This will be useful if a webserver is already running and the application
does not want protocomm to start a new instance.
Signed-off-by: Piyush Shah <piyush@espressif.com>
Currently, only erase operation performed by the application leads
to detection of NVS key partition as uninitialised. This change
adds additional checks for detecting partition as uninitialised,
when device boots first time right after encryption by bootloader.
Fix following WiFi bugs:
1. Fix a crash bug which is caused by WiFi static TX buffer alloc/free.
2. Fix the bug that iphone fails to connect to ESP32 AP by enabling AP BAR receiving.
3. Fix the bug that ESP32 station fails to connect some APs, such as Xiaomi hotspot etc,
after reset.
1. Cleanup the README of app_trace_to_host example based on the template.
2. Remove unused header files in the example.
3. Fix typos in public header file.
Files where stack protector is initialized should not be compiled with
stack protector enabled. This was done for Make but missing for CMake.
Fixes https://github.com/espressif/esp-idf/issues/2990.
Shortcircuit evaluation may cause skip of _mdns_strdup_check of any further question field, which after clear_rx_packet freed undefined memory.
Fixes https://ezredmine.espressif.cn:8765/issues/28465
This commit adds the ability for backtracing to trace from the itnerrupt to the
task stack, and across nested interrupts. Test cases have also been added.
New unit tests added
------------------------
**Local:** Local test uses the GPIO matrix to connect the master and the
slave on the same board. When the master needs the iomux, the master
uses the GPIOs of its own, the slave connect to the pins by GPIO matrix;
When the slave needs the iomux, the slave uses the GPIOs of its own, the
master connects to the pins by GPIO matrix.
- Provide a new unit test which performs freq scanning in mode 0. It
scans frequency of 1M, 8M, 9M and all frequency steps up to the maximum
frequency allowed.
**M & S**: Master & slave tests performs the test with two boards. The
master and slave use iomux or gpio matrix according to the config.
- Provide a new unit test which performs freq scanning in mode 0. It
scans frequency of 1M, 8M, 9M and all frequency steps up to the maximum
frequency allowed.
- Provide a new unit test which performs mode test with significant
frequencies. It tests mode 0,1,2,3 with low frequency, and the maximum
frequency allowed.
Paremeterized Test Framework
-----------------------------
The SPI has a lot of parameters, which works in the same process.
This framework provides a way to easily test different parameter sets.
The framework can work in two different ways:
- local test: which requires only one board to perform the test - master
& slave test: which generates two sub test items which uses the same
config set to cooperate to perform the test.
The user defines a (pair if master/slave) set of init/deinit/loop
functions. Then the test framework will call init once, then call loop
several times with different configurations, then call deinit.
Then a unit test can be appended by add a parameter group, and pass it into
a macro.
1. during parent selection, when scanning a MAP without ext-assoc IE, it will be handled as it has the same router BSSID as itself.
2. for MAP, when its client leaves, always post SYSTEM_EVENT_AP_STADISCONNECTED to mesh layer regardless of whether the client has passed the encrypted authentication or not.
Originally, when doing BLE active scan, Bluedroid will not report adv to
application layer until receive scan response. This option is used to
disable the behavior. When enable this option, Bluedroid will report
adv data or scan response to application layer immediately.
The following 2 compiler warnings are only reproducible when setting:
OPTIMIZATION_FLAGS = -Ofast
esp-idf/components/soc/esp32/rtc_clk.c:
In function 'rtc_clk_cpu_freq_get':
esp-idf/components/soc/esp32/rtc_clk.c:506:12:
error: 'freq' may be used uninitialized in this function
[-Werror=maybe-uninitialized]
return freq;
esp-idf/components/esp_ringbuf/ringbuf.c:
In function 'xRingbufferReceiveSplitFromISR':
esp-idf/components/esp_ringbuf/ringbuf.c:934:26:
error: 'pvTempTailItem' may be used uninitialized in this function
[-Werror=maybe-uninitialized]
*ppvTailItem = pvTempTailItem;
Closes https://github.com/espressif/esp-idf/pull/2878
1. add support for ESP32 DTE
2. add support for SIM800/BG96 DCE
3. add PPPoS setup procedure
4. add support for SMS
5. add mqtt example after PPP connection established
Previously, hardware SHA engine "locks" were mutex semaphores. This meant that the task which
started a particular SHA session (in hardware) needed to finalise that session, or an invalid
FreeRTOS state was created.
