1. fix some bugs by previous coex hw blocking bugfix,
such like, rwble.c (64, 0) line 222
2. fix bug that ble scan performance is very low when software coexist
is working.
3. update libcoexist version to v1.1.0
1. remove use EID to distinguish psram voltage
2. 1V8 64Mbit psram and 3V3 64Mbit psram use the same psram driver(standard spi interface)
3. set cs hold time register as 1
1. Add reading psram EID.
2. Configure different clock mode for different EID.
3. add API to get psram size and voltage.
4. Remove unnecessary VSPI claim.
For 32MBit@1.8V and 64MBit@3.3V psram, there should be 2 extra clock cycles after CS get high level.
For 64MBit@1.8 psram, we can just use standard SPI protocol to drive the psram. We also need to increase the HOLD time for CS in this case.
EID for psram:
32MBit 1.8v: 0x20
64MBit 1.8v: 0x26
64MBit 3.3v: 0x46
1. Fix the bug that ESP32 will reject the retry AddBA request frame
if AddBA response frame is failed to sent by WiFi LMAC
2. Fix the bug that AddBA request retrys too frequently
3. Forbid BA session setup for VO queue related TID
Routine `spi_flash_cache2phys` sometimes return incorrect value,
resulting in failure in getting currently running ota partition.
This in turn aborts firmware update process.This issue was more
prominent with SPIRAM enabled cases.
Fix ensures proper cache guards during `spi_flash_cache2phys`, and
also for few other similar APIs.
In addition, `esp_ota_get_running_partition` has also been optimized
to save currently running partition for subsequent invocations.
Fixes https://github.com/espressif/esp-idf/issues/2451
Problem Description
The reporduce steps are as follows:
1.This issue can be reproduced with 4 ESP32 devices, 2 for stations (STA1, STA2) and 2 for soft-AP (AP1, AP2)
2.Configure AP1/AP2 to the same SSID (ssid_xxx)
3.The max allowed WiFi connections of AP1 is configured to 1 and STA1 connects to AP1
4.The AP1 is close to STA2 while AP2 is far away from STA2 (but the STA2 can find the AP2 via scan)
5.STA2 connects ssid_xxx with all scan method
6.The problem will happen on STA2 because it fails to connec AP1 and never connects AP2
Phenmenon
STA fail to connect after send auth or assoc with a wrong status code, but no disconnect event report and can not connect the next one in the envrionment
Root Cause
Because there are some same ssid APs in the evnrionment, when do all channel scan, it will collect all the matched AP in rc list, because rc list is not empty, so it would send disconnect event, however, we didn't do other step such as connect to other one
VNC MR 575
closes https://github.com/espressif/esp-idf/issues/2323
fix the bug following:
1. after disable bluetooth controller, wifi cannot TX/RX any packets.
2. when software coexist working, there's a little ratio cause wifi task
watchdog timeout
3. when software coexist working, there's a little ratio cause bluetooth
cannot receive anything.
feature:
1. add libbtdm_app.a git commit local and remote checking
Known issues:
1. there's still a bug occurs with a very very low ratio cause bluetooth
cannot receive anything. The reproduce interval may great than 3days
~ 1week via 7x24 hours heavy testing.
1. suppport mesh type, mesh ID, router and IE crypt func&key at any time after mesh is initalized.
2. support modify parent at any time after mesh is configured.
3. modify manual networking example.
4. update header file.
5. fix issues in root conflicts handling.
6. add max length of beacon to menuconfig.
7. fix issue when received a beacon without DSSS.
Backport following WiFi fixes to v3.1:
1. Fix AMPDU RX sequence compitability bug
2. Optimize scan capability in all channel scan
3. Fix some modem sleep bugs
4. Update API to set CSI channel filter and HT_LTF data generating
The following commit rewrites the ESP-MESH docs. This commit includes
new diagrams and a structure approach to the mesh docs. Some mesh api references
have also been modified.
Some APs transmit AMPDU and MPDU by turns. Moreover, the sequence
numbers of AMPDU and MPDU are out of order, e.g. MPDU(1253) -
AMPDU(1251, 1252) - MPDU(1254) - AMPDU(1255, 1256). In order to
receive both AMPDU and MPDU in order, MPDU must be reordered with
AMPDU.
1. new APIs: esp_mesh_get_subnet_nodes_num() and esp_mesh_get_subnet_nodes_list().
2. fix hard to find the parent during connect.
3. disable Wi-Fi channel switch function.
4. fix a typo of MESH_EVENT_NO_PARENT_FOUND.
Fix following WiFi bugs:
1. Shouldn't scan when connect
2. Check beacon length in modem sleep
3. Fix the bug that AP may deauth wrong station when inactivity timer expires
4. Fix the bug that WiFi assert the system when receiving empty MCS in association response frame
1. modify parent switch mechanism.
2. fix non-root doesn't clear the layer value in nvs.
3. fix retransmit the remove announcement packets.
4. add API esp_mesh_flush_upstream_packets().
5. automatically adjust passsive scan time based on the change of beacon interval.
