The files updated according to code review discussions.
In the sleep_modes.c removed immidiate disable of ULP mode and leave just trigger deactivation.
The esp_sleep.h is updated to have the same defines for source as esp_sleep_wakeup_cause_t.
Updated documentation in sleep_modes.rst file to include cross references and address esp_sleep_wakeup_cause_t type.
The get_time_ms() is updated to explicitly use fabs(dt) instead of abs(dt) in test_sleep.c.
Some other minor changes in test_sleep.c unit test.
(TW#18952)
Closes https://github.com/espressif/esp-idf/issues/1677
Some application lock interrupt(portENTER_CRITICAL) too long time,
it will cause bluetooth cannot react interrupt in time, then t will
cause some assert, assert info following:
1. ld_acl.c 1900
2. ld_fm.c 340
3. other assert reference to this.
It is not possible to generate 1 MHz REF_TICK from 2 MHz APB clock
(this is a limitation of REF_TICK divider circuit). Since switching
REF_TICK frequency is something we would like to avoid (to maintain
UART output even with DFS), 2 MHz frequency has been marked as
unsupported.
The issue would manifest itself in cases when switching from PM
configuration like {active=160MHz, idle=80MHz} to {active=80MHz,
idle=80Mhz}. After the configuration was changed, PM logic would
think that current frequency was 80MHz and would not do any further
switching. In fact, frequency was still 160MHz.
The old code calculated MAX() of two enum values, but CPU frequency
enum values are not ordered (2MHz goes after 240MHz). This caused
incorrect configuration to be set.
Previous code contained a check for PLL frequency to be 240MHz, while
in fact 240MHz was a CPU frequency; corresponding PLL frequency is
480MHz. Fixed the comparison and replaced integer MHz values with an
enum.
This commit adds character encoding configurations in for the fatfs component.
The FF_LFN_UNICODE definition in ffconf.h can now be changed to accept UTF-8 or
UTF-16 encoded filernames. Test cases using UTF-8 encoded file paths and names in
FatFs have also been added.
Closes#1183
1. External 32kHz crystal is started for too long or it may not start at all. It is often observed at the first start.
2. At the first start, it is possible that the crystal did not start. And the recorded period was recorded as 0. Which led to a division error by zero during the transition to the deep sleep mode (Maybe somewhere else).
3. Added a unit test to test a new method of oscillation an external crystal.
4. Added a new method of oscillating of an external crystal. The legs of the crystal are fed with a 32 kHz frequency.
The new method eliminates these errors.
Added unit test: `\esp-idf\components\soc\esp32\test\test_rtc_clk.c`: `make TEST_COMPONENTS=soc`
- 8 Test starting external RTC crystal. Will pass.
`Bootstrap cycles for external 32kHz crystal` - is specified in the file Kconfig by default 100.
QA tested a new method of oscillation the crystal on 25 boards. The supply of square waves on the crystal showed a 100% result in contrast to the previous method of launching the crystal. After the tests, the old method was deleted.
Closes TW19143
The expected usage is:
esp_pthread_set_cfg(cfg);
pthread_create()
If the inherit flag is set, then all subsequent threads forked by this
thread will also inherit this configuration. This avoids having to
change/prefix this for each and every pthread_create() call.
Component/bt: fix reconnect fail in smp for v3.0
See merge request idf/esp-idf!2075
(cherry picked from commit 7f2a9f0359)
d0e55335 Component/bt: fix reconnect fail in smp
The fast path of CPU frequency switch function, used in DFS, was not
waiting for the frequency switch to complete when switching from XTAL
to PLL. This resulted in incorrect reads from peripherals on APB,
where two consecutive reads could return the same value. For example,
in esp_timer, read of FRC_COUNT_REG would return same value as the
preceding read of FRC_ALARM_REG, causing time to jump by the value of
FRC_ALARM_REG / apb_freq_mhz.
