The files updated according to code review discussions.
In the sleep_modes.c removed immidiate disable of ULP mode and leave just trigger deactivation.
The esp_sleep.h is updated to have the same defines for source as esp_sleep_wakeup_cause_t.
Updated documentation in sleep_modes.rst file to include cross references and address esp_sleep_wakeup_cause_t type.
The get_time_ms() is updated to explicitly use fabs(dt) instead of abs(dt) in test_sleep.c.
Some other minor changes in test_sleep.c unit test.
(TW#18952)
Closes https://github.com/espressif/esp-idf/issues/1677
Some application lock interrupt(portENTER_CRITICAL) too long time,
it will cause bluetooth cannot react interrupt in time, then t will
cause some assert, assert info following:
1. ld_acl.c 1900
2. ld_fm.c 340
3. other assert reference to this.
It is not possible to generate 1 MHz REF_TICK from 2 MHz APB clock
(this is a limitation of REF_TICK divider circuit). Since switching
REF_TICK frequency is something we would like to avoid (to maintain
UART output even with DFS), 2 MHz frequency has been marked as
unsupported.
The issue would manifest itself in cases when switching from PM
configuration like {active=160MHz, idle=80MHz} to {active=80MHz,
idle=80Mhz}. After the configuration was changed, PM logic would
think that current frequency was 80MHz and would not do any further
switching. In fact, frequency was still 160MHz.
The old code calculated MAX() of two enum values, but CPU frequency
enum values are not ordered (2MHz goes after 240MHz). This caused
incorrect configuration to be set.
Previous code contained a check for PLL frequency to be 240MHz, while
in fact 240MHz was a CPU frequency; corresponding PLL frequency is
480MHz. Fixed the comparison and replaced integer MHz values with an
enum.
This commit adds character encoding configurations in for the fatfs component.
The FF_LFN_UNICODE definition in ffconf.h can now be changed to accept UTF-8 or
UTF-16 encoded filernames. Test cases using UTF-8 encoded file paths and names in
FatFs have also been added.
Closes#1183
1. External 32kHz crystal is started for too long or it may not start at all. It is often observed at the first start.
2. At the first start, it is possible that the crystal did not start. And the recorded period was recorded as 0. Which led to a division error by zero during the transition to the deep sleep mode (Maybe somewhere else).
3. Added a unit test to test a new method of oscillation an external crystal.
4. Added a new method of oscillating of an external crystal. The legs of the crystal are fed with a 32 kHz frequency.
The new method eliminates these errors.
Added unit test: `\esp-idf\components\soc\esp32\test\test_rtc_clk.c`: `make TEST_COMPONENTS=soc`
- 8 Test starting external RTC crystal. Will pass.
`Bootstrap cycles for external 32kHz crystal` - is specified in the file Kconfig by default 100.
QA tested a new method of oscillation the crystal on 25 boards. The supply of square waves on the crystal showed a 100% result in contrast to the previous method of launching the crystal. After the tests, the old method was deleted.
Closes TW19143
The expected usage is:
esp_pthread_set_cfg(cfg);
pthread_create()
If the inherit flag is set, then all subsequent threads forked by this
thread will also inherit this configuration. This avoids having to
change/prefix this for each and every pthread_create() call.
Component/bt: fix reconnect fail in smp for v3.0
See merge request idf/esp-idf!2075
(cherry picked from commit 7f2a9f0359)
d0e55335 Component/bt: fix reconnect fail in smp
The fast path of CPU frequency switch function, used in DFS, was not
waiting for the frequency switch to complete when switching from XTAL
to PLL. This resulted in incorrect reads from peripherals on APB,
where two consecutive reads could return the same value. For example,
in esp_timer, read of FRC_COUNT_REG would return same value as the
preceding read of FRC_ALARM_REG, causing time to jump by the value of
FRC_ALARM_REG / apb_freq_mhz.
- separate mode stats from lock stats by an extra comment line
- add CPU frequency column to the mode stats
- don’t print a row for light sleep if light sleep is not enabled
s_cpu_freq_by_mode array was statically initialised with 80MHz CPU
frequency in CPU_MAX and APB_MAX modes, but sdkconfig setting for the
CPU frequency could have been different. For the case of 240MHz CPU
frequency, this would cause a frequency switch between 240MHz and
80MHz to happen, even though such switch is not supported in the fast
path switching functions used by the DFS implementation.
