OVMS3-idf/components/soc/esp32/include/soc/ledc_reg.h
Wangjialin d518a19d95 driver(ledc): fix ledc fade API and update the register header file
1. fix error when fading is too fast
2. fix error when setting duty and update immediately
3. update register header file to be in accord with TRM

closes https://github.com/espressif/esp-idf/issues/2903
2019-01-12 00:56:38 +08:00

2463 lines
133 KiB
C

// Copyright 2015-2016 Espressif Systems (Shanghai) PTE LTD
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
// http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
#ifndef _SOC_LEDC_REG_H_
#define _SOC_LEDC_REG_H_
#include "soc.h"
#define LEDC_HSCH0_CONF0_REG (DR_REG_LEDC_BASE + 0x0000)
/* LEDC_CLK_EN : R/W ;bitpos:[31] ;default: 1'h0 ; */
/*description: This bit is clock gating control signal. when software config
LED_PWM internal registers it controls the register clock.*/
#define LEDC_CLK_EN (BIT(31))
#define LEDC_CLK_EN_M (BIT(31))
#define LEDC_CLK_EN_V 0x1
#define LEDC_CLK_EN_S 31
/* LEDC_IDLE_LV_HSCH0 : R/W ;bitpos:[3] ;default: 1'b0 ; */
/*description: This bit is used to control the output value when high speed channel0 is off.*/
#define LEDC_IDLE_LV_HSCH0 (BIT(3))
#define LEDC_IDLE_LV_HSCH0_M (BIT(3))
#define LEDC_IDLE_LV_HSCH0_V 0x1
#define LEDC_IDLE_LV_HSCH0_S 3
/* LEDC_SIG_OUT_EN_HSCH0 : R/W ;bitpos:[2] ;default: 1'b0 ; */
/*description: This is the output enable control bit for high speed channel0*/
#define LEDC_SIG_OUT_EN_HSCH0 (BIT(2))
#define LEDC_SIG_OUT_EN_HSCH0_M (BIT(2))
#define LEDC_SIG_OUT_EN_HSCH0_V 0x1
#define LEDC_SIG_OUT_EN_HSCH0_S 2
/* LEDC_TIMER_SEL_HSCH0 : R/W ;bitpos:[1:0] ;default: 2'd0 ; */
/*description: There are four high speed timers the two bits are used to select
one of them for high speed channel0. 2'b00: seletc hstimer0. 2'b01: select hstimer1. 2'b10: select hstimer2. 2'b11: select hstimer3.*/
#define LEDC_TIMER_SEL_HSCH0 0x00000003
#define LEDC_TIMER_SEL_HSCH0_M ((LEDC_TIMER_SEL_HSCH0_V)<<(LEDC_TIMER_SEL_HSCH0_S))
#define LEDC_TIMER_SEL_HSCH0_V 0x3
#define LEDC_TIMER_SEL_HSCH0_S 0
#define LEDC_HSCH0_HPOINT_REG (DR_REG_LEDC_BASE + 0x0004)
/* LEDC_HPOINT_HSCH0 : R/W ;bitpos:[19:0] ;default: 20'h0 ; */
/*description: The output value changes to high when htimerx(x=[0 3]) selected
by high speed channel0 has reached reg_hpoint_hsch0[19:0]*/
#define LEDC_HPOINT_HSCH0 0x000FFFFF
#define LEDC_HPOINT_HSCH0_M ((LEDC_HPOINT_HSCH0_V)<<(LEDC_HPOINT_HSCH0_S))
#define LEDC_HPOINT_HSCH0_V 0xFFFFF
#define LEDC_HPOINT_HSCH0_S 0
#define LEDC_HSCH0_DUTY_REG (DR_REG_LEDC_BASE + 0x0008)
/* LEDC_DUTY_HSCH0 : R/W ;bitpos:[24:0] ;default: 25'h0 ; */
/*description: The register is used to control output duty. When hstimerx(x=[0
3]) choosed by high speed channel0 has reached reg_lpoint_hsch0 the output signal changes to low. reg_lpoint_hsch0=(reg_hpoint_hsch0[19:0]+reg_duty_hsch0[24:4]) (1) reg_lpoint_hsch0=(reg_hpoint_hsch0[19:0]+reg_duty_hsch0[24:4] +1) (2) The least four bits in this register represent the decimal part and determines when to choose (1) or (2)*/
#define LEDC_DUTY_HSCH0 0x01FFFFFF
#define LEDC_DUTY_HSCH0_M ((LEDC_DUTY_HSCH0_V)<<(LEDC_DUTY_HSCH0_S))
#define LEDC_DUTY_HSCH0_V 0x1FFFFFF
#define LEDC_DUTY_HSCH0_S 0
#define LEDC_HSCH0_CONF1_REG (DR_REG_LEDC_BASE + 0x000C)
/* LEDC_DUTY_START_HSCH0 : R/W ;bitpos:[31] ;default: 1'b0 ; */
/*description: When reg_duty_num_hsch0 reg_duty_cycle_hsch0 and reg_duty_scale_hsch0
has been configured. these register won't take effect until set reg_duty_start_hsch0. this bit is automatically cleared by hardware.*/
#define LEDC_DUTY_START_HSCH0 (BIT(31))
#define LEDC_DUTY_START_HSCH0_M (BIT(31))
#define LEDC_DUTY_START_HSCH0_V 0x1
#define LEDC_DUTY_START_HSCH0_S 31
/* LEDC_DUTY_INC_HSCH0 : R/W ;bitpos:[30] ;default: 1'b1 ; */
/*description: This register is used to increase the duty of output signal or
decrease the duty of output signal for high speed channel0.*/
#define LEDC_DUTY_INC_HSCH0 (BIT(30))
#define LEDC_DUTY_INC_HSCH0_M (BIT(30))
#define LEDC_DUTY_INC_HSCH0_V 0x1
#define LEDC_DUTY_INC_HSCH0_S 30
/* LEDC_DUTY_NUM_HSCH0 : R/W ;bitpos:[29:20] ;default: 10'h0 ; */
/*description: This register is used to control the num of increased or decreased
times for high speed channel0.*/
#define LEDC_DUTY_NUM_HSCH0 0x000003FF
#define LEDC_DUTY_NUM_HSCH0_M ((LEDC_DUTY_NUM_HSCH0_V)<<(LEDC_DUTY_NUM_HSCH0_S))
#define LEDC_DUTY_NUM_HSCH0_V 0x3FF
#define LEDC_DUTY_NUM_HSCH0_S 20
/* LEDC_DUTY_CYCLE_HSCH0 : R/W ;bitpos:[19:10] ;default: 10'h0 ; */
/*description: This register is used to increase or decrease the duty every
reg_duty_cycle_hsch0 cycles for high speed channel0.*/
#define LEDC_DUTY_CYCLE_HSCH0 0x000003FF
#define LEDC_DUTY_CYCLE_HSCH0_M ((LEDC_DUTY_CYCLE_HSCH0_V)<<(LEDC_DUTY_CYCLE_HSCH0_S))
#define LEDC_DUTY_CYCLE_HSCH0_V 0x3FF
#define LEDC_DUTY_CYCLE_HSCH0_S 10
/* LEDC_DUTY_SCALE_HSCH0 : R/W ;bitpos:[9:0] ;default: 10'h0 ; */
/*description: This register controls the increase or decrease step scale for
high speed channel0.*/
#define LEDC_DUTY_SCALE_HSCH0 0x000003FF
#define LEDC_DUTY_SCALE_HSCH0_M ((LEDC_DUTY_SCALE_HSCH0_V)<<(LEDC_DUTY_SCALE_HSCH0_S))
#define LEDC_DUTY_SCALE_HSCH0_V 0x3FF
#define LEDC_DUTY_SCALE_HSCH0_S 0
#define LEDC_HSCH0_DUTY_R_REG (DR_REG_LEDC_BASE + 0x0010)
/* LEDC_DUTY_HSCH0 : RO ;bitpos:[24:0] ;default: 25'h0 ; */
/*description: This register represents the current duty of the output signal
for high speed channel0.*/
#define LEDC_DUTY_HSCH0 0x01FFFFFF
#define LEDC_DUTY_HSCH0_M ((LEDC_DUTY_HSCH0_V)<<(LEDC_DUTY_HSCH0_S))
#define LEDC_DUTY_HSCH0_V 0x1FFFFFF
#define LEDC_DUTY_HSCH0_S 0
#define LEDC_HSCH1_CONF0_REG (DR_REG_LEDC_BASE + 0x0014)
/* LEDC_IDLE_LV_HSCH1 : R/W ;bitpos:[3] ;default: 1'b0 ; */
/*description: This bit is used to control the output value when high speed channel1 is off.*/
#define LEDC_IDLE_LV_HSCH1 (BIT(3))
#define LEDC_IDLE_LV_HSCH1_M (BIT(3))
#define LEDC_IDLE_LV_HSCH1_V 0x1
#define LEDC_IDLE_LV_HSCH1_S 3
/* LEDC_SIG_OUT_EN_HSCH1 : R/W ;bitpos:[2] ;default: 1'b0 ; */
/*description: This is the output enable control bit for high speed channel1*/
#define LEDC_SIG_OUT_EN_HSCH1 (BIT(2))
#define LEDC_SIG_OUT_EN_HSCH1_M (BIT(2))
#define LEDC_SIG_OUT_EN_HSCH1_V 0x1
#define LEDC_SIG_OUT_EN_HSCH1_S 2
/* LEDC_TIMER_SEL_HSCH1 : R/W ;bitpos:[1:0] ;default: 2'd0 ; */
/*description: There are four high speed timers the two bits are used to select
one of them for high speed channel1. 2'b00: seletc hstimer0. 2'b01: select hstimer1. 2'b10: select hstimer2. 2'b11: select hstimer3.*/
#define LEDC_TIMER_SEL_HSCH1 0x00000003
#define LEDC_TIMER_SEL_HSCH1_M ((LEDC_TIMER_SEL_HSCH1_V)<<(LEDC_TIMER_SEL_HSCH1_S))
#define LEDC_TIMER_SEL_HSCH1_V 0x3
#define LEDC_TIMER_SEL_HSCH1_S 0
#define LEDC_HSCH1_HPOINT_REG (DR_REG_LEDC_BASE + 0x0018)
/* LEDC_HPOINT_HSCH1 : R/W ;bitpos:[19:0] ;default: 20'h0 ; */
/*description: The output value changes to high when htimerx(x=[0 3]) selected
by high speed channel1 has reached reg_hpoint_hsch1[19:0]*/
#define LEDC_HPOINT_HSCH1 0x000FFFFF
#define LEDC_HPOINT_HSCH1_M ((LEDC_HPOINT_HSCH1_V)<<(LEDC_HPOINT_HSCH1_S))
#define LEDC_HPOINT_HSCH1_V 0xFFFFF
#define LEDC_HPOINT_HSCH1_S 0
#define LEDC_HSCH1_DUTY_REG (DR_REG_LEDC_BASE + 0x001C)
/* LEDC_DUTY_HSCH1 : R/W ;bitpos:[24:0] ;default: 25'h0 ; */
/*description: The register is used to control output duty. When hstimerx(x=[0
3]) choosed by high speed channel1 has reached reg_lpoint_hsch1 the output signal changes to low. reg_lpoint_hsch1=(reg_hpoint_hsch1[19:0]+reg_duty_hsch1[24:4]) (1) reg_lpoint_hsch1=(reg_hpoint_hsch1[19:0]+reg_duty_hsch1[24:4] +1) (2) The least four bits in this register represent the decimal part and determines when to choose (1) or (2)*/
#define LEDC_DUTY_HSCH1 0x01FFFFFF
#define LEDC_DUTY_HSCH1_M ((LEDC_DUTY_HSCH1_V)<<(LEDC_DUTY_HSCH1_S))
#define LEDC_DUTY_HSCH1_V 0x1FFFFFF
#define LEDC_DUTY_HSCH1_S 0
#define LEDC_HSCH1_CONF1_REG (DR_REG_LEDC_BASE + 0x0020)
/* LEDC_DUTY_START_HSCH1 : R/W ;bitpos:[31] ;default: 1'b0 ; */
/*description: When reg_duty_num_hsch1 reg_duty_cycle_hsch1 and reg_duty_scale_hsch1
has been configured. these register won't take effect until set reg_duty_start_hsch1. this bit is automatically cleared by hardware.*/
#define LEDC_DUTY_START_HSCH1 (BIT(31))
#define LEDC_DUTY_START_HSCH1_M (BIT(31))
#define LEDC_DUTY_START_HSCH1_V 0x1
#define LEDC_DUTY_START_HSCH1_S 31
/* LEDC_DUTY_INC_HSCH1 : R/W ;bitpos:[30] ;default: 1'b1 ; */
/*description: This register is used to increase the duty of output signal or
decrease the duty of output signal for high speed channel1.*/
#define LEDC_DUTY_INC_HSCH1 (BIT(30))
#define LEDC_DUTY_INC_HSCH1_M (BIT(30))
#define LEDC_DUTY_INC_HSCH1_V 0x1
#define LEDC_DUTY_INC_HSCH1_S 30
/* LEDC_DUTY_NUM_HSCH1 : R/W ;bitpos:[29:20] ;default: 10'h0 ; */
/*description: This register is used to control the num of increased or decreased
times for high speed channel1.*/
#define LEDC_DUTY_NUM_HSCH1 0x000003FF
#define LEDC_DUTY_NUM_HSCH1_M ((LEDC_DUTY_NUM_HSCH1_V)<<(LEDC_DUTY_NUM_HSCH1_S))
#define LEDC_DUTY_NUM_HSCH1_V 0x3FF
#define LEDC_DUTY_NUM_HSCH1_S 20
/* LEDC_DUTY_CYCLE_HSCH1 : R/W ;bitpos:[19:10] ;default: 10'h0 ; */
/*description: This register is used to increase or decrease the duty every
reg_duty_cycle_hsch1 cycles for high speed channel1.*/
#define LEDC_DUTY_CYCLE_HSCH1 0x000003FF
#define LEDC_DUTY_CYCLE_HSCH1_M ((LEDC_DUTY_CYCLE_HSCH1_V)<<(LEDC_DUTY_CYCLE_HSCH1_S))
#define LEDC_DUTY_CYCLE_HSCH1_V 0x3FF
#define LEDC_DUTY_CYCLE_HSCH1_S 10
/* LEDC_DUTY_SCALE_HSCH1 : R/W ;bitpos:[9:0] ;default: 10'h0 ; */
/*description: This register controls the increase or decrease step scale for
high speed channel1.*/
#define LEDC_DUTY_SCALE_HSCH1 0x000003FF
#define LEDC_DUTY_SCALE_HSCH1_M ((LEDC_DUTY_SCALE_HSCH1_V)<<(LEDC_DUTY_SCALE_HSCH1_S))
#define LEDC_DUTY_SCALE_HSCH1_V 0x3FF
#define LEDC_DUTY_SCALE_HSCH1_S 0
#define LEDC_HSCH1_DUTY_R_REG (DR_REG_LEDC_BASE + 0x0024)
/* LEDC_DUTY_HSCH1 : RO ;bitpos:[24:0] ;default: 25'h0 ; */
/*description: This register represents the current duty of the output signal
for high speed channel1.*/
#define LEDC_DUTY_HSCH1 0x01FFFFFF
#define LEDC_DUTY_HSCH1_M ((LEDC_DUTY_HSCH1_V)<<(LEDC_DUTY_HSCH1_S))
#define LEDC_DUTY_HSCH1_V 0x1FFFFFF
#define LEDC_DUTY_HSCH1_S 0
#define LEDC_HSCH2_CONF0_REG (DR_REG_LEDC_BASE + 0x0028)
/* LEDC_IDLE_LV_HSCH2 : R/W ;bitpos:[3] ;default: 1'b0 ; */
/*description: This bit is used to control the output value when high speed channel2 is off.*/
#define LEDC_IDLE_LV_HSCH2 (BIT(3))
#define LEDC_IDLE_LV_HSCH2_M (BIT(3))
#define LEDC_IDLE_LV_HSCH2_V 0x1
#define LEDC_IDLE_LV_HSCH2_S 3
/* LEDC_SIG_OUT_EN_HSCH2 : R/W ;bitpos:[2] ;default: 1'b0 ; */
/*description: This is the output enable control bit for high speed channel2*/
#define LEDC_SIG_OUT_EN_HSCH2 (BIT(2))
#define LEDC_SIG_OUT_EN_HSCH2_M (BIT(2))
#define LEDC_SIG_OUT_EN_HSCH2_V 0x1
#define LEDC_SIG_OUT_EN_HSCH2_S 2
/* LEDC_TIMER_SEL_HSCH2 : R/W ;bitpos:[1:0] ;default: 2'd0 ; */
/*description: There are four high speed timers the two bits are used to select
one of them for high speed channel2. 2'b00: seletc hstimer0. 2'b01: select hstimer1. 2'b10: select hstimer2. 2'b11: select hstimer3.*/
#define LEDC_TIMER_SEL_HSCH2 0x00000003
#define LEDC_TIMER_SEL_HSCH2_M ((LEDC_TIMER_SEL_HSCH2_V)<<(LEDC_TIMER_SEL_HSCH2_S))
#define LEDC_TIMER_SEL_HSCH2_V 0x3
#define LEDC_TIMER_SEL_HSCH2_S 0
#define LEDC_HSCH2_HPOINT_REG (DR_REG_LEDC_BASE + 0x002C)
/* LEDC_HPOINT_HSCH2 : R/W ;bitpos:[19:0] ;default: 20'h0 ; */
/*description: The output value changes to high when htimerx(x=[0 3]) selected
by high speed channel2 has reached reg_hpoint_hsch2[19:0]*/
#define LEDC_HPOINT_HSCH2 0x000FFFFF
#define LEDC_HPOINT_HSCH2_M ((LEDC_HPOINT_HSCH2_V)<<(LEDC_HPOINT_HSCH2_S))
#define LEDC_HPOINT_HSCH2_V 0xFFFFF
#define LEDC_HPOINT_HSCH2_S 0
#define LEDC_HSCH2_DUTY_REG (DR_REG_LEDC_BASE + 0x0030)
/* LEDC_DUTY_HSCH2 : R/W ;bitpos:[24:0] ;default: 25'h0 ; */
/*description: The register is used to control output duty. When hstimerx(x=[0
3]) choosed by high speed channel2 has reached reg_lpoint_hsch2 the output signal changes to low. reg_lpoint_hsch2=(reg_hpoint_hsch2[19:0]+reg_duty_hsch2[24:4]) (1) reg_lpoint_hsch2=(reg_hpoint_hsch2[19:0]+reg_duty_hsch2[24:4] +1) (2) The least four bits in this register represent the decimal part and determines when to choose (1) or (2)*/
#define LEDC_DUTY_HSCH2 0x01FFFFFF
#define LEDC_DUTY_HSCH2_M ((LEDC_DUTY_HSCH2_V)<<(LEDC_DUTY_HSCH2_S))
#define LEDC_DUTY_HSCH2_V 0x1FFFFFF
#define LEDC_DUTY_HSCH2_S 0
#define LEDC_HSCH2_CONF1_REG (DR_REG_LEDC_BASE + 0x0034)
/* LEDC_DUTY_START_HSCH2 : R/W ;bitpos:[31] ;default: 1'b0 ; */
/*description: When reg_duty_num_hsch2 reg_duty_cycle_hsch2 and reg_duty_scale_hsch2
has been configured. these register won't take effect until set reg_duty_start_hsch2. this bit is automatically cleared by hardware.*/
#define LEDC_DUTY_START_HSCH2 (BIT(31))
#define LEDC_DUTY_START_HSCH2_M (BIT(31))
#define LEDC_DUTY_START_HSCH2_V 0x1
#define LEDC_DUTY_START_HSCH2_S 31
/* LEDC_DUTY_INC_HSCH2 : R/W ;bitpos:[30] ;default: 1'b1 ; */
/*description: This register is used to increase the duty of output signal or
decrease the duty of output signal for high speed channel2.*/
#define LEDC_DUTY_INC_HSCH2 (BIT(30))
#define LEDC_DUTY_INC_HSCH2_M (BIT(30))
#define LEDC_DUTY_INC_HSCH2_V 0x1
#define LEDC_DUTY_INC_HSCH2_S 30
/* LEDC_DUTY_NUM_HSCH2 : R/W ;bitpos:[29:20] ;default: 10'h0 ; */
/*description: This register is used to control the num of increased or decreased
times for high speed channel2.*/
#define LEDC_DUTY_NUM_HSCH2 0x000003FF
#define LEDC_DUTY_NUM_HSCH2_M ((LEDC_DUTY_NUM_HSCH2_V)<<(LEDC_DUTY_NUM_HSCH2_S))
#define LEDC_DUTY_NUM_HSCH2_V 0x3FF
#define LEDC_DUTY_NUM_HSCH2_S 20
/* LEDC_DUTY_CYCLE_HSCH2 : R/W ;bitpos:[19:10] ;default: 10'h0 ; */
/*description: This register is used to increase or decrease the duty every
reg_duty_cycle_hsch2 cycles for high speed channel2.*/
#define LEDC_DUTY_CYCLE_HSCH2 0x000003FF
#define LEDC_DUTY_CYCLE_HSCH2_M ((LEDC_DUTY_CYCLE_HSCH2_V)<<(LEDC_DUTY_CYCLE_HSCH2_S))
#define LEDC_DUTY_CYCLE_HSCH2_V 0x3FF
#define LEDC_DUTY_CYCLE_HSCH2_S 10
/* LEDC_DUTY_SCALE_HSCH2 : R/W ;bitpos:[9:0] ;default: 10'h0 ; */
/*description: This register controls the increase or decrease step scale for
high speed channel2.*/
#define LEDC_DUTY_SCALE_HSCH2 0x000003FF
#define LEDC_DUTY_SCALE_HSCH2_M ((LEDC_DUTY_SCALE_HSCH2_V)<<(LEDC_DUTY_SCALE_HSCH2_S))
#define LEDC_DUTY_SCALE_HSCH2_V 0x3FF
#define LEDC_DUTY_SCALE_HSCH2_S 0
#define LEDC_HSCH2_DUTY_R_REG (DR_REG_LEDC_BASE + 0x0038)
/* LEDC_DUTY_HSCH2 : RO ;bitpos:[24:0] ;default: 25'h0 ; */
/*description: This register represents the current duty of the output signal
for high speed channel2.*/
#define LEDC_DUTY_HSCH2 0x01FFFFFF
#define LEDC_DUTY_HSCH2_M ((LEDC_DUTY_HSCH2_V)<<(LEDC_DUTY_HSCH2_S))
#define LEDC_DUTY_HSCH2_V 0x1FFFFFF
#define LEDC_DUTY_HSCH2_S 0
#define LEDC_HSCH3_CONF0_REG (DR_REG_LEDC_BASE + 0x003C)
/* LEDC_IDLE_LV_HSCH3 : R/W ;bitpos:[3] ;default: 1'b0 ; */
/*description: This bit is used to control the output value when high speed channel3 is off.*/
#define LEDC_IDLE_LV_HSCH3 (BIT(3))
#define LEDC_IDLE_LV_HSCH3_M (BIT(3))
#define LEDC_IDLE_LV_HSCH3_V 0x1
#define LEDC_IDLE_LV_HSCH3_S 3
/* LEDC_SIG_OUT_EN_HSCH3 : R/W ;bitpos:[2] ;default: 1'b0 ; */
/*description: This is the output enable control bit for high speed channel3*/
#define LEDC_SIG_OUT_EN_HSCH3 (BIT(2))
#define LEDC_SIG_OUT_EN_HSCH3_M (BIT(2))
#define LEDC_SIG_OUT_EN_HSCH3_V 0x1
#define LEDC_SIG_OUT_EN_HSCH3_S 2
/* LEDC_TIMER_SEL_HSCH3 : R/W ;bitpos:[1:0] ;default: 2'd0 ; */
/*description: There are four high speed timers the two bits are used to select
one of them for high speed channel3. 2'b00: seletc hstimer0. 2'b01: select hstimer1. 2'b10: select hstimer2. 2'b11: select hstimer3.*/
#define LEDC_TIMER_SEL_HSCH3 0x00000003
#define LEDC_TIMER_SEL_HSCH3_M ((LEDC_TIMER_SEL_HSCH3_V)<<(LEDC_TIMER_SEL_HSCH3_S))
#define LEDC_TIMER_SEL_HSCH3_V 0x3
#define LEDC_TIMER_SEL_HSCH3_S 0
#define LEDC_HSCH3_HPOINT_REG (DR_REG_LEDC_BASE + 0x0040)
/* LEDC_HPOINT_HSCH3 : R/W ;bitpos:[19:0] ;default: 20'h0 ; */
/*description: The output value changes to high when htimerx(x=[0 3]) selected
by high speed channel3 has reached reg_hpoint_hsch3[19:0]*/
#define LEDC_HPOINT_HSCH3 0x000FFFFF
#define LEDC_HPOINT_HSCH3_M ((LEDC_HPOINT_HSCH3_V)<<(LEDC_HPOINT_HSCH3_S))
#define LEDC_HPOINT_HSCH3_V 0xFFFFF
#define LEDC_HPOINT_HSCH3_S 0
#define LEDC_HSCH3_DUTY_REG (DR_REG_LEDC_BASE + 0x0044)
/* LEDC_DUTY_HSCH3 : R/W ;bitpos:[24:0] ;default: 25'h0 ; */
/*description: The register is used to control output duty. When hstimerx(x=[0