- separate mode stats from lock stats by an extra comment line
- add CPU frequency column to the mode stats
- don’t print a row for light sleep if light sleep is not enabled
s_cpu_freq_by_mode array was statically initialised with 80MHz CPU
frequency in CPU_MAX and APB_MAX modes, but sdkconfig setting for the
CPU frequency could have been different. For the case of 240MHz CPU
frequency, this would cause a frequency switch between 240MHz and
80MHz to happen, even though such switch is not supported in the fast
path switching functions used by the DFS implementation.
This fixes the issue by moving initialisation into esp_pm_impl_init,
which is called at startup before the first mode switch can happen.
Fixes https://github.com/espressif/esp-idf/issues/1729.
The files updated according to code review discussions.
In the sleep_modes.c removed immidiate disable of ULP mode and leave just trigger deactivation.
The esp_sleep.h is updated to have the same defines for source as esp_sleep_wakeup_cause_t.
Updated documentation in sleep_modes.rst file to include cross references.
Some minor changes in test_sleep.c unit test.
(TW#18952)
Closes https://github.com/espressif/esp-idf/issues/1677
On most microcontrollers I have worked with one can retrieve the
current state of output GPIO pins. On ESP32 this is not the case
if the pad is not explictly configured to route this information into
the port by configuring it as input or i/o.
Thus add a warning to the API documentation of gpio_get_level().
Merges https://github.com/espressif/esp-idf/pull/1740
Added function esp_sleep_disable_wakeup_source() to deactivate wakeup trigger for selected source.
Updated documentation for this function in sleep_modes.rst file.
Updated unit test to check this functionality for light sleep.
The test_sleep.c unit test is updated to add reliability for unit testing.
(TW#18952)
Closes https://github.com/espressif/esp-idf/issues/1677
The timer wakeup function once activated cannot be disabled later using existing api. If user wants to use different wakeup sources after first sleep but it does not work. This change disables timer wakeup trigger in configuration that will be set into appropriate RTC registers in esp_light_sleep_start() function.
Added function esp_sleep_disable_wakeup_source() to deactivate wakeup trigger for selected source.
Updated documentation for this function in sleep_modes.rst file to pass make html.
Updated unit test to check this functionality for light sleep.
The test_sleep.c unit test is updated to add reliability for auto unit testing.
(TW#18952)
Closes https://github.com/espressif/esp-idf/issues/1677
This commit fixes an incorrect register definition for BLK3_RESERVED_FLAG.
Other bugs include a missing conditional check, and updated comments
on modifying eFuse checking behavior.
This commit adds support for CPU max freqeuency rating
bits in CPU. Bootloader will now print an error if attempting
to 160MHz rated ESP32 at 240MHz.
EFUSE_CHIP_VER_RESERVE has been replaced by the
frequency rating bits. Dependancies on EFUSE_CHIP_VER_RESERVE
have been changed to use EFUSE_CHIP_VER_PKG
This commit removes the lookup table mode due to inferior performance when compared
to linear mode under attenuation 0, 1 and 2. However small portions of the lookup table
are kept for the higher voltages of atten 3 (above ADC reading 2880). That voltage range
in atten 3 has non linear characteristics making the LUT performan better than linear mode.
Add back a feature that was available in the old heap implementation
in release/v2.1 and earlier: keep track of which task allocates each
block from the heap. The task handle is conditionally added as
another word in the heap poisoning header under this configuration
option CONFIG_HEAP_TASK_TRACKING.
To allow custom monitoring and debugging code to be added, add helper
functions in multi_heap.c and multi_heap_poisoning.c to provide access
to information in the block headers.
Add esp_heap_debug_dump_totals() to monitor heap usage
esp_heap_debug_dump_totals() dumps into a user-provided data structure
a summary of the amound of heap memory in region type that is used by
each task. Optionally it will also dump into another data structure
the metadata about each allocated block for a given list of tasks or
for all tasks (limited by available space).
