Changes:
KConfig: The option CONFIG_ESP32_RTCDATA_IN_FAST_MEM is added in Kconfig file for esp32 component.
esp32.common.ld: added support of RTC_DATA_ATTR, RTC_RODATA_ATTR data placement into appropriate segment according to Kconfig option.
esp32.ld: linker script is modified to set alias for memory segment selected by Kconfig option to place data. The segments for force placement are added for RTC_FAST_ATTR, RTC_SLOW_ATTR attributes.
esp_attr.h: added new attributes RTC_FAST_ATTR, RTC_SLOW_ATTR for force placement into fest/slow memory.
test_rtc_fast.c: Added unit test cases to check data placement into appropriate memory segment.
Updated documentation for RTC_DATA_ATTR, RTC_FAST_ATTR, RTC_SLOW_ATTR in deep_sleep_stub.rst file.
TW#18001
Closes https://github.com/espressif/esp-idf/issues/1553
The following commit rewrites the ESP-MESH docs. This commit includes
new diagrams and a structure approach to the mesh docs. Some mesh api references
have also been modified.
Some APs transmit AMPDU and MPDU by turns. Moreover, the sequence
numbers of AMPDU and MPDU are out of order, e.g. MPDU(1253) -
AMPDU(1251, 1252) - MPDU(1254) - AMPDU(1255, 1256). In order to
receive both AMPDU and MPDU in order, MPDU must be reordered with
AMPDU.
1. new APIs: esp_mesh_get_subnet_nodes_num() and esp_mesh_get_subnet_nodes_list().
2. fix hard to find the parent during connect.
3. disable Wi-Fi channel switch function.
4. fix a typo of MESH_EVENT_NO_PARENT_FOUND.
esp_reset_reason_init would check for reset reason hint, and
unconditionally set RTC_RESET_CAUSE_REG (which is also
RTC_ENTRY_ADDR_REG) to hint value 0, i.e. 0x80000000. However the ROM
code treats this value as valid deep sleep wake stub entry point, and
tries to jump to it.
Clear RTC_RESET_CAUSE_REG only if it contained a valid reset reason
hint, and simply set the register value to 0 when doing so. Also add
a check to esp_get_deep_sleep_wake_stub function that deep sleep wake
stub entry address must be in IRAM.
Reported in https://esp32.com/viewtopic.php?f=13&t=6919.
Fix following WiFi bugs:
1. Shouldn't scan when connect
2. Check beacon length in modem sleep
3. Fix the bug that AP may deauth wrong station when inactivity timer expires
4. Fix the bug that WiFi assert the system when receiving empty MCS in association response frame
When 32k XTAL was selected as clock source, if the first calibration
attempt failed, the code would fall back to 150kHz internal clock.
Calibration with the internal clock will always succeed.
Therefore `wait` would always be either 0 or 1. Based on this, some
code in this routine can be eliminated.
1. BLE only with 9(max) connection will decrease 3K DRAM
2. BR/EDR only with 7(max) connection will decrease 16K DRAM
3. Any of BLE or BR/EDR connection number decrease will also decrease DRAM consumption
4. Decrease one BLE connection will save about 1KB DRAM
5. Decrease one BR/EDR ACL connection will save about 1.2KB DRAM
6. Decrease one BR/EDR SCO/eSCO will save 2KB DRAM.
7. fix some definition and kconfig
8. remove 1.2k of vhci tx cache and make .bss & .data to heap about 1.4K
9. modify BT Reserved Memory size and modify example to support new bt kconfig
1. modify parent switch mechanism.
2. fix non-root doesn't clear the layer value in nvs.
3. fix retransmit the remove announcement packets.
4. add API esp_mesh_flush_upstream_packets().
5. automatically adjust passsive scan time based on the change of beacon interval.
No longer necessary to keep all reserved addresses in 'soc'.
Means 'soc' does not need to know about 'bt', for example.
Also means that Bluetooth can be enabled in config without any memory being reserved for BT
controller. Only if code calling the BT controller is linked in, will this memory be reserved...
This change adds a check for compatibility between the nvs version
found on nvs flash and the one assumed by running code during nvs
initialization. Any mismatch is reported to the user using new error
code ESP_ERR_NVS_NEW_VERSION_FOUND.
