OVMS3-idf/components/esp32s2beta/clk.c

// Copyright 2015-2017 Espressif Systems (Shanghai) PTE LTD
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
//
//     http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.

#include <stdint.h>
#include <sys/cdefs.h>
#include <sys/time.h>
#include <sys/param.h>
#include "sdkconfig.h"
#include "esp_attr.h"
#include "esp_log.h"
#include "esp32s2beta/clk.h"
#include "esp_clk_internal.h"
#include "esp32s2beta/rom/ets_sys.h"
#include "esp32s2beta/rom/uart.h"
#include "esp32s2beta/rom/rtc.h"
#include "soc/system_reg.h"
#include "soc/dport_access.h"
#include "soc/soc.h"
#include "soc/rtc.h"
#include "soc/rtc_wdt.h"
#include "soc/rtc_periph.h"
#include "soc/i2s_reg.h"
#include "driver/periph_ctrl.h"
#include "xtensa/core-macros.h"
#include "bootloader_clock.h"
#include "soc/syscon_reg.h"

/* Number of cycles to wait from the 32k XTAL oscillator to consider it running.
 * Larger values increase startup delay. Smaller values may cause false positive
 * detection (i.e. oscillator runs for a few cycles and then stops).
 */
#define SLOW_CLK_CAL_CYCLES     CONFIG_ESP32S2_RTC_CLK_CAL_CYCLES

#define MHZ (1000000)

static void select_rtc_slow_clk(rtc_slow_freq_t slow_clk);

// g_ticks_us defined in ROMs for PRO CPU
extern uint32_t g_ticks_per_us_pro;
static const char *TAG = "clk";


void esp_clk_init(void)
{
    rtc_config_t cfg = RTC_CONFIG_DEFAULT();
    rtc_init(cfg);

    assert(rtc_clk_xtal_freq_get() == RTC_XTAL_FREQ_40M);

    rtc_clk_fast_freq_set(RTC_FAST_FREQ_8M);

#ifdef CONFIG_BOOTLOADER_WDT_ENABLE
    // WDT uses a SLOW_CLK clock source. After a function select_rtc_slow_clk a frequency of this source can changed.
    // If the frequency changes from 90kHz to 32kHz, then the timeout set for the WDT will increase 2.8 times.
    // Therefore, for the time of frequency change, set a new lower timeout value (1.6 sec).
    // This prevents excessive delay before resetting in case the supply voltage is drawdown.
    // (If frequency is changed from 90kHz to 32kHz then WDT timeout will increased to 1.6sec * 90/32 = 4.5 sec).
    rtc_wdt_protect_off();
    rtc_wdt_feed();
    rtc_wdt_set_time(RTC_WDT_STAGE0, 1600);
    rtc_wdt_protect_on();
#endif

#ifdef CONFIG_ESP32S2_RTC_CLK_SRC_EXT_CRYS
    select_rtc_slow_clk(RTC_SLOW_FREQ_32K_XTAL);
#else
    select_rtc_slow_clk(RTC_SLOW_FREQ_RTC);
#endif

#ifdef CONFIG_BOOTLOADER_WDT_ENABLE
    // After changing a frequency WDT timeout needs to be set for new frequency.
    rtc_wdt_protect_off();
    rtc_wdt_feed();
    rtc_wdt_set_time(RTC_WDT_STAGE0, CONFIG_BOOTLOADER_WDT_TIME_MS);
    rtc_wdt_protect_on();
#endif

    uint32_t freq_mhz = CONFIG_ESP32S2_DEFAULT_CPU_FREQ_MHZ;
    rtc_cpu_freq_t freq = RTC_CPU_FREQ_80M;
    switch (freq_mhz) {
    case 240:
        freq = RTC_CPU_FREQ_240M;
        break;
    case 160:
        freq = RTC_CPU_FREQ_160M;
        break;
    case 80:
        freq = RTC_CPU_FREQ_80M;
        break;
    default:
        freq_mhz = 80;
        freq = RTC_CPU_FREQ_80M;
        break;
    }

    // Wait for UART TX to finish, otherwise some UART output will be lost
    // when switching APB frequency
    uart_tx_wait_idle(CONFIG_ESP_CONSOLE_UART_NUM);

    uint32_t freq_before = rtc_clk_cpu_freq_value(rtc_clk_cpu_freq_get()) / MHZ ;

    rtc_clk_cpu_freq_set(freq);

