82 lines
No EOL
1.7 KiB
INI
82 lines
No EOL
1.7 KiB
INI
#[probe]
|
|
#pin: ^!PA0
|
|
#x_offset: 0
|
|
#y_offset: 25.0
|
|
#z_offset: 7.8
|
|
#speed: 25.0
|
|
#samples: 3
|
|
#samples_result: median
|
|
#sample_retract_dist: 4.0
|
|
#samples_tolerance: 0.025
|
|
#samples_tolerance_retries: 3
|
|
|
|
[bltouch]
|
|
sensor_pin: PA0
|
|
control_pin: PA2
|
|
x_offset: 0
|
|
y_offset: 25.0
|
|
z_offset: 3.155
|
|
speed: 10.0
|
|
samples: 3
|
|
samples_result: median
|
|
sample_retract_dist: 3.0
|
|
samples_tolerance: 0.015
|
|
samples_tolerance_retries: 3
|
|
|
|
[extruder]
|
|
step_pin: PD5
|
|
dir_pin: PD6
|
|
enable_pin: !PD4
|
|
|
|
## Update value below when you perform extruder calibration
|
|
## If you ask for 100mm of filament, but in reality it is 98mm:
|
|
## rotation_distance = <previous_rotation_distance> * <actual_extrude_distance> / 100
|
|
## 22.6789511 is a good starting point
|
|
rotation_distance: 23.1325301 #Bondtech 5mm Drive Gears
|
|
## Update Gear Ratio depending on your Extruder Type
|
|
## Use 50:17 for Afterburner/Clockwork (BMG Gear Ratio)
|
|
## Use 80:20 for M4, M3.1
|
|
gear_ratio: 50:17 #BMG Gear Ratio
|
|
microsteps: 16
|
|
|
|
full_steps_per_rotation: 200 #200 for 1.8 degree, 400 for 0.9 degree
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.75
|
|
heater_pin: PB15
|
|
sensor_type: ATC Semitec 104GT-2
|
|
sensor_pin: PC0
|
|
min_temp: 10
|
|
max_temp: 300
|
|
max_power: 1.0
|
|
min_extrude_temp: 210
|
|
control = pid
|
|
pid_kp = 28.020
|
|
pid_ki = 1.746
|
|
pid_kd = 112.429
|
|
pressure_advance: 0.05
|
|
pressure_advance_smooth_time: 0.040
|
|
max_extrude_only_distance: 200
|
|
max_extrude_cross_section: 50.0
|
|
|
|
[tmc2209 extruder]
|
|
uart_pin: PD7
|
|
interpolate: false
|
|
run_current: 0.5
|
|
#hold_current: 0.2
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
[heater_fan hotend_fan]
|
|
pin: PB1
|
|
max_power: 1.0
|
|
fan_speed: 1.0
|
|
kick_start_time: 0.5
|
|
heater: extruder
|
|
heater_temp: 50.0
|
|
shutdown_speed: 1.0
|
|
|
|
[fan]
|
|
pin: PB0
|
|
max_power: 1.0
|
|
kick_start_time: 0.5
|
|
off_below: 0.2 |