3]) choosed by high speed channel3 has reached reg_lpoint_hsch3 the output signal changes to low. reg_lpoint_hsch3=(reg_hpoint_hsch3[19:0]+reg_duty_hsch3[24:4]) (1) reg_lpoint_hsch3=(reg_hpoint_hsch3[19:0]+reg_duty_hsch3[24:4] +1) (2) The least four bits in this register represent the decimal part and determines when to choose (1) or (2)*/
#define LEDC_DUTY_HSCH3 0x01FFFFFF
#define LEDC_DUTY_HSCH3_M ((LEDC_DUTY_HSCH3_V)<<(LEDC_DUTY_HSCH3_S))
#define LEDC_DUTY_HSCH3_V 0x1FFFFFF
#define LEDC_DUTY_HSCH3_S 0
#define LEDC_HSCH3_CONF1_REG (DR_REG_LEDC_BASE + 0x0048)
/* LEDC_DUTY_START_HSCH3 : R/W ;bitpos:[31] ;default: 1'b0 ; */
/*description: When reg_duty_num_hsch3 reg_duty_cycle_hsch3 and reg_duty_scale_hsch3
has been configured. these register won't take effect until set reg_duty_start_hsch3. this bit is automatically cleared by hardware.*/
#define LEDC_DUTY_START_HSCH3 (BIT(31))
#define LEDC_DUTY_START_HSCH3_M (BIT(31))
#define LEDC_DUTY_START_HSCH3_V 0x1
#define LEDC_DUTY_START_HSCH3_S 31
/* LEDC_DUTY_INC_HSCH3 : R/W ;bitpos:[30] ;default: 1'b1 ; */
/*description: This register is used to increase the duty of output signal or
decrease the duty of output signal for high speed channel3.*/
#define LEDC_DUTY_INC_HSCH3 (BIT(30))
#define LEDC_DUTY_INC_HSCH3_M (BIT(30))
#define LEDC_DUTY_INC_HSCH3_V 0x1
#define LEDC_DUTY_INC_HSCH3_S 30
/* LEDC_DUTY_NUM_HSCH3 : R/W ;bitpos:[29:20] ;default: 10'h0 ; */
/*description: This register is used to control the num of increased or decreased
times for high speed channel3.*/
#define LEDC_DUTY_NUM_HSCH3 0x000003FF
#define LEDC_DUTY_NUM_HSCH3_M ((LEDC_DUTY_NUM_HSCH3_V)<<(LEDC_DUTY_NUM_HSCH3_S))
#define LEDC_DUTY_NUM_HSCH3_V 0x3FF
#define LEDC_DUTY_NUM_HSCH3_S 20
/* LEDC_DUTY_CYCLE_HSCH3 : R/W ;bitpos:[19:10] ;default: 10'h0 ; */
/*description: This register is used to increase or decrease the duty every
reg_duty_cycle_hsch3 cycles for high speed channel3.*/
#define LEDC_DUTY_CYCLE_HSCH3 0x000003FF
#define LEDC_DUTY_CYCLE_HSCH3_M ((LEDC_DUTY_CYCLE_HSCH3_V)<<(LEDC_DUTY_CYCLE_HSCH3_S))
#define LEDC_DUTY_CYCLE_HSCH3_V 0x3FF
#define LEDC_DUTY_CYCLE_HSCH3_S 10
/* LEDC_DUTY_SCALE_HSCH3 : R/W ;bitpos:[9:0] ;default: 10'h0 ; */
/*description: This register controls the increase or decrease step scale for
high speed channel3.*/
#define LEDC_DUTY_SCALE_HSCH3 0x000003FF
#define LEDC_DUTY_SCALE_HSCH3_M ((LEDC_DUTY_SCALE_HSCH3_V)<<(LEDC_DUTY_SCALE_HSCH3_S))
#define LEDC_DUTY_SCALE_HSCH3_V 0x3FF
#define LEDC_DUTY_SCALE_HSCH3_S 0
#define LEDC_HSCH3_DUTY_R_REG (DR_REG_LEDC_BASE + 0x004C)
/* LEDC_DUTY_HSCH3 : RO ;bitpos:[24:0] ;default: 25'h0 ; */
/*description: This register represents the current duty of the output signal
for high speed channel3.*/
#define LEDC_DUTY_HSCH3 0x01FFFFFF
#define LEDC_DUTY_HSCH3_M ((LEDC_DUTY_HSCH3_V)<<(LEDC_DUTY_HSCH3_S))
#define LEDC_DUTY_HSCH3_V 0x1FFFFFF
#define LEDC_DUTY_HSCH3_S 0
#define LEDC_HSCH4_CONF0_REG (DR_REG_LEDC_BASE + 0x0050)
/* LEDC_IDLE_LV_HSCH4 : R/W ;bitpos:[3] ;default: 1'b0 ; */
/*description: This bit is used to control the output value when high speed channel4 is off.*/
#define LEDC_IDLE_LV_HSCH4 (BIT(3))
#define LEDC_IDLE_LV_HSCH4_M (BIT(3))
#define LEDC_IDLE_LV_HSCH4_V 0x1
#define LEDC_IDLE_LV_HSCH4_S 3
/* LEDC_SIG_OUT_EN_HSCH4 : R/W ;bitpos:[2] ;default: 1'b0 ; */
/*description: This is the output enable control bit for high speed channel4*/
#define LEDC_SIG_OUT_EN_HSCH4 (BIT(2))
#define LEDC_SIG_OUT_EN_HSCH4_M (BIT(2))
#define LEDC_SIG_OUT_EN_HSCH4_V 0x1
#define LEDC_SIG_OUT_EN_HSCH4_S 2
/* LEDC_TIMER_SEL_HSCH4 : R/W ;bitpos:[1:0] ;default: 2'd0 ; */
/*description: There are four high speed timers the two bits are used to select
one of them for high speed channel4. 2'b00: seletc hstimer0. 2'b01: select hstimer1. 2'b10: select hstimer2. 2'b11: select hstimer3.*/
#define LEDC_TIMER_SEL_HSCH4 0x00000003
#define LEDC_TIMER_SEL_HSCH4_M ((LEDC_TIMER_SEL_HSCH4_V)<<(LEDC_TIMER_SEL_HSCH4_S))
#define LEDC_TIMER_SEL_HSCH4_V 0x3
#define LEDC_TIMER_SEL_HSCH4_S 0
#define LEDC_HSCH4_HPOINT_REG (DR_REG_LEDC_BASE + 0x0054)
/* LEDC_HPOINT_HSCH4 : R/W ;bitpos:[19:0] ;default: 20'h0 ; */
/*description: The output value changes to high when htimerx(x=[0 3]) selected
by high speed channel4 has reached reg_hpoint_hsch4[19:0]*/
#define LEDC_HPOINT_HSCH4 0x000FFFFF
#define LEDC_HPOINT_HSCH4_M ((LEDC_HPOINT_HSCH4_V)<<(LEDC_HPOINT_HSCH4_S))
#define LEDC_HPOINT_HSCH4_V 0xFFFFF
#define LEDC_HPOINT_HSCH4_S 0
#define LEDC_HSCH4_DUTY_REG (DR_REG_LEDC_BASE + 0x0058)
/* LEDC_DUTY_HSCH4 : R/W ;bitpos:[24:0] ;default: 25'h0 ; */
/*description: The register is used to control output duty. When hstimerx(x=[0
3]) choosed by high speed channel4 has reached reg_lpoint_hsch4 the output signal changes to low. reg_lpoint_hsch4=(reg_hpoint_hsch4[19:0]+reg_duty_hsch4[24:4]) (1) reg_lpoint_hsch4=(reg_hpoint_hsch4[19:0]+reg_duty_hsch4[24:4] +1) (2) The least four bits in this register represent the decimal part and determines when to choose (1) or (2)*/
#define LEDC_DUTY_HSCH4 0x01FFFFFF
#define LEDC_DUTY_HSCH4_M ((LEDC_DUTY_HSCH4_V)<<(LEDC_DUTY_HSCH4_S))
#define LEDC_DUTY_HSCH4_V 0x1FFFFFF
#define LEDC_DUTY_HSCH4_S 0
#define LEDC_HSCH4_CONF1_REG (DR_REG_LEDC_BASE + 0x005C)
/* LEDC_DUTY_START_HSCH4 : R/W ;bitpos:[31] ;default: 1'b0 ; */
/*description: When reg_duty_num_hsch1 reg_duty_cycle_hsch1 and reg_duty_scale_hsch1
has been configured. these register won't take effect until set reg_duty_start_hsch1. this bit is automatically cleared by hardware.*/
#define LEDC_DUTY_START_HSCH4 (BIT(31))
#define LEDC_DUTY_START_HSCH4_M (BIT(31))
#define LEDC_DUTY_START_HSCH4_V 0x1
#define LEDC_DUTY_START_HSCH4_S 31
/* LEDC_DUTY_INC_HSCH4 : R/W ;bitpos:[30] ;default: 1'b1 ; */
/*description: This register is used to increase the duty of output signal or
decrease the duty of output signal for high speed channel4.*/
#define LEDC_DUTY_INC_HSCH4 (BIT(30))
#define LEDC_DUTY_INC_HSCH4_M (BIT(30))
#define LEDC_DUTY_INC_HSCH4_V 0x1
#define LEDC_DUTY_INC_HSCH4_S 30
/* LEDC_DUTY_NUM_HSCH4 : R/W ;bitpos:[29:20] ;default: 10'h0 ; */
/*description: This register is used to control the num of increased or decreased
times for high speed channel1.*/
#define LEDC_DUTY_NUM_HSCH4 0x000003FF
#define LEDC_DUTY_NUM_HSCH4_M ((LEDC_DUTY_NUM_HSCH4_V)<<(LEDC_DUTY_NUM_HSCH4_S))
#define LEDC_DUTY_NUM_HSCH4_V 0x3FF
#define LEDC_DUTY_NUM_HSCH4_S 20
/* LEDC_DUTY_CYCLE_HSCH4 : R/W ;bitpos:[19:10] ;default: 10'h0 ; */
/*description: This register is used to increase or decrease the duty every
reg_duty_cycle_hsch4 cycles for high speed channel4.*/
#define LEDC_DUTY_CYCLE_HSCH4 0x000003FF
#define LEDC_DUTY_CYCLE_HSCH4_M ((LEDC_DUTY_CYCLE_HSCH4_V)<<(LEDC_DUTY_CYCLE_HSCH4_S))
#define LEDC_DUTY_CYCLE_HSCH4_V 0x3FF
#define LEDC_DUTY_CYCLE_HSCH4_S 10
/* LEDC_DUTY_SCALE_HSCH4 : R/W ;bitpos:[9:0] ;default: 10'h0 ; */
/*description: This register controls the increase or decrease step scale for
high speed channel4.*/
#define LEDC_DUTY_SCALE_HSCH4 0x000003FF
#define LEDC_DUTY_SCALE_HSCH4_M ((LEDC_DUTY_SCALE_HSCH4_V)<<(LEDC_DUTY_SCALE_HSCH4_S))
#define LEDC_DUTY_SCALE_HSCH4_V 0x3FF
#define LEDC_DUTY_SCALE_HSCH4_S 0
#define LEDC_HSCH4_DUTY_R_REG (DR_REG_LEDC_BASE + 0x0060)
/* LEDC_DUTY_HSCH4 : RO ;bitpos:[24:0] ;default: 25'h0 ; */
/*description: This register represents the current duty of the output signal
for high speed channel4.*/
#define LEDC_DUTY_HSCH4 0x01FFFFFF
#define LEDC_DUTY_HSCH4_M ((LEDC_DUTY_HSCH4_V)<<(LEDC_DUTY_HSCH4_S))
#define LEDC_DUTY_HSCH4_V 0x1FFFFFF
#define LEDC_DUTY_HSCH4_S 0
#define LEDC_HSCH5_CONF0_REG (DR_REG_LEDC_BASE + 0x0064)
/* LEDC_IDLE_LV_HSCH5 : R/W ;bitpos:[3] ;default: 1'b0 ; */
/*description: This bit is used to control the output value when high speed channel5 is off.*/
#define LEDC_IDLE_LV_HSCH5 (BIT(3))
#define LEDC_IDLE_LV_HSCH5_M (BIT(3))
#define LEDC_IDLE_LV_HSCH5_V 0x1
#define LEDC_IDLE_LV_HSCH5_S 3
/* LEDC_SIG_OUT_EN_HSCH5 : R/W ;bitpos:[2] ;default: 1'b0 ; */
/*description: This is the output enable control bit for high speed channel5.*/
#define LEDC_SIG_OUT_EN_HSCH5 (BIT(2))
#define LEDC_SIG_OUT_EN_HSCH5_M (BIT(2))
#define LEDC_SIG_OUT_EN_HSCH5_V 0x1
#define LEDC_SIG_OUT_EN_HSCH5_S 2
/* LEDC_TIMER_SEL_HSCH5 : R/W ;bitpos:[1:0] ;default: 2'd0 ; */
/*description: There are four high speed timers the two bits are used to select
one of them for high speed channel5. 2'b00: seletc hstimer0. 2'b01: select hstimer1. 2'b10: select hstimer2. 2'b11: select hstimer3.*/
#define LEDC_TIMER_SEL_HSCH5 0x00000003
#define LEDC_TIMER_SEL_HSCH5_M ((LEDC_TIMER_SEL_HSCH5_V)<<(LEDC_TIMER_SEL_HSCH5_S))
#define LEDC_TIMER_SEL_HSCH5_V 0x3
#define LEDC_TIMER_SEL_HSCH5_S 0
#define LEDC_HSCH5_HPOINT_REG (DR_REG_LEDC_BASE + 0x0068)
/* LEDC_HPOINT_HSCH5 : R/W ;bitpos:[19:0] ;default: 20'h0 ; */
/*description: The output value changes to high when htimerx(x=[0 3]) selected
by high speed channel5 has reached reg_hpoint_hsch5[19:0]*/
#define LEDC_HPOINT_HSCH5 0x000FFFFF
#define LEDC_HPOINT_HSCH5_M ((LEDC_HPOINT_HSCH5_V)<<(LEDC_HPOINT_HSCH5_S))
#define LEDC_HPOINT_HSCH5_V 0xFFFFF
#define LEDC_HPOINT_HSCH5_S 0
#define LEDC_HSCH5_DUTY_REG (DR_REG_LEDC_BASE + 0x006C)
/* LEDC_DUTY_HSCH5 : R/W ;bitpos:[24:0] ;default: 25'h0 ; */
/*description: The register is used to control output duty. When hstimerx(x=[0
3]) choosed by high speed channel5 has reached reg_lpoint_hsch5 the output signal changes to low. reg_lpoint_hsch5=(reg_hpoint_hsch5[19:0]+reg_duty_hsch5[24:4]) (1) reg_lpoint_hsch5=(reg_hpoint_hsch5[19:0]+reg_duty_hsch5[24:4] +1) (2) The least four bits in this register represent the decimal part and determines when to choose (1) or (2)*/
#define LEDC_DUTY_HSCH5 0x01FFFFFF
#define LEDC_DUTY_HSCH5_M ((LEDC_DUTY_HSCH5_V)<<(LEDC_DUTY_HSCH5_S))
#define LEDC_DUTY_HSCH5_V 0x1FFFFFF
#define LEDC_DUTY_HSCH5_S 0
#define LEDC_HSCH5_CONF1_REG (DR_REG_LEDC_BASE + 0x0070)
/* LEDC_DUTY_START_HSCH5 : R/W ;bitpos:[31] ;default: 1'b0 ; */
/*description: When reg_duty_num_hsch5 reg_duty_cycle_hsch5 and reg_duty_scale_hsch5
has been configured. these register won't take effect until set reg_duty_start_hsch5. this bit is automatically cleared by hardware.*/
#define LEDC_DUTY_START_HSCH5 (BIT(31))
#define LEDC_DUTY_START_HSCH5_M (BIT(31))
#define LEDC_DUTY_START_HSCH5_V 0x1
#define LEDC_DUTY_START_HSCH5_S 31
/* LEDC_DUTY_INC_HSCH5 : R/W ;bitpos:[30] ;default: 1'b1 ; */
/*description: This register is used to increase the duty of output signal or
decrease the duty of output signal for high speed channel5.*/
#define LEDC_DUTY_INC_HSCH5 (BIT(30))
#define LEDC_DUTY_INC_HSCH5_M (BIT(30))
#define LEDC_DUTY_INC_HSCH5_V 0x1
#define LEDC_DUTY_INC_HSCH5_S 30
/* LEDC_DUTY_NUM_HSCH5 : R/W ;bitpos:[29:20] ;default: 10'h0 ; */
/*description: This register is used to control the num of increased or decreased
times for high speed channel5.*/
#define LEDC_DUTY_NUM_HSCH5 0x000003FF
#define LEDC_DUTY_NUM_HSCH5_M ((LEDC_DUTY_NUM_HSCH5_V)<<(LEDC_DUTY_NUM_HSCH5_S))
#define LEDC_DUTY_NUM_HSCH5_V 0x3FF
#define LEDC_DUTY_NUM_HSCH5_S 20
/* LEDC_DUTY_CYCLE_HSCH5 : R/W ;bitpos:[19:10] ;default: 10'h0 ; */
/*description: This register is used to increase or decrease the duty every
reg_duty_cycle_hsch5 cycles for high speed channel5.*/
#define LEDC_DUTY_CYCLE_HSCH5 0x000003FF
#define LEDC_DUTY_CYCLE_HSCH5_M ((LEDC_DUTY_CYCLE_HSCH5_V)<<(LEDC_DUTY_CYCLE_HSCH5_S))
#define LEDC_DUTY_CYCLE_HSCH5_V 0x3FF
#define LEDC_DUTY_CYCLE_HSCH5_S 10
/* LEDC_DUTY_SCALE_HSCH5 : R/W ;bitpos:[9:0] ;default: 10'h0 ; */
/*description: This register controls the increase or decrease step scale for
high speed channel5.*/
#define LEDC_DUTY_SCALE_HSCH5 0x000003FF
#define LEDC_DUTY_SCALE_HSCH5_M ((LEDC_DUTY_SCALE_HSCH5_V)<<(LEDC_DUTY_SCALE_HSCH5_S))
#define LEDC_DUTY_SCALE_HSCH5_V 0x3FF
#define LEDC_DUTY_SCALE_HSCH5_S 0
#define LEDC_HSCH5_DUTY_R_REG (DR_REG_LEDC_BASE + 0x0074)
/* LEDC_DUTY_HSCH5 : RO ;bitpos:[24:0] ;default: 25'h0 ; */
/*description: This register represents the current duty of the output signal
for high speed channel5.*/
#define LEDC_DUTY_HSCH5 0x01FFFFFF
#define LEDC_DUTY_HSCH5_M ((LEDC_DUTY_HSCH5_V)<<(LEDC_DUTY_HSCH5_S))
#define LEDC_DUTY_HSCH5_V 0x1FFFFFF
#define LEDC_DUTY_HSCH5_S 0
#define LEDC_HSCH6_CONF0_REG (DR_REG_LEDC_BASE + 0x0078)
/* LEDC_IDLE_LV_HSCH6 : R/W ;bitpos:[3] ;default: 1'b0 ; */
/*description: This bit is used to control the output value when high speed channel6 is off.*/
#define LEDC_IDLE_LV_HSCH6 (BIT(3))
#define LEDC_IDLE_LV_HSCH6_M (BIT(3))
#define LEDC_IDLE_LV_HSCH6_V 0x1
#define LEDC_IDLE_LV_HSCH6_S 3
/* LEDC_SIG_OUT_EN_HSCH6 : R/W ;bitpos:[2] ;default: 1'b0 ; */
/*description: This is the output enable control bit for high speed channel6*/
#define LEDC_SIG_OUT_EN_HSCH6 (BIT(2))
#define LEDC_SIG_OUT_EN_HSCH6_M (BIT(2))
#define LEDC_SIG_OUT_EN_HSCH6_V 0x1
#define LEDC_SIG_OUT_EN_HSCH6_S 2
/* LEDC_TIMER_SEL_HSCH6 : R/W ;bitpos:[1:0] ;default: 2'd0 ; */
/*description: There are four high speed timers the two bits are used to select
one of them for high speed channel6. 2'b00: seletc hstimer0. 2'b01: select hstimer1. 2'b10: select hstimer2. 2'b11: select hstimer3.*/
#define LEDC_TIMER_SEL_HSCH6 0x00000003
#define LEDC_TIMER_SEL_HSCH6_M ((LEDC_TIMER_SEL_HSCH6_V)<<(LEDC_TIMER_SEL_HSCH6_S))
#define LEDC_TIMER_SEL_HSCH6_V 0x3
#define LEDC_TIMER_SEL_HSCH6_S 0
#define LEDC_HSCH6_HPOINT_REG (DR_REG_LEDC_BASE + 0x007C)
/* LEDC_HPOINT_HSCH6 : R/W ;bitpos:[19:0] ;default: 20'h0 ; */
/*description: The output value changes to high when htimerx(x=[0 3]) selected
by high speed channel6 has reached reg_hpoint_hsch6[19:0]*/
#define LEDC_HPOINT_HSCH6 0x000FFFFF
#define LEDC_HPOINT_HSCH6_M ((LEDC_HPOINT_HSCH6_V)<<(LEDC_HPOINT_HSCH6_S))
#define LEDC_HPOINT_HSCH6_V 0xFFFFF
#define LEDC_HPOINT_HSCH6_S 0
#define LEDC_HSCH6_DUTY_REG (DR_REG_LEDC_BASE + 0x0080)
/* LEDC_DUTY_HSCH6 : R/W ;bitpos:[24:0] ;default: 25'h0 ; */
/*description: The register is used to control output duty. When hstimerx(x=[0
3]) choosed by high speed channel6 has reached reg_lpoint_hsch6 the output signal changes to low. reg_lpoint_hsch6=(reg_hpoint_hsch6[19:0]+reg_duty_hsch6[24:4]) (1) reg_lpoint_hsch6=(reg_hpoint_hsch6[19:0]+reg_duty_hsch6[24:4] +1) (2) The least four bits in this register represent the decimal part and determines when to choose (1) or (2)*/
#define LEDC_DUTY_HSCH6 0x01FFFFFF
#define LEDC_DUTY_HSCH6_M ((LEDC_DUTY_HSCH6_V)<<(LEDC_DUTY_HSCH6_S))
#define LEDC_DUTY_HSCH6_V 0x1FFFFFF
#define LEDC_DUTY_HSCH6_S 0
#define LEDC_HSCH6_CONF1_REG (DR_REG_LEDC_BASE + 0x0084)
/* LEDC_DUTY_START_HSCH6 : R/W ;bitpos:[31] ;default: 1'b0 ; */
/*description: When reg_duty_num_hsch1 reg_duty_cycle_hsch1 and reg_duty_scale_hsch1
has been configured. these register won't take effect until set reg_duty_start_hsch1. this bit is automatically cleared by hardware.*/
#define LEDC_DUTY_START_HSCH6 (BIT(31))
#define LEDC_DUTY_START_HSCH6_M (BIT(31))
#define LEDC_DUTY_START_HSCH6_V 0x1
#define LEDC_DUTY_START_HSCH6_S 31
/* LEDC_DUTY_INC_HSCH6 : R/W ;bitpos:[30] ;default: 1'b1 ; */
/*description: This register is used to increase the duty of output signal or
decrease the duty of output signal for high speed channel6.*/
#define LEDC_DUTY_INC_HSCH6 (BIT(30))
#define LEDC_DUTY_INC_HSCH6_M (BIT(30))
#define LEDC_DUTY_INC_HSCH6_V 0x1
#define LEDC_DUTY_INC_HSCH6_S 30
/* LEDC_DUTY_NUM_HSCH6 : R/W ;bitpos:[29:20] ;default: 10'h0 ; */
/*description: This register is used to control the num of increased or decreased
times for high speed channel6.*/
#define LEDC_DUTY_NUM_HSCH6 0x000003FF
#define LEDC_DUTY_NUM_HSCH6_M ((LEDC_DUTY_NUM_HSCH6_V)<<(LEDC_DUTY_NUM_HSCH6_S))
#define LEDC_DUTY_NUM_HSCH6_V 0x3FF
#define LEDC_DUTY_NUM_HSCH6_S 20
/* LEDC_DUTY_CYCLE_HSCH6 : R/W ;bitpos:[19:10] ;default: 10'h0 ; */
/*description: This register is used to increase or decrease the duty every
reg_duty_cycle_hsch6 cycles for high speed channel6.*/
#define LEDC_DUTY_CYCLE_HSCH6 0x000003FF
#define LEDC_DUTY_CYCLE_HSCH6_M ((LEDC_DUTY_CYCLE_HSCH6_V)<<(LEDC_DUTY_CYCLE_HSCH6_S))
#define LEDC_DUTY_CYCLE_HSCH6_V 0x3FF
#define LEDC_DUTY_CYCLE_HSCH6_S 10
/* LEDC_DUTY_SCALE_HSCH6 : R/W ;bitpos:[9:0] ;default: 10'h0 ; */
/*description: This register controls the increase or decrease step scale for
high speed channel6.*/
#define LEDC_DUTY_SCALE_HSCH6 0x000003FF
#define LEDC_DUTY_SCALE_HSCH6_M ((LEDC_DUTY_SCALE_HSCH6_V)<<(LEDC_DUTY_SCALE_HSCH6_S))
#define LEDC_DUTY_SCALE_HSCH6_V 0x3FF
#define LEDC_DUTY_SCALE_HSCH6_S 0
#define LEDC_HSCH6_DUTY_R_REG (DR_REG_LEDC_BASE + 0x0088)
/* LEDC_DUTY_HSCH6 : RO ;bitpos:[24:0] ;default: 25'h0 ; */
/*description: This register represents the current duty of the output signal
for high speed channel6.*/