This fixes the issue by moving initialisation into esp_pm_impl_init,
which is called at startup before the first mode switch can happen.
Fixes https://github.com/espressif/esp-idf/issues/1729.
The files updated according to code review discussions.
In the sleep_modes.c removed immidiate disable of ULP mode and leave just trigger deactivation.
The esp_sleep.h is updated to have the same defines for source as esp_sleep_wakeup_cause_t.
Updated documentation in sleep_modes.rst file to include cross references.
Some minor changes in test_sleep.c unit test.
(TW#18952)
Closes https://github.com/espressif/esp-idf/issues/1677
On most microcontrollers I have worked with one can retrieve the
current state of output GPIO pins. On ESP32 this is not the case
if the pad is not explictly configured to route this information into
the port by configuring it as input or i/o.
Thus add a warning to the API documentation of gpio_get_level().
Merges https://github.com/espressif/esp-idf/pull/1740
Added function esp_sleep_disable_wakeup_source() to deactivate wakeup trigger for selected source.
Updated documentation for this function in sleep_modes.rst file.
Updated unit test to check this functionality for light sleep.
The test_sleep.c unit test is updated to add reliability for unit testing.
(TW#18952)
Closes https://github.com/espressif/esp-idf/issues/1677
The timer wakeup function once activated cannot be disabled later using existing api. If user wants to use different wakeup sources after first sleep but it does not work. This change disables timer wakeup trigger in configuration that will be set into appropriate RTC registers in esp_light_sleep_start() function.
Added function esp_sleep_disable_wakeup_source() to deactivate wakeup trigger for selected source.
Updated documentation for this function in sleep_modes.rst file to pass make html.
Updated unit test to check this functionality for light sleep.
The test_sleep.c unit test is updated to add reliability for auto unit testing.
(TW#18952)
Closes https://github.com/espressif/esp-idf/issues/1677
This commit fixes an incorrect register definition for BLK3_RESERVED_FLAG.
Other bugs include a missing conditional check, and updated comments
on modifying eFuse checking behavior.
This commit adds support for CPU max freqeuency rating
bits in CPU. Bootloader will now print an error if attempting
to 160MHz rated ESP32 at 240MHz.
EFUSE_CHIP_VER_RESERVE has been replaced by the
frequency rating bits. Dependancies on EFUSE_CHIP_VER_RESERVE
have been changed to use EFUSE_CHIP_VER_PKG
This commit removes the lookup table mode due to inferior performance when compared
to linear mode under attenuation 0, 1 and 2. However small portions of the lookup table
are kept for the higher voltages of atten 3 (above ADC reading 2880). That voltage range
in atten 3 has non linear characteristics making the LUT performan better than linear mode.
Add back a feature that was available in the old heap implementation
in release/v2.1 and earlier: keep track of which task allocates each
block from the heap. The task handle is conditionally added as
another word in the heap poisoning header under this configuration
option CONFIG_HEAP_TASK_TRACKING.
To allow custom monitoring and debugging code to be added, add helper
functions in multi_heap.c and multi_heap_poisoning.c to provide access
to information in the block headers.
Add esp_heap_debug_dump_totals() to monitor heap usage
esp_heap_debug_dump_totals() dumps into a user-provided data structure
a summary of the amound of heap memory in region type that is used by
each task. Optionally it will also dump into another data structure
the metadata about each allocated block for a given list of tasks or
for all tasks (limited by available space).
Address change requests on PR #1498
This set of changes fixes the files in e3b702c to just add the
CONFIG_HEAP_TASK_TRACKING option without adding the new function
heap_caps_get_per_task_info() in case that is the only portion of the
PR that will be accepted. Part of the change is to remove the new .c
and .h files containing that function and to remove the line to
compile it from components/heap/component.mk since it should not have
been included in e3b702c. One or more additional commits to add the
new function will follow.