    // Re calculate the ccount to make time calculation correct.
    uint32_t freq_after = CONFIG_ESP32S2_DEFAULT_CPU_FREQ_MHZ;
    XTHAL_SET_CCOUNT( XTHAL_GET_CCOUNT() * freq_after / freq_before );
}

int IRAM_ATTR esp_clk_cpu_freq(void)
{
    return g_ticks_per_us_pro * 1000000;
}

int IRAM_ATTR esp_clk_apb_freq(void)
{
    return MIN(g_ticks_per_us_pro, 80) * 1000000;
}

void IRAM_ATTR ets_update_cpu_frequency(uint32_t ticks_per_us)
{
    /* Update scale factors used by ets_delay_us */
    g_ticks_per_us_pro = ticks_per_us;
}

static void select_rtc_slow_clk(rtc_slow_freq_t slow_clk)
{
    uint32_t cal_val = 0;
    uint32_t wait = 0;
    const uint32_t warning_timeout = 3 /* sec */ * 32768 /* Hz */ / (2 * SLOW_CLK_CAL_CYCLES);
    bool changing_clock_to_150k = false;
    do {
        if (slow_clk == RTC_SLOW_FREQ_32K_XTAL) {
            /* 32k XTAL oscillator needs to be enabled and running before it can
             * be used. Hardware doesn't have a direct way of checking if the
             * oscillator is running. Here we use rtc_clk_cal function to count
             * the number of main XTAL cycles in the given number of 32k XTAL
             * oscillator cycles. If the 32k XTAL has not started up, calibration
             * will time out, returning 0.
             */
            ESP_EARLY_LOGD(TAG, "waiting for 32k oscillator to start up");
            rtc_clk_32k_enable(true);
            cal_val = rtc_clk_cal(RTC_CAL_32K_XTAL, SLOW_CLK_CAL_CYCLES);
            if (cal_val == 0 || cal_val < 15000000L) {
                ESP_EARLY_LOGE(TAG, "RTC: Not found External 32 kHz XTAL. Switching to Internal 150 kHz RC chain");
                slow_clk = RTC_SLOW_FREQ_RTC;
                changing_clock_to_150k = true;
            }
        }
        rtc_clk_slow_freq_set(slow_clk);
        if (changing_clock_to_150k == true && wait > 1) {
            // This helps when there are errors when switching the clock from External 32 kHz XTAL to Internal 150 kHz RC chain.
            rtc_clk_32k_enable(false);
            uint32_t min_bootstrap = 5; // Min bootstrapping for continue switching the clock.
            rtc_clk_32k_bootstrap(min_bootstrap);
            rtc_clk_32k_enable(true);
        }

        if (SLOW_CLK_CAL_CYCLES > 0) {
            /* TODO: 32k XTAL oscillator has some frequency drift at startup.
             * Improve calibration routine to wait until the frequency is stable.
             */
            cal_val = rtc_clk_cal(RTC_CAL_RTC_MUX, SLOW_CLK_CAL_CYCLES);
        } else {
            const uint64_t cal_dividend = (1ULL << RTC_CLK_CAL_FRACT) * 1000000ULL;
            cal_val = (uint32_t) (cal_dividend / rtc_clk_slow_freq_get_hz());
        }
        if (++wait % warning_timeout == 0) {
            ESP_EARLY_LOGW(TAG, "still waiting for source selection RTC");
        }
    } while (cal_val == 0);
    ESP_EARLY_LOGD(TAG, "RTC_SLOW_CLK calibration value: %d", cal_val);
    esp_clk_slowclk_cal_set(cal_val);
}

void rtc_clk_select_rtc_slow_clk(void)
{
    select_rtc_slow_clk(RTC_SLOW_FREQ_32K_XTAL);
}

/* This function is not exposed as an API at this point.
 * All peripheral clocks are default enabled after chip is powered on.
 * This function disables some peripheral clocks when cpu starts.
 * These peripheral clocks are enabled when the peripherals are initialized
 * and disabled when they are de-initialized.
 */
void esp_perip_clk_init(void)
{
    uint32_t common_perip_clk, hwcrypto_perip_clk, wifi_bt_sdio_clk = 0;
    uint32_t common_perip_clk1 = 0;

    RESET_REASON rst_reas[1];

    rst_reas[0] = rtc_get_reset_reason(0);