Update libphy.a to v3960:
1. Decrease phy_init time from 900us to 347us in sleep wakeup
2. Fix RX STBC initialization
3. Modify set_chan function to fix interrupt watchdog issue
it will resolve the problem:
1. when bluetooth is running (For example: a2dp sink), wifi station cannot connect to AP easily
2. improve wifi connection success ratio when coexist is working
1. Modify esp_bt_controller_mem_release() to release BTDM BSS and Data to heap if
ESP_BT_MODE_BTDM mode is passed to it
2. Add a new API esp_bt_mem_release() which internally calls
esp_bt_controller_mem_release() with the provided mode and then if mode
is ESP_BT_MODE_BTDM, releases BT BSS and Data to heap.
Background:
For Wi-Fi and BT/BLE applications, for e.g. the usecase is like when
Bluetooth is used for provisioning and once the device is connected to the Wi-Fi
AP, we can turn off Bluetooth completely. In such scenarios, it should be possible to
reclaim all the memory of Bluetooth. Although, currently this does not
happen.
Experiment:
Made the following modifications to examples/bluetooth/gatt_server :
1. Added support of simple_wifi to it
2. Moved all the bluetooth related code under CONFIG_BT_ENABLED config
option
3. Calculated the free heap in 2 similar scenarios:
i. Disabled BT (CONFIG_BT_ENABLED undefined) and checked the free
heap after STA connected
ii. Kept BT enabled and disabled it after STA connected and checked
the free heap
Ideally, the numbers for i., ii. above should have been similar. But
there was a delta of almost 30-31K. (i. > ii.)
4. Through make size-components checked the common BSS for libbta.a and libbtdm_app.a
and found it to be almost 30K. Data is around 1K
Solution:
1. Modified the linker script to mark the BSS and Data for these libraries and
free it when ESP_BT_MODE_BTDM mode is passed to mem release APIs.
2. Verified that the free heap is comparable for i. and ii. above.
Note: It is known that once this is done, Bluetooth can only be used
again post reboot.
Signed-off-by: Hrishikesh Dhayagude <hrishi@espressif.com>
* Fixes some "noreturn" functions in bootloader utils which did return (causing fatal CPU
exceptions).
* Marks bootloader entry as "noreturn", preventing "user code done" from stalling boot
Partial fix for https://github.com/espressif/esp-idf/issues/1814 TW20016
(Comprehensive fix for this issue will be enabling WDT during bootloader, coming shortly.)
1. Move channel to the first row of the table.
2. Remove the condition of HT20/HT40 for they are determined by
secondary channel.
3. Clean up the CSI table.
Fixed the error division on zero.
Also fixed range CONFIG_ESP32_RTC_CLK_CAL_CYCLES in Kconfig.
Fixed a overflow error by TIMG in the function rtc_clk_cal_internal. This error was due to a limit in values TIMG_RTC_CALI_MAX=0x7FFF (to write the slowclk_cycles) and TIMG_RTC_CALI_VALUE=0x1FFFFFF (to read xtal_cycles). Added assert finctions.
Closes https://github.com/espressif/esp-idf/issues/2147
1. Add reading psram EID.
2. Configure different clock mode for different EID.
3. add API to get psram size and voltage.
4. Remove unnecessary VSPI claim.
For 32MBit@1.8V and 64MBit@3.3V psram, there should be 2 extra clock cycles after CS get high level.
For 64MBit@1.8 psram, we can just use standard SPI protocol to drive the psram. We also need to increase the HOLD time for CS in this case.
EID for psram:
32MBit 1.8v: 0x20
64MBit 1.8v: 0x26
64MBit 3.3v: 0x46
Since 94250e42a0, UART output is suspended when entering sleep mode
(deep or light sleep). This makes sense for light sleep, where sleep
normally takes small amount of time, and flushing the UART would add
a lot of latency. But this breaks existing behaviour for deep sleep,
where UART output was previously sent out before entering sleep mode.
Closes https://github.com/espressif/esp-idf/issues/2145
remote_ip was declared to be a pointer to an address that was
overwritten in later stage thus changing the address pointed by remote_ip
esp_smartconfig.h : Fixed a typo. station_config to wifi_config_t
Signed-off-by: Sachin Parekh <sachin.parekh@espressif.com>
components/esp32/ipc.c: In function 'esp_ipc_init':
components/esp32/ipc.c:82:31: error: '%d' directive writing between 1 and 11 bytes into a region of size 5 [-Werror=format-overflow=]
sprintf(task_name,"ipc%d",i);
^~
components/esp32/ipc.c:82:27: note: directive argument in the range [-2147483648, 1]
sprintf(task_name,"ipc%d",i);
^~~~~~~
components/esp32/ipc.c:82:9: note: 'sprintf' output between 5 and 15 bytes into a destination of size 8
sprintf(task_name,"ipc%d",i);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~
INTERRUPT and CCOUNT registers will change outside of program control.
