147 lines
2.7 KiB
INI
147 lines
2.7 KiB
INI
[stepper_y]
|
|
#Motor B
|
|
step_pin: PD8
|
|
dir_pin: PB12
|
|
enable_pin: !PD9
|
|
rotation_distance: 40
|
|
microsteps: 16
|
|
full_steps_per_rotation:200
|
|
endstop_pin: ^PB13
|
|
position_min: 0
|
|
|
|
position_endstop: 350
|
|
position_max: 350
|
|
|
|
homing_speed: 150
|
|
homing_retract_dist: 5
|
|
homing_positive_dir: true
|
|
|
|
[tmc2209 stepper_y]
|
|
uart_pin: PE15
|
|
interpolate: True
|
|
run_current: 1.0
|
|
#hold_current: 0.5
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
#######################################
|
|
|
|
[stepper_x]
|
|
#Motor A
|
|
step_pin: PE11
|
|
dir_pin: PE10
|
|
enable_pin: !PE9
|
|
rotation_distance: 40
|
|
microsteps: 16
|
|
full_steps_per_rotation:200 #set to 400 for 0.9 degree stepper
|
|
endstop_pin: ^PB14
|
|
position_min: 0
|
|
|
|
position_endstop: 350
|
|
position_max: 350
|
|
|
|
homing_speed: 150
|
|
homing_retract_dist: 5
|
|
homing_positive_dir: true
|
|
|
|
[tmc2209 stepper_x]
|
|
uart_pin: PE7
|
|
interpolate: True
|
|
run_current: 1.0
|
|
#hold_current: 0.5
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
#######################################
|
|
|
|
## In Z-MOT Position
|
|
## Z0 Stepper - Front Left
|
|
[stepper_z]
|
|
step_pin: PE6
|
|
dir_pin: !PC13
|
|
enable_pin: !PE5
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 16
|
|
## In Z- Position
|
|
#endstop_pin: PA3 ; Z Endstop
|
|
endstop_pin: probe:z_virtual_endstop
|
|
## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0)
|
|
## (+) value = endstop above Z0, (-) value = endstop below
|
|
## Increasing position_endstop brings nozzle closer to the bed
|
|
## After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config
|
|
#position_endstop: 0.350
|
|
position_max: 350
|
|
position_min: 0
|
|
homing_speed: 10
|
|
second_homing_speed: 3
|
|
homing_retract_dist: 2
|
|
|
|
[tmc2209 stepper_z]
|
|
uart_pin: PC14
|
|
uart_address: 0
|
|
interpolate: False
|
|
run_current: 0.8
|
|
#hold_current: 0.5
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
#######################################
|
|
|
|
## In E1-MOT Position
|
|
## Z1 Stepper - Rear Left
|
|
[stepper_z1]
|
|
step_pin: PD12
|
|
dir_pin: PC4
|
|
enable_pin: !PE8
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 16
|
|
|
|
[tmc2209 stepper_z1]
|
|
uart_pin: PA15
|
|
interpolate: False
|
|
run_current: 0.8
|
|
#hold_current: 0.5
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
#######################################
|
|
|
|
## In E2-MOT Position
|
|
## Z2 Stepper - Rear Right
|
|
[stepper_z2]
|
|
step_pin: PE1
|
|
dir_pin: !PE0
|
|
enable_pin: !PC5
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 16
|
|
|
|
[tmc2209 stepper_z2]
|
|
uart_pin: PD11
|
|
interpolate: False
|
|
run_current: 0.8
|
|
#hold_current: 0.5
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
#######################################
|
|
|
|
## In E3-MOT Position
|
|
## Z3 Stepper - Front Right
|
|
[stepper_z3]
|
|
step_pin: PE2
|
|
dir_pin: PE4
|
|
enable_pin: !PE3
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 16
|
|
|
|
[tmc2209 stepper_z3]
|
|
uart_pin: PC15
|
|
interpolate: False
|
|
run_current: 0.8
|
|
#hold_current: 0.5
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0 |