Address change requests on PR #1498
This set of changes fixes the files in e3b702c to just add the
CONFIG_HEAP_TASK_TRACKING option without adding the new function
heap_caps_get_per_task_info() in case that is the only portion of the
PR that will be accepted. Part of the change is to remove the new .c
and .h files containing that function and to remove the line to
compile it from components/heap/component.mk since it should not have
been included in e3b702c. One or more additional commits to add the
new function will follow.
The other changes here:
- uint32_t get_all_caps() moves to heap_private.h
- replace "void* foo" with "void *foo"
- add braces around single-line "if" blocks
- replace tab characters with spaces
Address change requests on PR #1498, part 2
This set of changes fixes the files in cdf32aa to add the new function
heap_caps_get_per_task_info() with its new name and to add the line to
compile it in components/heap/component.mk. This does not address all
the suggested changes because there are some needing further
discussion.
This commit does not include the suggested change to move the
declaration of the new function into esp_heap_caps.h because the new
function references TaskHandle_t so esp_heap_caps.h would have to
include freertos/FreeRTOS.h and freertos/task.h, but FreeRTOS.h
includes esp_heap_caps.h through two other header files which results
in compilation errors because not all of FreeRTOS.h has been read yet.
Change heap_caps_get_per_task_info() to take struct of params
In addition to moving the large number of function parameters into a
struct as the single parameter, the following changes were made:
- Clear out the totals for any prepopulated tasks so the app code
doesn't have to do it.
- Rather than partitioning the per-task totals into a predetermined
set of heap capabilities, take a list of <caps,mask> pairs to
compare the caps to the heap capabilities as masked. This lets the
caller configure the desired partitioning, or none.
- Allow the totals array pointer or the blocks array pointer to be
NULL to indicate not to collect that part of the information.
- In addition to returning the total space allocated by each task,
return the number of blocks allocated by each task.
- Don't need to return the heap capabilities as part of the details
for each block since the heap region (and therefore its
capabilities) can be determined from the block address.
- Renamed heap_task_info.h to esp_heap_task_info.h to fit the naming
convention, and renamed the structs for totals and block details to
better fit the revised function name.
- Provide full Doxygen commenting for the function and parameter
structs.
Add copyright header to new files
Merges https://github.com/espressif/esp-idf/pull/1498
tools/gen_esp_err_to_name.py generates
components/esp32/esp_err_to_name.c for lookup of the error codes from
all of the IDF project and easily identify all codes in one place
This commit updates the esp_adc_cal ocmponent to support new calibration methods
which utilize calibratoin values stored in eFuse. This commit includes LUT mode
At debug log level, tcpip_adapter would print logs for each function
call scheduled onto the tcpip task. These logs contained pointers which
idf_monitor decoded, adding even more noise and useless vertical space
in logs. This change moves these log statements to verbose level.
When realloc-ing to a smaller buffer size which ends up allocated in a different heap, the heap
structure is corrupted. This can only happen:
* If heap checking is Comprehensive (meaning buffers are never shrunk in place) and the heap the buffer was originally allocated in is full.
* Calling heap_caps_realloc() to deliberately move a buffer to a different capabilities type, and shrink it at the same time.
Probable fix for https://github.com/espressif/esp-idf/issues/1582
Probably the same issue:
https://www.esp32.com/viewtopic.php?f=2&t=4583https://www.esp32.com/viewtopic.php?f=13&t=3717
use performance matrix to tracking bin size is not convenient. bin size
do change for a lot reasons.
we'll implement a new method to track it. before that, set a large
enough threshold, so we can still keep tracking it.
The TRM describes IOMUX registers are IO_MUX_x_REG for x in GPIO0-39.
Until now ESP-IDF describes them as PERIPHS_IO_MUX_(pinname)_U
This commit adds additional IOMUX register names which match the ones used in the TRM.
