The argument to ulp_run should be expressed in 32-bit words. Both the
address of ulp_entry and RTC_SLOW_MEM already are uint32_t*, so their
difference is the difference in addresses divided by sizeof(uint32_t).
Therefore the extra division by sizeof(uint32_t) is not needed.
This change adds a check for compatibility between the nvs version
found on nvs flash and the one assumed by running code during nvs
initialization. Any mismatch is reported to the user using new error
code ESP_ERR_NVS_NEW_VERSION_FOUND.
End handle is incorrectly printed as start handle
Tested that gatt_client, gatt_security_client and gattc_multi_connect compile successfully
Signed-off-by: Hrishikesh Dhayagude <hrishi@espressif.com>
Add a command `make erase_ota` - erases otadata if it there is in the
partition table otherwise error 'Partition table does not have ota_data partition'.
Closes https://github.com/espressif/esp-idf/issues/1821
- call rtc_gpio_init for pins which aren't configured as RTC by default
- for RTC IOs 16 and 17, read higher part of the input register
- automatically convert GPIO number into RTC IO number
- use ulp_set_wakeup_period instead of writing to register
An existing UART driver does not support RS485 half duplex mode.
This task adds this functionality to ESP_IDF UART driver.
driver/uart.c/h: updated to add support of RS485 half duplex mode
examples/peripherals/uart_echo_rs485/main/rs485_example.c: added test example
components/driver/test/test_uart.c: added test of RS485 half duplex mode
docs/en/api-reference/peripherals/uart.rst: updated documentation
test_uart.c: suppress GCC warnings about discarded const qualifiers
uart.rst: remove sphinx warning - "Duplicate explicit target name"
simple change in uart.h file
update (test_uart.c) after rebase from master
update uart.rst, uart.c, rs485_example.c
Update example description in file Readme.md
update uart.c/h, uart.rst, test_uart.c according to review results
update uart.h (uart_set_rx_timeout() description
test_uart.c remove ignore tag
uart.c/h: fix param errors
test_uart.c: Remove GCC warning supress
uart.rst: fix the notes
rs485_example.c: fix output
uart.c: remove reset using UART_RXFIFO_RST from driver.
readme.md: Update example description
The tests are completed using RS485 adapters hardware connected to two ESP32 WROVER KITs.
TW#13812
Closes https://github.com/espressif/esp-idf/pull/667
Closes https://github.com/espressif/esp-idf/pull/1006
An existing UART driver does not support RS485 half duplex mode.
This task adds this functionality to ESP_IDF UART driver.
driver/uart.c/h: updated to add support of RS485 half duplex mode
examples/peripherals/uart_echo_rs485/main/rs485_example.c: added test example
components/driver/test/test_uart.c: added test of RS485 half duplex mode
docs/en/api-reference/peripherals/uart.rst: updated documentation
test_uart.c: suppress GCC warnings about discarded const qualifiers
uart.rst: remove sphinx warning - "Duplicate explicit target name"
simple change in uart.h file
update (test_uart.c) after rebase from master
update uart.rst, uart.c, rs485_example.c
Update example description in file Readme.md
update uart.c/h, uart.rst, test_uart.c according to review results
update uart.h (uart_set_rx_timeout() description
test_uart.c remove ignore tag
uart.c/h: fix param errors
test_uart.c: Remove GCC warning supress
uart.rst: fix the notes
rs485_example.c: fix output
The tests are completed using RS485 adapters hardware connected to two ESP32 WROVER KITs.
TW#13812
Closes https://github.com/espressif/esp-idf/pull/667
Closes https://github.com/espressif/esp-idf/pull/1006
An existing UART driver does not support RS485 half duplex mode.
This task adds this functionality to ESP_IDF UART driver.
driver/uart.c/h: updated to add support of RS485 half duplex mode
examples/peripherals/uart_echo_rs485/main/rs485_example.c: added test example
components/driver/test/test_uart.c: added test of RS485 half duplex mode
docs/en/api-reference/peripherals/uart.rst: updated documentation
test_uart.c: suppress GCC warnings about discarded const qualifiers
uart.rst: remove sphinx warning - "Duplicate explicit target name"
simple change in uart.h file
update (test_uart.c) after rebase from master
update uart.rst, uart.c, rs485_example.c
Update example description in file Readme.md
update uart.c/h, uart.rst, test_uart.c according to review results
The tests are completed using RS485 adapters hardware connected to two ESP32 WROVER KITs.
