The bug will cause memory corrupted (the largest range is from 0x3ffc0000 ~ 0x3ffc8000),
some strange error will happen, like IllegalInstruction, LoadProhibited and .etc.
Fix following WiFi bugs:
1. Fix a crash bug which is caused by WiFi static TX buffer alloc/free.
2. Fix the bug that iphone fails to connect to ESP32 AP by enabling AP BAR receiving.
3. Fix the bug that ESP32 station fails to connect some APs, such as Xiaomi hotspot etc,
after reset.
This commit adds the ability for backtracing to trace from the itnerrupt to the
task stack, and across nested interrupts. Test cases have also been added.
See merge request !4084
Note: "Test backtrace from abort" reset reason modified by removing abort as a reason.
Previously, hardware SHA engine "locks" were mutex semaphores. This meant that the task which
started a particular SHA session (in hardware) needed to finalise that session, or an invalid
FreeRTOS state was created.
Replace with binary semaphore which can be shared between tasks.
Includes a unit test, but unit test doesn't crash even without this fix
(some other unknown condition is required).
In some cases, linker could choose to use ROM functions instead of the
ones defined in IDF.
For functions used in ROM stub table, this would lead to infinite
recursion when the corresponding function was called from ROM.
For crypto functions, some of these were modified in IDF, and
incompatible with ROM counterparts.
If zero-overhead loop buffer is enabled, under certain rare conditions
when executing a zero-overhead loop, the CPU may attempt to execute an invalid instruction. Work around by disabling the buffer.
Due to a hardware limitation in ESP32, the first four bytes of some
CSI data is invalid, not the last four bytes.
Correct a mistake of CSI sub-carrier index in documentation.
1. fix bug PHY/RTC functions called in ISR (update phy to v4007)
2. add UnitTest to test it
3. fix task watchdog bug when wifi change channel
4. disable/enable agc to mac deinit/init
5. add UnitTest Job
state and reduce force receiving broadcast data time
1. If receiving beacon which indicates that there is no data
buffered, do not force to receive WiFi data.
2. If receiving beacon which indicates that there is broadcast data
buffered, reduce the time to force receiving broadcast data.
timer_process_alarm function of esp_timer holds a spinlock for the
entire duration of its operation, except for the time when timer
callback function is called. It is possible that when
timer_process_alarm releases the spinlock, a higher priority task may
run and delete the timer. Then the execution will return to
timer_process_alarm, and this will either cause a crash, or undesired
execution of callback after the timer has been stopped or deleted.
To solve this problem, add a mutex which will prevent deletion of timers
while callbacks are being dispatched.
This fix includes following changes:
1. Fix the bug that esp_restart()/esp_wifi_stop() sometimes fails in WiFi/BT coexist mode.
2. Add a timer for WiFi stop and stop WiFi forcibly once the timer expires.
1. start an esp_timer on entering sleep to acquire pm_lock before wake up from modem sleep
2. decrease the clock division of XTAL fed to bluetooth low power clock from 32us to 2us period to allow to work under 240MHz Max CPU frequency
3. decrease the minimum sleep duration threshold to allow shorter bluetooth modem sleep period, especially for BLE with short connection interval
4. reconfigure bluetooth baseband(BT-BB) settings after PHY/RF init upon waking up from modem sleep to avoid packet RX/TX performance degradation
1. Fix interrupt watchdog timeout in bluetooth "btdm_bb_isr"
2. Fix BLE assert(512) or assert(1536) in rwble.c at line 222
3. Update librtc.a to fix BLE assert(512) in rwble.c at line 222
The #1 and #2 occurs random.
The #3 bug occurs in certain scenario:
1. If Wifi start softap and BLE is working
2. If wifi start station, but do not use normal station operation, such
as just use espnow, while BLE is working
3. Any other scenario, that wifi works without use software coexist
operation, while BLE is working(such as do advertising and ...)