The other changes here:
- uint32_t get_all_caps() moves to heap_private.h
- replace "void* foo" with "void *foo"
- add braces around single-line "if" blocks
- replace tab characters with spaces
Address change requests on PR #1498, part 2
This set of changes fixes the files in cdf32aa to add the new function
heap_caps_get_per_task_info() with its new name and to add the line to
compile it in components/heap/component.mk. This does not address all
the suggested changes because there are some needing further
discussion.
This commit does not include the suggested change to move the
declaration of the new function into esp_heap_caps.h because the new
function references TaskHandle_t so esp_heap_caps.h would have to
include freertos/FreeRTOS.h and freertos/task.h, but FreeRTOS.h
includes esp_heap_caps.h through two other header files which results
in compilation errors because not all of FreeRTOS.h has been read yet.
Change heap_caps_get_per_task_info() to take struct of params
In addition to moving the large number of function parameters into a
struct as the single parameter, the following changes were made:
- Clear out the totals for any prepopulated tasks so the app code
doesn't have to do it.
- Rather than partitioning the per-task totals into a predetermined
set of heap capabilities, take a list of <caps,mask> pairs to
compare the caps to the heap capabilities as masked. This lets the
caller configure the desired partitioning, or none.
- Allow the totals array pointer or the blocks array pointer to be
NULL to indicate not to collect that part of the information.
- In addition to returning the total space allocated by each task,
return the number of blocks allocated by each task.
- Don't need to return the heap capabilities as part of the details
for each block since the heap region (and therefore its
capabilities) can be determined from the block address.
- Renamed heap_task_info.h to esp_heap_task_info.h to fit the naming
convention, and renamed the structs for totals and block details to
better fit the revised function name.
- Provide full Doxygen commenting for the function and parameter
structs.
Add copyright header to new files
Merges https://github.com/espressif/esp-idf/pull/1498
tools/gen_esp_err_to_name.py generates
components/esp32/esp_err_to_name.c for lookup of the error codes from
all of the IDF project and easily identify all codes in one place
This commit updates the esp_adc_cal ocmponent to support new calibration methods
which utilize calibratoin values stored in eFuse. This commit includes LUT mode
At debug log level, tcpip_adapter would print logs for each function
call scheduled onto the tcpip task. These logs contained pointers which
idf_monitor decoded, adding even more noise and useless vertical space
in logs. This change moves these log statements to verbose level.
When realloc-ing to a smaller buffer size which ends up allocated in a different heap, the heap
structure is corrupted. This can only happen:
* If heap checking is Comprehensive (meaning buffers are never shrunk in place) and the heap the buffer was originally allocated in is full.
* Calling heap_caps_realloc() to deliberately move a buffer to a different capabilities type, and shrink it at the same time.
Probable fix for https://github.com/espressif/esp-idf/issues/1582
Probably the same issue:
https://www.esp32.com/viewtopic.php?f=2&t=4583https://www.esp32.com/viewtopic.php?f=13&t=3717
use performance matrix to tracking bin size is not convenient. bin size
do change for a lot reasons.
we'll implement a new method to track it. before that, set a large
enough threshold, so we can still keep tracking it.
The TRM describes IOMUX registers are IO_MUX_x_REG for x in GPIO0-39.
Until now ESP-IDF describes them as PERIPHS_IO_MUX_(pinname)_U
This commit adds additional IOMUX register names which match the ones used in the TRM.
1. Put some lwip udp rx/tx relating functions to IRAM
2. Put some wifi rx/tx relating functions to IRAMa
3. Reduce wifi dynamic malloc from 4 to 1 for each ebuf
4. Update iperf example accordingly
5. Update libphy.a to v383
function is called but NOT withe the same 'c' string constant that the LOG*
calls used in each module, the cache check doesn't match, so the cached
entry won't get updated. There's no point in optimizing this function
anyway because it is only called rarely.
Fix `#if (LOG_LOCAL_LEVEL >= ESP_LOG_INFO)` which is always false and
produces a warning with -Wundef.
Use same pattern to compare LOG_LOCAL_LEVEL with ESP_LOG_INFO as is used
in definition of `ESP_LOG_BUFFER_HEX_LEVEL` and
`ESP_LOG_BUFFER_CHAR_LEVEL`.
Also reformat existing definitions for better readability.
Closes https://github.com/espressif/esp-idf/issues/1526
