Fix following WiFi bugs:
1. Fix the bug for API_CHECK_ENABLED
2. Fix the bug that wpa2 enterprise sta can connect open AP
3. Fix TKIP/CCMP PN replay attack detection bug
4. Increase buffer number type from uint8_t to uint16_t to support more than 255 buffers
5. Avoid recalculating PMK if esp_wifi_set_config() is not called
6. Fix the bug that WiFi stop leads to task watchdog
7. Fix smartconfig IPC crash
8. Fix the crash bug that sniffer may access flash when cached is disabled
9. Fix 5.5M signal test bug
We fixed some flash bugs in bootloader, but for the users used the old
vrsion bootloader, they can not fix these bugs via OTA, the solution is
add these updates in app startup.
These updates include:
1. SPI flash gpio matrix and drive strength configuration
2. SPI flash clock configuration
3. SPI flash read dummy configuration
4. SPI flash cs timing configuration
5. Update flash id of g_rom_flashchip
1. fix bug bb reset lock flag to avoid bb reset lock unhandle,
may cause assert in vPortCPUReleaseMutexIntsDisabledInternal.
2. fix bug wifi reset mac cause task watch dog timeout
3. fix bug wifi reset mac position
Hardware AES-CBC performance changes:
Release config 11.0MB/sec -> 10.8MB/sec
Debug config 9.4MB/sec -> 9.8MB/sec
(Unrolling the loop to optimize the check improves
performance at -Og, even with the fault check.)
1. resend eb which are pending in g_ic.tx_buf due to channel switch.
2. add lock for mgmg/xon/bcast to protect send from user flush.
3. softap: add check if secondary offset is correct when start softap.
4. softap: in inactive timer handler, add check if child bss is removed to avoid removing it again.
5. disable A-MPDU for non-root.
6. fix reusing a freed eb.
7. fix when node becomes root, it does not record assoc value to nvs.
8. discard unnecessary forwarded group packets.
9. fix toDS state is not updated in time.
10. fix s_sta_cnx_times is not cleared when deinit causes root sends ADD annoucement.
11. root: increase beacon timeout time from 6 seconds to 15 seconds to delay initiation of reconnection.
12. add esp_mesh_get_tsf_time to return TSF time.
13. send the whole routing table multi-times.
14. clear candidate settings if not receive candidate beacon within 8 seconds.
When flash work in DIO Mode, in order to ensure the fast read mode of flash
is a fixed value, we merged the mode bits into address part, and the fast
read mode value is 0 (the default value).
Fixed the case when the first part of log was missed
this was happened when:
* CONFIG_CONSOLE_UART_CUSTOM option is selected (UART1)
* The selected CONSOLE_UART port is used also for the console component
* in code esp_restart() or abort() functions were called.
Backport following WiFi fixes to v3.2:
1. Add support for STA HT2040 coexist management
2. Add support for WPA2 improvements
3. Disallow HT rate when unicast/mcast cipher is TKIP/WEP
4. Add support for signal test
5. Fix the bug that WPS fails when AP is encrypted
1. remove redundant SPI clock settings, use rom functions to set clock.
2. remove redundant SPI cs setup and hold settings.
3. for old 32Mbit psram, cs hold time must only be 0.5T due to the special driving mode.(cs_setup = 0; cs_hold = 0)
4. for new 64Mbit psram, cs hold time is recommended to be 2.5T. (cs_setup = 1, cs_setup_time = 0;cs_hold = 1, cs_hold_time = 1)
1. Softap support multicast and broadcast saving and flushing
when the associated stations enable IEEE80211 legacy power
save(which is called modem sleep in ESP32).
2. Improve the frame saving and flushing mechanism of softap power
save.
Fix following WiFi and coexist bugs:
1. Fix BT disconnecting due to too many reset BB
2. Fix the bug that no TBTT is generated after rx wrong beacon when WiFi/BT coexist
3. Fix a DelBA bug
4. Add out of memory check
5. Fix the bug that STA incorrectly receives packets when scanning in connected status
6. PHY4008: Disable BT TX in force wifi mode, and enable BT TX in un-force wifi mode
1. fix the bug block scan tiemout before scan finish
2. make menuconfig can set the WiFi mgmt short buffer num
3. modify wifi reason code
4. fix the bug PMK recal too long
1. ref_clock used in unit tests occasionally produces time off by ~100
microseconds shortly after being started. Add a delay to let
ref_clock stabilise, until the cause is found.
2. Reduce roundoff error accumulation which would occasionally cause
the test to fail, by choosing an overflow value which can be divided
by APB frequency.
3. Move time sampling part of the test into an IRAM function to
reduce variations due to cache behavior.
4. Remove calculation of "standard deviation" in the test, as what was
calculated was not actually standard deviation, and it did not add any
useful information.
1. call esp_timer_get_time and ref_clock_get in the same order on
start and in the loop
2. disable interrupts when calculating delta between ref_clock
and esp_timer
3. ensure both functions are in cache before calculating the delta
Previously, this compiler flag was not being applied
regardless of CONFIG_SPIRAM_CACHE_WORKAROUND setting.
Explanation: add_compile_options() only applies to
source files added after the function is run, or in
subdirectories added after the function is run. In
this case, no new source files were being added after
this function was run.
The bug will cause memory corrupted (the largest range is from 0x3ffc0000 ~ 0x3ffc8000),
some strange error will happen, like IllegalInstruction, LoadProhibited and .etc.
1. esp32-pico use standard spi driver to access psram
2. for esp32-pico, flash and psram share the clock
3. for esp32-pico, psram cs io can be overwrite via menuconfig
1. Use BIT[7:5] of EID to determine psram size
2. Add ID support for 16Mbit psram
3. Remove module reset on SPI1
4. Confirmed with the vendor that only the old 32Mbit psram need special clock timing. For other psram chips, we should use standard QPI mode.
Files where stack protector is initialized should not be compiled with
stack protector enabled. This was done for Make but missing for CMake.
Fixes https://github.com/espressif/esp-idf/issues/2990.
Fix following WiFi bugs:
1. Fix a crash bug which is caused by WiFi static TX buffer alloc/free.
2. Fix the bug that iphone fails to connect to ESP32 AP by enabling AP BAR receiving.
3. Fix the bug that ESP32 station fails to connect some APs, such as Xiaomi hotspot etc,
after reset.