4. update libcoexist.a version to v1.1.2
This commit resolves a blocking in esp_aes_block function.
Introduce:
The problem was in the fact that AES is switched off at the moment when he should give out the processed data. But because of the disabled, the operation can not be completed successfully, there is an infinite hang. The reason for this behavior is that the registers for controlling the inclusion of AES, SHA, MPI have shared registers and they were not protected from sharing.
Fix some related issue with shared using of AES SHA RSA accelerators.
Closes: https://github.com/espressif/esp-idf/issues/2295#issuecomment-432898137
Fix some wifi bugs
1. Enable RX BAR
2. Fix the bug that ESP32 AP negotiates with iphone to 11g
3. Fix the bug that ESP32 STA has ap_loss because CMCC AP contains two SSID
1. When WIFI task or other high priority task blocks the Bluetooth task, ACL RX buffer will use up, ACL RX buffer ptr will point to null and will never point to a valid adress. Causing errors in Bluetooth.
2. hcimsgs.h used whether flow control is on or off
1. resolve the error in calculating sniff anchor point that result in connection supervision timeout
2. resolve the issue of user case that requires sniff attempt is larger than 0xff
Fix following WiFi bugs:
1. Fix the bug that MIC verification fails on soft-AP mode
2. Modify mesh root to have same behavior as normal WiFi STA in state change
3. Fix the bug that sniffer can't catch control packets
4. Fix crash bug in soft-AP mode
5. Fix ACM(Admission Control Management) bug
1. fix some bugs by previous coex hw blocking bugfix,
such like, rwble.c (64, 0) line 222
2. fix bug that ble scan performance is very low when software coexist
is working.
3. update libcoexist version to v1.1.0
1. remove use EID to distinguish psram voltage
2. 1V8 64Mbit psram and 3V3 64Mbit psram use the same psram driver(standard spi interface)
3. set cs hold time register as 1
1. Add reading psram EID.
2. Configure different clock mode for different EID.
3. add API to get psram size and voltage.
4. Remove unnecessary VSPI claim.
For 32MBit@1.8V and 64MBit@3.3V psram, there should be 2 extra clock cycles after CS get high level.
For 64MBit@1.8 psram, we can just use standard SPI protocol to drive the psram. We also need to increase the HOLD time for CS in this case.
EID for psram:
32MBit 1.8v: 0x20
64MBit 1.8v: 0x26
64MBit 3.3v: 0x46
1. Fix the bug that ESP32 will reject the retry AddBA request frame
if AddBA response frame is failed to sent by WiFi LMAC
2. Fix the bug that AddBA request retrys too frequently
3. Forbid BA session setup for VO queue related TID
Routine `spi_flash_cache2phys` sometimes return incorrect value,
resulting in failure in getting currently running ota partition.
This in turn aborts firmware update process.This issue was more
prominent with SPIRAM enabled cases.
Fix ensures proper cache guards during `spi_flash_cache2phys`, and
also for few other similar APIs.
In addition, `esp_ota_get_running_partition` has also been optimized
to save currently running partition for subsequent invocations.
Fixes https://github.com/espressif/esp-idf/issues/2451
Problem Description
The reporduce steps are as follows:
1.This issue can be reproduced with 4 ESP32 devices, 2 for stations (STA1, STA2) and 2 for soft-AP (AP1, AP2)
2.Configure AP1/AP2 to the same SSID (ssid_xxx)
3.The max allowed WiFi connections of AP1 is configured to 1 and STA1 connects to AP1
4.The AP1 is close to STA2 while AP2 is far away from STA2 (but the STA2 can find the AP2 via scan)
5.STA2 connects ssid_xxx with all scan method
6.The problem will happen on STA2 because it fails to connec AP1 and never connects AP2
Phenmenon
STA fail to connect after send auth or assoc with a wrong status code, but no disconnect event report and can not connect the next one in the envrionment
Root Cause
Because there are some same ssid APs in the evnrionment, when do all channel scan, it will collect all the matched AP in rc list, because rc list is not empty, so it would send disconnect event, however, we didn't do other step such as connect to other one
VNC MR 575
closes https://github.com/espressif/esp-idf/issues/2323
fix the bug following:
1. after disable bluetooth controller, wifi cannot TX/RX any packets.