1. Put some lwip udp rx/tx relating functions to IRAM
2. Put some wifi rx/tx relating functions to IRAMa
3. Reduce wifi dynamic malloc from 4 to 1 for each ebuf
4. Update iperf example accordingly
5. Update libphy.a to v383
Reported from github: https://github.com/espressif/esp-idf/issues/1236
All the touch channels are enabled by default in hardware. This would interfere other RTC function on Touch IOs.
Disable touch function in touch_pad_init().
function is called but NOT withe the same 'c' string constant that the LOG*
calls used in each module, the cache check doesn't match, so the cached
entry won't get updated. There's no point in optimizing this function
anyway because it is only called rarely.
Fix `#if (LOG_LOCAL_LEVEL >= ESP_LOG_INFO)` which is always false and
produces a warning with -Wundef.
Use same pattern to compare LOG_LOCAL_LEVEL with ESP_LOG_INFO as is used
in definition of `ESP_LOG_BUFFER_HEX_LEVEL` and
`ESP_LOG_BUFFER_CHAR_LEVEL`.
Also reformat existing definitions for better readability.
Closes https://github.com/espressif/esp-idf/issues/1526
Bluedroid use a set of timer function pairs such as btu_start_timer/btu_stop_timer, btu_sys_start_timer/btu_sys_stop_timer for use, in a lack of timer release functions. Thus the timers may be exhausted after some event sequence such as repetition of connection/reconnection with different devices. The maximum timer number used in bluedroid is given by ALARM_CBS_NUM which is 30 for now. This bugfix borrowed some update from bluedroid in Andoroid 7.0, which add timer release functions which promote the recycle of timer resources.
close github issue#1037 WiFi Promiscuous filter breaks w/
WIFI_PROMIS_FILTER_MASK_ALL and issue#1404
esp_wifi_set_promiscuous_filter set WIFI_PROMIS_FILTER_MASK_ALL error
component/bt: Added the Macro for the classic BT support.
component/bt: added the bluedroid deinit method.
component/bt: allow more classic BT global variables to use dynamic allocation scheme
1. allocate memory for AVDT, AVCT control blocks when dynamic memory is used
2. allow SBC decoder buffer to use dynamic allocation scheme
component/bt: Remove the wrong changes in bt/Kconfig & Added the GATTS_INCLUDED in the gatt_free function when gatt service close.
component/bt: Shorten the abbreviation BT_ALLOCATION_FROM_SPIRAM_FIRST and BT_BLE_DYNAMIC_ENV_MEMORY two macros.
requirement from github(https://github.com/espressif/esp-idf/issues/805): to provide the position in the buffer of the pattern detected.
requirement from AT application: in AT app, when no hardware flow control is enabled, in some situation the rx buffer might be full, and the terminator “+++” might be lost, we can use pattern detect interrupt to avoid missing the terminator. When pattern detect interrupt happens, it will not send a data event at the same time.
1. Add API to get position of detected pattern in rx buffer
2. Modify UART event example
3. Add comments for uart_flush, add alias API uart_flush_input to clear the rx buffer
4. Modify the way rx_buffered_len is calculated
Changes related to DFS have broken compilation of sysview code in 1 core
mode. This change fixes this, and moves choice of the timer used for
timestamp into Kconfig. CCOUNT timer is only available as an option if
1 core mode is used. esp_timer is added as a new option, and is the
only available option if DFS is enabled.
1. "lwip_socket" should close by "lwip_close_r" other than "lwip_close"
2. for generally compatible, fix all lwip interface to normally socket interface
3. call vTaskDelete when new socket failed in case of task crash
close #https://github.com/espressif/esp32-at/issues/58
1. remove the feature mask parameter from AVRC connection state event, as the AVCTP connection can be initiated by remote device before service discovery to remote device is performed. \
In this case, AVRCP connection state event may not be reported after connection initated by remote device is established.
