Makes app image booting more reliable (256-bit rather than 8-bit verification.)
Some measurements, time to boot a 655KB app.bin file and run to app_main() execution.
(All for rev 1 silicon, ie no 340ms spurious WDT delay.)
80MHz QIO mode:
before = 300ms
after = 140ms
40MHz DIO mode:
before = 712ms
after = 577ms
40MHz DIO mode, secure boot enabled
before = 1380ms
after = 934ms
(Secure boot involves two ECC signature verifications (partition table, app) that take approx 300ms each with 80MHz CPU.)
* Writing >4 bytes to unaligned offsets would fail
* Writiing data from flash would fail (wrong buffer was used)
* Writing >8192 bytes from RAM would over-write data multiple times
Adds test cases for the above.
1. When dual core cpu run access DPORT register, must do protection.
2. If access DPORT register, must use DPORT_REG_READ/DPORT_REG_WRITE and DPORT_XXX register operation macro.
Confusion here is that original ROM has two functions:
* SPIReadModeCnfig() - sets mode, calls enable_qio_mode/disable_qio_mode
* SPIMasterReadModeCnfig() - As above, but doesn't set QIO mode in status register
However we never want to use the ROM method to set/clear QIO mode flag, as not all flash chips work this way. Instead we
do it in flash_qio_mode.c in bootloader.
So in both cases (ROM or "patched ROM") we now call SPIMasterReadModeCnfig(), which is now named
esp_rom_spiflash_config_readmode().
1) fixed SPI_read_status: added check for flash busy flag in matrix mode
2) fixed SPI_page_program: enable write before writing data to SPI FIFO
3) SPI flash ROM funcs replacement is controlled via menuconfig option
Flash operation complete flag was cleared by the core initiating flash
operation. If the other core was running an ISR, then IPC task could
be late to enter the loop to check s_flash_op_complete by the time next
flash operation started. If the flag is cleared on the CPU waiting on
this flag, then the race condition can not happen.
* Erase range operations allow preemption after each block or sector.
* Write operations allow preemption every 8KB of data.
* Reado operations allow preemption every 16KB of data.
The issue that cache entries are not invalidated correctly sometimes
can also be reproduced for non-encrypted flash as well.
This change updates the workaround to do Cache_Flush, enabling it for
non-encrypted flash, and adds a unit test.
Partition/SPI/OTA docs & OTA new functionality
* Update partition, SPI flash & OTA docs to reflect functionality changes
* Refactor OTA implementation to perform checks mentioned in API doc
* Add new functions to OTA API: esp_ota_get_running_partition() & esp_ota_get_next_update_partition() functions
* Add spi_flash_cache2phys() & spi_flash_phys2cache() functions to support esp_ota_get_running_partition()
See merge request !513
spi_flash_unlock was missing spi_flash_guard_start, which caused cache
to be enabled during unlock operation, causing hard-to-trace crashes
and cache data corruption.
MR !441 (7c155ab) has fixed issue with esp_intr_noniram_{disable,enable}
calls not being properly protected by spi_flash_op_{lock,unlock}.
Unit test was added, but the unit test environment tests only dual-core
config. Similar issue was present in the code path for the single-core
config, where esp_intr_noniram_{disable,enable} calls were unprotected.
This change fixes the protection issue and updates the unit test to
run properly in single core config as well.
The issue with running unit tests for single core config will be
addressed in a separate MR.
Seems doing certain kinds of short reads while flash encryption is
enabled will return stale data. This fixes it, but is probably a
little heavy-handed performance wise.
Without this, it's possible for stale information to be read from
cache via mmap, even if the MMU table entry had been invalidated
prior to writing flash (if the same MMU table entry was re-used after
writing flash.)
fixes for issues observed when using spi_flash
This MR fixes three unrelated issues:
- Race condition in spi_flash_enable_interrupts_caches_and_other_cpu
when operations on unpinned tasks are performed.
The issue is reported in https://github.com/espressif/esp-idf/pull/258
- esp_intr_noniram_disable doesn’t disable interrupts when compiled in
release mode. This issue manifested itself with an illegal instruction
exception when task WDT ISR was called at the time when flash was
disabled.
Fixes https://github.com/espressif/esp-idf/issues/263.
- Tick hooks on CPU1 were not called if CPU0 scheduler was disabled for
significant amount of time (which could happen when doing flash erase).
The issue manifested itself as “INT WDT timeout on core 1” error.
Fixes https://github.com/espressif/esp-idf/issues/219.
See merge request !441
Allow writes to encrypted partitions
There is a size alignment requirement but it is checked by
spi_flash_write_encrypted. However, this check flat-out bans encrypted
writes.