2. when software coexist working, there's a little ratio cause wifi task
watchdog timeout
3. when software coexist working, there's a little ratio cause bluetooth
cannot receive anything.
feature:
1. add libbtdm_app.a git commit local and remote checking
Known issues:
1. there's still a bug occurs with a very very low ratio cause bluetooth
cannot receive anything. The reproduce interval may great than 3days
~ 1week via 7x24 hours heavy testing.
1. suppport mesh type, mesh ID, router and IE crypt func&key at any time after mesh is initalized.
2. support modify parent at any time after mesh is configured.
3. modify manual networking example.
4. update header file.
5. fix issues in root conflicts handling.
6. add max length of beacon to menuconfig.
7. fix issue when received a beacon without DSSS.
Backport following WiFi fixes to v3.1:
1. Fix AMPDU RX sequence compitability bug
2. Optimize scan capability in all channel scan
3. Fix some modem sleep bugs
4. Update API to set CSI channel filter and HT_LTF data generating
The following commit rewrites the ESP-MESH docs. This commit includes
new diagrams and a structure approach to the mesh docs. Some mesh api references
have also been modified.
Some APs transmit AMPDU and MPDU by turns. Moreover, the sequence
numbers of AMPDU and MPDU are out of order, e.g. MPDU(1253) -
AMPDU(1251, 1252) - MPDU(1254) - AMPDU(1255, 1256). In order to
receive both AMPDU and MPDU in order, MPDU must be reordered with
AMPDU.
1. new APIs: esp_mesh_get_subnet_nodes_num() and esp_mesh_get_subnet_nodes_list().
2. fix hard to find the parent during connect.
3. disable Wi-Fi channel switch function.
4. fix a typo of MESH_EVENT_NO_PARENT_FOUND.
Fix following WiFi bugs:
1. Shouldn't scan when connect
2. Check beacon length in modem sleep
3. Fix the bug that AP may deauth wrong station when inactivity timer expires
4. Fix the bug that WiFi assert the system when receiving empty MCS in association response frame
1. modify parent switch mechanism.
2. fix non-root doesn't clear the layer value in nvs.
3. fix retransmit the remove announcement packets.
4. add API esp_mesh_flush_upstream_packets().
5. automatically adjust passsive scan time based on the change of beacon interval.
Backport following bug fixes to v3.1:
1. Bug fix of may connect to wrong AP in all channel scan
2. Station state machine change and fix ap loss
3. Add compatible to ccmp encryption
4. Update libphy.a to v3960:
4.1 Decrease phy_init time from 900us to 347us in sleep wakeup
4.2 Fix RX STBC initialization
4.3 Modify set_chan function to fix interrupt watchdog issue
5. Fix several wpa2 enterprise issues
5.1 Fix heap corrupted bug
5.2 Fix memory leak bug
5.3 Make wpa2 enterprise thread-safe
Closes https://github.com/espressif/esp-idf/issues/1569
6. Bugfix of coex wifi pm
This change adds a check for compatibility between the nvs version
found on nvs flash and the one assumed by running code during nvs
initialization. Any mismatch is reported to the user using new error
code ESP_ERR_NVS_NEW_VERSION_FOUND.
Since 94250e42a0, UART output is suspended when entering sleep mode
(deep or light sleep). This makes sense for light sleep, where sleep
normally takes small amount of time, and flushing the UART would add
a lot of latency. But this breaks existing behaviour for deep sleep,
where UART output was previously sent out before entering sleep mode.