Backport following bug fixes to v3.1:
1. Bug fix of may connect to wrong AP in all channel scan
2. Station state machine change and fix ap loss
3. Add compatible to ccmp encryption
4. Update libphy.a to v3960:
4.1 Decrease phy_init time from 900us to 347us in sleep wakeup
4.2 Fix RX STBC initialization
4.3 Modify set_chan function to fix interrupt watchdog issue
5. Fix several wpa2 enterprise issues
5.1 Fix heap corrupted bug
5.2 Fix memory leak bug
5.3 Make wpa2 enterprise thread-safe
Closes https://github.com/espressif/esp-idf/issues/1569
6. Bugfix of coex wifi pm
This change adds a check for compatibility between the nvs version
found on nvs flash and the one assumed by running code during nvs
initialization. Any mismatch is reported to the user using new error
code ESP_ERR_NVS_NEW_VERSION_FOUND.
Since 94250e42a0, UART output is suspended when entering sleep mode
(deep or light sleep). This makes sense for light sleep, where sleep
normally takes small amount of time, and flushing the UART would add
a lot of latency. But this breaks existing behaviour for deep sleep,
where UART output was previously sent out before entering sleep mode.
Closes https://github.com/espressif/esp-idf/issues/2145
1. Move channel to the first row of the table.
2. Remove the condition of HT20/HT40 for they are determined by
secondary channel.
3. Clean up the CSI table.
INTERRUPT and CCOUNT registers will change outside of program control.
Making the inline assembly used to read these registers volatile
indicates this fact to the compiler.
Fixes https://github.com/espressif/esp-idf/issues/2127
1. fix BLE connection missing in coex mode
2. modify other parameters to make coex priority more reasonable
3. fix modem sleep procedure trap cause Wifi disable RF when BT is
working. Such cause that BR/EDR is difficult to be connected, BLE
connection stability decrease and so on.
4. modify BR/EDR coexist duration to imrove BR/EDR connect success
ratio.
5. Due to the hardware coexist bug, BLE scan interval/window should
be less than 0x100(about 160ms). Therefore, it will cause BLE cannot
scan any advertising packet while WiFi have higher priority
behaviour(such like RX beacon, scan, TX/RX VO packets and etc.).
1. add APIs to set/get announce interval values.
2. add API to enable/disable the min rate to 6Mbps for data packages.
3. add APIs to set/get RSSI threshold values.
4. fix ap_loss.
Since commit 94250e4, EXT0 wakeup mechanism, when wakeup level was set
to 0, started waking up chip immediately after entering deep sleep.
This failure was triggered in that commit by a change of
RTC_CNTL_MIN_SLP_VAL (i.e. minimum time in sleep mode until wakeup
can happen) from 128 cycles to 2 cycles.
The reason for this behaviour is related to the way input enable (IE)
signal going into an RTC pad is obtained:
PAD_IE = (SLP_SEL) ? SLP_IE & CHIP_SLEEP : IE,
where SLP_IE, SLP_SEL, and IE are bits of an RTC_IO register related
to the given pad. CHIP_SLEEP is the signal indicating that chip has
entered sleep mode.
The code in prepare_ext{0,1}_wakeup did not enable IE, but did enable
SLP_SEL and SLP_IE. This meant that until CHIP_SLEEP went high, PAD_IE
was 0, hence the input from the pad read 0 even if external signal
was 1. CHIP_SLEEP went high on the 2nd cycle of sleep. So when
RTC_CNTL_MIN_SLP_VAL was set to 2, the input signal from the pad was
latched as 0 at the moment when CHIP_SLEEP went high, causing EXT0
wakeup with level 0 to trigger.
This commit changes the way PAD_IE is enabled: SLP_SEL and SLP_IE are
no longer used, and IE is set to 1. If EXT0 wakeup is used, RTC_IO is
not powered down, so IE signal stays 1 both before CHIP_SLEEP goes
high and after. If EXT1 wakeup is used, RTC_IO may be powered down.
However prepare_ext1_wakeup enables Hold on the pad, locking states
of all the control signals, including IE.
Closes https://github.com/espressif/esp-idf/issues/1931
Closes https://github.com/espressif/esp-idf/issues/2043
Previously the loop in esp_timer_impl_set_alarm was necessary to catch
the case when timer count wraps around (goes from 2^32 - 1 to 0).
Since ALARM_OVERFLOW_VAL was reduced from 2^32 - 1 to 0xefffffff,
this is no longer necessary.
Fixes https://github.com/espressif/esp-idf/issues/1891
Allows you to move the partition table, it gives more space for the bootloader.
Added a new utility - parttool.py. This utility can search for the offset and/or size of the partitions by name and type/subtype. Use for getting APP_OFFSET and PHY_DATA_OFFSET.
The linker(esp32.bootloader.ld) made changes that allow you to write a custom bootloader code more.
TW14125
Before entering the deep sleep, the RTC and FRC counters are synchronized. Updating the boot_time.
Added a unit test for this case.
Fixed warnings for MULTIPLE_STAGES
Closes https://github.com/espressif/esp-idf/issues/1840
1. Fix the WiFi/BT coexist bug
2. Fix WPA2 enterprise example crash bug
3. Add size and version check for crypto type struct
4. Add MD5 check for crypto type header file
1. add mesh_assoc_t to esp_mesh_internal.h file.
