esp32: update libphy.a to fix interrupt watchdog when WiFi and BT run at the same time and both enable modem sleep (backport v3.2)
See merge request idf/esp-idf!4192
Shortcircuit evaluation may cause skip of _mdns_strdup_check of any further question field, which after clear_rx_packet freed undefined memory.
Fixes https://ezredmine.espressif.cn:8765/issues/28465
Originally, when doing BLE active scan, Bluedroid will not report adv to
application layer until receive scan response. This option is used to
disable the behavior. When enable this option, Bluedroid will report
adv data or scan response to application layer immediately.
1. fix network channel switch function.
2. support not configuring the network channel.
3. support not configuring the router BSSID even if the router is hidden.
4. add allow_channel_switch to mesh configuration.
5. add allow_router_switch to mesh router configuration.
6. support handling beacon without IE of DS Parameter Set.
7. fix Wi-Fi RX fails in a specific scenario (update libphy.a).
8. fix STAs can not detect disconnection from AP when encrypt transmission is used.
9. fix can not find hidden APs.
10. for root, modify the active scan time to 120ms.
11. remove all rc when clear parent Wi-Fi configuration.
12. fix memory leak caused by the remove announcement being sent is not released when esp_mesh_stop() is called.
13. fix modify IE encrypt after mesh is started.
14. ignore esp_mesh_connect() if mesh automatic reconnection is enabled.
15. fix reason is cleared before vote is done.
16. fix issues in the example of manual_networking when mesh network is encrypted.
17. detect and fix root conflicts when router BSSID is not set.
18. when root can not connect to the router due to NO_MORE_STAS(reason code:5), root will stop re-connection and perform MESH_NWK_LOOK_FOR_NETWORK.
19. wifi: fix the disconnection caused by receiving a deauth frame from non-parent node during scanning.
20. fix routing table redundant issue due to the remove announcement is not 100% reliable.
21. modify the max routes limitation from 300 to 1000.
22. wifi: fix ap does not deauth the sta which has not yet completed the 4-way handshake but the max replay count is reached.
Previously, hardware SHA engine "locks" were mutex semaphores. This meant that the task which
started a particular SHA session (in hardware) needed to finalise that session, or an invalid
FreeRTOS state was created.
Replace with binary semaphore which can be shared between tasks.
Includes a unit test, but unit test doesn't crash even without this fix
(some other unknown condition is required).
Bootloader used to calculate the number of cache pages assuming that
load address was aligned, while in reality load address for DROM and
IROM was offset by 0x20 bytes from the start of 64kB page. This
caused the bootloader to map one less page if the size of the image
was 0x4..0x1c less than a multiple of 64kB.
Reported in https://esp32.com/viewtopic.php?f=13&t=6952.
If zero-overhead loop buffer is enabled, under certain rare conditions
when executing a zero-overhead loop, the CPU may attempt to execute an invalid instruction. Work around by disabling the buffer.
Due to a hardware limitation in ESP32, the first four bytes of some
CSI data is invalid, not the last four bytes.
Correct a mistake of CSI sub-carrier index in documentation.
closes https://github.com/espressif/esp-idf/issues/2494
closes https://github.com/espressif/esp-idf/pull/2493
closes https://github.com/espressif/esp-idf/pull/2496
1. Change bus reset to handle interrupted READ sequences.
2. Slow down I2C to 100khz during reset
3. If a SLAVE device was in a read operation when the bus was interrupted, the SLAVE device is controlling SDA.The only bit during the 9 clock cycles of a byte READ the MASTER(ESP32) is guaranteed control over, is during the ACK bit period.
If the SLAVE is sending a stream of ZERO bytes, it will only release SDA during the ACK bit period. The master(ESP32) cannot generate a STOP unless SDA is HIGH. So, this reset code synchronizes the bit stream with, Either, the ACK bit, Or a 1 bit.
I am stealing this delay coding from @jeremyherbert #2493 pr.
2. Change Bus Reset to handle interrupted READ sequences.
The current code does not handle interrupted READ cycles.
If a SLAVE device was in a read operation when the bus was interrupted, the SLAVE device is controlling SDA.
The only bit during the 9 clock cycles of a byte READ the MASTER(ESP32) is guaranteed control over, is during the ACK bit period.
If the SLAVE is sending a stream of ZERO bytes, it will only release SDA during the ACK bit period. The master(ESP32) cannot generate a STOP unless SDA is HIGH.
So, this reset code synchronizes the bit stream with, Either, the ACK bit, Or a 1 bit.
3. fix typo
correct `sda_id` to `sda_io` in `i2c_master_clear_bus()` @ryan-ma found it. This typo was generated when I manually edited this patch on GitHub, I should have done a Copy/Paste operation!
1. fix bug PHY/RTC functions called in ISR (update phy to v4007)
2. add UnitTest to test it
3. fix task watchdog bug when wifi change channel
4. disable/enable agc to mac deinit/init
tools: Be more helpful to MSYS32 users with package installation & check if current python is inside virtual environment (backport v3.2)
See merge request idf/esp-idf!4063
state and reduce force receiving broadcast data time
1. If receiving beacon which indicates that there is no data buffered,
do not force to receive WiFi data.
2. If receiving beacon which indicates that there is broadcast data
buffered, reduce the time to force receiving broadcast data.