Closes https://github.com/espressif/esp-idf/issues/2145
1. Move channel to the first row of the table.
2. Remove the condition of HT20/HT40 for they are determined by
secondary channel.
3. Clean up the CSI table.
INTERRUPT and CCOUNT registers will change outside of program control.
Making the inline assembly used to read these registers volatile
indicates this fact to the compiler.
Fixes https://github.com/espressif/esp-idf/issues/2127
1. fix BLE connection missing in coex mode
2. modify other parameters to make coex priority more reasonable
3. fix modem sleep procedure trap cause Wifi disable RF when BT is
working. Such cause that BR/EDR is difficult to be connected, BLE
connection stability decrease and so on.
4. modify BR/EDR coexist duration to imrove BR/EDR connect success
ratio.
5. Due to the hardware coexist bug, BLE scan interval/window should
be less than 0x100(about 160ms). Therefore, it will cause BLE cannot
scan any advertising packet while WiFi have higher priority
behaviour(such like RX beacon, scan, TX/RX VO packets and etc.).
1. add APIs to set/get announce interval values.
2. add API to enable/disable the min rate to 6Mbps for data packages.
3. add APIs to set/get RSSI threshold values.
4. fix ap_loss.
Since commit 94250e4, EXT0 wakeup mechanism, when wakeup level was set
to 0, started waking up chip immediately after entering deep sleep.
This failure was triggered in that commit by a change of
RTC_CNTL_MIN_SLP_VAL (i.e. minimum time in sleep mode until wakeup
can happen) from 128 cycles to 2 cycles.
The reason for this behaviour is related to the way input enable (IE)
signal going into an RTC pad is obtained:
PAD_IE = (SLP_SEL) ? SLP_IE & CHIP_SLEEP : IE,
where SLP_IE, SLP_SEL, and IE are bits of an RTC_IO register related
to the given pad. CHIP_SLEEP is the signal indicating that chip has
entered sleep mode.
The code in prepare_ext{0,1}_wakeup did not enable IE, but did enable
SLP_SEL and SLP_IE. This meant that until CHIP_SLEEP went high, PAD_IE
was 0, hence the input from the pad read 0 even if external signal
was 1. CHIP_SLEEP went high on the 2nd cycle of sleep. So when
RTC_CNTL_MIN_SLP_VAL was set to 2, the input signal from the pad was
latched as 0 at the moment when CHIP_SLEEP went high, causing EXT0
wakeup with level 0 to trigger.
This commit changes the way PAD_IE is enabled: SLP_SEL and SLP_IE are
no longer used, and IE is set to 1. If EXT0 wakeup is used, RTC_IO is
not powered down, so IE signal stays 1 both before CHIP_SLEEP goes
high and after. If EXT1 wakeup is used, RTC_IO may be powered down.
However prepare_ext1_wakeup enables Hold on the pad, locking states
of all the control signals, including IE.
Closes https://github.com/espressif/esp-idf/issues/1931
Closes https://github.com/espressif/esp-idf/issues/2043
Previously the loop in esp_timer_impl_set_alarm was necessary to catch
the case when timer count wraps around (goes from 2^32 - 1 to 0).
Since ALARM_OVERFLOW_VAL was reduced from 2^32 - 1 to 0xefffffff,
this is no longer necessary.
Fixes https://github.com/espressif/esp-idf/issues/1891
Allows you to move the partition table, it gives more space for the bootloader.
Added a new utility - parttool.py. This utility can search for the offset and/or size of the partitions by name and type/subtype. Use for getting APP_OFFSET and PHY_DATA_OFFSET.
The linker(esp32.bootloader.ld) made changes that allow you to write a custom bootloader code more.
TW14125
Before entering the deep sleep, the RTC and FRC counters are synchronized. Updating the boot_time.
Added a unit test for this case.
Fixed warnings for MULTIPLE_STAGES
Closes https://github.com/espressif/esp-idf/issues/1840
