OVMS3-idf/components/esp32/include/soc/i2c_struct.h

// Copyright 2015-2016 Espressif Systems (Shanghai) PTE LTD
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at

//     http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
#ifndef _SOC_I2C_STRUCT_H_
#define _SOC_I2C_STRUCT_H_
typedef volatile struct {
    union {
        struct {
            uint32_t scl_low_period:14;             /*This register is used to configure the  low level width of SCL clock.*/
            uint32_t reserved14:    18;
        };
        uint32_t val;
    } scl_low_period;
    union {
        struct {
            uint32_t sda_force_out:    1;           /*1：normally output sda data   0: exchange the function of sda_o and sda_oe (sda_o is the original internal output sda signal sda_oe is the enable bit for the internal output sda signal)*/
            uint32_t scl_force_out:    1;           /*1：normally output scl clock  0: exchange the function of scl_o and scl_oe (scl_o is the original internal output scl signal  scl_oe is the enable bit for the internal output scl signal)*/
            uint32_t sample_scl_level: 1;           /*Set this bit to sample data in SCL low level. clear this bit to sample data in SCL high level.*/
            uint32_t reserved3:        1;
            uint32_t ms_mode:          1;           /*Set this bit to configure the module as i2c master  clear this bit to configure the module as i2c slave.*/
            uint32_t trans_start:      1;           /*Set this bit to start sending data in tx_fifo.*/
            uint32_t tx_lsb_first:     1;           /*This bit is used to control the sending mode for  data need to be send. 1：receive data from most significant bit    0：receive data from least significant bit*/
            uint32_t rx_lsb_first:     1;           /*This bit is used to control the storage mode for received data. 1：receive data from most significant bit    0：receive data from least significant bit*/
            uint32_t clk_en:           1;           /*This is the clock gating control bit for reading or writing registers.*/
            uint32_t reserved9:       23;
        };
        uint32_t val;
    } ctr;
    union {
        struct {
            uint32_t ack_rec:             1;        /*This register stores the value of ACK bit.*/
            uint32_t slave_rw:            1;        /*when in slave mode  1：master read slave  0: master write slave.*/
            uint32_t time_out:            1;        /*when I2C takes more than time_out_reg clocks to receive a data then this register changes to high level.*/
            uint32_t arb_lost:            1;        /*when I2C lost control of SDA line  this register changes to high level.*/
            uint32_t bus_busy:            1;        /*1:I2C bus is busy transferring data. 0:I2C bus is in idle state.*/
            uint32_t slave_addressed:     1;        /*when configured as i2c slave  and the address send by master is equal to slave's address  then this bit will be high level.*/
            uint32_t byte_trans:          1;        /*This register changes to high level when one byte is transferred.*/
            uint32_t reserved7:           1;
            uint32_t rx_fifo_cnt:         6;        /*This register represent the amount of data need to send.*/
            uint32_t reserved14:          4;
            uint32_t tx_fifo_cnt:         6;        /*This register stores the amount of received data  in ram.*/
            uint32_t scl_main_state_last: 3;        /*This register stores the value of state machine for i2c module.  3'h0: SCL_MAIN_IDLE  3'h1: SCL_ADDRESS_SHIFT 3'h2: SCL_ACK_ADDRESS  3'h3: SCL_RX_DATA  3'h4 SCL_TX_DATA  3'h5:SCL_SEND_ACK 3'h6:SCL_WAIT_ACK*/
            uint32_t reserved27:          1;
            uint32_t scl_state_last:      3;        /*This register stores the value of state machine to produce SCL. 3'h0: SCL_IDLE  3'h1:SCL_START   3'h2:SCL_LOW_EDGE  3'h3: SCL_LOW   3'h4:SCL_HIGH_EDGE   3'h5:SCL_HIGH  3'h6:SCL_STOP*/
            uint32_t reserved31:          1;
        };
        uint32_t val;
    } status_reg;
    union {
        struct {
            uint32_t tout:      20;                 /*This register is used to configure the max clock number of receiving  a data.*/
            uint32_t reserved20:12;
        };
        uint32_t val;
    } timeout;
    union {
        struct {
            uint32_t addr:       15;                /*when configured as i2c slave  this register is used to configure slave's address.*/
            uint32_t reserved15: 16;
            uint32_t en_10bit:    1;                /*This register is used to enable slave 10bit address mode.*/