Original PR on Github: https://github.com/espressif/esp-idf/pull/249
See merge request !432
spi_flash_enable_interrupts_caches_and_other_cpu function used to enable
non-IRAM interrupts after giving up flash operation lock, which would
cause problems if another task was waiting on the lock to start a flash
operation. In fact, non-IRAM interrupts should be re-enabled before the
task scheduler is resumed. Otherwise non-pinned task can be moved to the
other CPU due to preemption, causing esp_intr_noniram_enable to be
called on the other CPU, causing an abort to be triggered.
Fixes the issue reported in
https://github.com/espressif/esp-idf/pull/258
These functions are marked as inline and are called from functions which are in IRAM.
In release (-Os) builds, the compiler may decide not to inline these functions.
Placing these functions into IRAM explicitly works around this.
The following issues mentioned during MR!341 review were fixed:
1) Core dump test application description
2) Usage of CONFIG_ESP32_ENABLE_COREDUMP_TO_FLASH and CONFIG_ESP32_ENABLE_COREDUMP_TO_UART
3) FLASH_GUARD_START macro usage is fixed in flash API
4) Core dump module logging facility
5) cache util functions doc updated
6) interactive delay before print core dump to uart
7) core dump partion support in build system
1) PS is fixed up to allow GDB backtrace to work properly
2) MR!341 discussion: in core dump module: esp_panicPutXXX was replaced by ets_printf.
3) MR!341 discussion: core dump flash magic number was changed.
4) MR!341 discussion: SPI flash access API was redesigned to allow flexible critical section management.
5) test app for core dump feature was added
6) fixed base64 file reading issues on Windows platform
7) now raw bin core file is deleted upon core loader failure by epscoredump.py
Complimentary changes:
1) Partition table definitions files with core dump partition
2) Special sub-type for core dump partition
3) Special version of spi_flash_xxx
4) espcoredump.py is script to get core dump from flash and print useful info
5) FreeRTOS API was extended to get tasks snapshots
Flash encryption support
Flash encryption support in build system, tooling
To come in future MR:
* On-device key generation on first boot (for production devices), need to finalise testing of bootloader entropy seeding.
* spi_flash_encrypted_write to support non-32-byte block writes (at least optionally.)
* I think a lot of the bootloader_support component can possibly be rolled into "spiflash" and other components, to use a common API.
See merge request !240
Add dynamic interrupt allocation mechanism
This adds:
- Dynamic allocation of interrupts. Pass it the features of the interrupt you want, it'll set you up with an int.
- Shared interrupts. Enables multiple peripheral drivers to use the same interrupt.
- Marking what interrupts are fully executable from IRAM; if an int isn't marked like that it will get disabled once flash cache gets disabled.
Also:
- Modifies driver to be in line with these changes
See merge request !254
* App access functions are all flash encryption-aware
* Documentation for flash encryption
* Partition read/write is flash aware
* New encrypted write function
SPI flash hardware sends 52h command, which is a 32KB erase.
There is a matching bug in the ROM SPIEraseArea code, unless
flashchip->block_size is modified first.
rename nvs host test folder, modify .gitlab-ci.yml
remove unit-test-app build
re-format unit test files
remove extra newlines in project.mk
some refactoring for unit test part in project.mk
add build files of unit-test-app in gitignore
add README.md for unit test app
correct headings in README.md
remove files and make minor tweaks in unit test app
update .gitlab-ci.yml to use unit test app
delete unused lines in component_wrapper.mk
delete periph_i2s.h and lcd test
add text floating point in components/esp32/test/Kconfig
correct idf test build paths in .gitlab-ci.yml
New makefile component_wrapper.mk allows some variables to be set
before component.mk is evaluated. This properly fixes problems with
sdkconfig being hard to access in all phases of the build.
Including component_common.mk is no longer necessary and will print a
deprecation warning for components which use it.
ROM SPIWrite routine can work with unaligned sources, so this check is unnecessary.
Furthermore, it breaks nvs_set_str and nvs_get_blob when data pointer is unaligned.
Also fix stray backslash in COUNTER_STOP macro
This implements esp_partition_read, esp_partition_write, esp_partition_erase_range, esp_partition_mmap.
Also removed getters which didn't add much sugar after all.
spi_flash_read and spi_flash_write currently have a limitation that source and destination must be word-aligned.
This can be fixed by adding code paths for various unaligned scenarios, but function signatures also need to be adjusted.
As a first step (since we are pre-1.0 and can still change function signatures) alignment checks are added, and pointer types are relaxed to uint8_t.
Later we will add handling of unaligned operations.
This change also introduces spi_flash_erase_range and spi_flash_get_chip_size functions.
We probably need something like spi_flash_chip_size_detect which will detect actual chip size.
This is to allow single application binary to be used on a variety of boards and modules.