TW#13812
Closes https://github.com/espressif/esp-idf/pull/667
Closes https://github.com/espressif/esp-idf/pull/1006
coap client parse a string by `coap_split_uri`,fetch host should by `host.length`
otherwise, would cause `gethostbyname` failed because of inappropriate parameter.
1. add APIs to set/get announce interval values.
2. add API to enable/disable the min rate to 6Mbps for data packages.
3. add APIs to set/get RSSI threshold values.
4. fix ap_loss.
Moved useful functions from wrapped assert functions, because option `CONFIG_OPTIMIZATION_ASSERTIONS_DISABLED=y` will remove this functions.
Closes https://github.com/espressif/esp-idf/issues/2068
1. add mesh_assoc_t to esp_mesh_internal.h file.
2. rename "node" to "device" in esp_mesh.h.
3. add MESH_EVENT_SCAN_DONE event.
4. add APIs esp_mesh_scan_get_ap_record() and esp_mesh_scan_get_ap_ie_len() to get scan results.
5. modify API esp_mesh_set_self_organized() by adding parameter "select_parent".
6. modify API esp_mesh_set_parent() by adding parameter "parent_mesh_id"
7. add manual networking example.
Earlier they have to be selected at the compile time through sdkconfig.
A2DP sink and source application tested with this change.
Signed-off-by: Amey Inamdar <amey@espressif.com>
Add error handling for http client
set ssid password correct with Example_WIFI test, and clear password before free
Fixed the CI failure due to HTTP errror names
In situations where idle task runs a lot of idle hooks or cleanup code
(due to pthread local storage, etc) it can use more than 1KB of stack.
(I think the trigger is if a context switch happens at the right point
in the TLS cleanup).
Also removes an sdkconfig.default which accidentally set all config items,
including this stack size.
Refactor IDF "project" functionality under a wrapping of the default
"project" command, so we can tweak it a bit...
Will need more testing in other environments.
* Philosophical: "explicit is better than implicit".
* Practical: Allows useful errors if invalid directories given in components as the defaults aren't
always used. Also trims the -I path from a number of components that have no actual include
directory.
* Simplifies knowing which components will be header-only and which won't
component/bt: optimiz the code
component/bt: optimiz the code.
component/bt: added the l2c change.
component/bt: Added the modified.
component/bt: change the indicate callback function.
component/bt: added the BLE throughput test gattc & gatts example.
component/bt: Change the sdkconfig.default CONFIG_GATTS_NOTIFY_THROUGHPUT setting.
component/bt: Change the throughput_client_task delay method.
component/bt: change the btu task size from 4096 to 5096
comonent/bt: close the print when congest.
component/bt: Added the CPU frequency set method to the readme file.
component/bt: Change the gatts_demo_char1_val to gl_profile_tab[PROFILE_A_APP_ID].char_handle to avoid make error.
example/ble_throughput: Added the Readme explanation.
component/bt: Added the bt lib change.
component/bt: Update the bt lib & Change the LOG level from ERROR to DEBUG when congest.
component/bt: Fixed the bug of timer start assign error.
component/bt: Change back the gattc & gatts demo with same as the master.
example/ble_throughput: Fixed the bug when prepare write of the ble throughput.
component/bt: Update the check_sum algorithm.
component/bt: Change Added the path when used the include file of "l2cdefs.h" & "l2c_api.h".
example/throughput_client: Added the Freertos related header files to ble throughput client demo to avoid compile error.
1. add the L1 include path with a prefix, such like osi/list.h, stack/a2d_api.h and etc.
2. modify component, only bluedroid/api/include/api is export to another component and application,
other include path just for bluedroid used
3. put bluedroid/include into common/include/common, so the root directory of bluedroid have no include path.
4. modify doxygen to use esp_bt.h and redirect to
component/bt/bluedroid/api/include/api/
fix compile