#define LEDC_DUTY_HSCH6 0x01FFFFFF
#define LEDC_DUTY_HSCH6_M ((LEDC_DUTY_HSCH6_V)<<(LEDC_DUTY_HSCH6_S))
#define LEDC_DUTY_HSCH6_V 0x1FFFFFF
#define LEDC_DUTY_HSCH6_S 0
#define LEDC_HSCH7_CONF0_REG (DR_REG_LEDC_BASE + 0x008C)
/* LEDC_IDLE_LV_HSCH7 : R/W ;bitpos:[3] ;default: 1'b0 ; */
/*description: This bit is used to control the output value when high speed channel7 is off.*/
#define LEDC_IDLE_LV_HSCH7 (BIT(3))
#define LEDC_IDLE_LV_HSCH7_M (BIT(3))
#define LEDC_IDLE_LV_HSCH7_V 0x1
#define LEDC_IDLE_LV_HSCH7_S 3
/* LEDC_SIG_OUT_EN_HSCH7 : R/W ;bitpos:[2] ;default: 1'b0 ; */
/*description: This is the output enable control bit for high speed channel7.*/
#define LEDC_SIG_OUT_EN_HSCH7 (BIT(2))
#define LEDC_SIG_OUT_EN_HSCH7_M (BIT(2))
#define LEDC_SIG_OUT_EN_HSCH7_V 0x1
#define LEDC_SIG_OUT_EN_HSCH7_S 2
/* LEDC_TIMER_SEL_HSCH7 : R/W ;bitpos:[1:0] ;default: 2'd0 ; */
/*description: There are four high speed timers the two bits are used to select
one of them for high speed channel7. 2'b00: seletc hstimer0. 2'b01: select hstimer1. 2'b10: select hstimer2. 2'b11: select hstimer3.*/
#define LEDC_TIMER_SEL_HSCH7 0x00000003
#define LEDC_TIMER_SEL_HSCH7_M ((LEDC_TIMER_SEL_HSCH7_V)<<(LEDC_TIMER_SEL_HSCH7_S))
#define LEDC_TIMER_SEL_HSCH7_V 0x3
#define LEDC_TIMER_SEL_HSCH7_S 0
#define LEDC_HSCH7_HPOINT_REG (DR_REG_LEDC_BASE + 0x0090)
/* LEDC_HPOINT_HSCH7 : R/W ;bitpos:[19:0] ;default: 20'h0 ; */
/*description: The output value changes to high when htimerx(x=[0 3]) selected
by high speed channel7 has reached reg_hpoint_hsch7[19:0]*/
#define LEDC_HPOINT_HSCH7 0x000FFFFF
#define LEDC_HPOINT_HSCH7_M ((LEDC_HPOINT_HSCH7_V)<<(LEDC_HPOINT_HSCH7_S))
#define LEDC_HPOINT_HSCH7_V 0xFFFFF
#define LEDC_HPOINT_HSCH7_S 0
#define LEDC_HSCH7_DUTY_REG (DR_REG_LEDC_BASE + 0x0094)
/* LEDC_DUTY_HSCH7 : R/W ;bitpos:[24:0] ;default: 25'h0 ; */
/*description: The register is used to control output duty. When hstimerx(x=[0
3]) choosed by high speed channel7 has reached reg_lpoint_hsch7 the output signal changes to low. reg_lpoint_hsch7=(reg_hpoint_hsch7[19:0]+reg_duty_hsch7[24:4]) (1) reg_lpoint_hsch7=(reg_hpoint_hsch7[19:0]+reg_duty_hsch7[24:4] +1) (2) The least four bits in this register represent the decimal part and determines when to choose (1) or (2)*/
#define LEDC_DUTY_HSCH7 0x01FFFFFF
#define LEDC_DUTY_HSCH7_M ((LEDC_DUTY_HSCH7_V)<<(LEDC_DUTY_HSCH7_S))
#define LEDC_DUTY_HSCH7_V 0x1FFFFFF
#define LEDC_DUTY_HSCH7_S 0
#define LEDC_HSCH7_CONF1_REG (DR_REG_LEDC_BASE + 0x0098)
/* LEDC_DUTY_START_HSCH7 : R/W ;bitpos:[31] ;default: 1'b0 ; */
/*description: When reg_duty_num_hsch1 reg_duty_cycle_hsch1 and reg_duty_scale_hsch1
has been configured. these register won't take effect until set reg_duty_start_hsch1. this bit is automatically cleared by hardware.*/
#define LEDC_DUTY_START_HSCH7 (BIT(31))
#define LEDC_DUTY_START_HSCH7_M (BIT(31))
#define LEDC_DUTY_START_HSCH7_V 0x1
#define LEDC_DUTY_START_HSCH7_S 31
/* LEDC_DUTY_INC_HSCH7 : R/W ;bitpos:[30] ;default: 1'b1 ; */
/*description: This register is used to increase the duty of output signal or
decrease the duty of output signal for high speed channel6.*/
#define LEDC_DUTY_INC_HSCH7 (BIT(30))
#define LEDC_DUTY_INC_HSCH7_M (BIT(30))
#define LEDC_DUTY_INC_HSCH7_V 0x1
#define LEDC_DUTY_INC_HSCH7_S 30
/* LEDC_DUTY_NUM_HSCH7 : R/W ;bitpos:[29:20] ;default: 10'h0 ; */
/*description: This register is used to control the num of increased or decreased
times for high speed channel6.*/
#define LEDC_DUTY_NUM_HSCH7 0x000003FF
#define LEDC_DUTY_NUM_HSCH7_M ((LEDC_DUTY_NUM_HSCH7_V)<<(LEDC_DUTY_NUM_HSCH7_S))
#define LEDC_DUTY_NUM_HSCH7_V 0x3FF
#define LEDC_DUTY_NUM_HSCH7_S 20
/* LEDC_DUTY_CYCLE_HSCH7 : R/W ;bitpos:[19:10] ;default: 10'h0 ; */
/*description: This register is used to increase or decrease the duty every
reg_duty_cycle_hsch7 cycles for high speed channel7.*/
#define LEDC_DUTY_CYCLE_HSCH7 0x000003FF
#define LEDC_DUTY_CYCLE_HSCH7_M ((LEDC_DUTY_CYCLE_HSCH7_V)<<(LEDC_DUTY_CYCLE_HSCH7_S))
#define LEDC_DUTY_CYCLE_HSCH7_V 0x3FF
#define LEDC_DUTY_CYCLE_HSCH7_S 10
/* LEDC_DUTY_SCALE_HSCH7 : R/W ;bitpos:[9:0] ;default: 10'h0 ; */
/*description: This register controls the increase or decrease step scale for
high speed channel7.*/
#define LEDC_DUTY_SCALE_HSCH7 0x000003FF
#define LEDC_DUTY_SCALE_HSCH7_M ((LEDC_DUTY_SCALE_HSCH7_V)<<(LEDC_DUTY_SCALE_HSCH7_S))
#define LEDC_DUTY_SCALE_HSCH7_V 0x3FF
#define LEDC_DUTY_SCALE_HSCH7_S 0
#define LEDC_HSCH7_DUTY_R_REG (DR_REG_LEDC_BASE + 0x009C)
/* LEDC_DUTY_HSCH7 : RO ;bitpos:[24:0] ;default: 25'h0 ; */
/*description: This register represents the current duty of the output signal
for high speed channel7.*/
#define LEDC_DUTY_HSCH7 0x01FFFFFF
#define LEDC_DUTY_HSCH7_M ((LEDC_DUTY_HSCH7_V)<<(LEDC_DUTY_HSCH7_S))
#define LEDC_DUTY_HSCH7_V 0x1FFFFFF
#define LEDC_DUTY_HSCH7_S 0
#define LEDC_LSCH0_CONF0_REG (DR_REG_LEDC_BASE + 0x00A0)
/* LEDC_PARA_UP_LSCH0 : R/W ;bitpos:[4] ;default: 1'b0 ; */
/*description: This bit is used to update register LEDC_LSCH0_HPOINT and LEDC_LSCH0_DUTY
for low speed channel0.*/
#define LEDC_PARA_UP_LSCH0 (BIT(4))
#define LEDC_PARA_UP_LSCH0_M (BIT(4))
#define LEDC_PARA_UP_LSCH0_V 0x1
#define LEDC_PARA_UP_LSCH0_S 4
/* LEDC_IDLE_LV_LSCH0 : R/W ;bitpos:[3] ;default: 1'b0 ; */
/*description: This bit is used to control the output value when low speed channel0 is off.*/
#define LEDC_IDLE_LV_LSCH0 (BIT(3))
#define LEDC_IDLE_LV_LSCH0_M (BIT(3))
#define LEDC_IDLE_LV_LSCH0_V 0x1
#define LEDC_IDLE_LV_LSCH0_S 3
/* LEDC_SIG_OUT_EN_LSCH0 : R/W ;bitpos:[2] ;default: 1'b0 ; */
/*description: This is the output enable control bit for low speed channel0.*/
#define LEDC_SIG_OUT_EN_LSCH0 (BIT(2))
#define LEDC_SIG_OUT_EN_LSCH0_M (BIT(2))
#define LEDC_SIG_OUT_EN_LSCH0_V 0x1
#define LEDC_SIG_OUT_EN_LSCH0_S 2
/* LEDC_TIMER_SEL_LSCH0 : R/W ;bitpos:[1:0] ;default: 2'd0 ; */
/*description: There are four low speed timers the two bits are used to select
one of them for low speed channel0. 2'b00: seletc lstimer0. 2'b01: select lstimer1. 2'b10: select lstimer2. 2'b11: select lstimer3.*/
#define LEDC_TIMER_SEL_LSCH0 0x00000003
#define LEDC_TIMER_SEL_LSCH0_M ((LEDC_TIMER_SEL_LSCH0_V)<<(LEDC_TIMER_SEL_LSCH0_S))
#define LEDC_TIMER_SEL_LSCH0_V 0x3
#define LEDC_TIMER_SEL_LSCH0_S 0
#define LEDC_LSCH0_HPOINT_REG (DR_REG_LEDC_BASE + 0x00A4)
/* LEDC_HPOINT_LSCH0 : R/W ;bitpos:[19:0] ;default: 20'h0 ; */
/*description: The output value changes to high when lstimerx(x=[0 3]) selected
by low speed channel0 has reached reg_hpoint_lsch0[19:0]*/
#define LEDC_HPOINT_LSCH0 0x000FFFFF
#define LEDC_HPOINT_LSCH0_M ((LEDC_HPOINT_LSCH0_V)<<(LEDC_HPOINT_LSCH0_S))
#define LEDC_HPOINT_LSCH0_V 0xFFFFF
#define LEDC_HPOINT_LSCH0_S 0
#define LEDC_LSCH0_DUTY_REG (DR_REG_LEDC_BASE + 0x00A8)
/* LEDC_DUTY_LSCH0 : R/W ;bitpos:[24:0] ;default: 25'h0 ; */
/*description: The register is used to control output duty. When lstimerx(x=[0
3]) choosed by low speed channel0 has reached reg_lpoint_lsch0 the output signal changes to low. reg_lpoint_lsch0=(reg_hpoint_lsch0[19:0]+reg_duty_lsch0[24:4]) (1) reg_lpoint_lsch0=(reg_hpoint_lsch0[19:0]+reg_duty_lsch0[24:4] +1) (2) The least four bits in this register represent the decimal part and determines when to choose (1) or (2)*/
#define LEDC_DUTY_LSCH0 0x01FFFFFF
#define LEDC_DUTY_LSCH0_M ((LEDC_DUTY_LSCH0_V)<<(LEDC_DUTY_LSCH0_S))
#define LEDC_DUTY_LSCH0_V 0x1FFFFFF
#define LEDC_DUTY_LSCH0_S 0
#define LEDC_LSCH0_CONF1_REG (DR_REG_LEDC_BASE + 0x00AC)
/* LEDC_DUTY_START_LSCH0 : R/W ;bitpos:[31] ;default: 1'b0 ; */
/*description: When reg_duty_num_hsch1 reg_duty_cycle_hsch1 and reg_duty_scale_hsch1
has been configured. these register won't take effect until set reg_duty_start_hsch1. this bit is automatically cleared by hardware.*/
#define LEDC_DUTY_START_LSCH0 (BIT(31))
#define LEDC_DUTY_START_LSCH0_M (BIT(31))
#define LEDC_DUTY_START_LSCH0_V 0x1
#define LEDC_DUTY_START_LSCH0_S 31
/* LEDC_DUTY_INC_LSCH0 : R/W ;bitpos:[30] ;default: 1'b1 ; */
/*description: This register is used to increase the duty of output signal or
decrease the duty of output signal for low speed channel6.*/
#define LEDC_DUTY_INC_LSCH0 (BIT(30))
#define LEDC_DUTY_INC_LSCH0_M (BIT(30))
#define LEDC_DUTY_INC_LSCH0_V 0x1
#define LEDC_DUTY_INC_LSCH0_S 30
/* LEDC_DUTY_NUM_LSCH0 : R/W ;bitpos:[29:20] ;default: 10'h0 ; */
/*description: This register is used to control the num of increased or decreased
times for low speed channel6.*/
#define LEDC_DUTY_NUM_LSCH0 0x000003FF
#define LEDC_DUTY_NUM_LSCH0_M ((LEDC_DUTY_NUM_LSCH0_V)<<(LEDC_DUTY_NUM_LSCH0_S))
#define LEDC_DUTY_NUM_LSCH0_V 0x3FF
#define LEDC_DUTY_NUM_LSCH0_S 20
/* LEDC_DUTY_CYCLE_LSCH0 : R/W ;bitpos:[19:10] ;default: 10'h0 ; */
/*description: This register is used to increase or decrease the duty every
reg_duty_cycle_lsch0 cycles for low speed channel0.*/
#define LEDC_DUTY_CYCLE_LSCH0 0x000003FF
#define LEDC_DUTY_CYCLE_LSCH0_M ((LEDC_DUTY_CYCLE_LSCH0_V)<<(LEDC_DUTY_CYCLE_LSCH0_S))
#define LEDC_DUTY_CYCLE_LSCH0_V 0x3FF
#define LEDC_DUTY_CYCLE_LSCH0_S 10
/* LEDC_DUTY_SCALE_LSCH0 : R/W ;bitpos:[9:0] ;default: 10'h0 ; */
/*description: This register controls the increase or decrease step scale for
low speed channel0.*/
#define LEDC_DUTY_SCALE_LSCH0 0x000003FF
#define LEDC_DUTY_SCALE_LSCH0_M ((LEDC_DUTY_SCALE_LSCH0_V)<<(LEDC_DUTY_SCALE_LSCH0_S))
#define LEDC_DUTY_SCALE_LSCH0_V 0x3FF
#define LEDC_DUTY_SCALE_LSCH0_S 0
#define LEDC_LSCH0_DUTY_R_REG (DR_REG_LEDC_BASE + 0x00B0)
/* LEDC_DUTY_LSCH0 : RO ;bitpos:[24:0] ;default: 25'h0 ; */
/*description: This register represents the current duty of the output signal
for low speed channel0.*/
#define LEDC_DUTY_LSCH0 0x01FFFFFF
#define LEDC_DUTY_LSCH0_M ((LEDC_DUTY_LSCH0_V)<<(LEDC_DUTY_LSCH0_S))
#define LEDC_DUTY_LSCH0_V 0x1FFFFFF
#define LEDC_DUTY_LSCH0_S 0
#define LEDC_LSCH1_CONF0_REG (DR_REG_LEDC_BASE + 0x00B4)
/* LEDC_PARA_UP_LSCH1 : R/W ;bitpos:[4] ;default: 1'b0 ; */
/*description: This bit is used to update register LEDC_LSCH1_HPOINT and LEDC_LSCH1_DUTY
for low speed channel1.*/
#define LEDC_PARA_UP_LSCH1 (BIT(4))
#define LEDC_PARA_UP_LSCH1_M (BIT(4))
#define LEDC_PARA_UP_LSCH1_V 0x1
#define LEDC_PARA_UP_LSCH1_S 4
/* LEDC_IDLE_LV_LSCH1 : R/W ;bitpos:[3] ;default: 1'b0 ; */
/*description: This bit is used to control the output value when low speed channel1 is off.*/
#define LEDC_IDLE_LV_LSCH1 (BIT(3))
#define LEDC_IDLE_LV_LSCH1_M (BIT(3))
#define LEDC_IDLE_LV_LSCH1_V 0x1
#define LEDC_IDLE_LV_LSCH1_S 3
/* LEDC_SIG_OUT_EN_LSCH1 : R/W ;bitpos:[2] ;default: 1'b0 ; */
/*description: This is the output enable control bit for low speed channel1.*/
#define LEDC_SIG_OUT_EN_LSCH1 (BIT(2))
#define LEDC_SIG_OUT_EN_LSCH1_M (BIT(2))
#define LEDC_SIG_OUT_EN_LSCH1_V 0x1
#define LEDC_SIG_OUT_EN_LSCH1_S 2
/* LEDC_TIMER_SEL_LSCH1 : R/W ;bitpos:[1:0] ;default: 2'd0 ; */
/*description: There are four low speed timers the two bits are used to select
one of them for low speed channel1. 2'b00: seletc lstimer0. 2'b01: select lstimer1. 2'b10: select lstimer2. 2'b11: select lstimer3.*/
#define LEDC_TIMER_SEL_LSCH1 0x00000003
#define LEDC_TIMER_SEL_LSCH1_M ((LEDC_TIMER_SEL_LSCH1_V)<<(LEDC_TIMER_SEL_LSCH1_S))
#define LEDC_TIMER_SEL_LSCH1_V 0x3
#define LEDC_TIMER_SEL_LSCH1_S 0
#define LEDC_LSCH1_HPOINT_REG (DR_REG_LEDC_BASE + 0x00B8)
/* LEDC_HPOINT_LSCH1 : R/W ;bitpos:[19:0] ;default: 20'h0 ; */
/*description: The output value changes to high when lstimerx(x=[0 3]) selected
by low speed channel1 has reached reg_hpoint_lsch1[19:0]*/
#define LEDC_HPOINT_LSCH1 0x000FFFFF
#define LEDC_HPOINT_LSCH1_M ((LEDC_HPOINT_LSCH1_V)<<(LEDC_HPOINT_LSCH1_S))
#define LEDC_HPOINT_LSCH1_V 0xFFFFF
#define LEDC_HPOINT_LSCH1_S 0
#define LEDC_LSCH1_DUTY_REG (DR_REG_LEDC_BASE + 0x00BC)
/* LEDC_DUTY_LSCH1 : R/W ;bitpos:[24:0] ;default: 25'h0 ; */
/*description: The register is used to control output duty. When lstimerx(x=[0
3]) choosed by low speed channel1 has reached reg_lpoint_lsch1 the output signal changes to low. reg_lpoint_lsch1=(reg_hpoint_lsch1[19:0]+reg_duty_lsch1[24:4]) (1) reg_lpoint_lsch1=(reg_hpoint_lsch1[19:0]+reg_duty_lsch1[24:4] +1) (2) The least four bits in this register represent the decimal part and determines when to choose (1) or (2)*/
#define LEDC_DUTY_LSCH1 0x01FFFFFF
#define LEDC_DUTY_LSCH1_M ((LEDC_DUTY_LSCH1_V)<<(LEDC_DUTY_LSCH1_S))
#define LEDC_DUTY_LSCH1_V 0x1FFFFFF
#define LEDC_DUTY_LSCH1_S 0
#define LEDC_LSCH1_CONF1_REG (DR_REG_LEDC_BASE + 0x00C0)
/* LEDC_DUTY_START_LSCH1 : R/W ;bitpos:[31] ;default: 1'b0 ; */
/*description: When reg_duty_num_hsch1 reg_duty_cycle_hsch1 and reg_duty_scale_hsch1
has been configured. these register won't take effect until set reg_duty_start_hsch1. this bit is automatically cleared by hardware.*/
#define LEDC_DUTY_START_LSCH1 (BIT(31))
#define LEDC_DUTY_START_LSCH1_M (BIT(31))
#define LEDC_DUTY_START_LSCH1_V 0x1
#define LEDC_DUTY_START_LSCH1_S 31
/* LEDC_DUTY_INC_LSCH1 : R/W ;bitpos:[30] ;default: 1'b1 ; */
/*description: This register is used to increase the duty of output signal or
decrease the duty of output signal for low speed channel1.*/
#define LEDC_DUTY_INC_LSCH1 (BIT(30))
#define LEDC_DUTY_INC_LSCH1_M (BIT(30))
#define LEDC_DUTY_INC_LSCH1_V 0x1
#define LEDC_DUTY_INC_LSCH1_S 30
/* LEDC_DUTY_NUM_LSCH1 : R/W ;bitpos:[29:20] ;default: 10'h0 ; */
/*description: This register is used to control the num of increased or decreased
times for low speed channel1.*/
#define LEDC_DUTY_NUM_LSCH1 0x000003FF
#define LEDC_DUTY_NUM_LSCH1_M ((LEDC_DUTY_NUM_LSCH1_V)<<(LEDC_DUTY_NUM_LSCH1_S))
#define LEDC_DUTY_NUM_LSCH1_V 0x3FF
#define LEDC_DUTY_NUM_LSCH1_S 20
/* LEDC_DUTY_CYCLE_LSCH1 : R/W ;bitpos:[19:10] ;default: 10'h0 ; */
/*description: This register is used to increase or decrease the duty every
reg_duty_cycle_lsch1 cycles for low speed channel1.*/
#define LEDC_DUTY_CYCLE_LSCH1 0x000003FF
#define LEDC_DUTY_CYCLE_LSCH1_M ((LEDC_DUTY_CYCLE_LSCH1_V)<<(LEDC_DUTY_CYCLE_LSCH1_S))
#define LEDC_DUTY_CYCLE_LSCH1_V 0x3FF
#define LEDC_DUTY_CYCLE_LSCH1_S 10
/* LEDC_DUTY_SCALE_LSCH1 : R/W ;bitpos:[9:0] ;default: 10'h0 ; */
/*description: This register controls the increase or decrease step scale for
low speed channel1.*/
#define LEDC_DUTY_SCALE_LSCH1 0x000003FF
#define LEDC_DUTY_SCALE_LSCH1_M ((LEDC_DUTY_SCALE_LSCH1_V)<<(LEDC_DUTY_SCALE_LSCH1_S))
#define LEDC_DUTY_SCALE_LSCH1_V 0x3FF
#define LEDC_DUTY_SCALE_LSCH1_S 0
#define LEDC_LSCH1_DUTY_R_REG (DR_REG_LEDC_BASE + 0x00C4)
/* LEDC_DUTY_LSCH1 : RO ;bitpos:[24:0] ;default: 25'h0 ; */
/*description: This register represents the current duty of the output signal
for low speed channel1.*/
#define LEDC_DUTY_LSCH1 0x01FFFFFF
#define LEDC_DUTY_LSCH1_M ((LEDC_DUTY_LSCH1_V)<<(LEDC_DUTY_LSCH1_S))
#define LEDC_DUTY_LSCH1_V 0x1FFFFFF
#define LEDC_DUTY_LSCH1_S 0
#define LEDC_LSCH2_CONF0_REG (DR_REG_LEDC_BASE + 0x00C8)
/* LEDC_PARA_UP_LSCH2 : R/W ;bitpos:[4] ;default: 1'b0 ; */
/*description: This bit is used to update register LEDC_LSCH2_HPOINT and LEDC_LSCH2_DUTY
for low speed channel2.*/
#define LEDC_PARA_UP_LSCH2 (BIT(4))
#define LEDC_PARA_UP_LSCH2_M (BIT(4))
#define LEDC_PARA_UP_LSCH2_V 0x1
#define LEDC_PARA_UP_LSCH2_S 4
/* LEDC_IDLE_LV_LSCH2 : R/W ;bitpos:[3] ;default: 1'b0 ; */
/*description: This bit is used to control the output value when low speed channel2 is off.*/
#define LEDC_IDLE_LV_LSCH2 (BIT(3))
#define LEDC_IDLE_LV_LSCH2_M (BIT(3))
#define LEDC_IDLE_LV_LSCH2_V 0x1
#define LEDC_IDLE_LV_LSCH2_S 3
/* LEDC_SIG_OUT_EN_LSCH2 : R/W ;bitpos:[2] ;default: 1'b0 ; */
/*description: This is the output enable control bit for low speed channel2.*/
#define LEDC_SIG_OUT_EN_LSCH2 (BIT(2))
#define LEDC_SIG_OUT_EN_LSCH2_M (BIT(2))
#define LEDC_SIG_OUT_EN_LSCH2_V 0x1
#define LEDC_SIG_OUT_EN_LSCH2_S 2
/* LEDC_TIMER_SEL_LSCH2 : R/W ;bitpos:[1:0] ;default: 2'd0 ; */
/*description: There are four low speed timers the two bits are used to select
one of them for low speed channel2. 2'b00: seletc lstimer0. 2'b01: select lstimer1. 2'b10: select lstimer2. 2'b11: select lstimer3.*/
#define LEDC_TIMER_SEL_LSCH2 0x00000003
#define LEDC_TIMER_SEL_LSCH2_M ((LEDC_TIMER_SEL_LSCH2_V)<<(LEDC_TIMER_SEL_LSCH2_S))
#define LEDC_TIMER_SEL_LSCH2_V 0x3
#define LEDC_TIMER_SEL_LSCH2_S 0
#define LEDC_LSCH2_HPOINT_REG (DR_REG_LEDC_BASE + 0x00CC)
/* LEDC_HPOINT_LSCH2 : R/W ;bitpos:[19:0] ;default: 20'h0 ; */
/*description: The output value changes to high when lstimerx(x=[0 3]) selected
by low speed channel2 has reached reg_hpoint_lsch2[19:0]*/
#define LEDC_HPOINT_LSCH2 0x000FFFFF
#define LEDC_HPOINT_LSCH2_M ((LEDC_HPOINT_LSCH2_V)<<(LEDC_HPOINT_LSCH2_S))
#define LEDC_HPOINT_LSCH2_V 0xFFFFF
#define LEDC_HPOINT_LSCH2_S 0
#define LEDC_LSCH2_DUTY_REG (DR_REG_LEDC_BASE + 0x00D0)
