Add NMEA0183 Parser example to illustrate how to use uart event driver together with esp event library to get GPS information.
78 lines
2.5 KiB
Markdown
78 lines
2.5 KiB
Markdown
# UART Select Example
|
|
|
|
(See the README.md file in the upper level 'examples' directory for more information about examples.)
|
|
|
|
The UART select example is for demonstrating the use of `select()` for
|
|
synchronous I/O multiplexing on the UART interface. The example waits for a
|
|
character from UART using `select()` until a blocking read without delay or a
|
|
successful non-blocking read is possible.
|
|
|
|
Please note that the same result can be achieved by using `uart_read_bytes()`
|
|
but the use of `select()` allows to use it together with other virtual
|
|
file system (VFS) drivers, e.g. LWIP sockets.
|
|
|
|
This example can be used to develop applications for non-blocking read and write from/to various sources (UART,
|
|
sockets, ...) where a ready resource can be served without being blocked by a busy resource.
|
|
|
|
For a more comprehensive example please refer to `system/select`.
|
|
|
|
## How to use example
|
|
|
|
### Hardware Required
|
|
|
|
The example can be run on any ESP32 development board connected to a PC with a single USB cable for communication
|
|
through UART.
|
|
|
|
### Configure the project
|
|
|
|
```
|
|
make menuconfig
|
|
```
|
|
or
|
|
```
|
|
idf.py menuconfig
|
|
```
|
|
|
|
* Set serial port under Serial Flasher Options.
|
|
|
|
### Build and Flash
|
|
|
|
Build the project and flash it to the board, then run monitor tool to view serial output:
|
|
|
|
```
|
|
make -j4 flash monitor
|
|
```
|
|
or
|
|
```
|
|
idf.py flash monitor
|
|
```
|
|
|
|
(To exit the serial monitor, type ``Ctrl-]``.)
|
|
|
|
See the Getting Started Guide for full steps to configure and use ESP-IDF to build projects.
|
|
|
|
## Example Output
|
|
|
|
You can see a similar output after flashing and monitoring the application:
|
|
|
|
```
|
|
...
|
|
I (276) cpu_start: Pro cpu start user code
|
|
I (294) cpu_start: Starting scheduler on PRO CPU.
|
|
I (0) cpu_start: Starting scheduler on APP CPU.
|
|
I (10295) uart_select_example: Timeout has been reached and nothing has been received
|
|
I (15295) uart_select_example: Timeout has been reached and nothing has been received
|
|
I (20295) uart_select_example: Timeout has been reached and nothing has been received
|
|
```
|
|
|
|
You can push any key on your keyboard to see the result of a successful detection by `select()` and subsequent
|
|
blocking read (without delay). The following output shows the result of pushing `a` on the keyboard:
|
|
|
|
```
|
|
...
|
|
I (15295) uart_select_example: Timeout has been reached and nothing has been received
|
|
I (20295) uart_select_example: Timeout has been reached and nothing has been received
|
|
I (20945) uart_select_example: Received: a
|
|
I (25955) uart_select_example: Timeout has been reached and nothing has been received
|
|
...
|
|
```
|