Replace with binary semaphore which can be shared between tasks.
Includes a unit test, but unit test doesn't crash even without this fix
(some other unknown condition is required).
Due to a hardware limitation in ESP32, the first four bytes of some
CSI data is invalid, not the last four bytes.
Correct a mistake of CSI sub-carrier index in documentation.
Bootloader used to calculate the number of cache pages assuming that
load address was aligned, while in reality load address for DROM and
IROM was offset by 0x20 bytes from the start of 64kB page. This
caused the bootloader to map one less page if the size of the image
was 0x4..0x1c less than a multiple of 64kB.
Reported in https://esp32.com/viewtopic.php?f=13&t=6952.
1. detect and fix root conflicts when router BSSID is not set.
2. when root can not connect to the router due to NO_MORE_STAS(reason code:5), root will stop re-connection and perform MESH_NWK_LOOK_FOR_NETWORK.
3. wifi: fix the disconnection caused by receiving a deauth frame from non-parent node during scanning.
4. fix routing table redundant issue.
5. modify the max routes limitation from 300 to 1000.
6. wifi: fix ap does not deauth sta which has not completed the 4-way handshake.
Note : In future consider deprecating usage of -1 for setting
buffer length equal to string length in APIs httpd_resp_send()
and httpd_resp_send_chunk()
1. fix error when fading is too fast
2. fix error when setting duty and update immediately
3. update register header file to be in accord with TRM
closes https://github.com/espressif/esp-idf/issues/2903
esp-idf/components/freemodbus/modbus_controller/modbus_controller.c: The MB_INST_MAX_SIZE is changed to max value=(65535*2);
Update support for coils read into freemodbus.c;
TW#28143
Closes https://github.com/espressif/esp-idf/issues/2884
1. esp32-pico use standard spi driver to access psram
2. for esp32-pico, flash and psram share the clock
3. for esp32-pico, psram cs io can be overwrite via menuconfig
timer_process_alarm function of esp_timer holds a spinlock for the
entire duration of its operation, except for the time when timer
callback function is called. It is possible that when
timer_process_alarm releases the spinlock, a higher priority task may
run and delete the timer. Then the execution will return to
timer_process_alarm, and this will either cause a crash, or undesired
execution of callback after the timer has been stopped or deleted.
To solve this problem, add a mutex which will prevent deletion of timers
while callbacks are being dispatched.
esp32: unforce wifi if receiving beacon with no data buffered in dream state and reduce force receiving broadcast data time
See merge request idf/esp-idf!3963
state and reduce force receiving broadcast data time
1. If receiving beacon which indicates that there is no data buffered,
do not force to receive WiFi data.
2. If receiving beacon which indicates that there is broadcast data
buffered, reduce the time to force receiving broadcast data.
1. when no parent is found, send probe request via broadcast.
2. fix memory leak caused by the remove announcement being sent is not released when esp_mesh_stop() is called.
3. fix modify IE encrypt after mesh is started.
4. ignore esp_mesh_connect() if mesh automatic reconnection is enabled.
5. fix reason is cleared before vote is done.
Fixes: https://github.com/espressif/esp-idf/issues/2811
The warning print "NULL value" is only kept for event
BTC_GATTS_ACT_SET_ATTR_VALUE as this can be useful in case user forgets
to set attribute value
Signed-off-by: Hrishikesh Dhayagude <hrishi@espressif.com>
1. fix STAs can not detect disconnection from AP when encrypt transmission is used.
2. fix can not find hidden APs.
3. for root, modify the active scan time to 120ms.
4. remove all rc when clear parent Wi-Fi configuration.
5. fix error in checking Wi-Fi commit ID.