Making the inline assembly used to read these registers volatile
indicates this fact to the compiler.
Fixes https://github.com/espressif/esp-idf/issues/2127
1. fix BLE connection missing in coex mode
2. modify other parameters to make coex priority more reasonable
3. fix modem sleep procedure trap cause Wifi disable RF when BT is
working. Such cause that BR/EDR is difficult to be connected, BLE
connection stability decrease and so on.
4. modify BR/EDR coexist duration to imrove BR/EDR connect success
ratio.
5. Due to the hardware coexist bug, BLE scan interval/window should
be less than 0x100(about 160ms). Therefore, it will cause BLE cannot
scan any advertising packet while WiFi have higher priority
behaviour(such like RX beacon, scan, TX/RX VO packets and etc.).
1. add APIs to set/get announce interval values.
2. add API to enable/disable the min rate to 6Mbps for data packages.
3. add APIs to set/get RSSI threshold values.
4. fix ap_loss.
Since commit 94250e4, EXT0 wakeup mechanism, when wakeup level was set
to 0, started waking up chip immediately after entering deep sleep.
This failure was triggered in that commit by a change of
RTC_CNTL_MIN_SLP_VAL (i.e. minimum time in sleep mode until wakeup
can happen) from 128 cycles to 2 cycles.
The reason for this behaviour is related to the way input enable (IE)
signal going into an RTC pad is obtained:
PAD_IE = (SLP_SEL) ? SLP_IE & CHIP_SLEEP : IE,
where SLP_IE, SLP_SEL, and IE are bits of an RTC_IO register related
to the given pad. CHIP_SLEEP is the signal indicating that chip has
entered sleep mode.
The code in prepare_ext{0,1}_wakeup did not enable IE, but did enable
SLP_SEL and SLP_IE. This meant that until CHIP_SLEEP went high, PAD_IE
was 0, hence the input from the pad read 0 even if external signal
was 1. CHIP_SLEEP went high on the 2nd cycle of sleep. So when
RTC_CNTL_MIN_SLP_VAL was set to 2, the input signal from the pad was
latched as 0 at the moment when CHIP_SLEEP went high, causing EXT0
wakeup with level 0 to trigger.
This commit changes the way PAD_IE is enabled: SLP_SEL and SLP_IE are
no longer used, and IE is set to 1. If EXT0 wakeup is used, RTC_IO is
not powered down, so IE signal stays 1 both before CHIP_SLEEP goes
high and after. If EXT1 wakeup is used, RTC_IO may be powered down.
However prepare_ext1_wakeup enables Hold on the pad, locking states
of all the control signals, including IE.
Closes https://github.com/espressif/esp-idf/issues/1931
Closes https://github.com/espressif/esp-idf/issues/2043
Previously the loop in esp_timer_impl_set_alarm was necessary to catch
the case when timer count wraps around (goes from 2^32 - 1 to 0).
Since ALARM_OVERFLOW_VAL was reduced from 2^32 - 1 to 0xefffffff,
this is no longer necessary.
Fixes https://github.com/espressif/esp-idf/issues/1891
Allows you to move the partition table, it gives more space for the bootloader.
Added a new utility - parttool.py. This utility can search for the offset and/or size of the partitions by name and type/subtype. Use for getting APP_OFFSET and PHY_DATA_OFFSET.
The linker(esp32.bootloader.ld) made changes that allow you to write a custom bootloader code more.
TW14125
Before entering the deep sleep, the RTC and FRC counters are synchronized. Updating the boot_time.
Added a unit test for this case.
Fixed warnings for MULTIPLE_STAGES
Closes https://github.com/espressif/esp-idf/issues/1840
1. Fix the WiFi/BT coexist bug
2. Fix WPA2 enterprise example crash bug
3. Add size and version check for crypto type struct
4. Add MD5 check for crypto type header file
1. add mesh_assoc_t to esp_mesh_internal.h file.
2. rename "node" to "device" in esp_mesh.h.
3. add MESH_EVENT_SCAN_DONE event.
4. add APIs esp_mesh_scan_get_ap_record() and esp_mesh_scan_get_ap_ie_len() to get scan results.