/* LEDC_DUTY_LSCH2 : R/W ;bitpos:[24:0] ;default: 25'h0 ; */
/*description: The register is used to control output duty. When lstimerx(x=[0
3]) choosed by low speed channel2 has reached reg_lpoint_lsch2 the output signal changes to low. reg_lpoint_lsch2=(reg_hpoint_lsch2[19:0]+reg_duty_lsch2[24:4]) (1) reg_lpoint_lsch2=(reg_hpoint_lsch2[19:0]+reg_duty_lsch2[24:4] +1) (2) The least four bits in this register represent the decimal part and determines when to choose (1) or (2)*/
#define LEDC_DUTY_LSCH2 0x01FFFFFF
#define LEDC_DUTY_LSCH2_M ((LEDC_DUTY_LSCH2_V)<<(LEDC_DUTY_LSCH2_S))
#define LEDC_DUTY_LSCH2_V 0x1FFFFFF
#define LEDC_DUTY_LSCH2_S 0
#define LEDC_LSCH2_CONF1_REG (DR_REG_LEDC_BASE + 0x00D4)
/* LEDC_DUTY_START_LSCH2 : R/W ;bitpos:[31] ;default: 1'b0 ; */
/*description: When reg_duty_num_hsch2 reg_duty_cycle_hsch2 and reg_duty_scale_hsch2
has been configured. these register won't take effect until set reg_duty_start_hsch2. this bit is automatically cleared by hardware.*/
#define LEDC_DUTY_START_LSCH2 (BIT(31))
#define LEDC_DUTY_START_LSCH2_M (BIT(31))
#define LEDC_DUTY_START_LSCH2_V 0x1
#define LEDC_DUTY_START_LSCH2_S 31
/* LEDC_DUTY_INC_LSCH2 : R/W ;bitpos:[30] ;default: 1'b1 ; */
/*description: This register is used to increase the duty of output signal or
decrease the duty of output signal for low speed channel2.*/
#define LEDC_DUTY_INC_LSCH2 (BIT(30))
#define LEDC_DUTY_INC_LSCH2_M (BIT(30))
#define LEDC_DUTY_INC_LSCH2_V 0x1
#define LEDC_DUTY_INC_LSCH2_S 30
/* LEDC_DUTY_NUM_LSCH2 : R/W ;bitpos:[29:20] ;default: 10'h0 ; */
/*description: This register is used to control the num of increased or decreased
times for low speed channel2.*/
#define LEDC_DUTY_NUM_LSCH2 0x000003FF
#define LEDC_DUTY_NUM_LSCH2_M ((LEDC_DUTY_NUM_LSCH2_V)<<(LEDC_DUTY_NUM_LSCH2_S))
#define LEDC_DUTY_NUM_LSCH2_V 0x3FF
#define LEDC_DUTY_NUM_LSCH2_S 20
/* LEDC_DUTY_CYCLE_LSCH2 : R/W ;bitpos:[19:10] ;default: 10'h0 ; */
/*description: This register is used to increase or decrease the duty every
reg_duty_cycle_lsch2 cycles for low speed channel2.*/
#define LEDC_DUTY_CYCLE_LSCH2 0x000003FF
#define LEDC_DUTY_CYCLE_LSCH2_M ((LEDC_DUTY_CYCLE_LSCH2_V)<<(LEDC_DUTY_CYCLE_LSCH2_S))
#define LEDC_DUTY_CYCLE_LSCH2_V 0x3FF
#define LEDC_DUTY_CYCLE_LSCH2_S 10
/* LEDC_DUTY_SCALE_LSCH2 : R/W ;bitpos:[9:0] ;default: 10'h0 ; */
/*description: This register controls the increase or decrease step scale for
low speed channel2.*/
#define LEDC_DUTY_SCALE_LSCH2 0x000003FF
#define LEDC_DUTY_SCALE_LSCH2_M ((LEDC_DUTY_SCALE_LSCH2_V)<<(LEDC_DUTY_SCALE_LSCH2_S))
#define LEDC_DUTY_SCALE_LSCH2_V 0x3FF
#define LEDC_DUTY_SCALE_LSCH2_S 0
#define LEDC_LSCH2_DUTY_R_REG (DR_REG_LEDC_BASE + 0x00D8)
/* LEDC_DUTY_LSCH2 : RO ;bitpos:[24:0] ;default: 25'h0 ; */
/*description: This register represents the current duty of the output signal
for low speed channel2.*/
#define LEDC_DUTY_LSCH2 0x01FFFFFF
#define LEDC_DUTY_LSCH2_M ((LEDC_DUTY_LSCH2_V)<<(LEDC_DUTY_LSCH2_S))
#define LEDC_DUTY_LSCH2_V 0x1FFFFFF
#define LEDC_DUTY_LSCH2_S 0
#define LEDC_LSCH3_CONF0_REG (DR_REG_LEDC_BASE + 0x00DC)
/* LEDC_PARA_UP_LSCH3 : R/W ;bitpos:[4] ;default: 1'b0 ; */
/*description: This bit is used to update register LEDC_LSCH3_HPOINT and LEDC_LSCH3_DUTY
for low speed channel3.*/
#define LEDC_PARA_UP_LSCH3 (BIT(4))
#define LEDC_PARA_UP_LSCH3_M (BIT(4))
#define LEDC_PARA_UP_LSCH3_V 0x1
#define LEDC_PARA_UP_LSCH3_S 4
/* LEDC_IDLE_LV_LSCH3 : R/W ;bitpos:[3] ;default: 1'b0 ; */
/*description: This bit is used to control the output value when low speed channel3 is off.*/
#define LEDC_IDLE_LV_LSCH3 (BIT(3))
#define LEDC_IDLE_LV_LSCH3_M (BIT(3))
#define LEDC_IDLE_LV_LSCH3_V 0x1
#define LEDC_IDLE_LV_LSCH3_S 3
/* LEDC_SIG_OUT_EN_LSCH3 : R/W ;bitpos:[2] ;default: 1'b0 ; */
/*description: This is the output enable control bit for low speed channel3.*/
#define LEDC_SIG_OUT_EN_LSCH3 (BIT(2))
#define LEDC_SIG_OUT_EN_LSCH3_M (BIT(2))
#define LEDC_SIG_OUT_EN_LSCH3_V 0x1
#define LEDC_SIG_OUT_EN_LSCH3_S 2
/* LEDC_TIMER_SEL_LSCH3 : R/W ;bitpos:[1:0] ;default: 2'd0 ; */
/*description: There are four low speed timers the two bits are used to select
one of them for low speed channel3. 2'b00: seletc lstimer0. 2'b01: select lstimer1. 2'b10: select lstimer2. 2'b11: select lstimer3.*/
#define LEDC_TIMER_SEL_LSCH3 0x00000003
#define LEDC_TIMER_SEL_LSCH3_M ((LEDC_TIMER_SEL_LSCH3_V)<<(LEDC_TIMER_SEL_LSCH3_S))
#define LEDC_TIMER_SEL_LSCH3_V 0x3
#define LEDC_TIMER_SEL_LSCH3_S 0
#define LEDC_LSCH3_HPOINT_REG (DR_REG_LEDC_BASE + 0x00E0)
/* LEDC_HPOINT_LSCH3 : R/W ;bitpos:[19:0] ;default: 20'h0 ; */
/*description: The output value changes to high when lstimerx(x=[0 3]) selected
by low speed channel3 has reached reg_hpoint_lsch3[19:0]*/
#define LEDC_HPOINT_LSCH3 0x000FFFFF
#define LEDC_HPOINT_LSCH3_M ((LEDC_HPOINT_LSCH3_V)<<(LEDC_HPOINT_LSCH3_S))
#define LEDC_HPOINT_LSCH3_V 0xFFFFF
#define LEDC_HPOINT_LSCH3_S 0
#define LEDC_LSCH3_DUTY_REG (DR_REG_LEDC_BASE + 0x00E4)
/* LEDC_DUTY_LSCH3 : R/W ;bitpos:[24:0] ;default: 25'h0 ; */
/*description: The register is used to control output duty. When lstimerx(x=[0
3]) choosed by low speed channel3 has reached reg_lpoint_lsch3 the output signal changes to low. reg_lpoint_lsch3=(reg_hpoint_lsch3[19:0]+reg_duty_lsch3[24:4]) (1) reg_lpoint_lsch3=(reg_hpoint_lsch3[19:0]+reg_duty_lsch3[24:4] +1) (2) The least four bits in this register represent the decimal part and determines when to choose (1) or (2)*/
#define LEDC_DUTY_LSCH3 0x01FFFFFF
#define LEDC_DUTY_LSCH3_M ((LEDC_DUTY_LSCH3_V)<<(LEDC_DUTY_LSCH3_S))
#define LEDC_DUTY_LSCH3_V 0x1FFFFFF
#define LEDC_DUTY_LSCH3_S 0
#define LEDC_LSCH3_CONF1_REG (DR_REG_LEDC_BASE + 0x00E8)
/* LEDC_DUTY_START_LSCH3 : R/W ;bitpos:[31] ;default: 1'b0 ; */
/*description: When reg_duty_num_hsch3 reg_duty_cycle_hsch3 and reg_duty_scale_hsch3
has been configured. these register won't take effect until set reg_duty_start_hsch3. this bit is automatically cleared by hardware.*/
#define LEDC_DUTY_START_LSCH3 (BIT(31))
#define LEDC_DUTY_START_LSCH3_M (BIT(31))
#define LEDC_DUTY_START_LSCH3_V 0x1
#define LEDC_DUTY_START_LSCH3_S 31
/* LEDC_DUTY_INC_LSCH3 : R/W ;bitpos:[30] ;default: 1'b1 ; */
/*description: This register is used to increase the duty of output signal or
decrease the duty of output signal for low speed channel3.*/
#define LEDC_DUTY_INC_LSCH3 (BIT(30))
#define LEDC_DUTY_INC_LSCH3_M (BIT(30))
#define LEDC_DUTY_INC_LSCH3_V 0x1
#define LEDC_DUTY_INC_LSCH3_S 30
/* LEDC_DUTY_NUM_LSCH3 : R/W ;bitpos:[29:20] ;default: 10'h0 ; */
/*description: This register is used to control the num of increased or decreased
times for low speed channel3.*/
#define LEDC_DUTY_NUM_LSCH3 0x000003FF
#define LEDC_DUTY_NUM_LSCH3_M ((LEDC_DUTY_NUM_LSCH3_V)<<(LEDC_DUTY_NUM_LSCH3_S))
#define LEDC_DUTY_NUM_LSCH3_V 0x3FF
#define LEDC_DUTY_NUM_LSCH3_S 20
/* LEDC_DUTY_CYCLE_LSCH3 : R/W ;bitpos:[19:10] ;default: 10'h0 ; */
/*description: This register is used to increase or decrease the duty every
reg_duty_cycle_lsch3 cycles for low speed channel3.*/
#define LEDC_DUTY_CYCLE_LSCH3 0x000003FF
#define LEDC_DUTY_CYCLE_LSCH3_M ((LEDC_DUTY_CYCLE_LSCH3_V)<<(LEDC_DUTY_CYCLE_LSCH3_S))
#define LEDC_DUTY_CYCLE_LSCH3_V 0x3FF
#define LEDC_DUTY_CYCLE_LSCH3_S 10
/* LEDC_DUTY_SCALE_LSCH3 : R/W ;bitpos:[9:0] ;default: 10'h0 ; */
/*description: This register controls the increase or decrease step scale for
low speed channel3.*/
#define LEDC_DUTY_SCALE_LSCH3 0x000003FF
#define LEDC_DUTY_SCALE_LSCH3_M ((LEDC_DUTY_SCALE_LSCH3_V)<<(LEDC_DUTY_SCALE_LSCH3_S))
#define LEDC_DUTY_SCALE_LSCH3_V 0x3FF
#define LEDC_DUTY_SCALE_LSCH3_S 0
#define LEDC_LSCH3_DUTY_R_REG (DR_REG_LEDC_BASE + 0x00EC)
/* LEDC_DUTY_LSCH3 : RO ;bitpos:[24:0] ;default: 25'h0 ; */
/*description: This register represents the current duty of the output signal
for low speed channel3.*/
#define LEDC_DUTY_LSCH3 0x01FFFFFF
#define LEDC_DUTY_LSCH3_M ((LEDC_DUTY_LSCH3_V)<<(LEDC_DUTY_LSCH3_S))
#define LEDC_DUTY_LSCH3_V 0x1FFFFFF
#define LEDC_DUTY_LSCH3_S 0
#define LEDC_LSCH4_CONF0_REG (DR_REG_LEDC_BASE + 0x00F0)
/* LEDC_PARA_UP_LSCH4 : R/W ;bitpos:[4] ;default: 1'b0 ; */
/*description: This bit is used to update register LEDC_LSCH4_HPOINT and LEDC_LSCH4_DUTY
for low speed channel4.*/
#define LEDC_PARA_UP_LSCH4 (BIT(4))
#define LEDC_PARA_UP_LSCH4_M (BIT(4))
#define LEDC_PARA_UP_LSCH4_V 0x1
#define LEDC_PARA_UP_LSCH4_S 4
/* LEDC_IDLE_LV_LSCH4 : R/W ;bitpos:[3] ;default: 1'b0 ; */
/*description: This bit is used to control the output value when low speed channel4 is off.*/
#define LEDC_IDLE_LV_LSCH4 (BIT(3))
#define LEDC_IDLE_LV_LSCH4_M (BIT(3))
#define LEDC_IDLE_LV_LSCH4_V 0x1
#define LEDC_IDLE_LV_LSCH4_S 3
/* LEDC_SIG_OUT_EN_LSCH4 : R/W ;bitpos:[2] ;default: 1'b0 ; */
/*description: This is the output enable control bit for low speed channel4.*/
#define LEDC_SIG_OUT_EN_LSCH4 (BIT(2))
#define LEDC_SIG_OUT_EN_LSCH4_M (BIT(2))
#define LEDC_SIG_OUT_EN_LSCH4_V 0x1
#define LEDC_SIG_OUT_EN_LSCH4_S 2
/* LEDC_TIMER_SEL_LSCH4 : R/W ;bitpos:[1:0] ;default: 2'd0 ; */
/*description: There are four low speed timers the two bits are used to select
one of them for low speed channel4. 2'b00: seletc lstimer0. 2'b01: select lstimer1. 2'b10: select lstimer2. 2'b11: select lstimer3.*/
#define LEDC_TIMER_SEL_LSCH4 0x00000003
#define LEDC_TIMER_SEL_LSCH4_M ((LEDC_TIMER_SEL_LSCH4_V)<<(LEDC_TIMER_SEL_LSCH4_S))
#define LEDC_TIMER_SEL_LSCH4_V 0x3
#define LEDC_TIMER_SEL_LSCH4_S 0
#define LEDC_LSCH4_HPOINT_REG (DR_REG_LEDC_BASE + 0x00F4)
/* LEDC_HPOINT_LSCH4 : R/W ;bitpos:[19:0] ;default: 20'h0 ; */
/*description: The output value changes to high when lstimerx(x=[0 3]) selected
by low speed channel4 has reached reg_hpoint_lsch4[19:0]*/
#define LEDC_HPOINT_LSCH4 0x000FFFFF
#define LEDC_HPOINT_LSCH4_M ((LEDC_HPOINT_LSCH4_V)<<(LEDC_HPOINT_LSCH4_S))
#define LEDC_HPOINT_LSCH4_V 0xFFFFF
#define LEDC_HPOINT_LSCH4_S 0
#define LEDC_LSCH4_DUTY_REG (DR_REG_LEDC_BASE + 0x00F8)
/* LEDC_DUTY_LSCH4 : R/W ;bitpos:[24:0] ;default: 25'h0 ; */
/*description: The register is used to control output duty. When lstimerx(x=[0
3]) choosed by low speed channel4 has reached reg_lpoint_lsch4 the output signal changes to low. reg_lpoint_lsch4=(reg_hpoint_lsch4[19:0]+reg_duty_lsch4[24:4]) (1) reg_lpoint_lsch4=(reg_hpoint_lsch4[19:0]+reg_duty_lsch4[24:4] +1) (2) The least four bits in this register represent the decimal part and determines when to choose (1) or (2)*/
#define LEDC_DUTY_LSCH4 0x01FFFFFF
#define LEDC_DUTY_LSCH4_M ((LEDC_DUTY_LSCH4_V)<<(LEDC_DUTY_LSCH4_S))
#define LEDC_DUTY_LSCH4_V 0x1FFFFFF
#define LEDC_DUTY_LSCH4_S 0
#define LEDC_LSCH4_CONF1_REG (DR_REG_LEDC_BASE + 0x00FC)
/* LEDC_DUTY_START_LSCH4 : R/W ;bitpos:[31] ;default: 1'b0 ; */
/*description: When reg_duty_num_hsch4 reg_duty_cycle_hsch4 and reg_duty_scale_hsch4
has been configured. these register won't take effect until set reg_duty_start_hsch4. this bit is automatically cleared by hardware.*/
#define LEDC_DUTY_START_LSCH4 (BIT(31))
#define LEDC_DUTY_START_LSCH4_M (BIT(31))
#define LEDC_DUTY_START_LSCH4_V 0x1
#define LEDC_DUTY_START_LSCH4_S 31
/* LEDC_DUTY_INC_LSCH4 : R/W ;bitpos:[30] ;default: 1'b1 ; */
/*description: This register is used to increase the duty of output signal or
decrease the duty of output signal for low speed channel4.*/
#define LEDC_DUTY_INC_LSCH4 (BIT(30))
#define LEDC_DUTY_INC_LSCH4_M (BIT(30))
#define LEDC_DUTY_INC_LSCH4_V 0x1
#define LEDC_DUTY_INC_LSCH4_S 30
/* LEDC_DUTY_NUM_LSCH4 : R/W ;bitpos:[29:20] ;default: 10'h0 ; */
/*description: This register is used to control the num of increased or decreased
times for low speed channel4.*/
#define LEDC_DUTY_NUM_LSCH4 0x000003FF
#define LEDC_DUTY_NUM_LSCH4_M ((LEDC_DUTY_NUM_LSCH4_V)<<(LEDC_DUTY_NUM_LSCH4_S))
#define LEDC_DUTY_NUM_LSCH4_V 0x3FF
#define LEDC_DUTY_NUM_LSCH4_S 20
/* LEDC_DUTY_CYCLE_LSCH4 : R/W ;bitpos:[19:10] ;default: 10'h0 ; */
/*description: This register is used to increase or decrease the duty every
reg_duty_cycle_lsch4 cycles for low speed channel4.*/
#define LEDC_DUTY_CYCLE_LSCH4 0x000003FF
#define LEDC_DUTY_CYCLE_LSCH4_M ((LEDC_DUTY_CYCLE_LSCH4_V)<<(LEDC_DUTY_CYCLE_LSCH4_S))
#define LEDC_DUTY_CYCLE_LSCH4_V 0x3FF
#define LEDC_DUTY_CYCLE_LSCH4_S 10
/* LEDC_DUTY_SCALE_LSCH4 : R/W ;bitpos:[9:0] ;default: 10'h0 ; */
/*description: This register controls the increase or decrease step scale for
low speed channel4.*/
#define LEDC_DUTY_SCALE_LSCH4 0x000003FF
#define LEDC_DUTY_SCALE_LSCH4_M ((LEDC_DUTY_SCALE_LSCH4_V)<<(LEDC_DUTY_SCALE_LSCH4_S))
#define LEDC_DUTY_SCALE_LSCH4_V 0x3FF
#define LEDC_DUTY_SCALE_LSCH4_S 0
#define LEDC_LSCH4_DUTY_R_REG (DR_REG_LEDC_BASE + 0x0100)
/* LEDC_DUTY_LSCH4 : RO ;bitpos:[24:0] ;default: 25'h0 ; */
/*description: This register represents the current duty of the output signal
for low speed channel4.*/
#define LEDC_DUTY_LSCH4 0x01FFFFFF
#define LEDC_DUTY_LSCH4_M ((LEDC_DUTY_LSCH4_V)<<(LEDC_DUTY_LSCH4_S))
#define LEDC_DUTY_LSCH4_V 0x1FFFFFF
#define LEDC_DUTY_LSCH4_S 0
#define LEDC_LSCH5_CONF0_REG (DR_REG_LEDC_BASE + 0x0104)
/* LEDC_PARA_UP_LSCH5 : R/W ;bitpos:[4] ;default: 1'b0 ; */
/*description: This bit is used to update register LEDC_LSCH5_HPOINT and LEDC_LSCH5_DUTY
for low speed channel5.*/
#define LEDC_PARA_UP_LSCH5 (BIT(4))
#define LEDC_PARA_UP_LSCH5_M (BIT(4))
#define LEDC_PARA_UP_LSCH5_V 0x1
#define LEDC_PARA_UP_LSCH5_S 4
/* LEDC_IDLE_LV_LSCH5 : R/W ;bitpos:[3] ;default: 1'b0 ; */
/*description: This bit is used to control the output value when low speed channel5 is off.*/
#define LEDC_IDLE_LV_LSCH5 (BIT(3))
#define LEDC_IDLE_LV_LSCH5_M (BIT(3))
#define LEDC_IDLE_LV_LSCH5_V 0x1
#define LEDC_IDLE_LV_LSCH5_S 3
/* LEDC_SIG_OUT_EN_LSCH5 : R/W ;bitpos:[2] ;default: 1'b0 ; */
/*description: This is the output enable control bit for low speed channel5.*/
#define LEDC_SIG_OUT_EN_LSCH5 (BIT(2))
#define LEDC_SIG_OUT_EN_LSCH5_M (BIT(2))
#define LEDC_SIG_OUT_EN_LSCH5_V 0x1
#define LEDC_SIG_OUT_EN_LSCH5_S 2
/* LEDC_TIMER_SEL_LSCH5 : R/W ;bitpos:[1:0] ;default: 2'd0 ; */
/*description: There are four low speed timers the two bits are used to select
one of them for low speed channel5. 2'b00: seletc lstimer0. 2'b01: select lstimer1. 2'b10: select lstimer2. 2'b11: select lstimer3.*/
#define LEDC_TIMER_SEL_LSCH5 0x00000003
#define LEDC_TIMER_SEL_LSCH5_M ((LEDC_TIMER_SEL_LSCH5_V)<<(LEDC_TIMER_SEL_LSCH5_S))
#define LEDC_TIMER_SEL_LSCH5_V 0x3
#define LEDC_TIMER_SEL_LSCH5_S 0
#define LEDC_LSCH5_HPOINT_REG (DR_REG_LEDC_BASE + 0x0108)
/* LEDC_HPOINT_LSCH5 : R/W ;bitpos:[19:0] ;default: 20'h0 ; */
/*description: The output value changes to high when lstimerx(x=[0 3]) selected
by low speed channel5 has reached reg_hpoint_lsch5[19:0]*/
#define LEDC_HPOINT_LSCH5 0x000FFFFF
#define LEDC_HPOINT_LSCH5_M ((LEDC_HPOINT_LSCH5_V)<<(LEDC_HPOINT_LSCH5_S))
#define LEDC_HPOINT_LSCH5_V 0xFFFFF
#define LEDC_HPOINT_LSCH5_S 0
#define LEDC_LSCH5_DUTY_REG (DR_REG_LEDC_BASE + 0x010C)
/* LEDC_DUTY_LSCH5 : R/W ;bitpos:[24:0] ;default: 25'h0 ; */
/*description: The register is used to control output duty. When lstimerx(x=[0
3]) choosed by low speed channel5 has reached reg_lpoint_lsch5 the output signal changes to low. reg_lpoint_lsch5=(reg_hpoint_lsch5[19:0]+reg_duty_lsch5[24:4]) (1) reg_lpoint_lsch5=(reg_hpoint_lsch5[19:0]+reg_duty_lsch5[24:4] +1) (2) The least four bits in this register represent the decimal part and determines when to choose (1) or (2)*/
#define LEDC_DUTY_LSCH5 0x01FFFFFF
#define LEDC_DUTY_LSCH5_M ((LEDC_DUTY_LSCH5_V)<<(LEDC_DUTY_LSCH5_S))
#define LEDC_DUTY_LSCH5_V 0x1FFFFFF
#define LEDC_DUTY_LSCH5_S 0
#define LEDC_LSCH5_CONF1_REG (DR_REG_LEDC_BASE + 0x0110)
/* LEDC_DUTY_START_LSCH5 : R/W ;bitpos:[31] ;default: 1'b0 ; */
/*description: When reg_duty_num_hsch4 reg_duty_cycle_hsch4 and reg_duty_scale_hsch4
has been configured. these register won't take effect until set reg_duty_start_hsch4. this bit is automatically cleared by hardware.*/
#define LEDC_DUTY_START_LSCH5 (BIT(31))
#define LEDC_DUTY_START_LSCH5_M (BIT(31))
#define LEDC_DUTY_START_LSCH5_V 0x1
#define LEDC_DUTY_START_LSCH5_S 31
/* LEDC_DUTY_INC_LSCH5 : R/W ;bitpos:[30] ;default: 1'b1 ; */
/*description: This register is used to increase the duty of output signal or
decrease the duty of output signal for low speed channel5.*/
#define LEDC_DUTY_INC_LSCH5 (BIT(30))
#define LEDC_DUTY_INC_LSCH5_M (BIT(30))
#define LEDC_DUTY_INC_LSCH5_V 0x1
#define LEDC_DUTY_INC_LSCH5_S 30
/* LEDC_DUTY_NUM_LSCH5 : R/W ;bitpos:[29:20] ;default: 10'h0 ; */
/*description: This register is used to control the num of increased or decreased
times for low speed channel5.*/
#define LEDC_DUTY_NUM_LSCH5 0x000003FF
#define LEDC_DUTY_NUM_LSCH5_M ((LEDC_DUTY_NUM_LSCH5_V)<<(LEDC_DUTY_NUM_LSCH5_S))
