1. Store the calibration data to NVS if PHY does full calibration because of calibration data checksum failure
2. Pass the station's mac to PHY for checksum calculation
A new method of workaround an error with DPORT is to ensure that the APB is read and followed by the DPORT register without interruptions and pauses. This fix places this implementation in the IRAM to exclude errors associated with the cache miss.
Add error handling for http client
set ssid password correct with Example_WIFI test, and clear password before free
Fixed the CI failure due to HTTP errror names
1. provide options for bluetooth low power mode
2. provide two options for bluetooth low power clock: main XTAL and external 32kHz XTAL
3. provide function and callbacks to control bluetooth low power mode, including enable/disable sleep, software wakeup request, low power clock settings, check power state, etc
4. modify vhci API vhci_host_send_packet to use blocking mode
5. note that DFS and bluetooth modem sleep can not be used together currently.
Added .rtc_noinit and .noinit section definitions into linker file /esp32/ld/esp32.common.ld.
The macro __NOINIT_ATTR, RTC_NOINIT_ATTR declared in esp32/esp_attr.h file.
Added unit test file to test added behavior for noinit variables and its attributes.
Added documentation changes for new added attributes.
Make some corrections after code review:
The linker file has been corrected to place noinit section before bss_start to make it safer.
Documentation file has been modified to clarify reset behavior of allocated data .
Corrected typos in test_noinit.c and removed assertion of noinit variable to avoid possible issues with ROM boot loader memory allocation.
The linker file has been corrected to place noinit section before bss_start to make it safer.
Documentation file has been modified to clarify reset behavior of allocated data .
Corrected typos in test_noinit.c and removed assertion of noinit variable to avoid possible issues with ROM boot loader memory allocation.
Update test_noinit.c file to address RTCWDT_RTC_RESET reset reason instead of POWERON_RESET.
Test optimized to pass automated unit testing.
esp32: Add .noinit and .rtc_noinit sections to the linker script
Update of general-notes.rst documentation to fomat examples as code and attributes as identifiers.
Test test_noinit.c corrected to pass automated testing (support ofTEST_CASE_MULTIPLE_STAGES())
https://ezredmine.espressif.cn:8765/issues/15878
1. remove rc when ap not found
closes issue: https://github.com/espressif/esp-idf/issues/1797
2. allocate mimo packet to internal memory
3. use FRC2 timer instead of WDEV_NOW() for modem sleep to calculate
TBTT time.
It fixes the bug that TBTT will be incorrect if beacon is lost.
If the RTC crystal is bad or has no matched capacitance, then you do not need to start such the crystal. It is necessary to determine this case, output an error (about impossibility to start from the oscillator) and start from the internal RC of the chain.
Reduced the default value of the number of bootstrap cycles. Because we can oscillating the oscillator which then stops. (in Kconfig). Changed from 100 to 5.
The number of calibration cycles has been increased. It is the main criterion for estimating the launch of an oscillator. A large increase leads to an increase in the load time, as well as the stability of recognition of this case. (in Kconfig).
Changed from 1024 to 3000.
When two CPUs read the area of the DPORT and the area of the APB, the result is corrupted for the CPU that read the APB area.
And another CPU has valid data.
The method of eliminating this error.
Before reading the registers of the DPORT, make a preliminary reading of the APB register.
In this case, the joint access of the two CPUs to the registers of the APB and the DPORT is successful.
If the allocated interrupt list is not empty and the new item will be inserted
as the header of the list, insert_vector_desc() causes crash because pre is
null. This commit fix this issue.
change some API function to throw event:
esp_wifi_deauth_sta
esp_wifi_get_country
esp_wifi_ap_get_sta_list
esp_wifi_sta_get_ap_info
esp_wifi_stop
esp_wifi_get_channel
esp_wifi_get_protocol
esp_wifi_get_bandwidth
When light sleep is started, the other CPU gets halted using DPORT
stall mechanism. This can happen while it is inside an esp_timer
critical section, which may lead to a deadlock. This change adds
functions to take and release esp_timer lock before entering
DPORT critical section, preventing the deadlock.
1. Add error log if failed to store calibration version/mac/data
2. Change the NVS calibration version/mac/data store sequence
3. Pass the init_data instead of NULL to esp_phy_rf_init() in esp_phy_load_cal_and_init()
1. Bootloader reads SPI configuration from bin header, so that the burning configuration can be different with compiling configuration.
