OVMS3/Reference/ZOE/EVC_Tests.csv

1	00	Device and failure type ODB codding
2	01	General Electrical Failure
3	02	General signal failure
4	03	FM (Frequency Modulated) / PWM (Pulse Width Modulated) Failures
5	04	System Internal Failures
6	05	System Programming Failures
7	06	Algorithm Based Failures
8	07	Mechanical Failures
9	08	Bus Signal / Message Failures
10	09	Component Failures
11	0A	Not compatible
12	11	circuit short to ground
13	12	circuit short to battery
14	13	circuit open
15	14	circuit short to ground or open
16	15	circuit short to battery or open
17	16	circuit voltage below threshold
18	17	circuit voltage above threshold
19	18	circuit current below threshold
20	19	circuit current above threshold
21	1A	circuit resistance below threshold
22	1B	circuit resistance above threshold
23	1C	circuit voltage out of range
24	1D	circuit current out of range
25	1E	circuit resistance out of range
26	1F	circuit intermittent
27	20	test
28	21	signal amplitude < minimum
29	22	signal amplitude > maximum
30	23	signal stuck low
31	24	signal stuck high
32	25	signal shape / waveform failure
33	26	signal rate of change below threshold
34	27	signal rate of change above threshold
35	28	signal bias level out of range / zero adjustment failure
36	29	signal signal invalid
37	2F	signal erratic
38	31	no signal
39	32	signal low time < minimum
40	33	signal low time > maximum
41	34	signal high time < minimum
42	35	signal high time > maximum
43	36	signal frequency too low
44	37	signal frequency too high
45	38	signal frequency incorrect
46	39	incorrect has too few pulses
47	3A	incorrect has too many pulses
48	41	general checksum failure
49	42	general memory failure
50	43	special memory failure
51	44	data memory failure
52	45	program memory failure
53	46	calibration / parameter memory failure
54	47	watchdog / safety µC failure
55	48	supervision software failure
56	49	internal electronic failure
57	4A	incorrect component installed
58	4B	over temperature
59	51	not programmed
60	52	not activated
61	53	deactivated
62	54	missing calibration
63	55	not configured
64	61	signal calculation failure
65	62	signal compare failure
66	63	circuit / component protection time-out
67	64	signal plausibility failure
68	65	signal has too few transitions / events
69	66	signal has too many transitions / events
70	67	signal incorrect after event
71	68	event information
72	71	actuator stuck
73	72	actuator stuck open
74	73	actuator stuck closed
75	74	actuator slipping
76	75	emergency position not reachable
77	76	wrong mounting position
78	77	commanded position not reachable
79	78	alignment or adjustment incorrect
80	79	mechanical linkage failure
81	7A	fluid leak or seal failure
82	7B	low fluid level
83	81	invalid serial data received
84	82	alive / sequence counter incorrect / not updated
85	83	value of signal protection calculation incorrect
86	84	signal below allowable range
87	85	signal above allowable range
88	86	signal invalid
89	87	missing message
90	88	bus off
91	8F	erratic
92	91	parametric
93	92	performance or incorrect operation
94	93	no operation
95	94	unexpected operation
96	95	incorrect assembly
97	96	component internal failure
98	97	Component or system operation obstructed or blocked
99	98	component or system over temperature
100	F1	Safety Case 1
101	F2	Safety Case 2
102	F3	Multiple Failure
103	F4	Temperature too Low
104	F5	Negative Loop Error
105	F6	Positive Loop Error
106	F7	Initialisation not valid
107	F8	Overspeed
108	F9	Limp Home
109	FA	Specific Supplier
110	FB	-
111	FC	--
112	FD	Drift low
113	FE	Drift high