        };
        uint32_t val;
    } slave_addr;
    union {
        struct {
            uint32_t rx_fifo_start_addr: 5;         /*This is the offset address of the last receiving data as described in nonfifo_rx_thres_register.*/
            uint32_t rx_fifo_end_addr:   5;         /*This is the offset address of the first receiving data as described in nonfifo_rx_thres_register.*/
            uint32_t tx_fifo_start_addr: 5;         /*This is the offset address of the first  sending data as described in nonfifo_tx_thres register.*/
            uint32_t tx_fifo_end_addr:   5;         /*This is the offset address of the last  sending data as described in nonfifo_tx_thres register.*/
            uint32_t reserved20:        12;
        };
        uint32_t val;
    } fifo_st;
    union {
        struct {
            uint32_t rx_fifo_full_thrhd: 5;
            uint32_t tx_fifo_empty_thrhd:5;         /*Config tx_fifo empty threhd value when using apb fifo access*/
            uint32_t nonfifo_en:         1;         /*Set this bit to enble apb nonfifo access.*/
            uint32_t fifo_addr_cfg_en:   1;         /*When this bit is set to 1 then the byte after address represent the offset address of I2C Slave's ram.*/
            uint32_t rx_fifo_rst:        1;         /*Set this bit to reset rx fifo when using apb fifo access.*/
            uint32_t tx_fifo_rst:        1;         /*Set this bit to reset tx fifo when using apb fifo access.*/
            uint32_t nonfifo_rx_thres:   6;         /*when I2C receives more than nonfifo_rx_thres data  it will produce rx_send_full_int_raw interrupt and update the current offset address of the receiving data.*/
            uint32_t nonfifo_tx_thres:   6;         /*when I2C sends more than nonfifo_tx_thres data  it will produce tx_send_empty_int_raw interrupt and update the current offset address of the sending data.*/
            uint32_t reserved26:         6;
        };
        uint32_t val;
    } fifo_conf;
    union {
        struct {
            uint8_t data;                           /*The register represent the byte  data read from rx_fifo when use apb fifo access*/
            uint8_t reserved[3];
        };
        uint32_t val;
    } fifo_data;
    union {
        struct {
            uint32_t rx_fifo_full:     1;           /*The raw interrupt status bit for rx_fifo full when use apb fifo access.*/
            uint32_t tx_fifo_empty:    1;           /*The raw interrupt status bit for tx_fifo empty when use apb fifo access.*/
            uint32_t rx_fifo_ovf:      1;           /*The raw interrupt status bit for receiving data overflow when use apb fifo access.*/
            uint32_t end_detect:       1;           /*The raw interrupt status bit for end_detect_int interrupt. when I2C deals with  the END command  it will produce end_detect_int interrupt.*/
            uint32_t slave_tran_comp:  1;           /*The raw interrupt status bit for slave_tran_comp_int interrupt. when I2C Slave detects the STOP bit  it will produce slave_tran_comp_int interrupt.*/
            uint32_t arbitration_lost: 1;           /*The raw interrupt status bit for arbitration_lost_int interrupt.when I2C lost the usage right of I2C BUS it will produce arbitration_lost_int interrupt.*/
            uint32_t master_tran_comp: 1;           /*The raw interrupt status bit for master_tra_comp_int interrupt. when I2C Master sends or receives a byte it will produce master_tran_comp_int interrupt.*/
            uint32_t trans_complete:   1;           /*The raw interrupt status bit for trans_complete_int interrupt. when I2C Master finished STOP command  it will produce trans_complete_int interrupt.*/
            uint32_t time_out:         1;           /*The raw interrupt status bit for time_out_int interrupt. when I2C takes a lot of time to receive a data  it will produce  time_out_int interrupt.*/
            uint32_t trans_start:      1;           /*The raw interrupt status bit for trans_start_int interrupt. when I2C sends the START bit it will produce trans_start_int interrupt.*/
            uint32_t ack_err:          1;           /*The raw interrupt status bit for ack_err_int interrupt. when I2C receives a wrong ACK bit  it will produce ack_err_int interrupt..*/
            uint32_t rx_rec_full:      1;           /*The raw interrupt status bit for rx_rec_full_int interrupt. when I2C receives more data  than nonfifo_rx_thres  it will produce rx_rec_full_int interrupt.*/
            uint32_t tx_send_empty:    1;           /*The raw interrupt status bit for tx_send_empty_int interrupt.when I2C sends more data than nonfifo_tx_thres  it will produce tx_send_empty_int interrupt..*/