2. Psram mode init will overwrite original flash speed mode, so that users can change psram and flash speed after OTA. 3. Flash read mode(QIO/DIO…) will not be changed in app bin. It is decided by bootloader, OTA can not change this mode.
4. Add read flash ID function, and save flash ID in g_rom_flashchip
5. Set drive ability for all related GPIOs
6. Check raise VDDSDIO voltage in 80Mhz mode
7. Add check flash ID and update settings in bootloader
8. Read flash ID once and keep in global variable
9. Read flash image header once and reuse the result
Tested cases:
1. Test new and old version of bootloader
boot Flash 20M —> app Flash 80M + Psram 80M
boot Flash 40M —> app Flash 80M + Psram 80M
boot Flash 80M —> app Flash 80M + Psram 80M
boot Flash 20M —> app Flash 80M + Psram 40M
boot Flash 40M —> app Flash 80M + Psram 40M
boot Flash 80M —> app Flash 80M + Psram 40M
boot Flash 20M —> app Flash 40M + Psram 40M
boot Flash 40M —> app Flash 40M + Psram 40M
boot Flash 80M —> app Flash 40M + Psram 40M 2. Working after esp_restart reboot.
* Move smartconfig to its component directory, it should be possible to override
this as whole component
* Fix few header includes related to lwIP networking stack
Signed-off-by: Mahavir Jain <mahavir@espressif.com>
1. fix issues on sending beacon caused by too much tx retries on other packets.
2. modify not to scan if rc exists when connect.
3. modify scan dwell time to default 120ms fo root.
1. fix a bug in initliazing map beacon interval.
2. fix not send MESH_EVENT_ROUTING_TABLE_REMOVE when MESH_NWK_CHILD_DISCONNECTED.
3. fix a bug in returning roots ie len.
The files updated according to code review discussions.
In the sleep_modes.c removed immidiate disable of ULP mode and leave just trigger deactivation.
The esp_sleep.h is updated to have the same defines for source as esp_sleep_wakeup_cause_t.
Updated documentation in sleep_modes.rst file to include cross references and address esp_sleep_wakeup_cause_t type.
The get_time_ms() is updated to explicitly use fabs(dt) instead of abs(dt) in test_sleep.c.
Some other minor changes in test_sleep.c unit test.
(TW#18952)
Closes https://github.com/espressif/esp-idf/issues/1677
It is not possible to generate 1 MHz REF_TICK from 2 MHz APB clock
(this is a limitation of REF_TICK divider circuit). Since switching
REF_TICK frequency is something we would like to avoid (to maintain
UART output even with DFS), 2 MHz frequency has been marked as
unsupported.
The issue would manifest itself in cases when switching from PM
configuration like {active=160MHz, idle=80MHz} to {active=80MHz,
idle=80Mhz}. After the configuration was changed, PM logic would
think that current frequency was 80MHz and would not do any further
switching. In fact, frequency was still 160MHz.
The old code calculated MAX() of two enum values, but CPU frequency
enum values are not ordered (2MHz goes after 240MHz). This caused
incorrect configuration to be set.
1. External 32kHz crystal is started for too long or it may not start at all. It is often observed at the first start.
2. At the first start, it is possible that the crystal did not start. And the recorded period was recorded as 0. Which led to a division error by zero during the transition to the deep sleep mode (Maybe somewhere else).
3. Added a unit test to test a new method of oscillation an external crystal.
4. Added a new method of oscillating of an external crystal. The legs of the crystal are fed with a 32 kHz frequency.
The new method eliminates these errors.
Added unit test: `\esp-idf\components\soc\esp32\test\test_rtc_clk.c`: `make TEST_COMPONENTS=soc`
- 8 Test starting external RTC crystal. Will pass.
`Bootstrap cycles for external 32kHz crystal` - is specified in the file Kconfig by default 100.
QA tested a new method of oscillation the crystal on 25 boards. The supply of square waves on the crystal showed a 100% result in contrast to the previous method of launching the crystal. After the tests, the old method was deleted.