5. modify API esp_mesh_set_self_organized() by adding parameter "select_parent".
6. modify API esp_mesh_set_parent() by adding parameter "parent_mesh_id"
7. add manual networking example.
1. Store the calibration data to NVS if PHY does full calibration because of calibration data checksum failure
2. Pass the station's mac to PHY for checksum calculation
A new method of workaround an error with DPORT is to ensure that the APB is read and followed by the DPORT register without interruptions and pauses. This fix places this implementation in the IRAM to exclude errors associated with the cache miss.
Add error handling for http client
set ssid password correct with Example_WIFI test, and clear password before free
Fixed the CI failure due to HTTP errror names
1. provide options for bluetooth low power mode
2. provide two options for bluetooth low power clock: main XTAL and external 32kHz XTAL
3. provide function and callbacks to control bluetooth low power mode, including enable/disable sleep, software wakeup request, low power clock settings, check power state, etc
4. modify vhci API vhci_host_send_packet to use blocking mode
5. note that DFS and bluetooth modem sleep can not be used together currently.
Added .rtc_noinit and .noinit section definitions into linker file /esp32/ld/esp32.common.ld.
The macro __NOINIT_ATTR, RTC_NOINIT_ATTR declared in esp32/esp_attr.h file.
Added unit test file to test added behavior for noinit variables and its attributes.
Added documentation changes for new added attributes.
Make some corrections after code review:
The linker file has been corrected to place noinit section before bss_start to make it safer.
Documentation file has been modified to clarify reset behavior of allocated data .
Corrected typos in test_noinit.c and removed assertion of noinit variable to avoid possible issues with ROM boot loader memory allocation.
The linker file has been corrected to place noinit section before bss_start to make it safer.
Documentation file has been modified to clarify reset behavior of allocated data .
Corrected typos in test_noinit.c and removed assertion of noinit variable to avoid possible issues with ROM boot loader memory allocation.
Update test_noinit.c file to address RTCWDT_RTC_RESET reset reason instead of POWERON_RESET.
Test optimized to pass automated unit testing.
esp32: Add .noinit and .rtc_noinit sections to the linker script
Update of general-notes.rst documentation to fomat examples as code and attributes as identifiers.
Test test_noinit.c corrected to pass automated testing (support ofTEST_CASE_MULTIPLE_STAGES())
https://ezredmine.espressif.cn:8765/issues/15878
1. remove rc when ap not found
closes issue: https://github.com/espressif/esp-idf/issues/1797
2. allocate mimo packet to internal memory
3. use FRC2 timer instead of WDEV_NOW() for modem sleep to calculate
TBTT time.
It fixes the bug that TBTT will be incorrect if beacon is lost.
If the RTC crystal is bad or has no matched capacitance, then you do not need to start such the crystal. It is necessary to determine this case, output an error (about impossibility to start from the oscillator) and start from the internal RC of the chain.
Reduced the default value of the number of bootstrap cycles. Because we can oscillating the oscillator which then stops. (in Kconfig). Changed from 100 to 5.
The number of calibration cycles has been increased. It is the main criterion for estimating the launch of an oscillator. A large increase leads to an increase in the load time, as well as the stability of recognition of this case. (in Kconfig).
Changed from 1024 to 3000.
When two CPUs read the area of the DPORT and the area of the APB, the result is corrupted for the CPU that read the APB area.
And another CPU has valid data.
The method of eliminating this error.
Before reading the registers of the DPORT, make a preliminary reading of the APB register.
In this case, the joint access of the two CPUs to the registers of the APB and the DPORT is successful.
If the allocated interrupt list is not empty and the new item will be inserted
as the header of the list, insert_vector_desc() causes crash because pre is
null. This commit fix this issue.
change some API function to throw event:
esp_wifi_deauth_sta
esp_wifi_get_country
esp_wifi_ap_get_sta_list
esp_wifi_sta_get_ap_info
esp_wifi_stop
esp_wifi_get_channel
esp_wifi_get_protocol
esp_wifi_get_bandwidth
When light sleep is started, the other CPU gets halted using DPORT
stall mechanism. This can happen while it is inside an esp_timer
critical section, which may lead to a deadlock. This change adds
functions to take and release esp_timer lock before entering
DPORT critical section, preventing the deadlock.
1. Add error log if failed to store calibration version/mac/data
2. Change the NVS calibration version/mac/data store sequence
3. Pass the init_data instead of NULL to esp_phy_rf_init() in esp_phy_load_cal_and_init()