2. remove ESP_AVRC_CT_MAX_EVT
3. add more documentations to AVRC APIs
When INT WDT fires, panicHandler is invoked. In OCD mode, panicHandler
sets a breakpoint on the PC from the exception frame and returns.
However in case of INT WDT, interrupt flag is still set in TIMERG1
peripheral, which causes INT WDT to trigger again. This causes an
endless stream of "Core 0 panic'ed (Interrupt wdt timeout on CPU1)"
messages. OpenOCD also gets terribly confused at this point.
Disable watchdogs when exiting panic handler in OCD mode.
Clear TIMERG1 WDT interrupt flag to prevent re-entry into panic handler.
RTC_FAST_CLK_FREQ_APPROX is defined as 8500000, so 0.5MHz part was lost
when dividing by MHZ. Since cal_val is 64-bit the parens can be removed.
With 40MHz XTAL for a nominal ESP32 chip, this fixes estimated XTAL
frequency from 38 to 40MHz.
LOG_LOCAL_LEVEL is now used in a construct like:
#if (LOG_LOCAL_LEVEL >= ESP_LOG_INFO)
Make sure that LOG_LOCAL_LEVEL is defined, and don't use a type cast in
its definition, because preprocessor can not parse that.
1. ESP32 is found to suffer from AES encryption start/resume failure with specific device. Therefore temporarily disable BR/EDR Secure Connections for a workaround
2. BR/EDR Secure Connections is a feature for BT Classic introduced in Bluetooth 4.1. This change disables the setting of Secure Connections(Host Supported), and will result in the use of legacy authentication instead of secure authentication, and E0 encryption(legacy) instead of AES-CCM encryption. BLE security procedures are not affected.
Bugfix to prevent a self deleting no affinity task's memory from being freed by the
idle task of the other core before the self deleting no affinity task is able to context
switch out. prvCheckTasksWaitingTermination now checks if the task is still on
pxCurrentTCB before freeing task memory.
When tcp write/connect is running, close socket request will abort
it and continue to delete netconn and close tcp. Do not immediately
return after aborting tcp write/connect. Otherwise, tcp close
requeset will block and tcp write/connect will crash.
1. optimiz the ble stop adv callback function.
2. added the osi_mutex_unlock in the bta_gattc_wait4_service_change_ccc_cback function when the p_timer_param == NULL || p_conn == NULL.
1. fix the bug. Modify the condition that esp_bt_controller_mem_release() shoud be only called before esp_bt_controller_init() or after esp_bt_controller_deinit()
2. modify the example to use esp_bt_controller_mem_release()
libc time function now rely on esp_timer_get_time as the source of
high-resolution time, rather than FRC1 timer. Internally, on the ESP32
esp_timer implementation uses FRC2 timer.
- Change help text and labels in Kconfig to use "high-resolution timer"
instead of FRC1. Keep existing Kconfig option name to be backwards
compatible.
- Change references to "FRC1" in the source code to "FRC".
Replace explicit masks and shifts with bit fields when working with FATFS date and time representations. Also zero-initialize remaining members of struct tm.
Fixes https://github.com/espressif/esp-idf/issues/1369.
A couple of typos referencing tx_ring_buf when rx_ring_buf, slv_tx_mux
instead of slv_rx_mux.
Also, I2C_ENTER_CRITICAL()/I2C_EXIT_CRITICAL() usage was not consistent.
Only some of the _set_ functions had them. Most of the _get_ function
had them? It is my understanding that they should be wrapped around
writes, not reads? (I think we still need the lock for reading pairs of consistent values)
Also, the ticks_to_wait timeout handling in i2c_master_cmd_begin() would
not handle integer rollover correctly.
Merges https://github.com/espressif/esp-idf/pull/1180
Previously SDSPI host driver would rely on retry count when waiting for
the card to read or write data. This caused different timeout times
depending on CPU frequency and card clock frequency. In practice, card
performance does not depend on these two factors.