Closes TW19143
- separate mode stats from lock stats by an extra comment line
- add CPU frequency column to the mode stats
- don’t print a row for light sleep if light sleep is not enabled
s_cpu_freq_by_mode array was statically initialised with 80MHz CPU
frequency in CPU_MAX and APB_MAX modes, but sdkconfig setting for the
CPU frequency could have been different. For the case of 240MHz CPU
frequency, this would cause a frequency switch between 240MHz and
80MHz to happen, even though such switch is not supported in the fast
path switching functions used by the DFS implementation.
This fixes the issue by moving initialisation into esp_pm_impl_init,
which is called at startup before the first mode switch can happen.
Fixes https://github.com/espressif/esp-idf/issues/1729.
The files updated according to code review discussions.
In the sleep_modes.c removed immidiate disable of ULP mode and leave just trigger deactivation.
The esp_sleep.h is updated to have the same defines for source as esp_sleep_wakeup_cause_t.
Updated documentation in sleep_modes.rst file to include cross references.
Some minor changes in test_sleep.c unit test.
(TW#18952)
Closes https://github.com/espressif/esp-idf/issues/1677
Added function esp_sleep_disable_wakeup_source() to deactivate wakeup trigger for selected source.
Updated documentation for this function in sleep_modes.rst file.
Updated unit test to check this functionality for light sleep.
The test_sleep.c unit test is updated to add reliability for unit testing.
(TW#18952)
Closes https://github.com/espressif/esp-idf/issues/1677
The timer wakeup function once activated cannot be disabled later using existing api. If user wants to use different wakeup sources after first sleep but it does not work. This change disables timer wakeup trigger in configuration that will be set into appropriate RTC registers in esp_light_sleep_start() function.
Added function esp_sleep_disable_wakeup_source() to deactivate wakeup trigger for selected source.
Updated documentation for this function in sleep_modes.rst file to pass make html.
Updated unit test to check this functionality for light sleep.
The test_sleep.c unit test is updated to add reliability for auto unit testing.
(TW#18952)
Closes https://github.com/espressif/esp-idf/issues/1677
tools/gen_esp_err_to_name.py generates
components/esp32/esp_err_to_name.c for lookup of the error codes from
all of the IDF project and easily identify all codes in one place
1. Put some lwip udp rx/tx relating functions to IRAM
2. Put some wifi rx/tx relating functions to IRAMa
3. Reduce wifi dynamic malloc from 4 to 1 for each ebuf
4. Update iperf example accordingly
5. Update libphy.a to v383
close github issue#1037 WiFi Promiscuous filter breaks w/
WIFI_PROMIS_FILTER_MASK_ALL and issue#1404
esp_wifi_set_promiscuous_filter set WIFI_PROMIS_FILTER_MASK_ALL error
When INT WDT fires, panicHandler is invoked. In OCD mode, panicHandler
sets a breakpoint on the PC from the exception frame and returns.
However in case of INT WDT, interrupt flag is still set in TIMERG1
peripheral, which causes INT WDT to trigger again. This causes an
endless stream of "Core 0 panic'ed (Interrupt wdt timeout on CPU1)"
messages. OpenOCD also gets terribly confused at this point.
Disable watchdogs when exiting panic handler in OCD mode.
Clear TIMERG1 WDT interrupt flag to prevent re-entry into panic handler.
libc time function now rely on esp_timer_get_time as the source of
high-resolution time, rather than FRC1 timer. Internally, on the ESP32
esp_timer implementation uses FRC2 timer.
- Change help text and labels in Kconfig to use "high-resolution timer"
instead of FRC1. Keep existing Kconfig option name to be backwards
compatible.
- Change references to "FRC1" in the source code to "FRC".
A function to change "in IRAM" status for an existing interrupt handle, without going through free/allocate of the interrupt.
mOS HW timer implementation requires this to make HW timers safe to re-set from an IRAM ISR.
1. Add a hide API for station to receive and process probe request
frame.
2. Fix an issue that wifi/bt coexistence crashes in PSRAM version.
3. Fix an issue that the API for clearing vendor ie can not work.
4. Fix an issue that wifi stop and reboot leads watchdog.
Timer callback can delete the timer. If CONFIG_ESP_TIMER_PROFILING was
enabled, this caused an access to invalid (freed) memory.
This fix adds a pointer to track the timer while executing the callback.
This is needed so that we can check if callback deletes the timer,
in which case we won't try updating profiling counters for this timer
after the callback is done.