#define LEDC_DUTY_NUM_LSCH5_V 0x3FF
#define LEDC_DUTY_NUM_LSCH5_S 20
/* LEDC_DUTY_CYCLE_LSCH5 : R/W ;bitpos:[19:10] ;default: 10'h0 ; */
/*description: This register is used to increase or decrease the duty every
reg_duty_cycle_lsch5 cycles for low speed channel4.*/
#define LEDC_DUTY_CYCLE_LSCH5 0x000003FF
#define LEDC_DUTY_CYCLE_LSCH5_M ((LEDC_DUTY_CYCLE_LSCH5_V)<<(LEDC_DUTY_CYCLE_LSCH5_S))
#define LEDC_DUTY_CYCLE_LSCH5_V 0x3FF
#define LEDC_DUTY_CYCLE_LSCH5_S 10
/* LEDC_DUTY_SCALE_LSCH5 : R/W ;bitpos:[9:0] ;default: 10'h0 ; */
/*description: This register controls the increase or decrease step scale for
low speed channel5.*/
#define LEDC_DUTY_SCALE_LSCH5 0x000003FF
#define LEDC_DUTY_SCALE_LSCH5_M ((LEDC_DUTY_SCALE_LSCH5_V)<<(LEDC_DUTY_SCALE_LSCH5_S))
#define LEDC_DUTY_SCALE_LSCH5_V 0x3FF
#define LEDC_DUTY_SCALE_LSCH5_S 0
#define LEDC_LSCH5_DUTY_R_REG (DR_REG_LEDC_BASE + 0x0114)
/* LEDC_DUTY_LSCH5 : RO ;bitpos:[24:0] ;default: 25'h0 ; */
/*description: This register represents the current duty of the output signal
for low speed channel5.*/
#define LEDC_DUTY_LSCH5 0x01FFFFFF
#define LEDC_DUTY_LSCH5_M ((LEDC_DUTY_LSCH5_V)<<(LEDC_DUTY_LSCH5_S))
#define LEDC_DUTY_LSCH5_V 0x1FFFFFF
#define LEDC_DUTY_LSCH5_S 0
#define LEDC_LSCH6_CONF0_REG (DR_REG_LEDC_BASE + 0x0118)
/* LEDC_PARA_UP_LSCH6 : R/W ;bitpos:[4] ;default: 1'b0 ; */
/*description: This bit is used to update register LEDC_LSCH6_HPOINT and LEDC_LSCH6_DUTY
for low speed channel6.*/
#define LEDC_PARA_UP_LSCH6 (BIT(4))
#define LEDC_PARA_UP_LSCH6_M (BIT(4))
#define LEDC_PARA_UP_LSCH6_V 0x1
#define LEDC_PARA_UP_LSCH6_S 4
/* LEDC_IDLE_LV_LSCH6 : R/W ;bitpos:[3] ;default: 1'b0 ; */
/*description: This bit is used to control the output value when low speed channel6 is off.*/
#define LEDC_IDLE_LV_LSCH6 (BIT(3))
#define LEDC_IDLE_LV_LSCH6_M (BIT(3))
#define LEDC_IDLE_LV_LSCH6_V 0x1
#define LEDC_IDLE_LV_LSCH6_S 3
/* LEDC_SIG_OUT_EN_LSCH6 : R/W ;bitpos:[2] ;default: 1'b0 ; */
/*description: This is the output enable control bit for low speed channel6.*/
#define LEDC_SIG_OUT_EN_LSCH6 (BIT(2))
#define LEDC_SIG_OUT_EN_LSCH6_M (BIT(2))
#define LEDC_SIG_OUT_EN_LSCH6_V 0x1
#define LEDC_SIG_OUT_EN_LSCH6_S 2
/* LEDC_TIMER_SEL_LSCH6 : R/W ;bitpos:[1:0] ;default: 2'd0 ; */
/*description: There are four low speed timers the two bits are used to select
one of them for low speed channel6. 2'b00: seletc lstimer0. 2'b01: select lstimer1. 2'b10: select lstimer2. 2'b11: select lstimer3.*/
#define LEDC_TIMER_SEL_LSCH6 0x00000003
#define LEDC_TIMER_SEL_LSCH6_M ((LEDC_TIMER_SEL_LSCH6_V)<<(LEDC_TIMER_SEL_LSCH6_S))
#define LEDC_TIMER_SEL_LSCH6_V 0x3
#define LEDC_TIMER_SEL_LSCH6_S 0
#define LEDC_LSCH6_HPOINT_REG (DR_REG_LEDC_BASE + 0x011C)
/* LEDC_HPOINT_LSCH6 : R/W ;bitpos:[19:0] ;default: 20'h0 ; */
/*description: The output value changes to high when lstimerx(x=[0 3]) selected
by low speed channel6 has reached reg_hpoint_lsch6[19:0]*/
#define LEDC_HPOINT_LSCH6 0x000FFFFF
#define LEDC_HPOINT_LSCH6_M ((LEDC_HPOINT_LSCH6_V)<<(LEDC_HPOINT_LSCH6_S))
#define LEDC_HPOINT_LSCH6_V 0xFFFFF
#define LEDC_HPOINT_LSCH6_S 0
#define LEDC_LSCH6_DUTY_REG (DR_REG_LEDC_BASE + 0x0120)
/* LEDC_DUTY_LSCH6 : R/W ;bitpos:[24:0] ;default: 25'h0 ; */
/*description: The register is used to control output duty. When lstimerx(x=[0
3]) choosed by low speed channel6 has reached reg_lpoint_lsch6 the output signal changes to low. reg_lpoint_lsch6=(reg_hpoint_lsch6[19:0]+reg_duty_lsch6[24:4]) (1) reg_lpoint_lsch6=(reg_hpoint_lsch6[19:0]+reg_duty_lsch6[24:4] +1) (2) The least four bits in this register represent the decimal part and determines when to choose (1) or (2)*/
#define LEDC_DUTY_LSCH6 0x01FFFFFF
#define LEDC_DUTY_LSCH6_M ((LEDC_DUTY_LSCH6_V)<<(LEDC_DUTY_LSCH6_S))
#define LEDC_DUTY_LSCH6_V 0x1FFFFFF
#define LEDC_DUTY_LSCH6_S 0
#define LEDC_LSCH6_CONF1_REG (DR_REG_LEDC_BASE + 0x0124)
/* LEDC_DUTY_START_LSCH6 : R/W ;bitpos:[31] ;default: 1'b0 ; */
/*description: When reg_duty_num_hsch6 reg_duty_cycle_hsch6 and reg_duty_scale_hsch6
has been configured. these register won't take effect until set reg_duty_start_hsch6. this bit is automatically cleared by hardware.*/
#define LEDC_DUTY_START_LSCH6 (BIT(31))
#define LEDC_DUTY_START_LSCH6_M (BIT(31))
#define LEDC_DUTY_START_LSCH6_V 0x1
#define LEDC_DUTY_START_LSCH6_S 31
/* LEDC_DUTY_INC_LSCH6 : R/W ;bitpos:[30] ;default: 1'b1 ; */
/*description: This register is used to increase the duty of output signal or
decrease the duty of output signal for low speed channel6.*/
#define LEDC_DUTY_INC_LSCH6 (BIT(30))
#define LEDC_DUTY_INC_LSCH6_M (BIT(30))
#define LEDC_DUTY_INC_LSCH6_V 0x1
#define LEDC_DUTY_INC_LSCH6_S 30
/* LEDC_DUTY_NUM_LSCH6 : R/W ;bitpos:[29:20] ;default: 10'h0 ; */
/*description: This register is used to control the num of increased or decreased
times for low speed channel6.*/
#define LEDC_DUTY_NUM_LSCH6 0x000003FF
#define LEDC_DUTY_NUM_LSCH6_M ((LEDC_DUTY_NUM_LSCH6_V)<<(LEDC_DUTY_NUM_LSCH6_S))
#define LEDC_DUTY_NUM_LSCH6_V 0x3FF
#define LEDC_DUTY_NUM_LSCH6_S 20
/* LEDC_DUTY_CYCLE_LSCH6 : R/W ;bitpos:[19:10] ;default: 10'h0 ; */
/*description: This register is used to increase or decrease the duty every
reg_duty_cycle_lsch6 cycles for low speed channel6.*/
#define LEDC_DUTY_CYCLE_LSCH6 0x000003FF
#define LEDC_DUTY_CYCLE_LSCH6_M ((LEDC_DUTY_CYCLE_LSCH6_V)<<(LEDC_DUTY_CYCLE_LSCH6_S))
#define LEDC_DUTY_CYCLE_LSCH6_V 0x3FF
#define LEDC_DUTY_CYCLE_LSCH6_S 10
/* LEDC_DUTY_SCALE_LSCH6 : R/W ;bitpos:[9:0] ;default: 10'h0 ; */
/*description: This register controls the increase or decrease step scale for
low speed channel6.*/
#define LEDC_DUTY_SCALE_LSCH6 0x000003FF
#define LEDC_DUTY_SCALE_LSCH6_M ((LEDC_DUTY_SCALE_LSCH6_V)<<(LEDC_DUTY_SCALE_LSCH6_S))
#define LEDC_DUTY_SCALE_LSCH6_V 0x3FF
#define LEDC_DUTY_SCALE_LSCH6_S 0
#define LEDC_LSCH6_DUTY_R_REG (DR_REG_LEDC_BASE + 0x0128)
/* LEDC_DUTY_LSCH6 : RO ;bitpos:[24:0] ;default: 25'h0 ; */
/*description: This register represents the current duty of the output signal
for low speed channel6.*/
#define LEDC_DUTY_LSCH6 0x01FFFFFF
#define LEDC_DUTY_LSCH6_M ((LEDC_DUTY_LSCH6_V)<<(LEDC_DUTY_LSCH6_S))
#define LEDC_DUTY_LSCH6_V 0x1FFFFFF
#define LEDC_DUTY_LSCH6_S 0
#define LEDC_LSCH7_CONF0_REG (DR_REG_LEDC_BASE + 0x012C)
/* LEDC_PARA_UP_LSCH7 : R/W ;bitpos:[4] ;default: 1'b0 ; */
/*description: This bit is used to update register LEDC_LSCH7_HPOINT and LEDC_LSCH7_DUTY
for low speed channel7.*/
#define LEDC_PARA_UP_LSCH7 (BIT(4))
#define LEDC_PARA_UP_LSCH7_M (BIT(4))
#define LEDC_PARA_UP_LSCH7_V 0x1
#define LEDC_PARA_UP_LSCH7_S 4
/* LEDC_IDLE_LV_LSCH7 : R/W ;bitpos:[3] ;default: 1'b0 ; */
/*description: This bit is used to control the output value when low speed channel7 is off.*/
#define LEDC_IDLE_LV_LSCH7 (BIT(3))
#define LEDC_IDLE_LV_LSCH7_M (BIT(3))
#define LEDC_IDLE_LV_LSCH7_V 0x1
#define LEDC_IDLE_LV_LSCH7_S 3
/* LEDC_SIG_OUT_EN_LSCH7 : R/W ;bitpos:[2] ;default: 1'b0 ; */
/*description: This is the output enable control bit for low speed channel7.*/
#define LEDC_SIG_OUT_EN_LSCH7 (BIT(2))
#define LEDC_SIG_OUT_EN_LSCH7_M (BIT(2))
#define LEDC_SIG_OUT_EN_LSCH7_V 0x1
#define LEDC_SIG_OUT_EN_LSCH7_S 2
/* LEDC_TIMER_SEL_LSCH7 : R/W ;bitpos:[1:0] ;default: 2'd0 ; */
/*description: There are four low speed timers the two bits are used to select
one of them for low speed channel7. 2'b00: seletc lstimer0. 2'b01: select lstimer1. 2'b10: select lstimer2. 2'b11: select lstimer3.*/
#define LEDC_TIMER_SEL_LSCH7 0x00000003
#define LEDC_TIMER_SEL_LSCH7_M ((LEDC_TIMER_SEL_LSCH7_V)<<(LEDC_TIMER_SEL_LSCH7_S))
#define LEDC_TIMER_SEL_LSCH7_V 0x3
#define LEDC_TIMER_SEL_LSCH7_S 0
#define LEDC_LSCH7_HPOINT_REG (DR_REG_LEDC_BASE + 0x0130)
/* LEDC_HPOINT_LSCH7 : R/W ;bitpos:[19:0] ;default: 20'h0 ; */
/*description: The output value changes to high when lstimerx(x=[0 3]) selected
by low speed channel7 has reached reg_hpoint_lsch7[19:0]*/
#define LEDC_HPOINT_LSCH7 0x000FFFFF
#define LEDC_HPOINT_LSCH7_M ((LEDC_HPOINT_LSCH7_V)<<(LEDC_HPOINT_LSCH7_S))
#define LEDC_HPOINT_LSCH7_V 0xFFFFF
#define LEDC_HPOINT_LSCH7_S 0
#define LEDC_LSCH7_DUTY_REG (DR_REG_LEDC_BASE + 0x0134)
/* LEDC_DUTY_LSCH7 : R/W ;bitpos:[24:0] ;default: 25'h0 ; */
/*description: The register is used to control output duty. When lstimerx(x=[0
3]) choosed by low speed channel7 has reached reg_lpoint_lsch7 the output signal changes to low. reg_lpoint_lsch7=(reg_hpoint_lsch7[19:0]+reg_duty_lsch7[24:4]) (1) reg_lpoint_lsch7=(reg_hpoint_lsch7[19:0]+reg_duty_lsch7[24:4] +1) (2) The least four bits in this register represent the decimal part and determines when to choose (1) or (2)*/
#define LEDC_DUTY_LSCH7 0x01FFFFFF
#define LEDC_DUTY_LSCH7_M ((LEDC_DUTY_LSCH7_V)<<(LEDC_DUTY_LSCH7_S))
#define LEDC_DUTY_LSCH7_V 0x1FFFFFF
#define LEDC_DUTY_LSCH7_S 0
#define LEDC_LSCH7_CONF1_REG (DR_REG_LEDC_BASE + 0x0138)
/* LEDC_DUTY_START_LSCH7 : R/W ;bitpos:[31] ;default: 1'b0 ; */
/*description: When reg_duty_num_hsch4 reg_duty_cycle_hsch4 and reg_duty_scale_hsch4
has been configured. these register won't take effect until set reg_duty_start_hsch4. this bit is automatically cleared by hardware.*/
#define LEDC_DUTY_START_LSCH7 (BIT(31))
#define LEDC_DUTY_START_LSCH7_M (BIT(31))
#define LEDC_DUTY_START_LSCH7_V 0x1
#define LEDC_DUTY_START_LSCH7_S 31
/* LEDC_DUTY_INC_LSCH7 : R/W ;bitpos:[30] ;default: 1'b1 ; */
/*description: This register is used to increase the duty of output signal or
decrease the duty of output signal for low speed channel4.*/
#define LEDC_DUTY_INC_LSCH7 (BIT(30))
#define LEDC_DUTY_INC_LSCH7_M (BIT(30))
#define LEDC_DUTY_INC_LSCH7_V 0x1
#define LEDC_DUTY_INC_LSCH7_S 30
/* LEDC_DUTY_NUM_LSCH7 : R/W ;bitpos:[29:20] ;default: 10'h0 ; */
/*description: This register is used to control the num of increased or decreased
times for low speed channel4.*/
#define LEDC_DUTY_NUM_LSCH7 0x000003FF
#define LEDC_DUTY_NUM_LSCH7_M ((LEDC_DUTY_NUM_LSCH7_V)<<(LEDC_DUTY_NUM_LSCH7_S))
#define LEDC_DUTY_NUM_LSCH7_V 0x3FF
#define LEDC_DUTY_NUM_LSCH7_S 20
/* LEDC_DUTY_CYCLE_LSCH7 : R/W ;bitpos:[19:10] ;default: 10'h0 ; */
/*description: This register is used to increase or decrease the duty every
reg_duty_cycle_lsch7 cycles for low speed channel7.*/
#define LEDC_DUTY_CYCLE_LSCH7 0x000003FF
#define LEDC_DUTY_CYCLE_LSCH7_M ((LEDC_DUTY_CYCLE_LSCH7_V)<<(LEDC_DUTY_CYCLE_LSCH7_S))
#define LEDC_DUTY_CYCLE_LSCH7_V 0x3FF
#define LEDC_DUTY_CYCLE_LSCH7_S 10
/* LEDC_DUTY_SCALE_LSCH7 : R/W ;bitpos:[9:0] ;default: 10'h0 ; */
/*description: This register controls the increase or decrease step scale for
low speed channel7.*/
#define LEDC_DUTY_SCALE_LSCH7 0x000003FF
#define LEDC_DUTY_SCALE_LSCH7_M ((LEDC_DUTY_SCALE_LSCH7_V)<<(LEDC_DUTY_SCALE_LSCH7_S))
#define LEDC_DUTY_SCALE_LSCH7_V 0x3FF
#define LEDC_DUTY_SCALE_LSCH7_S 0
#define LEDC_LSCH7_DUTY_R_REG (DR_REG_LEDC_BASE + 0x013C)
/* LEDC_DUTY_LSCH7 : RO ;bitpos:[24:0] ;default: 25'h0 ; */
/*description: This register represents the current duty of the output signal
for low speed channel7.*/
#define LEDC_DUTY_LSCH7 0x01FFFFFF
#define LEDC_DUTY_LSCH7_M ((LEDC_DUTY_LSCH7_V)<<(LEDC_DUTY_LSCH7_S))
#define LEDC_DUTY_LSCH7_V 0x1FFFFFF
#define LEDC_DUTY_LSCH7_S 0
#define LEDC_HSTIMER0_CONF_REG (DR_REG_LEDC_BASE + 0x0140)
/* LEDC_TICK_SEL_HSTIMER0 : R/W ;bitpos:[25] ;default: 1'b0 ; */
/*description: This bit is used to choose apb_clk or ref_tick for high speed
timer0. 1'b1:apb_clk 0:ref_tick*/
#define LEDC_TICK_SEL_HSTIMER0 (BIT(25))
#define LEDC_TICK_SEL_HSTIMER0_M (BIT(25))
#define LEDC_TICK_SEL_HSTIMER0_V 0x1
#define LEDC_TICK_SEL_HSTIMER0_S 25
/* LEDC_HSTIMER0_RST : R/W ;bitpos:[24] ;default: 1'b1 ; */
/*description: This bit is used to reset high speed timer0 the counter will be 0 after reset.*/
#define LEDC_HSTIMER0_RST (BIT(24))
#define LEDC_HSTIMER0_RST_M (BIT(24))
#define LEDC_HSTIMER0_RST_V 0x1
#define LEDC_HSTIMER0_RST_S 24
/* LEDC_HSTIMER0_PAUSE : R/W ;bitpos:[23] ;default: 1'b0 ; */
/*description: This bit is used to pause the counter in high speed timer0*/
#define LEDC_HSTIMER0_PAUSE (BIT(23))
#define LEDC_HSTIMER0_PAUSE_M (BIT(23))
#define LEDC_HSTIMER0_PAUSE_V 0x1
#define LEDC_HSTIMER0_PAUSE_S 23
/* LEDC_DIV_NUM_HSTIMER0 : R/W ;bitpos:[22:5] ;default: 18'h0 ; */
/*description: This register is used to configure parameter for divider in high
speed timer0 the least significant eight bits represent the decimal part.*/
#define LEDC_DIV_NUM_HSTIMER0 0x0003FFFF
#define LEDC_DIV_NUM_HSTIMER0_M ((LEDC_DIV_NUM_HSTIMER0_V)<<(LEDC_DIV_NUM_HSTIMER0_S))
#define LEDC_DIV_NUM_HSTIMER0_V 0x3FFFF
#define LEDC_DIV_NUM_HSTIMER0_S 5
/* LEDC_HSTIMER0_LIM : R/W ;bitpos:[4:0] ;default: 5'h0 ; */
/*description: This register controls the range of the counter in high speed
timer0. the counter range is [0 2**reg_hstimer0_lim] the max bit width for counter is 20.*/
#define LEDC_HSTIMER0_DUTY_RES 0x0000001F
#define LEDC_HSTIMER0_DUTY_RES_M ((LEDC_HSTIMER0_DUTY_RES_V)<<(LEDC_HSTIMER0_DUTY_RES_S))
#define LEDC_HSTIMER0_DUTY_RES_V 0x1F
#define LEDC_HSTIMER0_DUTY_RES_S 0
// Keep the definitions below to be compatible with previous version
#define LEDC_HSTIMER0_LIM LEDC_HSTIMER0_DUTY_RES
#define LEDC_HSTIMER0_LIM_M LEDC_HSTIMER0_DUTY_RES_M
#define LEDC_HSTIMER0_LIM_V LEDC_HSTIMER0_DUTY_RES_V
#define LEDC_HSTIMER0_LIM_S LEDC_HSTIMER0_DUTY_RES_S
#define LEDC_HSTIMER0_VALUE_REG (DR_REG_LEDC_BASE + 0x0144)
/* LEDC_HSTIMER0_CNT : RO ;bitpos:[19:0] ;default: 20'b0 ; */
/*description: software can read this register to get the current counter value
in high speed timer0*/
#define LEDC_HSTIMER0_CNT 0x000FFFFF
#define LEDC_HSTIMER0_CNT_M ((LEDC_HSTIMER0_CNT_V)<<(LEDC_HSTIMER0_CNT_S))
#define LEDC_HSTIMER0_CNT_V 0xFFFFF
#define LEDC_HSTIMER0_CNT_S 0
#define LEDC_HSTIMER1_CONF_REG (DR_REG_LEDC_BASE + 0x0148)
/* LEDC_TICK_SEL_HSTIMER1 : R/W ;bitpos:[25] ;default: 1'b0 ; */
/*description: This bit is used to choose apb_clk or ref_tick for high speed
timer1. 1'b1:apb_clk 0:ref_tick*/
#define LEDC_TICK_SEL_HSTIMER1 (BIT(25))
#define LEDC_TICK_SEL_HSTIMER1_M (BIT(25))
#define LEDC_TICK_SEL_HSTIMER1_V 0x1
#define LEDC_TICK_SEL_HSTIMER1_S 25
/* LEDC_HSTIMER1_RST : R/W ;bitpos:[24] ;default: 1'b1 ; */
/*description: This bit is used to reset high speed timer1 the counter will be 0 after reset.*/
#define LEDC_HSTIMER1_RST (BIT(24))
#define LEDC_HSTIMER1_RST_M (BIT(24))
#define LEDC_HSTIMER1_RST_V 0x1
#define LEDC_HSTIMER1_RST_S 24
/* LEDC_HSTIMER1_PAUSE : R/W ;bitpos:[23] ;default: 1'b0 ; */
/*description: This bit is used to pause the counter in high speed timer1*/
#define LEDC_HSTIMER1_PAUSE (BIT(23))
#define LEDC_HSTIMER1_PAUSE_M (BIT(23))
#define LEDC_HSTIMER1_PAUSE_V 0x1
#define LEDC_HSTIMER1_PAUSE_S 23
/* LEDC_DIV_NUM_HSTIMER1 : R/W ;bitpos:[22:5] ;default: 18'h0 ; */
/*description: This register is used to configure parameter for divider in high
speed timer1 the least significant eight bits represent the decimal part.*/
#define LEDC_DIV_NUM_HSTIMER1 0x0003FFFF
#define LEDC_DIV_NUM_HSTIMER1_M ((LEDC_DIV_NUM_HSTIMER1_V)<<(LEDC_DIV_NUM_HSTIMER1_S))
#define LEDC_DIV_NUM_HSTIMER1_V 0x3FFFF
#define LEDC_DIV_NUM_HSTIMER1_S 5
/* LEDC_HSTIMER1_LIM : R/W ;bitpos:[4:0] ;default: 5'h0 ; */
/*description: This register controls the range of the counter in high speed
timer1. the counter range is [0 2**reg_hstimer1_lim] the max bit width for counter is 20.*/
#define LEDC_HSTIMER1_DUTY_RES 0x0000001F
#define LEDC_HSTIMER1_DUTY_RES_M ((LEDC_HSTIMER1_DUTY_RES_V)<<(LEDC_HSTIMER1_DUTY_RES_S))
#define LEDC_HSTIMER1_DUTY_RES_V 0x1F
#define LEDC_HSTIMER1_DUTY_RES_S 0
// Keep the definitions below to be compatible with previous version
#define LEDC_HSTIMER1_LIM LEDC_HSTIMER1_DUTY_RES
#define LEDC_HSTIMER1_LIM_M LEDC_HSTIMER1_DUTY_RES_M
#define LEDC_HSTIMER1_LIM_V LEDC_HSTIMER1_DUTY_RES_V
#define LEDC_HSTIMER1_LIM_S LEDC_HSTIMER1_DUTY_RES_S
#define LEDC_HSTIMER1_VALUE_REG (DR_REG_LEDC_BASE + 0x014C)
/* LEDC_HSTIMER1_CNT : RO ;bitpos:[19:0] ;default: 20'b0 ; */
/*description: software can read this register to get the current counter value
in high speed timer1.*/
#define LEDC_HSTIMER1_CNT 0x000FFFFF
#define LEDC_HSTIMER1_CNT_M ((LEDC_HSTIMER1_CNT_V)<<(LEDC_HSTIMER1_CNT_S))
#define LEDC_HSTIMER1_CNT_V 0xFFFFF
#define LEDC_HSTIMER1_CNT_S 0
#define LEDC_HSTIMER2_CONF_REG (DR_REG_LEDC_BASE + 0x0150)
/* LEDC_TICK_SEL_HSTIMER2 : R/W ;bitpos:[25] ;default: 1'b0 ; */
/*description: This bit is used to choose apb_clk or ref_tick for high speed
timer2. 1'b1:apb_clk 0:ref_tick*/
#define LEDC_TICK_SEL_HSTIMER2 (BIT(25))
#define LEDC_TICK_SEL_HSTIMER2_M (BIT(25))
#define LEDC_TICK_SEL_HSTIMER2_V 0x1
#define LEDC_TICK_SEL_HSTIMER2_S 25
/* LEDC_HSTIMER2_RST : R/W ;bitpos:[24] ;default: 1'b1 ; */
