All peripheral clocks are default enabled after chip is powered on.
When CPU starts, if reset reason is CPU reset, disable those clocks
that are not enabled before reset. Otherwise, disable all those
useless clocks.
These peripheral clocks must be enabled when the peripherals are
initialized and disabled when they are deinitialized.
1. BIT(8) of CTRL is actually read-only bit indicating interrupt status
2. BIT(0) or CTRL had inverted meaning: 1 is “level”, 0 is “edge”
3. Add definitions of prescaler values
1. add sens_struct.h
2. add definition of RTCCNTL and RTCIO
3. modify touch pad examples
4. update example code.
5. add comments add option in menuconfig
6. fix issue that pad index 8 and 9 are mismatched
7. add touch_pad_read_filtered() api to get value filtered by iir filter
8. modify touch pad isr func
9. Make the items in perihperal.ld in the sequence of address
10. delete Kconfig for touch pad
11. add touchpad filter APIs to adjust the filter
12. add touch_pad into index.rst
13. add touch_pad in Doxyfile
14. add touch_pad.rst
The address field should be placed at the highest bits of address and slv_wr_status registers. Instead of breaking the address into two parts and fill in each register, move the address to the highest bits and write to the registers respectively.
Breaking change: if you fill-in the SPI address filed in a previous version in some way and it works correctly, you still have to rewrite the address, in a more intuitive way.
Makes app image booting more reliable (256-bit rather than 8-bit verification.)
Some measurements, time to boot a 655KB app.bin file and run to app_main() execution.
(All for rev 1 silicon, ie no 340ms spurious WDT delay.)
80MHz QIO mode:
before = 300ms
after = 140ms
40MHz DIO mode:
before = 712ms
after = 577ms
40MHz DIO mode, secure boot enabled
before = 1380ms
after = 934ms
(Secure boot involves two ECC signature verifications (partition table, app) that take approx 300ms each with 80MHz CPU.)
Because of errata related to BOD reset function, brownout is handled as follows:
- attach an ISR to brownout interrupt
- when ISR happens, print a message and do a software restart
- esp_restart_nonos enables RTC watchdog, so if restart fails,
there will be one more attempt to restart (using the RTC
watchdog)
RTC watchdog didn’t have any actions configured for any of the stages.
This change configures it to use SW_SYSTEM_RESET at stage 0 and a
full reset at stage 1. The timeout is now calculated based on
RTC_SLOW_CLK frequency.
1. Name change from chopper to carrier, block diagram update, minor changes to example codes
2. mcpwm_reg.h changed, brought uniformity in comments, worked on suggestions, duty to accept float. Some name changes!
3. Minor readme changes and Indetation
4. Minor change: move mcpwm_reg.h and mcpwm_struct.h to new path
5. Minor change: addition of BLDC example code and Readme
6. Name changed from epwm to mcpwm
7. Improve the reg name in mcpwm_struct.h
8. Name change chopper>carrier, deadband>deadtime
add API to get chip info
This change adds an API to get chip info, such as chip model, enabled capabilities, size of embedded flash, silicon revision.
Hello_world example is modified to print out the information about the chip. The example is also simplified by moving all code into the main task.
Ref TW12031.
See merge request !549
1. When dual core cpu run access DPORT register, must do protection.
2. If access DPORT register, must use DPORT_REG_READ/DPORT_REG_WRITE and DPORT_XXX register operation macro.
Split common SPI stuff out of master driver; add slave driver; add workaround for DMA issue.
This merge req mainly adds a slave device. In order to do this, the original master driver is refactored into common code shared by master and slave modes, and a slave driver is added.
The other things added are:
- Added a workaround for a 'feature' of the ESP32 silicon that can lock up the receive DMA channel in some situations. This can only be fixed by resetting *both* DMA channels. The workaround implemented makes sure that the reset only happens when both channels are idle
- Got rid of the automatic choice between register- and DMA-based transfers. The master (and slave) code will now always go for a DMA transfer if a DMA channel is given, and always go for register-based transfers if no DMA channel is given.
- Add in a bunch of fixes for outstanding Github issues.
See merge request !659