This change uses timeout_ms field of sdmmc_command_t introduced
previously for SDMMC host.
Fixes https://esp32.com/viewtopic.php?f=2&t=3440&p=16037 and similar
issues related to SDSPI timeouts.
FATFS does not support f_stat call for drive root. When handling stat
for drive root, don't call f_stat and just return struct st with S_IFDIR
flag set.
Closes#984
A function to change "in IRAM" status for an existing interrupt handle, without going through free/allocate of the interrupt.
mOS HW timer implementation requires this to make HW timers safe to re-set from an IRAM ISR.
This is a wrapper API for creating a Ring Buffer, which ensures that
the ringbuffer can hold the given number of items, each item being of the
same given length.
Signed-off-by: Piyush Shah <piyush@espressif.com>
Useful to check if the next item to receive is wrapped or not.
This is valid only if the ring buffer is initialised with type
RINGBUF_TYPE_ALLOWSPLIT.
This is as per the feature request here:
https://github.com/espressif/esp-idf/issues/806
Signed-off-by: Piyush Shah <piyush@espressif.com>
The earlier available API (xRingbufferGetMaxItemSize())just gives
a static max entry value possible for given ring buffer.
There was a feature request for an API which could provide
a real time available buffer size. See below:
https://github.com/espressif/esp-idf/issues/806
Signed-off-by: Piyush Shah <piyush@espressif.com>
- Use `code` tags instead of a mix of `<pre></pre>` and
`@verbatim .. @endverbatim`
- Remove manually added function prototypes from comment blocks
- Remove of grouping (`\defgroup`) — some extra work is needed
to make groups compatible with the way we auto-generate API
reference from Doxygen XML files. It's pretty easy to add the
grouping directives back if/when we implement support for
Doxygen groups in the later stages of documentation build
process.
- Hide private APIs under `@cond .. @endcond`
- Convert some comments into Doxygen-compatible ones
- Fix various documentation issues: missing documentation for
some parameters, mismatch between parameter names in comment
block and in function prototype.
- Add doxygen comments for functions which didn't have them
(thread local storage).
- Add [out] param tags where necessary
- Redefine `xTaskCreate` and `xTaskCreateStatic` as inline
functions instead of macros.
When compiling
> const ulp_insn_t program[] = {
> I_DELAY(1)
> };
with the xtensa-esp32-elf-g++ compiler i always got the error:
> sorry, unimplemented: non-trivial designated initializers not supported
>
> };
This was due to the different order in the macro and the struct. The struct has another order of the fields (opcode, unused, cycles) vs (cycles, unused, opcode):
> struct {
> uint32_t cycles : 16; /*!< Number of cycles to sleep */
> uint32_t unused : 12; /*!< Unused */
> uint32_t opcode : 4; /*!< Opcode (OPCODE_DELAY) */
> } delay; /*!< Format of DELAY instruction */
After updating the order in the macro it is possible to compile with the g++ compiler.
Merges https://github.com/espressif/esp-idf/pull/1310
This commit backports vTaskDelete() behavior from FreeRTOS v9.0.0 which
allows for the immediate freeing of task memory if the task being deleted
is not currently running and not pinned to the other core. This commit also
fixes a bug in prvCheckTasksWaitingTermination which prevented the
Idle Task from cleaning up all tasks awaiting deletion. Each iteration of the Idle
Task should traverse the xTasksWaitingTermination list and clean up all tasks
not pinned to the other core. The previous implementation would cause
prvCheckTasksWaitingTermination to return when encountering a task
pinned to the other core whilst traversing the xTasksWaitingTermination list.
The test case for vTaskDelete() has been updated to test for the bugfix and
backported deletion behavior.
* Change snprintf for strlcat does not complain w/gcc7.2.0 and it is safer, thanks @projectgus
* Use proper quotes for character literals
Merges https://github.com/espressif/esp-idf/pull/1163