2. rename "node" to "device" in esp_mesh.h.
3. add MESH_EVENT_SCAN_DONE event.
4. add APIs esp_mesh_scan_get_ap_record() and esp_mesh_scan_get_ap_ie_len() to get scan results.
5. modify API esp_mesh_set_self_organized() by adding parameter "select_parent".
6. modify API esp_mesh_set_parent() by adding parameter "parent_mesh_id"
7. add manual networking example.
1. Store the calibration data to NVS if PHY does full calibration because of calibration data checksum failure
2. Pass the station's mac to PHY for checksum calculation
A new method of workaround an error with DPORT is to ensure that the APB is read and followed by the DPORT register without interruptions and pauses. This fix places this implementation in the IRAM to exclude errors associated with the cache miss.
Add error handling for http client
set ssid password correct with Example_WIFI test, and clear password before free
Fixed the CI failure due to HTTP errror names
1. provide options for bluetooth low power mode
2. provide two options for bluetooth low power clock: main XTAL and external 32kHz XTAL
3. provide function and callbacks to control bluetooth low power mode, including enable/disable sleep, software wakeup request, low power clock settings, check power state, etc
4. modify vhci API vhci_host_send_packet to use blocking mode
5. note that DFS and bluetooth modem sleep can not be used together currently.
Added .rtc_noinit and .noinit section definitions into linker file /esp32/ld/esp32.common.ld.
The macro __NOINIT_ATTR, RTC_NOINIT_ATTR declared in esp32/esp_attr.h file.
Added unit test file to test added behavior for noinit variables and its attributes.
Added documentation changes for new added attributes.
Make some corrections after code review:
The linker file has been corrected to place noinit section before bss_start to make it safer.
Documentation file has been modified to clarify reset behavior of allocated data .
Corrected typos in test_noinit.c and removed assertion of noinit variable to avoid possible issues with ROM boot loader memory allocation.
The linker file has been corrected to place noinit section before bss_start to make it safer.
Documentation file has been modified to clarify reset behavior of allocated data .
Corrected typos in test_noinit.c and removed assertion of noinit variable to avoid possible issues with ROM boot loader memory allocation.
Update test_noinit.c file to address RTCWDT_RTC_RESET reset reason instead of POWERON_RESET.
Test optimized to pass automated unit testing.
esp32: Add .noinit and .rtc_noinit sections to the linker script
Update of general-notes.rst documentation to fomat examples as code and attributes as identifiers.
Test test_noinit.c corrected to pass automated testing (support ofTEST_CASE_MULTIPLE_STAGES())
https://ezredmine.espressif.cn:8765/issues/15878
1. remove rc when ap not found
closes issue: https://github.com/espressif/esp-idf/issues/1797
2. allocate mimo packet to internal memory
3. use FRC2 timer instead of WDEV_NOW() for modem sleep to calculate
TBTT time.
It fixes the bug that TBTT will be incorrect if beacon is lost.
If the RTC crystal is bad or has no matched capacitance, then you do not need to start such the crystal. It is necessary to determine this case, output an error (about impossibility to start from the oscillator) and start from the internal RC of the chain.
Reduced the default value of the number of bootstrap cycles. Because we can oscillating the oscillator which then stops. (in Kconfig). Changed from 100 to 5.
The number of calibration cycles has been increased. It is the main criterion for estimating the launch of an oscillator. A large increase leads to an increase in the load time, as well as the stability of recognition of this case. (in Kconfig).
Changed from 1024 to 3000.
When two CPUs read the area of the DPORT and the area of the APB, the result is corrupted for the CPU that read the APB area.
And another CPU has valid data.
The method of eliminating this error.
Before reading the registers of the DPORT, make a preliminary reading of the APB register.
In this case, the joint access of the two CPUs to the registers of the APB and the DPORT is successful.
If the allocated interrupt list is not empty and the new item will be inserted
as the header of the list, insert_vector_desc() causes crash because pre is
null. This commit fix this issue.
change some API function to throw event:
esp_wifi_deauth_sta
esp_wifi_get_country
esp_wifi_ap_get_sta_list
esp_wifi_sta_get_ap_info
esp_wifi_stop
esp_wifi_get_channel
esp_wifi_get_protocol
esp_wifi_get_bandwidth
When light sleep is started, the other CPU gets halted using DPORT
stall mechanism. This can happen while it is inside an esp_timer
critical section, which may lead to a deadlock. This change adds
functions to take and release esp_timer lock before entering
DPORT critical section, preventing the deadlock.
1. Add error log if failed to store calibration version/mac/data
2. Change the NVS calibration version/mac/data store sequence
3. Pass the init_data instead of NULL to esp_phy_rf_init() in esp_phy_load_cal_and_init()
* Philosophical: "explicit is better than implicit".
* Practical: Allows useful errors if invalid directories given in components as the defaults aren't
always used. Also trims the -I path from a number of components that have no actual include
directory.
* Simplifies knowing which components will be header-only and which won't