            uint32_t reserved13:      19;
        };
        uint32_t val;
    } int_raw;
    union {
        struct {
            uint32_t rx_fifo_full:     1;           /*Set this bit to clear the rx_fifo_full_int interrupt.*/
            uint32_t tx_fifo_empty:    1;           /*Set this bit to clear the tx_fifo_empty_int interrupt.*/
            uint32_t rx_fifo_ovf:      1;           /*Set this bit to clear the rx_fifo_ovf_int interrupt.*/
            uint32_t end_detect:       1;           /*Set this bit to clear the end_detect_int interrupt.*/
            uint32_t slave_tran_comp:  1;           /*Set this bit to clear the slave_tran_comp_int interrupt.*/
            uint32_t arbitration_lost: 1;           /*Set this bit to clear the arbitration_lost_int interrupt.*/
            uint32_t master_tran_comp: 1;           /*Set this bit to clear the master_tran_comp interrupt.*/
            uint32_t trans_complete:   1;           /*Set this bit to clear the trans_complete_int interrupt.*/
            uint32_t time_out:         1;           /*Set this bit to clear the time_out_int interrupt.*/
            uint32_t trans_start:      1;           /*Set this bit to clear the trans_start_int interrupt.*/
            uint32_t ack_err:          1;           /*Set this bit to clear the ack_err_int interrupt.*/
            uint32_t rx_rec_full:      1;           /*Set this bit to clear the rx_rec_full_int interrupt.*/
            uint32_t tx_send_empty:    1;           /*Set this bit to clear the tx_send_empty_int interrupt.*/
            uint32_t reserved13:      19;
        };
        uint32_t val;
    } int_clr;
    union {
        struct {
            uint32_t rx_fifo_full:     1;           /*The enable bit for rx_fifo_full_int interrupt.*/
            uint32_t tx_fifo_empty:    1;           /*The enable bit for tx_fifo_empty_int interrupt.*/
            uint32_t rx_fifo_ovf:      1;           /*The enable bit for rx_fifo_ovf_int interrupt.*/
            uint32_t end_detect:       1;           /*The enable bit for end_detect_int interrupt.*/
            uint32_t slave_tran_comp:  1;           /*The enable bit for slave_tran_comp_int interrupt.*/
            uint32_t arbitration_lost: 1;           /*The enable bit for arbitration_lost_int interrupt.*/
            uint32_t master_tran_comp: 1;           /*The enable bit for master_tran_comp_int interrupt.*/
            uint32_t trans_complete:   1;           /*The enable bit for trans_complete_int interrupt.*/
            uint32_t time_out:         1;           /*The enable bit for time_out_int interrupt.*/
            uint32_t trans_start:      1;           /*The enable bit for trans_start_int interrupt.*/
            uint32_t ack_err:          1;           /*The enable bit for ack_err_int interrupt.*/
            uint32_t rx_rec_full:      1;           /*The enable bit for rx_rec_full_int interrupt.*/
            uint32_t tx_send_empty:    1;           /*The enable bit for tx_send_empty_int interrupt.*/
            uint32_t reserved13:      19;
        };
        uint32_t val;
    } int_ena;
    union {
        struct {
            uint32_t rx_fifo_full:     1;            /*The masked interrupt status for rx_fifo_full_int interrupt.*/
            uint32_t tx_fifo_empty:    1;            /*The masked interrupt status for tx_fifo_empty_int interrupt.*/
            uint32_t rx_fifo_ovf:      1;            /*The masked interrupt status for rx_fifo_ovf_int interrupt.*/
            uint32_t end_detect:       1;            /*The masked interrupt status for end_detect_int interrupt.*/
            uint32_t slave_tran_comp:  1;            /*The masked interrupt status for slave_tran_comp_int interrupt.*/
            uint32_t arbitration_lost: 1;            /*The masked interrupt status for arbitration_lost_int interrupt.*/
            uint32_t master_tran_comp: 1;            /*The masked interrupt status for master_tran_comp_int interrupt.*/
            uint32_t trans_complete:   1;            /*The masked interrupt status for trans_complete_int interrupt.*/
            uint32_t time_out:         1;            /*The masked interrupt status for time_out_int interrupt.*/
            uint32_t trans_start:      1;            /*The masked interrupt status for trans_start_int interrupt.*/
            uint32_t ack_err:          1;            /*The masked interrupt status for ack_err_int interrupt.*/
            uint32_t rx_rec_full:      1;            /*The masked interrupt status for rx_rec_full_int interrupt.*/
