xon/bcast to protect send from user flush.
3. softap: add check if secondary offset is correct when start softap.
4. softap: in inactive timer handler, add check if child bss is removed to avoid removing it again.
5. disable A-MPDU for non-root.
6. fix reusing a freed eb.
7. fix when node becomes root, it does not record assoc value to nvs.
8. discard unnecessary forwarded group packets.
9. fix toDS state is not updated in time.
10. fix s_sta_cnx_times is not cleared when deinit causes root sends ADD annoucement.
11. root: increase beacon timeout time from 6 seconds to 15 seconds to delay initiation of reconnection.
12. add esp_mesh_get_tsf_time to return TSF time.
13. send the whole routing table multi-times.
14. clear candidate settings if not receive candidate beacon within 8 seconds.
When flash work in DIO Mode, in order to ensure the fast read mode of flash
is a fixed value, we merged the mode bits into address part, and the fast
read mode value is 0 (the default value).
open_fn() was introduced in the context of HTTPS server, as a configurable callback function that is called by the HTTP server, on every newly created socket. It is responsible of allocating resources for per session transport security.
Earlier, if open_fn were to fail, the newly created socket would be closed by the server but the corresponding entry, for the now invalid socket, will remain in the internal socket database until that invalid socket is detected due to error when calling select(). Because of this delayed closing of sockets, the HTTPS server would quickly face shortage of available sessions when a lot of SSL handshake errors are happening (this typically occurs when a browser finds that the server certificate is self signed). This changes in this MR fix this issue by clearing up the socket from internal database, right after open_fn fails.
Closes https://github.com/espressif/esp-idf/issues/3479
List of changes in components/wifi_provisioning:
* Manager version is now v1.1
* .proto files and protocomm handler added for sending Wi-Fi scan command and receiving scan results
* Implemented handlers for wifi_scan protocomm endpoint
* Update manager context data structure to hold scan state and results
* scheme_softap now runs Wi-Fi in APSTA mode
* Wi-Fi is started in AP mode when provisioning is started. This is necessary for scan list to work
* Docs updates with information about new wifi_scan endpoint
List of changes in tools/esp_prov:
* Added functions for sending and receiving protobuf messages compatible with wifi_scan protocomm endpoint
* Added feature to display/refresh scan results and accept user selection at runtime
* New functions:
* get_version() : only returns the protocol version string
* has_capability() : check is a capability is present according to proto-ver response
* wifi_scan feature is provided only if the `wifi_scan` capability is present
Other changes:
* Replace recursive mutex with plain mutex
* assert on return value of mutex give / take calls
* replace all calls with macros ACQUIRE_LOCK and RELEASE_LOCK
* some checks added in scanning related private APIs
* free and nullify scanning context and state if service is stopped while ongoing scan
port*_CRITICAL_SAFE API calls port*_CRITICAL or port*_CRITICAL_ISR
depending on the context (Non-ISR or ISR respectively).
FREERTOS_CHECK_PORT_CRITICAL_COMPLIANCE Kconfig option added
Signed-off-by: Sachin Parekh <sachin.parekh@espressif.com>
xTaskIncrementTick have to unwind uxPendedTicks on CPU1 and CPU0.
Use case: If an erase operation was run on the CPU1 then it leads
to starving other tasks which waiting time. Waited tasks just skipped.
Closes: https://github.com/espressif/esp-idf/issues/1952
Closes: IDF-183
Fixed the case when the first part of log was missed
this was happened when:
* CONFIG_CONSOLE_UART_CUSTOM option is selected (UART1)
* The selected CONSOLE_UART port is used also for the console component
* in code esp_restart() or abort() functions were called.
List of changes:
* Use 128 bit characteristic UUIDs when creating GATT table entries
* Change primary service attribute value to 128 bit custom service UUID
* Use raw advertisement data to convey flags and 128 bit primary service UUID
* Use raw scan response to send device name as complete local name
* Increase maximum device name length in relation to maximum scan response length
* Set Characteristic User Description attributes for each characteristic to convey protocomm endpoint names
List of changes:
* Kconfig option HTTPD_LOG_PURGE_DATA enables logging of purged data
* Kconfig option HTTPD_PURGE_BUF_LEN sets purge buffer length
* Purged data is logged in hex
Closes https://github.com/espressif/esp-idf/issues/3359
Fix following wpa2 enterprise vulnerability issues:
1. The station can complete 4-way handshake after EAP-FAIL is received
2. The station crashes if EAP-SUCCESS is received before PMK is setup
Issue is that when users creates a custom bootloader from
$IDF_PATH/components/bootloader. Parent project build uses the copy but
bootloader subproject build uses the original still. The issue is solved
by passing the custom bootloader as extra component directory so
bootloader build knows to use the new copy (itself) in the build.
This prevents a device from being bricked in case when both secure boot & flash encryption are enabled and encryption gets interrupted during first boot. After interruption, all partitions on the device need to be reflashed (including the bootloader).
List of changes:
* Secure boot key generation and bootloader digest generation logic, implemented inside function esp_secure_boot_permanently_enable(), has been pulled out into new API esp_secure_boot_generate_digest(). The enabling of R/W protection of secure boot key on EFUSE still happens inside esp_secure_boot_permanently_enable()
* Now esp_secure_boot_permanently_enable() is called only after flash encryption process completes
* esp_secure_boot_generate_digest() is called before flash encryption process starts