    /* For reason that only reset CPU, do not disable the clocks
     * that have been enabled before reset.
     */
    if (rst_reas[0] >= TG0WDT_CPU_RESET &&
            rst_reas[0] <= TG0WDT_CPU_RESET &&
            rst_reas[0] != RTCWDT_BROWN_OUT_RESET) {
        common_perip_clk = ~DPORT_READ_PERI_REG(DPORT_PERIP_CLK_EN_REG);
        hwcrypto_perip_clk = ~DPORT_READ_PERI_REG(DPORT_PERI_CLK_EN_REG);
        wifi_bt_sdio_clk = ~DPORT_READ_PERI_REG(DPORT_WIFI_CLK_EN_REG);
    } else {
        common_perip_clk = DPORT_WDG_CLK_EN |
                           DPORT_I2S0_CLK_EN |
#if CONFIG_ESP_CONSOLE_UART_NUM != 0
                           DPORT_UART_CLK_EN |
#endif
#if CONFIG_ESP_CONSOLE_UART_NUM != 1
                           DPORT_UART1_CLK_EN |
#endif
                           DPORT_USB_CLK_EN |
                           DPORT_SPI2_CLK_EN |
                           DPORT_I2C_EXT0_CLK_EN |
                           DPORT_UHCI0_CLK_EN |
                           DPORT_RMT_CLK_EN |
                           DPORT_PCNT_CLK_EN |
                           DPORT_LEDC_CLK_EN |
                           DPORT_TIMERGROUP1_CLK_EN |
                           DPORT_SPI3_CLK_EN |
                           DPORT_SPI4_CLK_EN |
                           DPORT_PWM0_CLK_EN |
                           DPORT_CAN_CLK_EN |
                           DPORT_PWM1_CLK_EN |
                           DPORT_I2S1_CLK_EN |
                           DPORT_SPI2_DMA_CLK_EN |
                           DPORT_SPI3_DMA_CLK_EN |
                           DPORT_PWM2_CLK_EN |
                           DPORT_PWM3_CLK_EN;
        common_perip_clk1 = 0;
        hwcrypto_perip_clk = DPORT_CRYPTO_AES_CLK_EN |
                             DPORT_CRYPTO_SHA_CLK_EN |
                             DPORT_CRYPTO_RSA_CLK_EN;
        wifi_bt_sdio_clk = DPORT_WIFI_CLK_WIFI_EN |
                           DPORT_WIFI_CLK_BT_EN_M |
                           DPORT_WIFI_CLK_UNUSED_BIT5 |
                           DPORT_WIFI_CLK_UNUSED_BIT12 |
                           DPORT_WIFI_CLK_SDIOSLAVE_EN |
                           DPORT_WIFI_CLK_SDIO_HOST_EN |
                           DPORT_WIFI_CLK_EMAC_EN;
    }

    //Reset the communication peripherals like I2C, SPI, UART, I2S and bring them to known state.
    common_perip_clk |= DPORT_I2S0_CLK_EN |
#if CONFIG_ESP_CONSOLE_UART_NUM != 0
                        DPORT_UART_CLK_EN |
#endif
#if CONFIG_ESP_CONSOLE_UART_NUM != 1
                        DPORT_UART1_CLK_EN |
#endif
                        DPORT_USB_CLK_EN |
                        DPORT_SPI2_CLK_EN |
                        DPORT_I2C_EXT0_CLK_EN |
                        DPORT_UHCI0_CLK_EN |
                        DPORT_RMT_CLK_EN |
                        DPORT_UHCI1_CLK_EN |
                        DPORT_SPI3_CLK_EN |
                        DPORT_SPI4_CLK_EN |
                        DPORT_I2C_EXT1_CLK_EN |
                        DPORT_I2S1_CLK_EN |
                        DPORT_SPI2_DMA_CLK_EN |
                        DPORT_SPI3_DMA_CLK_EN;
    common_perip_clk1 = 0;

    /* Change I2S clock to audio PLL first. Because if I2S uses 160MHz clock,
     * the current is not reduced when disable I2S clock.
     */
    REG_SET_FIELD(I2S_CLKM_CONF_REG(0), I2S_CLK_SEL, I2S_CLK_AUDIO_PLL);
    REG_SET_FIELD(I2S_CLKM_CONF_REG(1), I2S_CLK_SEL, I2S_CLK_AUDIO_PLL);

    /* Disable some peripheral clocks. */
    DPORT_CLEAR_PERI_REG_MASK(DPORT_PERIP_CLK_EN_REG, common_perip_clk);
    DPORT_SET_PERI_REG_MASK(DPORT_PERIP_RST_EN_REG, common_perip_clk);

    DPORT_CLEAR_PERI_REG_MASK(DPORT_PERIP_CLK_EN1_REG, common_perip_clk1);
    DPORT_SET_PERI_REG_MASK(DPORT_PERIP_RST_EN1_REG, common_perip_clk1);

    /* Disable hardware crypto clocks. */
    DPORT_CLEAR_PERI_REG_MASK(DPORT_PERI_CLK_EN_REG, hwcrypto_perip_clk);
    DPORT_SET_PERI_REG_MASK(DPORT_PERI_RST_EN_REG, hwcrypto_perip_clk);

    /* Disable WiFi/BT/SDIO clocks. */
    DPORT_CLEAR_PERI_REG_MASK(DPORT_WIFI_CLK_EN_REG, wifi_bt_sdio_clk);

    /* Enable WiFi MAC and POWER clocks */
    DPORT_SET_PERI_REG_MASK(DPORT_WIFI_CLK_EN_REG, DPORT_WIFI_CLK_WIFI_EN);

    /* Enable RNG clock. */
    periph_module_enable(PERIPH_RNG_MODULE);
}