            uint32_t tx_send_empty:    1;            /*The masked interrupt status for tx_send_empty_int interrupt.*/
            uint32_t reserved13:      19;
        };
        uint32_t val;
    } int_status;
    union {
        struct {
            uint32_t time:        10;                /*This register is used to configure the clock num I2C used to hold the data after the negedge of SCL.*/
            uint32_t reserved10:  22;
        };
        uint32_t val;
    } sda_hold;
    union {
        struct {
            uint32_t time:       10;                 /*This register is used to configure the clock num I2C used to sample data on SDA after the posedge of SCL*/
            uint32_t reserved10: 22;
        };
        uint32_t val;
    } sda_sample;
    union {
        struct {
            uint32_t period:     14;                 /*This register is used to configure the clock num during SCL is low level.*/
            uint32_t reserved14: 18;
        };
        uint32_t val;
    } scl_high_period;
    uint32_t reserved_3c;
    union {
        struct {
            uint32_t time:       10;                /*This register is used to configure the clock num between the negedge of SDA and negedge of SCL for start mark.*/
            uint32_t reserved10: 22;
        };
        uint32_t val;
    } scl_start_hold;
    union {
        struct {
            uint32_t time:       10;                /*This register is used to configure the clock num between the posedge of SCL and the negedge of SDA for restart mark.*/
            uint32_t reserved10: 22;
        };
        uint32_t val;
    } scl_rstart_setup;
    union {
        struct {
            uint32_t time:       14;                /*This register is used to configure the clock num after the STOP bit's posedge.*/
            uint32_t reserved14: 18;
        };
        uint32_t val;
    } scl_stop_hold;
    union {
        struct {
            uint32_t time:       10;                /*This register is used to configure the clock num between the posedge of SCL and the posedge of SDA.*/
            uint32_t reserved10: 22;
        };
        uint32_t val;
    } scl_stop_setup;
    union {
        struct {
            uint32_t thres:      3;                 /*When input SCL's pulse width is smaller than this register value  I2C ignores this pulse.*/
            uint32_t en:         1;                 /*This is the filter enable bit for SCL.*/
            uint32_t reserved4: 28;
        };
        uint32_t val;
    } scl_filter_cfg;
    union {
        struct {
            uint32_t thres:      3;                 /*When input SCL's pulse width is smaller than this register value  I2C ignores this pulse.*/
            uint32_t en:         1;                 /*This is the filter enable bit for SDA.*/
            uint32_t reserved4: 28;
        };
        uint32_t val;
    } sda_filter_cfg;
    union {
        struct {
            uint32_t byte_num:      8;              /*Byte_num represent the number of data need to be send or data need to be received.*/
            uint32_t ack_en:        1;              /*ack_check_en  ack_exp and ack value are used to control  the ack bit.*/
            uint32_t ack_exp:       1;              /*ack_check_en  ack_exp and ack value are used to control  the ack bit.*/
            uint32_t ack_val:       1;              /*ack_check_en  ack_exp and ack value are used to control  the ack bit.*/
            uint32_t op_code:       3;              /*op_code is the command  0：RSTART   1：WRITE  2：READ  3：STOP . 4:END.*/
            uint32_t reserved14:   17;
            uint32_t done:  1;                      /*When command0 is done in I2C Master mode  this bit changes to high level.*/
        };
        uint32_t val;
    } command[16];
    uint32_t reserved_98;
    uint32_t reserved_9c;
    uint32_t reserved_a0;
    uint32_t reserved_a4;
    uint32_t reserved_a8;
    uint32_t reserved_ac;
    uint32_t reserved_b0;
    uint32_t reserved_b4;
    uint32_t reserved_b8;
    uint32_t reserved_bc;
    uint32_t reserved_c0;
    uint32_t reserved_c4;
    uint32_t reserved_c8;
    uint32_t reserved_cc;
    uint32_t reserved_d0;
    uint32_t reserved_d4;
    uint32_t reserved_d8;
    uint32_t reserved_dc;
    uint32_t reserved_e0;
    uint32_t reserved_e4;
    uint32_t reserved_e8;
    uint32_t reserved_ec;
    uint32_t reserved_f0;
    uint32_t reserved_f4;
    uint32_t date;                                  /**/
    uint32_t reserved_fc;
    uint32_t fifo_start_addr;                       /*This the start address for ram when use apb nonfifo access.*/
} i2c_dev_t;
extern i2c_dev_t I2C0;
extern i2c_dev_t I2C1;
#endif  /* _SOC_I2C_STRUCT_H_ */