SD SPI mode driver
This MR adds functionality to support SD cards connected via SPI interface.
Additionally, two bugs are fixed:
- Definition of `SPI_TRANS_MODE_DIOQIO_ADDR` in spi_master driver
- SD card probing frequency was 4000kHz instead of 400kHz as required by the standard
See merge request !727
gpio_matrix_out function will set output enable for GPIO, seems in gpio_matrix_out there will be a short moment that the chip will output GPIO level.
So we can set GPIO as high before gpio_matrix_out function.
Previously the first call to rmt_driver_uninstall() would remove the interrupt handler,
even if other channels still had the driver installed.
Adds an OS-level lock to control concurrent registration/deregistration of channels.
1. Name change from chopper to carrier, block diagram update, minor changes to example codes
2. mcpwm_reg.h changed, brought uniformity in comments, worked on suggestions, duty to accept float. Some name changes!
3. Minor readme changes and Indetation
4. Minor change: move mcpwm_reg.h and mcpwm_struct.h to new path
5. Minor change: addition of BLDC example code and Readme
6. Name changed from epwm to mcpwm
7. Improve the reg name in mcpwm_struct.h
8. Name change chopper>carrier, deadband>deadtime
component/esp32 : fix dualcore bug
1. When dual core cpu run access DPORT register, must do protection.
2. If access DPORT register, must use DPORT_REG_READ/DPORT_REG_WRITE and DPORT_XXX register operation macro.
See merge request !742
1. When dual core cpu run access DPORT register, must do protection.
2. If access DPORT register, must use DPORT_REG_READ/DPORT_REG_WRITE and DPORT_XXX register operation macro.
I2S driver - fixed support for 24 and 32-bits, fixed tx/rx at the same time
- Modify sample can test with 24, 32-bits audio
- Add i2s sample README
- simply i2s_push function
- change sample rates, bits per sample, channel on fly
See merge request !483
Add support 24, 32 bits
@jxmao optimize i2s_zero_buffer
@jxmao correct config support slave mode
@jxmao correct setup pin support tx/rx at the same time
Enhance pin power
@jxmao add dynamic change number of channels
remove nvs_init
remove start log and enhance power pin setup
using enum for i2s_channel and i2s_bits_per_sample, return ESP_ERR_INVALID_ARG when check params
validate i2s_bits_per_sample and channel
check tx & rx buffer before fill zero
remove checking channel as @jxmao suggest
limit dma buffer
modify i2s pin back to gpio mux before configure gpio matrix, resolve github issue #512
Add support 24, 32 bits
reduce push function
Modify sample can test with 24, 32-bits
Add i2s sample README
Fixed i2s_set_clk got reset sometime
can changes bit-wide while running
Fix sample rate calculation for DAC mode from @jeroen
modify example can change bits per sample every 5 seconds
cleanup
add comment for bytes_per_sample
update as @angus suggestions
Add i2s_set_clk api
I2S driver bug fixed as following log:
@jxmao optimize i2s_zero_buffer
@jxmao correct config support slave mode
@jxmao correct setup pin support tx/rx at the same time
Enhance pin power
@jxmao add dynamic change number of channels
remove nvs_init
remove start log and enhance power pin setup
using enum for i2s_channel and i2s_bits_per_sample, return ESP_ERR_INVALID_ARG when check params
validate i2s_bits_per_sample and channel
check tx & rx buffer before fill zero
remove checking channel as @jxmao suggest
limit dma buffer
modify i2s pin back to gpio mux before configure gpio matrix, resolve github issue #512
limit dma buffer to 4092
change gpio_matrix_*_check to inline function, remove some comments and rename test_i2s function to setup_triangle_sine_waves
for change commit title
