Even if frame->exccause != PANIC_RSN_CACHEERR, it is possible that
the cache error interrupt status is set. For example, this may happen
due to an invalid cache access in the panic handler itself.
Check cache error interrupt status instead of frame->exccause to
decide whether to do CPU reset or digital reset.
Also remove unnecessary esp_dport_access_int_pause from
esp_cache_err_get_cpuid, since the panic handler already calls
esp_dport_access_int_abort on entry.
arg1 = MAX(int64_t arg1, uint64_t arg2) gave the wrong result, if arg1 < 0, it was presented as a larger value.
And ALARM_REG = (uin32_t)arg1. This leads to an infinite loop.
Fixed: both args are int64_t.
Closes: WIFI-1511
1. Fix WiFi scan leads to poor performance of Bluetooth.
2. Improve WiFi connect success ratio when coexist with Bluetooth.
3. Check if WiFi is still connected when CSA or beacon timeout happen.
4. add coex pre init
Sometimes, libphy.a call phy_enter_critical() to protect accessing critical sections, such like
operating on I2C, but it may not effect when both the CPU core call it. It may cause accessing
I2C blocking and cannot recover by esp_restart(), until do HW reboot.
The workaround for PSRAM that will occupy an SPI bus is enabled only when:
1. used on 32MBit ver 0 PSRAM.
2. work at 80MHz.
The test used to only check 32MBit by the config option, but for PSRAM
on Wrover-B module seems to use a newer version of 32MBit PSRAM. So it
expects the workaround to be enabled, but actually not.
This commit split the unit test into two parts:
1. check all SPI buses are available, for all configs except psram_hspi
and psram_vspi, run on regular runners (including Wrover and Wrover-B).
a hidden option is enabled so that the compiler knows it's not building
psram_hspi or psram_vspi.
2. check the specified bus are acquired, for config psram_hspi and
psram_vspi. This only run on special runner (legacy Wrover module).
1. Fix high beacon and broadcast packets loss ratio of WiFi to make
MDNS test pass.
2. Improve stability of WiFi performance with a little
sacrifice of throughput.
3. Improve BLE advertising and connection performance with dynamic
priority. It sacrifices a little WiFi throughput, but achieves balance
between WiFi and Bluetooth.
4. fix bug bb reset lock flag to avoid bb reset lock unhandle
5. fix bug wifi reset mac cause task watch dog timeout
6. fix bug wifi reset mac position
1. Since BLE full-scan feature for BLE mesh change the controller code cause this problem,
it cause coex semaphore take in "interrupt disable", then it may cause task schedule
and cause crash in freertos
2. Fix newlib lock ISR context and critical section check
3. Fix bt controller ISR context and critical section check
Fix following WiFi bugs:
1. Fix the bug that wpa2 enterprise sta can connect open AP
2. Fix TKIP/CCMP PN replay attack detection bug
3. Increase buffer number type from uint8_t to uint16_t to support more than 255 buffers
4. Avoid recalculating PMK if esp_wifi_set_config() is not called
5. Fix the bug that scan done leads to crash because of uint8 overflow
6. Fix 5.5M signal test bug
Bugfixes:
- Fix http url redirection issue
- Fix basic/digest auth issue with http url
Features:
- Add support for adding custom http header
- Add support for reading firmware image header
- Add support for monitoring upgrade status
- This requires breaking down esp_https_ota API such that it allows finer application level control
- For simpler use-cases previous API is still supported
Closes https://github.com/espressif/esp-idf/issues/3218
Closes https://github.com/espressif/esp-idf/issues/2921
1.Fix the bug that WiFi stop leads to task watchdog(526c6956)
2.Fix the WiFi init sequence bug
3.Fix smartconfig ipc crash
4.Put g_promis_buf to IRAM
5.esp_wifi_set_channel should return error when sniffer is not enabled
6.fix the bug when set WEP authmode or wrong authmode, there is no error return
7.fix the bug that STA parse authmode wrong when AP sets WPA_WPA2_PSK mode
8.fix the bug that wrong error code and wrong event when there is an auto AP in multi-ssid case
We fixed some flash bugs in bootloader, but for the users used the old
vrsion bootloader, they can not fix these bugs via OTA, the solution is
add these updates in app startup.
These updates include:
1. SPI flash gpio matrix and drive strength configuration
2. SPI flash clock configuration
3. SPI flash read dummy configuration
4. SPI flash cs timing configuration
5. Update flash id of g_rom_flashchip
Hardware AES-CBC performance changes:
Release config 11.0MB/sec -> 10.8MB/sec
Debug config 9.4MB/sec -> 9.8MB/sec
(Unrolling the loop to optimize the check improves
performance at -Og, even with the fault check.)
1. resend eb which are pending in g_ic.tx_buf due to channel switch.
2. add lock for mgmg/xon/bcast to protect send from user flush.
3. softap: add check if secondary offset is correct when start softap.
4. softap: in inactive timer handler, add check if child bss is removed to avoid removing it again.
5. disable A-MPDU for non-root.
6. fix reusing a freed eb.
7. fix when node becomes root, it does not record assoc value to nvs.
8. discard unnecessary forwarded group packets.
9. fix toDS state is not updated in time.
10. fix s_sta_cnx_times is not cleared when deinit causes root sends ADD annoucement.
11. root: increase beacon timeout time from 6 seconds to 15 seconds to delay initiation of reconnection.
12. add esp_mesh_get_tsf_time to return TSF time.
13. send the whole routing table multi-times.
14. clear candidate settings if not receive candidate beacon within 8 seconds.
When flash work in DIO Mode, in order to ensure the fast read mode of flash
is a fixed value, we merged the mode bits into address part, and the fast
read mode value is 0 (the default value).
Fixed the case when the first part of log was missed
this was happened when:
* CONFIG_CONSOLE_UART_CUSTOM option is selected (UART1)
* The selected CONSOLE_UART port is used also for the console component
* in code esp_restart() or abort() functions were called.
Fix following wpa2 enterprise vulnerability issues:
1. The station can complete 4-way handshake after EAP-FAIL is received
2. The station crashes if EAP-SUCCESS is received before PMK is setup
1. Softap support multicast and broadcast saving and flushing when the associated stations enable IEEE80211 legacy power save(which is called modem sleep in ESP32).
2. Improve the frame saving and flushing mechanism of softap power save.
1. remove redundant SPI clock settings, use rom functions to set clock.
2. remove redundant SPI cs setup and hold settings.
3. for old 32Mbit psram, cs hold time must only be 0.5T due to the special driving mode.(cs_setup = 0; cs_hold = 0)
4. for new 64Mbit psram, cs hold time is recommended to be 2.5T. (cs_setup = 1, cs_setup_time = 0;cs_hold = 1, cs_hold_time = 1)
Linker script generator produces build/esp32/esp32.common.ld from
components/esp32/ld/esp32.common.ld.in
This works fine until IDF is downgraded to V3.1 which uses components/esp32/ld/esp32.common.ld and
doesn't track build/esp32/esp32.common.ld at all.
At this point, the linker runs in the build/esp32 directory and "-T esp32.common.ld" picks up the
linker script generated .ld file, which causes mis-builds.
As reported on forums: https://esp32.com/viewtopic.php?f=13&t=9684&p=40105