/*description: This bit is used to reset high speed timer2 the counter will be 0 after reset.*/
#define LEDC_HSTIMER2_RST (BIT(24))
#define LEDC_HSTIMER2_RST_M (BIT(24))
#define LEDC_HSTIMER2_RST_V 0x1
#define LEDC_HSTIMER2_RST_S 24
/* LEDC_HSTIMER2_PAUSE : R/W ;bitpos:[23] ;default: 1'b0 ; */
/*description: This bit is used to pause the counter in high speed timer2*/
#define LEDC_HSTIMER2_PAUSE (BIT(23))
#define LEDC_HSTIMER2_PAUSE_M (BIT(23))
#define LEDC_HSTIMER2_PAUSE_V 0x1
#define LEDC_HSTIMER2_PAUSE_S 23
/* LEDC_DIV_NUM_HSTIMER2 : R/W ;bitpos:[22:5] ;default: 18'h0 ; */
/*description: This register is used to configure parameter for divider in high
speed timer2 the least significant eight bits represent the decimal part.*/
#define LEDC_DIV_NUM_HSTIMER2 0x0003FFFF
#define LEDC_DIV_NUM_HSTIMER2_M ((LEDC_DIV_NUM_HSTIMER2_V)<<(LEDC_DIV_NUM_HSTIMER2_S))
#define LEDC_DIV_NUM_HSTIMER2_V 0x3FFFF
#define LEDC_DIV_NUM_HSTIMER2_S 5
/* LEDC_HSTIMER2_LIM : R/W ;bitpos:[4:0] ;default: 5'h0 ; */
/*description: This register controls the range of the counter in high speed
timer2. the counter range is [0 2**reg_hstimer2_lim] the max bit width for counter is 20.*/
#define LEDC_HSTIMER2_DUTY_RES 0x0000001F
#define LEDC_HSTIMER2_DUTY_RES_M ((LEDC_HSTIMER2_DUTY_RES_V)<<(LEDC_HSTIMER2_DUTY_RES_S))
#define LEDC_HSTIMER2_DUTY_RES_V 0x1F
#define LEDC_HSTIMER2_DUTY_RES_S 0
// Keep the definitions below to be compatible with previous version
#define LEDC_HSTIMER2_LIM LEDC_HSTIMER2_DUTY_RES
#define LEDC_HSTIMER2_LIM_M LEDC_HSTIMER2_DUTY_RES_M
#define LEDC_HSTIMER2_LIM_V LEDC_HSTIMER2_DUTY_RES_V
#define LEDC_HSTIMER2_LIM_S LEDC_HSTIMER2_DUTY_RES_S
#define LEDC_HSTIMER2_VALUE_REG (DR_REG_LEDC_BASE + 0x0154)
/* LEDC_HSTIMER2_CNT : RO ;bitpos:[19:0] ;default: 20'b0 ; */
/*description: software can read this register to get the current counter value
in high speed timer2*/
#define LEDC_HSTIMER2_CNT 0x000FFFFF
#define LEDC_HSTIMER2_CNT_M ((LEDC_HSTIMER2_CNT_V)<<(LEDC_HSTIMER2_CNT_S))
#define LEDC_HSTIMER2_CNT_V 0xFFFFF
#define LEDC_HSTIMER2_CNT_S 0
#define LEDC_HSTIMER3_CONF_REG (DR_REG_LEDC_BASE + 0x0158)
/* LEDC_TICK_SEL_HSTIMER3 : R/W ;bitpos:[25] ;default: 1'b0 ; */
/*description: This bit is used to choose apb_clk or ref_tick for high speed
timer3. 1'b1:apb_clk 0:ref_tick*/
#define LEDC_TICK_SEL_HSTIMER3 (BIT(25))
#define LEDC_TICK_SEL_HSTIMER3_M (BIT(25))
#define LEDC_TICK_SEL_HSTIMER3_V 0x1
#define LEDC_TICK_SEL_HSTIMER3_S 25
/* LEDC_HSTIMER3_RST : R/W ;bitpos:[24] ;default: 1'b1 ; */
/*description: This bit is used to reset high speed timer3 the counter will be 0 after reset.*/
#define LEDC_HSTIMER3_RST (BIT(24))
#define LEDC_HSTIMER3_RST_M (BIT(24))
#define LEDC_HSTIMER3_RST_V 0x1
#define LEDC_HSTIMER3_RST_S 24
/* LEDC_HSTIMER3_PAUSE : R/W ;bitpos:[23] ;default: 1'b0 ; */
/*description: This bit is used to pause the counter in high speed timer3*/
#define LEDC_HSTIMER3_PAUSE (BIT(23))
#define LEDC_HSTIMER3_PAUSE_M (BIT(23))
#define LEDC_HSTIMER3_PAUSE_V 0x1
#define LEDC_HSTIMER3_PAUSE_S 23
/* LEDC_DIV_NUM_HSTIMER3 : R/W ;bitpos:[22:5] ;default: 18'h0 ; */
/*description: This register is used to configure parameter for divider in high
speed timer3 the least significant eight bits represent the decimal part.*/
#define LEDC_DIV_NUM_HSTIMER3 0x0003FFFF
#define LEDC_DIV_NUM_HSTIMER3_M ((LEDC_DIV_NUM_HSTIMER3_V)<<(LEDC_DIV_NUM_HSTIMER3_S))
#define LEDC_DIV_NUM_HSTIMER3_V 0x3FFFF
#define LEDC_DIV_NUM_HSTIMER3_S 5
/* LEDC_HSTIMER3_LIM : R/W ;bitpos:[4:0] ;default: 5'h0 ; */
/*description: This register controls the range of the counter in high speed
timer3. the counter range is [0 2**reg_hstimer3_lim] the max bit width for counter is 20.*/
#define LEDC_HSTIMER3_DUTY_RES 0x0000001F
#define LEDC_HSTIMER3_DUTY_RES_M ((LEDC_HSTIMER3_DUTY_RES_V)<<(LEDC_HSTIMER3_DUTY_RES_S))
#define LEDC_HSTIMER3_DUTY_RES_V 0x1F
#define LEDC_HSTIMER3_DUTY_RES_S 0
// Keep the definitions below to be compatible with previous version
#define LEDC_HSTIMER3_LIM LEDC_HSTIMER3_DUTY_RES
#define LEDC_HSTIMER3_LIM_M LEDC_HSTIMER3_DUTY_RES_M
#define LEDC_HSTIMER3_LIM_V LEDC_HSTIMER3_DUTY_RES_V
#define LEDC_HSTIMER3_LIM_S LEDC_HSTIMER3_DUTY_RES_S
#define LEDC_HSTIMER3_VALUE_REG (DR_REG_LEDC_BASE + 0x015C)
/* LEDC_HSTIMER3_CNT : RO ;bitpos:[19:0] ;default: 20'b0 ; */
/*description: software can read this register to get the current counter value
in high speed timer3*/
#define LEDC_HSTIMER3_CNT 0x000FFFFF
#define LEDC_HSTIMER3_CNT_M ((LEDC_HSTIMER3_CNT_V)<<(LEDC_HSTIMER3_CNT_S))
#define LEDC_HSTIMER3_CNT_V 0xFFFFF
#define LEDC_HSTIMER3_CNT_S 0
#define LEDC_LSTIMER0_CONF_REG (DR_REG_LEDC_BASE + 0x0160)
/* LEDC_LSTIMER0_PARA_UP : R/W ;bitpos:[26] ;default: 1'h0 ; */
/*description: Set this bit to update reg_div_num_lstime0 and reg_lstimer0_lim.*/
#define LEDC_LSTIMER0_PARA_UP (BIT(26))
#define LEDC_LSTIMER0_PARA_UP_M (BIT(26))
#define LEDC_LSTIMER0_PARA_UP_V 0x1
#define LEDC_LSTIMER0_PARA_UP_S 26
/* LEDC_TICK_SEL_LSTIMER0 : R/W ;bitpos:[25] ;default: 1'b0 ; */
/*description: This bit is used to choose slow_clk or ref_tick for low speed
timer0. 1'b1:slow_clk 0:ref_tick*/
#define LEDC_TICK_SEL_LSTIMER0 (BIT(25))
#define LEDC_TICK_SEL_LSTIMER0_M (BIT(25))
#define LEDC_TICK_SEL_LSTIMER0_V 0x1
#define LEDC_TICK_SEL_LSTIMER0_S 25
/* LEDC_LSTIMER0_RST : R/W ;bitpos:[24] ;default: 1'b1 ; */
/*description: This bit is used to reset low speed timer0 the counter will be 0 after reset.*/
#define LEDC_LSTIMER0_RST (BIT(24))
#define LEDC_LSTIMER0_RST_M (BIT(24))
#define LEDC_LSTIMER0_RST_V 0x1
#define LEDC_LSTIMER0_RST_S 24
/* LEDC_LSTIMER0_PAUSE : R/W ;bitpos:[23] ;default: 1'b0 ; */
/*description: This bit is used to pause the counter in low speed timer0.*/
#define LEDC_LSTIMER0_PAUSE (BIT(23))
#define LEDC_LSTIMER0_PAUSE_M (BIT(23))
#define LEDC_LSTIMER0_PAUSE_V 0x1
#define LEDC_LSTIMER0_PAUSE_S 23
/* LEDC_DIV_NUM_LSTIMER0 : R/W ;bitpos:[22:5] ;default: 18'h0 ; */
/*description: This register is used to configure parameter for divider in low
speed timer0 the least significant eight bits represent the decimal part.*/
#define LEDC_DIV_NUM_LSTIMER0 0x0003FFFF
#define LEDC_DIV_NUM_LSTIMER0_M ((LEDC_DIV_NUM_LSTIMER0_V)<<(LEDC_DIV_NUM_LSTIMER0_S))
#define LEDC_DIV_NUM_LSTIMER0_V 0x3FFFF
#define LEDC_DIV_NUM_LSTIMER0_S 5
/* LEDC_LSTIMER0_LIM : R/W ;bitpos:[4:0] ;default: 5'h0 ; */
/*description: This register controls the range of the counter in low speed
timer0. the counter range is [0 2**reg_lstimer0_lim] the max bit width for counter is 20.*/
#define LEDC_LSTIMER0_DUTY_RES 0x0000001F
#define LEDC_LSTIMER0_DUTY_RES_M ((LEDC_LSTIMER0_DUTY_RES_V)<<(LEDC_LSTIMER0_DUTY_RES_S))
#define LEDC_LSTIMER0_DUTY_RES_V 0x1F
#define LEDC_LSTIMER0_DUTY_RES_S 0
// Keep the definitions below to be compatible with previous version
#define LEDC_LSTIMER0_LIM LEDC_LSTIMER0_DUTY_RES
#define LEDC_LSTIMER0_LIM_M LEDC_LSTIMER0_DUTY_RES_M
#define LEDC_LSTIMER0_LIM_V LEDC_LSTIMER0_DUTY_RES_V
#define LEDC_LSTIMER0_LIM_S LEDC_LSTIMER0_DUTY_RES_S
#define LEDC_LSTIMER0_VALUE_REG (DR_REG_LEDC_BASE + 0x0164)
/* LEDC_LSTIMER0_CNT : RO ;bitpos:[19:0] ;default: 20'b0 ; */
/*description: software can read this register to get the current counter value
in low speed timer0.*/
#define LEDC_LSTIMER0_CNT 0x000FFFFF
#define LEDC_LSTIMER0_CNT_M ((LEDC_LSTIMER0_CNT_V)<<(LEDC_LSTIMER0_CNT_S))
#define LEDC_LSTIMER0_CNT_V 0xFFFFF
#define LEDC_LSTIMER0_CNT_S 0
#define LEDC_LSTIMER1_CONF_REG (DR_REG_LEDC_BASE + 0x0168)
/* LEDC_LSTIMER1_PARA_UP : R/W ;bitpos:[26] ;default: 1'h0 ; */
/*description: Set this bit to update reg_div_num_lstime1 and reg_lstimer1_lim.*/
#define LEDC_LSTIMER1_PARA_UP (BIT(26))
#define LEDC_LSTIMER1_PARA_UP_M (BIT(26))
#define LEDC_LSTIMER1_PARA_UP_V 0x1
#define LEDC_LSTIMER1_PARA_UP_S 26
/* LEDC_TICK_SEL_LSTIMER1 : R/W ;bitpos:[25] ;default: 1'b0 ; */
/*description: This bit is used to choose slow_clk or ref_tick for low speed
timer1. 1'b1:slow_clk 0:ref_tick*/
#define LEDC_TICK_SEL_LSTIMER1 (BIT(25))
#define LEDC_TICK_SEL_LSTIMER1_M (BIT(25))
#define LEDC_TICK_SEL_LSTIMER1_V 0x1
#define LEDC_TICK_SEL_LSTIMER1_S 25
/* LEDC_LSTIMER1_RST : R/W ;bitpos:[24] ;default: 1'b1 ; */
/*description: This bit is used to reset low speed timer1 the counter will be 0 after reset.*/
#define LEDC_LSTIMER1_RST (BIT(24))
#define LEDC_LSTIMER1_RST_M (BIT(24))
#define LEDC_LSTIMER1_RST_V 0x1
#define LEDC_LSTIMER1_RST_S 24
/* LEDC_LSTIMER1_PAUSE : R/W ;bitpos:[23] ;default: 1'b0 ; */
/*description: This bit is used to pause the counter in low speed timer1.*/
#define LEDC_LSTIMER1_PAUSE (BIT(23))
#define LEDC_LSTIMER1_PAUSE_M (BIT(23))
#define LEDC_LSTIMER1_PAUSE_V 0x1
#define LEDC_LSTIMER1_PAUSE_S 23
/* LEDC_DIV_NUM_LSTIMER1 : R/W ;bitpos:[22:5] ;default: 18'h0 ; */
/*description: This register is used to configure parameter for divider in low
speed timer1 the least significant eight bits represent the decimal part.*/
#define LEDC_DIV_NUM_LSTIMER1 0x0003FFFF
#define LEDC_DIV_NUM_LSTIMER1_M ((LEDC_DIV_NUM_LSTIMER1_V)<<(LEDC_DIV_NUM_LSTIMER1_S))
#define LEDC_DIV_NUM_LSTIMER1_V 0x3FFFF
#define LEDC_DIV_NUM_LSTIMER1_S 5
/* LEDC_LSTIMER1_LIM : R/W ;bitpos:[4:0] ;default: 5'h0 ; */
/*description: This register controls the range of the counter in low speed
timer1. the counter range is [0 2**reg_lstimer1_lim] the max bit width for counter is 20.*/
#define LEDC_LSTIMER1_DUTY_RES 0x0000001F
#define LEDC_LSTIMER1_DUTY_RES_M ((LEDC_LSTIMER1_DUTY_RES_V)<<(LEDC_LSTIMER1_DUTY_RES_S))
#define LEDC_LSTIMER1_DUTY_RES_V 0x1F
#define LEDC_LSTIMER1_DUTY_RES_S 0
// Keep the definitions below to be compatible with previous version
#define LEDC_LSTIMER1_LIM LEDC_LSTIMER1_DUTY_RES
#define LEDC_LSTIMER1_LIM_M LEDC_LSTIMER1_DUTY_RES_M
#define LEDC_LSTIMER1_LIM_V LEDC_LSTIMER1_DUTY_RES_V
#define LEDC_LSTIMER1_LIM_S LEDC_LSTIMER1_DUTY_RES_S
#define LEDC_LSTIMER1_VALUE_REG (DR_REG_LEDC_BASE + 0x016C)
/* LEDC_LSTIMER1_CNT : RO ;bitpos:[19:0] ;default: 20'b0 ; */
/*description: software can read this register to get the current counter value
in low speed timer1.*/
#define LEDC_LSTIMER1_CNT 0x000FFFFF
#define LEDC_LSTIMER1_CNT_M ((LEDC_LSTIMER1_CNT_V)<<(LEDC_LSTIMER1_CNT_S))
#define LEDC_LSTIMER1_CNT_V 0xFFFFF
#define LEDC_LSTIMER1_CNT_S 0
#define LEDC_LSTIMER2_CONF_REG (DR_REG_LEDC_BASE + 0x0170)
/* LEDC_LSTIMER2_PARA_UP : R/W ;bitpos:[26] ;default: 1'h0 ; */
/*description: Set this bit to update reg_div_num_lstime2 and reg_lstimer2_lim.*/
#define LEDC_LSTIMER2_PARA_UP (BIT(26))
#define LEDC_LSTIMER2_PARA_UP_M (BIT(26))
#define LEDC_LSTIMER2_PARA_UP_V 0x1
#define LEDC_LSTIMER2_PARA_UP_S 26
/* LEDC_TICK_SEL_LSTIMER2 : R/W ;bitpos:[25] ;default: 1'b0 ; */
/*description: This bit is used to choose slow_clk or ref_tick for low speed
timer2. 1'b1:slow_clk 0:ref_tick*/
#define LEDC_TICK_SEL_LSTIMER2 (BIT(25))
#define LEDC_TICK_SEL_LSTIMER2_M (BIT(25))
#define LEDC_TICK_SEL_LSTIMER2_V 0x1
#define LEDC_TICK_SEL_LSTIMER2_S 25
/* LEDC_LSTIMER2_RST : R/W ;bitpos:[24] ;default: 1'b1 ; */
/*description: This bit is used to reset low speed timer2 the counter will be 0 after reset.*/
#define LEDC_LSTIMER2_RST (BIT(24))
#define LEDC_LSTIMER2_RST_M (BIT(24))
#define LEDC_LSTIMER2_RST_V 0x1
#define LEDC_LSTIMER2_RST_S 24
/* LEDC_LSTIMER2_PAUSE : R/W ;bitpos:[23] ;default: 1'b0 ; */
/*description: This bit is used to pause the counter in low speed timer2.*/
#define LEDC_LSTIMER2_PAUSE (BIT(23))
#define LEDC_LSTIMER2_PAUSE_M (BIT(23))
#define LEDC_LSTIMER2_PAUSE_V 0x1
#define LEDC_LSTIMER2_PAUSE_S 23
/* LEDC_DIV_NUM_LSTIMER2 : R/W ;bitpos:[22:5] ;default: 18'h0 ; */
/*description: This register is used to configure parameter for divider in low
speed timer2 the least significant eight bits represent the decimal part.*/
#define LEDC_DIV_NUM_LSTIMER2 0x0003FFFF
#define LEDC_DIV_NUM_LSTIMER2_M ((LEDC_DIV_NUM_LSTIMER2_V)<<(LEDC_DIV_NUM_LSTIMER2_S))
#define LEDC_DIV_NUM_LSTIMER2_V 0x3FFFF
#define LEDC_DIV_NUM_LSTIMER2_S 5
/* LEDC_LSTIMER2_LIM : R/W ;bitpos:[4:0] ;default: 5'h0 ; */
/*description: This register controls the range of the counter in low speed
timer2. the counter range is [0 2**reg_lstimer2_lim] the max bit width for counter is 20.*/
#define LEDC_LSTIMER2_DUTY_RES 0x0000001F
#define LEDC_LSTIMER2_DUTY_RES_M ((LEDC_LSTIMER2_DUTY_RES_V)<<(LEDC_LSTIMER2_DUTY_RES_S))
#define LEDC_LSTIMER2_DUTY_RES_V 0x1F
#define LEDC_LSTIMER2_DUTY_RES_S 0
// Keep the definitions below to be compatible with previous version
#define LEDC_LSTIMER2_LIM LEDC_LSTIMER2_DUTY_RES
#define LEDC_LSTIMER2_LIM_M LEDC_LSTIMER2_DUTY_RES_M
#define LEDC_LSTIMER2_LIM_V LEDC_LSTIMER2_DUTY_RES_V
#define LEDC_LSTIMER2_LIM_S LEDC_LSTIMER2_DUTY_RES_S
#define LEDC_LSTIMER2_VALUE_REG (DR_REG_LEDC_BASE + 0x0174)
/* LEDC_LSTIMER2_CNT : RO ;bitpos:[19:0] ;default: 20'b0 ; */
/*description: software can read this register to get the current counter value
in low speed timer2.*/
#define LEDC_LSTIMER2_CNT 0x000FFFFF
#define LEDC_LSTIMER2_CNT_M ((LEDC_LSTIMER2_CNT_V)<<(LEDC_LSTIMER2_CNT_S))
#define LEDC_LSTIMER2_CNT_V 0xFFFFF
#define LEDC_LSTIMER2_CNT_S 0
#define LEDC_LSTIMER3_CONF_REG (DR_REG_LEDC_BASE + 0x0178)
/* LEDC_LSTIMER3_PARA_UP : R/W ;bitpos:[26] ;default: 1'h0 ; */
/*description: Set this bit to update reg_div_num_lstime3 and reg_lstimer3_lim.*/
#define LEDC_LSTIMER3_PARA_UP (BIT(26))
#define LEDC_LSTIMER3_PARA_UP_M (BIT(26))
#define LEDC_LSTIMER3_PARA_UP_V 0x1
#define LEDC_LSTIMER3_PARA_UP_S 26
/* LEDC_TICK_SEL_LSTIMER3 : R/W ;bitpos:[25] ;default: 1'b0 ; */
/*description: This bit is used to choose slow_clk or ref_tick for low speed
timer3. 1'b1:slow_clk 0:ref_tick*/
#define LEDC_TICK_SEL_LSTIMER3 (BIT(25))
#define LEDC_TICK_SEL_LSTIMER3_M (BIT(25))
#define LEDC_TICK_SEL_LSTIMER3_V 0x1
#define LEDC_TICK_SEL_LSTIMER3_S 25
/* LEDC_LSTIMER3_RST : R/W ;bitpos:[24] ;default: 1'b1 ; */
/*description: This bit is used to reset low speed timer3 the counter will be 0 after reset.*/
#define LEDC_LSTIMER3_RST (BIT(24))
#define LEDC_LSTIMER3_RST_M (BIT(24))
#define LEDC_LSTIMER3_RST_V 0x1
#define LEDC_LSTIMER3_RST_S 24
/* LEDC_LSTIMER3_PAUSE : R/W ;bitpos:[23] ;default: 1'b0 ; */
/*description: This bit is used to pause the counter in low speed timer3.*/
#define LEDC_LSTIMER3_PAUSE (BIT(23))
#define LEDC_LSTIMER3_PAUSE_M (BIT(23))
#define LEDC_LSTIMER3_PAUSE_V 0x1
#define LEDC_LSTIMER3_PAUSE_S 23
/* LEDC_DIV_NUM_LSTIMER3 : R/W ;bitpos:[22:5] ;default: 18'h0 ; */
/*description: This register is used to configure parameter for divider in low
speed timer3 the least significant eight bits represent the decimal part.*/
#define LEDC_DIV_NUM_LSTIMER3 0x0003FFFF
#define LEDC_DIV_NUM_LSTIMER3_M ((LEDC_DIV_NUM_LSTIMER3_V)<<(LEDC_DIV_NUM_LSTIMER3_S))
#define LEDC_DIV_NUM_LSTIMER3_V 0x3FFFF
#define LEDC_DIV_NUM_LSTIMER3_S 5
/* LEDC_LSTIMER3_LIM : R/W ;bitpos:[4:0] ;default: 5'h0 ; */
/*description: This register controls the range of the counter in low speed
timer3. the counter range is [0 2**reg_lstimer3_lim] the max bit width for counter is 20.*/
#define LEDC_LSTIMER3_DUTY_RES 0x0000001F
#define LEDC_LSTIMER3_DUTY_RES_M ((LEDC_LSTIMER3_DUTY_RES_V)<<(LEDC_LSTIMER3_DUTY_RES_S))
#define LEDC_LSTIMER3_DUTY_RES_V 0x1F
#define LEDC_LSTIMER3_DUTY_RES_S 0
// Keep the definitions below to be compatible with previous version
#define LEDC_LSTIMER3_LIM LEDC_LSTIMER3_DUTY_RES
#define LEDC_LSTIMER3_LIM_M LEDC_LSTIMER3_DUTY_RES_M
#define LEDC_LSTIMER3_LIM_V LEDC_LSTIMER3_DUTY_RES_V
#define LEDC_LSTIMER3_LIM_S LEDC_LSTIMER3_DUTY_RES_S
#define LEDC_LSTIMER3_VALUE_REG (DR_REG_LEDC_BASE + 0x017C)
/* LEDC_LSTIMER3_CNT : RO ;bitpos:[19:0] ;default: 20'b0 ; */
/*description: software can read this register to get the current counter value
in low speed timer3.*/
#define LEDC_LSTIMER3_CNT 0x000FFFFF
#define LEDC_LSTIMER3_CNT_M ((LEDC_LSTIMER3_CNT_V)<<(LEDC_LSTIMER3_CNT_S))
#define LEDC_LSTIMER3_CNT_V 0xFFFFF
#define LEDC_LSTIMER3_CNT_S 0
#define LEDC_INT_RAW_REG (DR_REG_LEDC_BASE + 0x0180)
/* LEDC_DUTY_CHNG_END_LSCH7_INT_RAW : RO ;bitpos:[23] ;default: 1'b0 ; */
/*description: The interrupt raw bit for low speed channel 7 duty change done.*/
#define LEDC_DUTY_CHNG_END_LSCH7_INT_RAW (BIT(23))
#define LEDC_DUTY_CHNG_END_LSCH7_INT_RAW_M (BIT(23))
#define LEDC_DUTY_CHNG_END_LSCH7_INT_RAW_V 0x1
#define LEDC_DUTY_CHNG_END_LSCH7_INT_RAW_S 23
/* LEDC_DUTY_CHNG_END_LSCH6_INT_RAW : RO ;bitpos:[22] ;default: 1'b0 ; */
/*description: The interrupt raw bit for low speed channel 6 duty change done.*/
#define LEDC_DUTY_CHNG_END_LSCH6_INT_RAW (BIT(22))
#define LEDC_DUTY_CHNG_END_LSCH6_INT_RAW_M (BIT(22))
#define LEDC_DUTY_CHNG_END_LSCH6_INT_RAW_V 0x1
#define LEDC_DUTY_CHNG_END_LSCH6_INT_RAW_S 22
/* LEDC_DUTY_CHNG_END_LSCH5_INT_RAW : RO ;bitpos:[21] ;default: 1'b0 ; */
/*description: The interrupt raw bit for low speed channel 5 duty change done.*/
#define LEDC_DUTY_CHNG_END_LSCH5_INT_RAW (BIT(21))
#define LEDC_DUTY_CHNG_END_LSCH5_INT_RAW_M (BIT(21))
#define LEDC_DUTY_CHNG_END_LSCH5_INT_RAW_V 0x1
#define LEDC_DUTY_CHNG_END_LSCH5_INT_RAW_S 21
/* LEDC_DUTY_CHNG_END_LSCH4_INT_RAW : RO ;bitpos:[20] ;default: 1'b0 ; */
/*description: The interrupt raw bit for low speed channel 4 duty change done.*/
#define LEDC_DUTY_CHNG_END_LSCH4_INT_RAW (BIT(20))
#define LEDC_DUTY_CHNG_END_LSCH4_INT_RAW_M (BIT(20))
#define LEDC_DUTY_CHNG_END_LSCH4_INT_RAW_V 0x1
#define LEDC_DUTY_CHNG_END_LSCH4_INT_RAW_S 20
/* LEDC_DUTY_CHNG_END_LSCH3_INT_RAW : RO ;bitpos:[19] ;default: 1'b0 ; */
/*description: The interrupt raw bit for low speed channel 3 duty change done.*/
#define LEDC_DUTY_CHNG_END_LSCH3_INT_RAW (BIT(19))
#define LEDC_DUTY_CHNG_END_LSCH3_INT_RAW_M (BIT(19))
#define LEDC_DUTY_CHNG_END_LSCH3_INT_RAW_V 0x1
#define LEDC_DUTY_CHNG_END_LSCH3_INT_RAW_S 19
/* LEDC_DUTY_CHNG_END_LSCH2_INT_RAW : RO ;bitpos:[18] ;default: 1'b0 ; */
/*description: The interrupt raw bit for low speed channel 2 duty change done.*/
#define LEDC_DUTY_CHNG_END_LSCH2_INT_RAW (BIT(18))
#define LEDC_DUTY_CHNG_END_LSCH2_INT_RAW_M (BIT(18))
#define LEDC_DUTY_CHNG_END_LSCH2_INT_RAW_V 0x1
#define LEDC_DUTY_CHNG_END_LSCH2_INT_RAW_S 18
/* LEDC_DUTY_CHNG_END_LSCH1_INT_RAW : RO ;bitpos:[17] ;default: 1'b0 ; */
/*description: The interrupt raw bit for low speed channel 1 duty change done.*/
#define LEDC_DUTY_CHNG_END_LSCH1_INT_RAW (BIT(17))
#define LEDC_DUTY_CHNG_END_LSCH1_INT_RAW_M (BIT(17))
#define LEDC_DUTY_CHNG_END_LSCH1_INT_RAW_V 0x1
#define LEDC_DUTY_CHNG_END_LSCH1_INT_RAW_S 17
/* LEDC_DUTY_CHNG_END_LSCH0_INT_RAW : RO ;bitpos:[16] ;default: 1'b0 ; */
/*description: The interrupt raw bit for low speed channel 0 duty change done.*/
#define LEDC_DUTY_CHNG_END_LSCH0_INT_RAW (BIT(16))
#define LEDC_DUTY_CHNG_END_LSCH0_INT_RAW_M (BIT(16))
#define LEDC_DUTY_CHNG_END_LSCH0_INT_RAW_V 0x1
#define LEDC_DUTY_CHNG_END_LSCH0_INT_RAW_S 16
/* LEDC_DUTY_CHNG_END_HSCH7_INT_RAW : RO ;bitpos:[15] ;default: 1'b0 ; */
/*description: The interrupt raw bit for high speed channel 7 duty change done.*/
#define LEDC_DUTY_CHNG_END_HSCH7_INT_RAW (BIT(15))
#define LEDC_DUTY_CHNG_END_HSCH7_INT_RAW_M (BIT(15))
#define LEDC_DUTY_CHNG_END_HSCH7_INT_RAW_V 0x1
#define LEDC_DUTY_CHNG_END_HSCH7_INT_RAW_S 15
/* LEDC_DUTY_CHNG_END_HSCH6_INT_RAW : RO ;bitpos:[14] ;default: 1'b0 ; */
/*description: The interrupt raw bit for high speed channel 6 duty change done.*/
#define LEDC_DUTY_CHNG_END_HSCH6_INT_RAW (BIT(14))
#define LEDC_DUTY_CHNG_END_HSCH6_INT_RAW_M (BIT(14))
#define LEDC_DUTY_CHNG_END_HSCH6_INT_RAW_V 0x1
#define LEDC_DUTY_CHNG_END_HSCH6_INT_RAW_S 14
/* LEDC_DUTY_CHNG_END_HSCH5_INT_RAW : RO ;bitpos:[13] ;default: 1'b0 ; */
/*description: The interrupt raw bit for high speed channel 5 duty change done.*/
#define LEDC_DUTY_CHNG_END_HSCH5_INT_RAW (BIT(13))
#define LEDC_DUTY_CHNG_END_HSCH5_INT_RAW_M (BIT(13))
#define LEDC_DUTY_CHNG_END_HSCH5_INT_RAW_V 0x1
#define LEDC_DUTY_CHNG_END_HSCH5_INT_RAW_S 13
/* LEDC_DUTY_CHNG_END_HSCH4_INT_RAW : RO ;bitpos:[12] ;default: 1'b0 ; */
/*description: The interrupt raw bit for high speed channel 4 duty change done.*/
#define LEDC_DUTY_CHNG_END_HSCH4_INT_RAW (BIT(12))
#define LEDC_DUTY_CHNG_END_HSCH4_INT_RAW_M (BIT(12))
#define LEDC_DUTY_CHNG_END_HSCH4_INT_RAW_V 0x1
#define LEDC_DUTY_CHNG_END_HSCH4_INT_RAW_S 12
/* LEDC_DUTY_CHNG_END_HSCH3_INT_RAW : RO ;bitpos:[11] ;default: 1'b0 ; */
/*description: The interrupt raw bit for high speed channel 3 duty change done.*/
#define LEDC_DUTY_CHNG_END_HSCH3_INT_RAW (BIT(11))
#define LEDC_DUTY_CHNG_END_HSCH3_INT_RAW_M (BIT(11))
#define LEDC_DUTY_CHNG_END_HSCH3_INT_RAW_V 0x1
#define LEDC_DUTY_CHNG_END_HSCH3_INT_RAW_S 11
/* LEDC_DUTY_CHNG_END_HSCH2_INT_RAW : RO ;bitpos:[10] ;default: 1'b0 ; */
/*description: The interrupt raw bit for high speed channel 2 duty change done.*/
#define LEDC_DUTY_CHNG_END_HSCH2_INT_RAW (BIT(10))
#define LEDC_DUTY_CHNG_END_HSCH2_INT_RAW_M (BIT(10))
#define LEDC_DUTY_CHNG_END_HSCH2_INT_RAW_V 0x1
#define LEDC_DUTY_CHNG_END_HSCH2_INT_RAW_S 10
/* LEDC_DUTY_CHNG_END_HSCH1_INT_RAW : RO ;bitpos:[9] ;default: 1'b0 ; */
/*description: The interrupt raw bit for high speed channel 1 duty change done.*/
#define LEDC_DUTY_CHNG_END_HSCH1_INT_RAW (BIT(9))
#define LEDC_DUTY_CHNG_END_HSCH1_INT_RAW_M (BIT(9))
#define LEDC_DUTY_CHNG_END_HSCH1_INT_RAW_V 0x1
#define LEDC_DUTY_CHNG_END_HSCH1_INT_RAW_S 9
/* LEDC_DUTY_CHNG_END_HSCH0_INT_RAW : RO ;bitpos:[8] ;default: 1'b0 ; */
/*description: The interrupt raw bit for high speed channel 0 duty change done.*/
#define LEDC_DUTY_CHNG_END_HSCH0_INT_RAW (BIT(8))
#define LEDC_DUTY_CHNG_END_HSCH0_INT_RAW_M (BIT(8))
#define LEDC_DUTY_CHNG_END_HSCH0_INT_RAW_V 0x1
#define LEDC_DUTY_CHNG_END_HSCH0_INT_RAW_S 8
/* LEDC_LSTIMER3_OVF_INT_RAW : RO ;bitpos:[7] ;default: 1'b0 ; */
/*description: The interrupt raw bit for low speed channel3 counter overflow.*/
#define LEDC_LSTIMER3_OVF_INT_RAW (BIT(7))
#define LEDC_LSTIMER3_OVF_INT_RAW_M (BIT(7))
#define LEDC_LSTIMER3_OVF_INT_RAW_V 0x1
#define LEDC_LSTIMER3_OVF_INT_RAW_S 7
/* LEDC_LSTIMER2_OVF_INT_RAW : RO ;bitpos:[6] ;default: 1'b0 ; */
/*description: The interrupt raw bit for low speed channel2 counter overflow.*/
#define LEDC_LSTIMER2_OVF_INT_RAW (BIT(6))
#define LEDC_LSTIMER2_OVF_INT_RAW_M (BIT(6))
#define LEDC_LSTIMER2_OVF_INT_RAW_V 0x1
#define LEDC_LSTIMER2_OVF_INT_RAW_S 6
/* LEDC_LSTIMER1_OVF_INT_RAW : RO ;bitpos:[5] ;default: 1'b0 ; */
/*description: The interrupt raw bit for low speed channel1 counter overflow.*/
#define LEDC_LSTIMER1_OVF_INT_RAW (BIT(5))
#define LEDC_LSTIMER1_OVF_INT_RAW_M (BIT(5))
#define LEDC_LSTIMER1_OVF_INT_RAW_V 0x1
#define LEDC_LSTIMER1_OVF_INT_RAW_S 5
/* LEDC_LSTIMER0_OVF_INT_RAW : RO ;bitpos:[4] ;default: 1'b0 ; */
/*description: The interrupt raw bit for low speed channel0 counter overflow.*/
#define LEDC_LSTIMER0_OVF_INT_RAW (BIT(4))
#define LEDC_LSTIMER0_OVF_INT_RAW_M (BIT(4))
#define LEDC_LSTIMER0_OVF_INT_RAW_V 0x1
#define LEDC_LSTIMER0_OVF_INT_RAW_S 4
/* LEDC_HSTIMER3_OVF_INT_RAW : RO ;bitpos:[3] ;default: 1'b0 ; */
/*description: The interrupt raw bit for high speed channel3 counter overflow.*/
#define LEDC_HSTIMER3_OVF_INT_RAW (BIT(3))
#define LEDC_HSTIMER3_OVF_INT_RAW_M (BIT(3))
#define LEDC_HSTIMER3_OVF_INT_RAW_V 0x1
#define LEDC_HSTIMER3_OVF_INT_RAW_S 3
/* LEDC_HSTIMER2_OVF_INT_RAW : RO ;bitpos:[2] ;default: 1'b0 ; */
/*description: The interrupt raw bit for high speed channel2 counter overflow.*/
#define LEDC_HSTIMER2_OVF_INT_RAW (BIT(2))
#define LEDC_HSTIMER2_OVF_INT_RAW_M (BIT(2))
#define LEDC_HSTIMER2_OVF_INT_RAW_V 0x1
#define LEDC_HSTIMER2_OVF_INT_RAW_S 2
/* LEDC_HSTIMER1_OVF_INT_RAW : RO ;bitpos:[1] ;default: 1'b0 ; */
/*description: The interrupt raw bit for high speed channel1 counter overflow.*/
#define LEDC_HSTIMER1_OVF_INT_RAW (BIT(1))
#define LEDC_HSTIMER1_OVF_INT_RAW_M (BIT(1))
#define LEDC_HSTIMER1_OVF_INT_RAW_V 0x1
#define LEDC_HSTIMER1_OVF_INT_RAW_S 1
/* LEDC_HSTIMER0_OVF_INT_RAW : RO ;bitpos:[0] ;default: 1'b0 ; */
/*description: The interrupt raw bit for high speed channel0 counter overflow.*/
#define LEDC_HSTIMER0_OVF_INT_RAW (BIT(0))
#define LEDC_HSTIMER0_OVF_INT_RAW_M (BIT(0))
#define LEDC_HSTIMER0_OVF_INT_RAW_V 0x1
#define LEDC_HSTIMER0_OVF_INT_RAW_S 0
#define LEDC_INT_ST_REG (DR_REG_LEDC_BASE + 0x0184)
/* LEDC_DUTY_CHNG_END_LSCH7_INT_ST : RO ;bitpos:[23] ;default: 1'h0 ; */
/*description: The interrupt status bit for low speed channel 7 duty change done event*/
#define LEDC_DUTY_CHNG_END_LSCH7_INT_ST (BIT(23))
#define LEDC_DUTY_CHNG_END_LSCH7_INT_ST_M (BIT(23))
#define LEDC_DUTY_CHNG_END_LSCH7_INT_ST_V 0x1
#define LEDC_DUTY_CHNG_END_LSCH7_INT_ST_S 23
/* LEDC_DUTY_CHNG_END_LSCH6_INT_ST : RO ;bitpos:[22] ;default: 1'b0 ; */
/*description: The interrupt status bit for low speed channel 6 duty change done event.*/
#define LEDC_DUTY_CHNG_END_LSCH6_INT_ST (BIT(22))
#define LEDC_DUTY_CHNG_END_LSCH6_INT_ST_M (BIT(22))
#define LEDC_DUTY_CHNG_END_LSCH6_INT_ST_V 0x1
#define LEDC_DUTY_CHNG_END_LSCH6_INT_ST_S 22
/* LEDC_DUTY_CHNG_END_LSCH5_INT_ST : RO ;bitpos:[21] ;default: 1'b0 ; */
/*description: The interrupt status bit for low speed channel 5 duty change done event.*/
#define LEDC_DUTY_CHNG_END_LSCH5_INT_ST (BIT(21))
#define LEDC_DUTY_CHNG_END_LSCH5_INT_ST_M (BIT(21))
#define LEDC_DUTY_CHNG_END_LSCH5_INT_ST_V 0x1
#define LEDC_DUTY_CHNG_END_LSCH5_INT_ST_S 21
/* LEDC_DUTY_CHNG_END_LSCH4_INT_ST : RO ;bitpos:[20] ;default: 1'b0 ; */
/*description: The interrupt status bit for low speed channel 4 duty change done event.*/
#define LEDC_DUTY_CHNG_END_LSCH4_INT_ST (BIT(20))
#define LEDC_DUTY_CHNG_END_LSCH4_INT_ST_M (BIT(20))
#define LEDC_DUTY_CHNG_END_LSCH4_INT_ST_V 0x1
#define LEDC_DUTY_CHNG_END_LSCH4_INT_ST_S 20
/* LEDC_DUTY_CHNG_END_LSCH3_INT_ST : RO ;bitpos:[19] ;default: 1'b0 ; */
/*description: The interrupt status bit for low speed channel 3 duty change done event.*/
#define LEDC_DUTY_CHNG_END_LSCH3_INT_ST (BIT(19))
#define LEDC_DUTY_CHNG_END_LSCH3_INT_ST_M (BIT(19))
#define LEDC_DUTY_CHNG_END_LSCH3_INT_ST_V 0x1
#define LEDC_DUTY_CHNG_END_LSCH3_INT_ST_S 19
/* LEDC_DUTY_CHNG_END_LSCH2_INT_ST : RO ;bitpos:[18] ;default: 1'b0 ; */
/*description: The interrupt status bit for low speed channel 2 duty change done event.*/
#define LEDC_DUTY_CHNG_END_LSCH2_INT_ST (BIT(18))
#define LEDC_DUTY_CHNG_END_LSCH2_INT_ST_M (BIT(18))
#define LEDC_DUTY_CHNG_END_LSCH2_INT_ST_V 0x1
#define LEDC_DUTY_CHNG_END_LSCH2_INT_ST_S 18
/* LEDC_DUTY_CHNG_END_LSCH1_INT_ST : RO ;bitpos:[17] ;default: 1'b0 ; */
/*description: The interrupt status bit for low speed channel 1 duty change done event.*/
#define LEDC_DUTY_CHNG_END_LSCH1_INT_ST (BIT(17))
#define LEDC_DUTY_CHNG_END_LSCH1_INT_ST_M (BIT(17))
#define LEDC_DUTY_CHNG_END_LSCH1_INT_ST_V 0x1
#define LEDC_DUTY_CHNG_END_LSCH1_INT_ST_S 17
/* LEDC_DUTY_CHNG_END_LSCH0_INT_ST : RO ;bitpos:[16] ;default: 1'b0 ; */
/*description: The interrupt status bit for low speed channel 0 duty change done event.*/
#define LEDC_DUTY_CHNG_END_LSCH0_INT_ST (BIT(16))
#define LEDC_DUTY_CHNG_END_LSCH0_INT_ST_M (BIT(16))
#define LEDC_DUTY_CHNG_END_LSCH0_INT_ST_V 0x1
#define LEDC_DUTY_CHNG_END_LSCH0_INT_ST_S 16
/* LEDC_DUTY_CHNG_END_HSCH7_INT_ST : RO ;bitpos:[15] ;default: 1'b0 ; */
/*description: The interrupt status bit for high speed channel 7 duty change done event.*/
#define LEDC_DUTY_CHNG_END_HSCH7_INT_ST (BIT(15))
#define LEDC_DUTY_CHNG_END_HSCH7_INT_ST_M (BIT(15))
#define LEDC_DUTY_CHNG_END_HSCH7_INT_ST_V 0x1
#define LEDC_DUTY_CHNG_END_HSCH7_INT_ST_S 15
/* LEDC_DUTY_CHNG_END_HSCH6_INT_ST : RO ;bitpos:[14] ;default: 1'b0 ; */
/*description: The interrupt status bit for high speed channel 6 duty change done event.*/
#define LEDC_DUTY_CHNG_END_HSCH6_INT_ST (BIT(14))
#define LEDC_DUTY_CHNG_END_HSCH6_INT_ST_M (BIT(14))
#define LEDC_DUTY_CHNG_END_HSCH6_INT_ST_V 0x1
#define LEDC_DUTY_CHNG_END_HSCH6_INT_ST_S 14
/* LEDC_DUTY_CHNG_END_HSCH5_INT_ST : RO ;bitpos:[13] ;default: 1'b0 ; */
/*description: The interrupt status bit for high speed channel 5 duty change done event.*/
#define LEDC_DUTY_CHNG_END_HSCH5_INT_ST (BIT(13))
#define LEDC_DUTY_CHNG_END_HSCH5_INT_ST_M (BIT(13))
#define LEDC_DUTY_CHNG_END_HSCH5_INT_ST_V 0x1
#define LEDC_DUTY_CHNG_END_HSCH5_INT_ST_S 13
/* LEDC_DUTY_CHNG_END_HSCH4_INT_ST : RO ;bitpos:[12] ;default: 1'b0 ; */
/*description: The interrupt status bit for high speed channel 4 duty change done event.*/
#define LEDC_DUTY_CHNG_END_HSCH4_INT_ST (BIT(12))
#define LEDC_DUTY_CHNG_END_HSCH4_INT_ST_M (BIT(12))
#define LEDC_DUTY_CHNG_END_HSCH4_INT_ST_V 0x1
#define LEDC_DUTY_CHNG_END_HSCH4_INT_ST_S 12
/* LEDC_DUTY_CHNG_END_HSCH3_INT_ST : RO ;bitpos:[11] ;default: 1'b0 ; */
/*description: The interrupt status bit for high speed channel 3 duty change done event.*/
#define LEDC_DUTY_CHNG_END_HSCH3_INT_ST (BIT(11))
#define LEDC_DUTY_CHNG_END_HSCH3_INT_ST_M (BIT(11))
#define LEDC_DUTY_CHNG_END_HSCH3_INT_ST_V 0x1
#define LEDC_DUTY_CHNG_END_HSCH3_INT_ST_S 11
/* LEDC_DUTY_CHNG_END_HSCH2_INT_ST : RO ;bitpos:[10] ;default: 1'b0 ; */
/*description: The interrupt status bit for high speed channel 2 duty change done event.*/
#define LEDC_DUTY_CHNG_END_HSCH2_INT_ST (BIT(10))
#define LEDC_DUTY_CHNG_END_HSCH2_INT_ST_M (BIT(10))
#define LEDC_DUTY_CHNG_END_HSCH2_INT_ST_V 0x1
#define LEDC_DUTY_CHNG_END_HSCH2_INT_ST_S 10
/* LEDC_DUTY_CHNG_END_HSCH1_INT_ST : RO ;bitpos:[9] ;default: 1'b0 ; */
/*description: The interrupt status bit for high speed channel 1 duty change done event.*/
#define LEDC_DUTY_CHNG_END_HSCH1_INT_ST (BIT(9))
#define LEDC_DUTY_CHNG_END_HSCH1_INT_ST_M (BIT(9))
#define LEDC_DUTY_CHNG_END_HSCH1_INT_ST_V 0x1
#define LEDC_DUTY_CHNG_END_HSCH1_INT_ST_S 9
/* LEDC_DUTY_CHNG_END_HSCH0_INT_ST : RO ;bitpos:[8] ;default: 1'b0 ; */
/*description: The interrupt status bit for high speed channel 0 duty change done event.*/
#define LEDC_DUTY_CHNG_END_HSCH0_INT_ST (BIT(8))
#define LEDC_DUTY_CHNG_END_HSCH0_INT_ST_M (BIT(8))
#define LEDC_DUTY_CHNG_END_HSCH0_INT_ST_V 0x1
#define LEDC_DUTY_CHNG_END_HSCH0_INT_ST_S 8
/* LEDC_LSTIMER3_OVF_INT_ST : RO ;bitpos:[7] ;default: 1'b0 ; */
/*description: The interrupt status bit for low speed channel3 counter overflow event.*/
#define LEDC_LSTIMER3_OVF_INT_ST (BIT(7))
#define LEDC_LSTIMER3_OVF_INT_ST_M (BIT(7))
#define LEDC_LSTIMER3_OVF_INT_ST_V 0x1
#define LEDC_LSTIMER3_OVF_INT_ST_S 7
/* LEDC_LSTIMER2_OVF_INT_ST : RO ;bitpos:[6] ;default: 1'b0 ; */
/*description: The interrupt status bit for low speed channel2 counter overflow event.*/
#define LEDC_LSTIMER2_OVF_INT_ST (BIT(6))
#define LEDC_LSTIMER2_OVF_INT_ST_M (BIT(6))
#define LEDC_LSTIMER2_OVF_INT_ST_V 0x1
#define LEDC_LSTIMER2_OVF_INT_ST_S 6
/* LEDC_LSTIMER1_OVF_INT_ST : RO ;bitpos:[5] ;default: 1'b0 ; */
/*description: The interrupt status bit for low speed channel1 counter overflow event.*/
#define LEDC_LSTIMER1_OVF_INT_ST (BIT(5))
#define LEDC_LSTIMER1_OVF_INT_ST_M (BIT(5))
#define LEDC_LSTIMER1_OVF_INT_ST_V 0x1
#define LEDC_LSTIMER1_OVF_INT_ST_S 5
/* LEDC_LSTIMER0_OVF_INT_ST : RO ;bitpos:[4] ;default: 1'b0 ; */
/*description: The interrupt status bit for low speed channel0 counter overflow event.*/
#define LEDC_LSTIMER0_OVF_INT_ST (BIT(4))
#define LEDC_LSTIMER0_OVF_INT_ST_M (BIT(4))
#define LEDC_LSTIMER0_OVF_INT_ST_V 0x1
#define LEDC_LSTIMER0_OVF_INT_ST_S 4
/* LEDC_HSTIMER3_OVF_INT_ST : RO ;bitpos:[3] ;default: 1'b0 ; */
/*description: The interrupt status bit for high speed channel3 counter overflow event.*/
#define LEDC_HSTIMER3_OVF_INT_ST (BIT(3))
#define LEDC_HSTIMER3_OVF_INT_ST_M (BIT(3))
#define LEDC_HSTIMER3_OVF_INT_ST_V 0x1
#define LEDC_HSTIMER3_OVF_INT_ST_S 3
/* LEDC_HSTIMER2_OVF_INT_ST : RO ;bitpos:[2] ;default: 1'b0 ; */
/*description: The interrupt status bit for high speed channel2 counter overflow event.*/
#define LEDC_HSTIMER2_OVF_INT_ST (BIT(2))
#define LEDC_HSTIMER2_OVF_INT_ST_M (BIT(2))
#define LEDC_HSTIMER2_OVF_INT_ST_V 0x1
#define LEDC_HSTIMER2_OVF_INT_ST_S 2
/* LEDC_HSTIMER1_OVF_INT_ST : RO ;bitpos:[1] ;default: 1'b0 ; */
/*description: The interrupt status bit for high speed channel1 counter overflow event.*/
#define LEDC_HSTIMER1_OVF_INT_ST (BIT(1))
#define LEDC_HSTIMER1_OVF_INT_ST_M (BIT(1))
#define LEDC_HSTIMER1_OVF_INT_ST_V 0x1
#define LEDC_HSTIMER1_OVF_INT_ST_S 1
/* LEDC_HSTIMER0_OVF_INT_ST : RO ;bitpos:[0] ;default: 1'b0 ; */
/*description: The interrupt status bit for high speed channel0 counter overflow event.*/
#define LEDC_HSTIMER0_OVF_INT_ST (BIT(0))
#define LEDC_HSTIMER0_OVF_INT_ST_M (BIT(0))
#define LEDC_HSTIMER0_OVF_INT_ST_V 0x1
#define LEDC_HSTIMER0_OVF_INT_ST_S 0
#define LEDC_INT_ENA_REG (DR_REG_LEDC_BASE + 0x0188)
/* LEDC_DUTY_CHNG_END_LSCH7_INT_ENA : R/W ;bitpos:[23] ;default: 1'h0 ; */
/*description: The interrupt enable bit for low speed channel 7 duty change done interrupt.*/
#define LEDC_DUTY_CHNG_END_LSCH7_INT_ENA (BIT(23))
#define LEDC_DUTY_CHNG_END_LSCH7_INT_ENA_M (BIT(23))
#define LEDC_DUTY_CHNG_END_LSCH7_INT_ENA_V 0x1
#define LEDC_DUTY_CHNG_END_LSCH7_INT_ENA_S 23
/* LEDC_DUTY_CHNG_END_LSCH6_INT_ENA : R/W ;bitpos:[22] ;default: 1'b0 ; */
/*description: The interrupt enable bit for low speed channel 6 duty change done interrupt.*/
#define LEDC_DUTY_CHNG_END_LSCH6_INT_ENA (BIT(22))
#define LEDC_DUTY_CHNG_END_LSCH6_INT_ENA_M (BIT(22))
#define LEDC_DUTY_CHNG_END_LSCH6_INT_ENA_V 0x1
#define LEDC_DUTY_CHNG_END_LSCH6_INT_ENA_S 22
/* LEDC_DUTY_CHNG_END_LSCH5_INT_ENA : R/W ;bitpos:[21] ;default: 1'b0 ; */
/*description: The interrupt enable bit for low speed channel 5 duty change done interrupt.*/
#define LEDC_DUTY_CHNG_END_LSCH5_INT_ENA (BIT(21))
#define LEDC_DUTY_CHNG_END_LSCH5_INT_ENA_M (BIT(21))
#define LEDC_DUTY_CHNG_END_LSCH5_INT_ENA_V 0x1
#define LEDC_DUTY_CHNG_END_LSCH5_INT_ENA_S 21
/* LEDC_DUTY_CHNG_END_LSCH4_INT_ENA : R/W ;bitpos:[20] ;default: 1'b0 ; */
/*description: The interrupt enable bit for low speed channel 4 duty change done interrupt.*/
#define LEDC_DUTY_CHNG_END_LSCH4_INT_ENA (BIT(20))
#define LEDC_DUTY_CHNG_END_LSCH4_INT_ENA_M (BIT(20))
#define LEDC_DUTY_CHNG_END_LSCH4_INT_ENA_V 0x1
#define LEDC_DUTY_CHNG_END_LSCH4_INT_ENA_S 20
/* LEDC_DUTY_CHNG_END_LSCH3_INT_ENA : R/W ;bitpos:[19] ;default: 1'b0 ; */
/*description: The interrupt enable bit for low speed channel 3 duty change done interrupt.*/
#define LEDC_DUTY_CHNG_END_LSCH3_INT_ENA (BIT(19))
#define LEDC_DUTY_CHNG_END_LSCH3_INT_ENA_M (BIT(19))
#define LEDC_DUTY_CHNG_END_LSCH3_INT_ENA_V 0x1
#define LEDC_DUTY_CHNG_END_LSCH3_INT_ENA_S 19
/* LEDC_DUTY_CHNG_END_LSCH2_INT_ENA : R/W ;bitpos:[18] ;default: 1'b0 ; */
/*description: The interrupt enable bit for low speed channel 2 duty change done interrupt.*/
#define LEDC_DUTY_CHNG_END_LSCH2_INT_ENA (BIT(18))
#define LEDC_DUTY_CHNG_END_LSCH2_INT_ENA_M (BIT(18))
#define LEDC_DUTY_CHNG_END_LSCH2_INT_ENA_V 0x1
#define LEDC_DUTY_CHNG_END_LSCH2_INT_ENA_S 18
/* LEDC_DUTY_CHNG_END_LSCH1_INT_ENA : R/W ;bitpos:[17] ;default: 1'b0 ; */
/*description: The interrupt enable bit for low speed channel 1 duty change done interrupt.*/
#define LEDC_DUTY_CHNG_END_LSCH1_INT_ENA (BIT(17))
#define LEDC_DUTY_CHNG_END_LSCH1_INT_ENA_M (BIT(17))
#define LEDC_DUTY_CHNG_END_LSCH1_INT_ENA_V 0x1
#define LEDC_DUTY_CHNG_END_LSCH1_INT_ENA_S 17
/* LEDC_DUTY_CHNG_END_LSCH0_INT_ENA : R/W ;bitpos:[16] ;default: 1'b0 ; */
/*description: The interrupt enable bit for low speed channel 0 duty change done interrupt.*/
#define LEDC_DUTY_CHNG_END_LSCH0_INT_ENA (BIT(16))
#define LEDC_DUTY_CHNG_END_LSCH0_INT_ENA_M (BIT(16))
#define LEDC_DUTY_CHNG_END_LSCH0_INT_ENA_V 0x1
#define LEDC_DUTY_CHNG_END_LSCH0_INT_ENA_S 16
/* LEDC_DUTY_CHNG_END_HSCH7_INT_ENA : R/W ;bitpos:[15] ;default: 1'b0 ; */
/*description: The interrupt enable bit for high speed channel 7 duty change done interrupt.*/
#define LEDC_DUTY_CHNG_END_HSCH7_INT_ENA (BIT(15))
#define LEDC_DUTY_CHNG_END_HSCH7_INT_ENA_M (BIT(15))
#define LEDC_DUTY_CHNG_END_HSCH7_INT_ENA_V 0x1
#define LEDC_DUTY_CHNG_END_HSCH7_INT_ENA_S 15
/* LEDC_DUTY_CHNG_END_HSCH6_INT_ENA : R/W ;bitpos:[14] ;default: 1'b0 ; */
/*description: The interrupt enable bit for high speed channel 6 duty change done interrupt.*/
#define LEDC_DUTY_CHNG_END_HSCH6_INT_ENA (BIT(14))
#define LEDC_DUTY_CHNG_END_HSCH6_INT_ENA_M (BIT(14))
#define LEDC_DUTY_CHNG_END_HSCH6_INT_ENA_V 0x1
#define LEDC_DUTY_CHNG_END_HSCH6_INT_ENA_S 14
/* LEDC_DUTY_CHNG_END_HSCH5_INT_ENA : R/W ;bitpos:[13] ;default: 1'b0 ; */
/*description: The interrupt enable bit for high speed channel 5 duty change done interrupt.*/
#define LEDC_DUTY_CHNG_END_HSCH5_INT_ENA (BIT(13))
#define LEDC_DUTY_CHNG_END_HSCH5_INT_ENA_M (BIT(13))
#define LEDC_DUTY_CHNG_END_HSCH5_INT_ENA_V 0x1
#define LEDC_DUTY_CHNG_END_HSCH5_INT_ENA_S 13
/* LEDC_DUTY_CHNG_END_HSCH4_INT_ENA : R/W ;bitpos:[12] ;default: 1'b0 ; */
/*description: The interrupt enable bit for high speed channel 4 duty change done interrupt.*/
#define LEDC_DUTY_CHNG_END_HSCH4_INT_ENA (BIT(12))
#define LEDC_DUTY_CHNG_END_HSCH4_INT_ENA_M (BIT(12))
#define LEDC_DUTY_CHNG_END_HSCH4_INT_ENA_V 0x1
#define LEDC_DUTY_CHNG_END_HSCH4_INT_ENA_S 12
/* LEDC_DUTY_CHNG_END_HSCH3_INT_ENA : R/W ;bitpos:[11] ;default: 1'b0 ; */
/*description: The interrupt enable bit for high speed channel 3 duty change done interrupt.*/
#define LEDC_DUTY_CHNG_END_HSCH3_INT_ENA (BIT(11))
#define LEDC_DUTY_CHNG_END_HSCH3_INT_ENA_M (BIT(11))
#define LEDC_DUTY_CHNG_END_HSCH3_INT_ENA_V 0x1
#define LEDC_DUTY_CHNG_END_HSCH3_INT_ENA_S 11
/* LEDC_DUTY_CHNG_END_HSCH2_INT_ENA : R/W ;bitpos:[10] ;default: 1'b0 ; */
/*description: The interrupt enable bit for high speed channel 2 duty change done interrupt.*/
#define LEDC_DUTY_CHNG_END_HSCH2_INT_ENA (BIT(10))
#define LEDC_DUTY_CHNG_END_HSCH2_INT_ENA_M (BIT(10))
#define LEDC_DUTY_CHNG_END_HSCH2_INT_ENA_V 0x1
#define LEDC_DUTY_CHNG_END_HSCH2_INT_ENA_S 10
/* LEDC_DUTY_CHNG_END_HSCH1_INT_ENA : R/W ;bitpos:[9] ;default: 1'b0 ; */
/*description: The interrupt enable bit for high speed channel 1 duty change done interrupt.*/
#define LEDC_DUTY_CHNG_END_HSCH1_INT_ENA (BIT(9))
#define LEDC_DUTY_CHNG_END_HSCH1_INT_ENA_M (BIT(9))
#define LEDC_DUTY_CHNG_END_HSCH1_INT_ENA_V 0x1
#define LEDC_DUTY_CHNG_END_HSCH1_INT_ENA_S 9
/* LEDC_DUTY_CHNG_END_HSCH0_INT_ENA : R/W ;bitpos:[8] ;default: 1'b0 ; */
/*description: The interrupt enable bit for high speed channel 0 duty change done interrupt.*/
#define LEDC_DUTY_CHNG_END_HSCH0_INT_ENA (BIT(8))
#define LEDC_DUTY_CHNG_END_HSCH0_INT_ENA_M (BIT(8))
#define LEDC_DUTY_CHNG_END_HSCH0_INT_ENA_V 0x1
#define LEDC_DUTY_CHNG_END_HSCH0_INT_ENA_S 8
/* LEDC_LSTIMER3_OVF_INT_ENA : R/W ;bitpos:[7] ;default: 1'b0 ; */
/*description: The interrupt enable bit for low speed channel3 counter overflow interrupt.*/
#define LEDC_LSTIMER3_OVF_INT_ENA (BIT(7))
#define LEDC_LSTIMER3_OVF_INT_ENA_M (BIT(7))
#define LEDC_LSTIMER3_OVF_INT_ENA_V 0x1
#define LEDC_LSTIMER3_OVF_INT_ENA_S 7
/* LEDC_LSTIMER2_OVF_INT_ENA : R/W ;bitpos:[6] ;default: 1'b0 ; */
/*description: The interrupt enable bit for low speed channel2 counter overflow interrupt.*/
#define LEDC_LSTIMER2_OVF_INT_ENA (BIT(6))
#define LEDC_LSTIMER2_OVF_INT_ENA_M (BIT(6))
#define LEDC_LSTIMER2_OVF_INT_ENA_V 0x1
#define LEDC_LSTIMER2_OVF_INT_ENA_S 6
/* LEDC_LSTIMER1_OVF_INT_ENA : R/W ;bitpos:[5] ;default: 1'b0 ; */
/*description: The interrupt enable bit for low speed channel1 counter overflow interrupt.*/
#define LEDC_LSTIMER1_OVF_INT_ENA (BIT(5))
#define LEDC_LSTIMER1_OVF_INT_ENA_M (BIT(5))
#define LEDC_LSTIMER1_OVF_INT_ENA_V 0x1
#define LEDC_LSTIMER1_OVF_INT_ENA_S 5
/* LEDC_LSTIMER0_OVF_INT_ENA : R/W ;bitpos:[4] ;default: 1'b0 ; */
/*description: The interrupt enable bit for low speed channel0 counter overflow interrupt.*/
#define LEDC_LSTIMER0_OVF_INT_ENA (BIT(4))
#define LEDC_LSTIMER0_OVF_INT_ENA_M (BIT(4))
#define LEDC_LSTIMER0_OVF_INT_ENA_V 0x1
#define LEDC_LSTIMER0_OVF_INT_ENA_S 4
/* LEDC_HSTIMER3_OVF_INT_ENA : R/W ;bitpos:[3] ;default: 1'b0 ; */
/*description: The interrupt enable bit for high speed channel3 counter overflow interrupt.*/
#define LEDC_HSTIMER3_OVF_INT_ENA (BIT(3))
#define LEDC_HSTIMER3_OVF_INT_ENA_M (BIT(3))
#define LEDC_HSTIMER3_OVF_INT_ENA_V 0x1
#define LEDC_HSTIMER3_OVF_INT_ENA_S 3
/* LEDC_HSTIMER2_OVF_INT_ENA : R/W ;bitpos:[2] ;default: 1'b0 ; */
/*description: The interrupt enable bit for high speed channel2 counter overflow interrupt.*/
#define LEDC_HSTIMER2_OVF_INT_ENA (BIT(2))
#define LEDC_HSTIMER2_OVF_INT_ENA_M (BIT(2))
#define LEDC_HSTIMER2_OVF_INT_ENA_V 0x1
#define LEDC_HSTIMER2_OVF_INT_ENA_S 2
/* LEDC_HSTIMER1_OVF_INT_ENA : R/W ;bitpos:[1] ;default: 1'b0 ; */
/*description: The interrupt enable bit for high speed channel1 counter overflow interrupt.*/
#define LEDC_HSTIMER1_OVF_INT_ENA (BIT(1))
#define LEDC_HSTIMER1_OVF_INT_ENA_M (BIT(1))
#define LEDC_HSTIMER1_OVF_INT_ENA_V 0x1
#define LEDC_HSTIMER1_OVF_INT_ENA_S 1
/* LEDC_HSTIMER0_OVF_INT_ENA : R/W ;bitpos:[0] ;default: 1'b0 ; */
/*description: The interrupt enable bit for high speed channel0 counter overflow interrupt.*/
#define LEDC_HSTIMER0_OVF_INT_ENA (BIT(0))
#define LEDC_HSTIMER0_OVF_INT_ENA_M (BIT(0))
#define LEDC_HSTIMER0_OVF_INT_ENA_V 0x1
#define LEDC_HSTIMER0_OVF_INT_ENA_S 0
#define LEDC_INT_CLR_REG (DR_REG_LEDC_BASE + 0x018C)
/* LEDC_DUTY_CHNG_END_LSCH7_INT_CLR : WO ;bitpos:[23] ;default: 1'h0 ; */
/*description: Set this bit to clear low speed channel 7 duty change done interrupt.*/
#define LEDC_DUTY_CHNG_END_LSCH7_INT_CLR (BIT(23))
#define LEDC_DUTY_CHNG_END_LSCH7_INT_CLR_M (BIT(23))
#define LEDC_DUTY_CHNG_END_LSCH7_INT_CLR_V 0x1
#define LEDC_DUTY_CHNG_END_LSCH7_INT_CLR_S 23
/* LEDC_DUTY_CHNG_END_LSCH6_INT_CLR : WO ;bitpos:[22] ;default: 1'b0 ; */
/*description: Set this bit to clear low speed channel 6 duty change done interrupt.*/
#define LEDC_DUTY_CHNG_END_LSCH6_INT_CLR (BIT(22))
#define LEDC_DUTY_CHNG_END_LSCH6_INT_CLR_M (BIT(22))
#define LEDC_DUTY_CHNG_END_LSCH6_INT_CLR_V 0x1
#define LEDC_DUTY_CHNG_END_LSCH6_INT_CLR_S 22
/* LEDC_DUTY_CHNG_END_LSCH5_INT_CLR : WO ;bitpos:[21] ;default: 1'b0 ; */
/*description: Set this bit to clear low speed channel 5 duty change done interrupt.*/
#define LEDC_DUTY_CHNG_END_LSCH5_INT_CLR (BIT(21))
#define LEDC_DUTY_CHNG_END_LSCH5_INT_CLR_M (BIT(21))
#define LEDC_DUTY_CHNG_END_LSCH5_INT_CLR_V 0x1
#define LEDC_DUTY_CHNG_END_LSCH5_INT_CLR_S 21
/* LEDC_DUTY_CHNG_END_LSCH4_INT_CLR : WO ;bitpos:[20] ;default: 1'b0 ; */
/*description: Set this bit to clear low speed channel 4 duty change done interrupt.*/
#define LEDC_DUTY_CHNG_END_LSCH4_INT_CLR (BIT(20))
#define LEDC_DUTY_CHNG_END_LSCH4_INT_CLR_M (BIT(20))
#define LEDC_DUTY_CHNG_END_LSCH4_INT_CLR_V 0x1
#define LEDC_DUTY_CHNG_END_LSCH4_INT_CLR_S 20
/* LEDC_DUTY_CHNG_END_LSCH3_INT_CLR : WO ;bitpos:[19] ;default: 1'b0 ; */
/*description: Set this bit to clear low speed channel 3 duty change done interrupt.*/
#define LEDC_DUTY_CHNG_END_LSCH3_INT_CLR (BIT(19))
#define LEDC_DUTY_CHNG_END_LSCH3_INT_CLR_M (BIT(19))
#define LEDC_DUTY_CHNG_END_LSCH3_INT_CLR_V 0x1
#define LEDC_DUTY_CHNG_END_LSCH3_INT_CLR_S 19
/* LEDC_DUTY_CHNG_END_LSCH2_INT_CLR : WO ;bitpos:[18] ;default: 1'b0 ; */
/*description: Set this bit to clear low speed channel 2 duty change done interrupt.*/
#define LEDC_DUTY_CHNG_END_LSCH2_INT_CLR (BIT(18))
#define LEDC_DUTY_CHNG_END_LSCH2_INT_CLR_M (BIT(18))
#define LEDC_DUTY_CHNG_END_LSCH2_INT_CLR_V 0x1
#define LEDC_DUTY_CHNG_END_LSCH2_INT_CLR_S 18
/* LEDC_DUTY_CHNG_END_LSCH1_INT_CLR : WO ;bitpos:[17] ;default: 1'b0 ; */
/*description: Set this bit to clear low speed channel 1 duty change done interrupt.*/
#define LEDC_DUTY_CHNG_END_LSCH1_INT_CLR (BIT(17))
#define LEDC_DUTY_CHNG_END_LSCH1_INT_CLR_M (BIT(17))
#define LEDC_DUTY_CHNG_END_LSCH1_INT_CLR_V 0x1
#define LEDC_DUTY_CHNG_END_LSCH1_INT_CLR_S 17
/* LEDC_DUTY_CHNG_END_LSCH0_INT_CLR : WO ;bitpos:[16] ;default: 1'b0 ; */
/*description: Set this bit to clear low speed channel 0 duty change done interrupt.*/
#define LEDC_DUTY_CHNG_END_LSCH0_INT_CLR (BIT(16))
#define LEDC_DUTY_CHNG_END_LSCH0_INT_CLR_M (BIT(16))
#define LEDC_DUTY_CHNG_END_LSCH0_INT_CLR_V 0x1
#define LEDC_DUTY_CHNG_END_LSCH0_INT_CLR_S 16
/* LEDC_DUTY_CHNG_END_HSCH7_INT_CLR : WO ;bitpos:[15] ;default: 1'b0 ; */
/*description: Set this bit to clear high speed channel 7 duty change done interrupt.*/
#define LEDC_DUTY_CHNG_END_HSCH7_INT_CLR (BIT(15))
#define LEDC_DUTY_CHNG_END_HSCH7_INT_CLR_M (BIT(15))
#define LEDC_DUTY_CHNG_END_HSCH7_INT_CLR_V 0x1
#define LEDC_DUTY_CHNG_END_HSCH7_INT_CLR_S 15
/* LEDC_DUTY_CHNG_END_HSCH6_INT_CLR : WO ;bitpos:[14] ;default: 1'b0 ; */
/*description: Set this bit to clear high speed channel 6 duty change done interrupt.*/
#define LEDC_DUTY_CHNG_END_HSCH6_INT_CLR (BIT(14))
#define LEDC_DUTY_CHNG_END_HSCH6_INT_CLR_M (BIT(14))
#define LEDC_DUTY_CHNG_END_HSCH6_INT_CLR_V 0x1
#define LEDC_DUTY_CHNG_END_HSCH6_INT_CLR_S 14
/* LEDC_DUTY_CHNG_END_HSCH5_INT_CLR : WO ;bitpos:[13] ;default: 1'b0 ; */
/*description: Set this bit to clear high speed channel 5 duty change done interrupt.*/
#define LEDC_DUTY_CHNG_END_HSCH5_INT_CLR (BIT(13))
#define LEDC_DUTY_CHNG_END_HSCH5_INT_CLR_M (BIT(13))
#define LEDC_DUTY_CHNG_END_HSCH5_INT_CLR_V 0x1
#define LEDC_DUTY_CHNG_END_HSCH5_INT_CLR_S 13
/* LEDC_DUTY_CHNG_END_HSCH4_INT_CLR : WO ;bitpos:[12] ;default: 1'b0 ; */
/*description: Set this bit to clear high speed channel 4 duty change done interrupt.*/
#define LEDC_DUTY_CHNG_END_HSCH4_INT_CLR (BIT(12))
#define LEDC_DUTY_CHNG_END_HSCH4_INT_CLR_M (BIT(12))
#define LEDC_DUTY_CHNG_END_HSCH4_INT_CLR_V 0x1
#define LEDC_DUTY_CHNG_END_HSCH4_INT_CLR_S 12
/* LEDC_DUTY_CHNG_END_HSCH3_INT_CLR : WO ;bitpos:[11] ;default: 1'b0 ; */
/*description: Set this bit to clear high speed channel 3 duty change done interrupt.*/
#define LEDC_DUTY_CHNG_END_HSCH3_INT_CLR (BIT(11))
#define LEDC_DUTY_CHNG_END_HSCH3_INT_CLR_M (BIT(11))
#define LEDC_DUTY_CHNG_END_HSCH3_INT_CLR_V 0x1
#define LEDC_DUTY_CHNG_END_HSCH3_INT_CLR_S 11
/* LEDC_DUTY_CHNG_END_HSCH2_INT_CLR : WO ;bitpos:[10] ;default: 1'b0 ; */
/*description: Set this bit to clear high speed channel 2 duty change done interrupt.*/
#define LEDC_DUTY_CHNG_END_HSCH2_INT_CLR (BIT(10))
#define LEDC_DUTY_CHNG_END_HSCH2_INT_CLR_M (BIT(10))
#define LEDC_DUTY_CHNG_END_HSCH2_INT_CLR_V 0x1
#define LEDC_DUTY_CHNG_END_HSCH2_INT_CLR_S 10
/* LEDC_DUTY_CHNG_END_HSCH1_INT_CLR : WO ;bitpos:[9] ;default: 1'b0 ; */
/*description: Set this bit to clear high speed channel 1 duty change done interrupt.*/
#define LEDC_DUTY_CHNG_END_HSCH1_INT_CLR (BIT(9))
#define LEDC_DUTY_CHNG_END_HSCH1_INT_CLR_M (BIT(9))
#define LEDC_DUTY_CHNG_END_HSCH1_INT_CLR_V 0x1
#define LEDC_DUTY_CHNG_END_HSCH1_INT_CLR_S 9
/* LEDC_DUTY_CHNG_END_HSCH0_INT_CLR : WO ;bitpos:[8] ;default: 1'b0 ; */
/*description: Set this bit to clear high speed channel 0 duty change done interrupt.*/
#define LEDC_DUTY_CHNG_END_HSCH0_INT_CLR (BIT(8))
#define LEDC_DUTY_CHNG_END_HSCH0_INT_CLR_M (BIT(8))
#define LEDC_DUTY_CHNG_END_HSCH0_INT_CLR_V 0x1
#define LEDC_DUTY_CHNG_END_HSCH0_INT_CLR_S 8
/* LEDC_LSTIMER3_OVF_INT_CLR : WO ;bitpos:[7] ;default: 1'b0 ; */
/*description: Set this bit to clear low speed channel3 counter overflow interrupt.*/
#define LEDC_LSTIMER3_OVF_INT_CLR (BIT(7))
#define LEDC_LSTIMER3_OVF_INT_CLR_M (BIT(7))
#define LEDC_LSTIMER3_OVF_INT_CLR_V 0x1
#define LEDC_LSTIMER3_OVF_INT_CLR_S 7
/* LEDC_LSTIMER2_OVF_INT_CLR : WO ;bitpos:[6] ;default: 1'b0 ; */
/*description: Set this bit to clear low speed channel2 counter overflow interrupt.*/
#define LEDC_LSTIMER2_OVF_INT_CLR (BIT(6))
#define LEDC_LSTIMER2_OVF_INT_CLR_M (BIT(6))
#define LEDC_LSTIMER2_OVF_INT_CLR_V 0x1
#define LEDC_LSTIMER2_OVF_INT_CLR_S 6
/* LEDC_LSTIMER1_OVF_INT_CLR : WO ;bitpos:[5] ;default: 1'b0 ; */
/*description: Set this bit to clear low speed channel1 counter overflow interrupt.*/
#define LEDC_LSTIMER1_OVF_INT_CLR (BIT(5))
#define LEDC_LSTIMER1_OVF_INT_CLR_M (BIT(5))
#define LEDC_LSTIMER1_OVF_INT_CLR_V 0x1
#define LEDC_LSTIMER1_OVF_INT_CLR_S 5
/* LEDC_LSTIMER0_OVF_INT_CLR : WO ;bitpos:[4] ;default: 1'b0 ; */
/*description: Set this bit to clear low speed channel0 counter overflow interrupt.*/
#define LEDC_LSTIMER0_OVF_INT_CLR (BIT(4))
#define LEDC_LSTIMER0_OVF_INT_CLR_M (BIT(4))
#define LEDC_LSTIMER0_OVF_INT_CLR_V 0x1
#define LEDC_LSTIMER0_OVF_INT_CLR_S 4
/* LEDC_HSTIMER3_OVF_INT_CLR : WO ;bitpos:[3] ;default: 1'b0 ; */
/*description: Set this bit to clear high speed channel3 counter overflow interrupt.*/
#define LEDC_HSTIMER3_OVF_INT_CLR (BIT(3))
#define LEDC_HSTIMER3_OVF_INT_CLR_M (BIT(3))
#define LEDC_HSTIMER3_OVF_INT_CLR_V 0x1
#define LEDC_HSTIMER3_OVF_INT_CLR_S 3
/* LEDC_HSTIMER2_OVF_INT_CLR : WO ;bitpos:[2] ;default: 1'b0 ; */
/*description: Set this bit to clear high speed channel2 counter overflow interrupt.*/
#define LEDC_HSTIMER2_OVF_INT_CLR (BIT(2))
#define LEDC_HSTIMER2_OVF_INT_CLR_M (BIT(2))
#define LEDC_HSTIMER2_OVF_INT_CLR_V 0x1
#define LEDC_HSTIMER2_OVF_INT_CLR_S 2
/* LEDC_HSTIMER1_OVF_INT_CLR : WO ;bitpos:[1] ;default: 1'b0 ; */
/*description: Set this bit to clear high speed channel1 counter overflow interrupt.*/
#define LEDC_HSTIMER1_OVF_INT_CLR (BIT(1))
#define LEDC_HSTIMER1_OVF_INT_CLR_M (BIT(1))
#define LEDC_HSTIMER1_OVF_INT_CLR_V 0x1
#define LEDC_HSTIMER1_OVF_INT_CLR_S 1
/* LEDC_HSTIMER0_OVF_INT_CLR : WO ;bitpos:[0] ;default: 1'b0 ; */
/*description: Set this bit to clear high speed channel0 counter overflow interrupt.*/
#define LEDC_HSTIMER0_OVF_INT_CLR (BIT(0))
#define LEDC_HSTIMER0_OVF_INT_CLR_M (BIT(0))
#define LEDC_HSTIMER0_OVF_INT_CLR_V 0x1
#define LEDC_HSTIMER0_OVF_INT_CLR_S 0
#define LEDC_CONF_REG (DR_REG_LEDC_BASE + 0x0190)
/* LEDC_APB_CLK_SEL : R/W ;bitpos:[0] ;default: 1'b0 ; */
/*description: This bit is used to set the frequency of slow_clk. 1'b1:80mhz 1'b0:8mhz*/
#define LEDC_APB_CLK_SEL (BIT(0))
#define LEDC_APB_CLK_SEL_M (BIT(0))
#define LEDC_APB_CLK_SEL_V 0x1
#define LEDC_APB_CLK_SEL_S 0
#define LEDC_DATE_REG (DR_REG_LEDC_BASE + 0x01FC)
/* LEDC_DATE : R/W ;bitpos:[31:0] ;default: 32'h16031700 ; */
/*description: This register represents the version .*/
#define LEDC_DATE 0xFFFFFFFF
#define LEDC_DATE_M ((LEDC_DATE_V)<<(LEDC_DATE_S))
#define LEDC_DATE_V 0xFFFFFFFF
#define LEDC_DATE_S 0
#endif /*_SOC_LEDC_REG_H_ */