2022-10-01 17:20:40 +00:00
|
|
|
[virtual_sdcard]
|
2022-10-27 11:57:14 +00:00
|
|
|
path: /home/klipper/printer_data/gcodes
|
2022-10-01 17:20:40 +00:00
|
|
|
|
|
|
|
|
[display_status]
|
|
|
|
|
|
|
|
|
|
[pause_resume]
|
|
|
|
|
recover_velocity: 300.0
|
|
|
|
|
|
|
|
|
|
[printer]
|
|
|
|
|
kinematics: corexy
|
|
|
|
|
max_velocity: 300
|
|
|
|
|
max_accel: 3000 #Max 4000
|
|
|
|
|
max_z_velocity: 20 #Max 15 for 12V TMC Drivers, can increase for 24V
|
|
|
|
|
max_z_accel: 300
|
|
|
|
|
square_corner_velocity: 5.0
|
|
|
|
|
|
|
|
|
|
[mcu] ;Spider Board 1
|
|
|
|
|
restart_method: command
|
|
|
|
|
serial: /dev/ttyAMA0
|
|
|
|
|
|
|
|
|
|
[controller_fan Electronics_Fan1]
|
|
|
|
|
pin: PB2
|
|
|
|
|
max_power: 1.0
|
|
|
|
|
fan_speed: 1.0
|
|
|
|
|
kick_start_time: 0.5
|
|
|
|
|
idle_timeout: 180
|
|
|
|
|
idle_speed: 1.0
|
|
|
|
|
heater: extruder
|
|
|
|
|
stepper: stepper_x,stepper_y,stepper_z,stepper_z1,stepper_z2,stepper_z3
|
|
|
|
|
shutdown_speed: 1.0
|
|
|
|
|
|
|
|
|
|
[include config/mcu_rpi.cfg]
|
|
|
|
|
[include config/mcu_mcu2.cfg]
|
|
|
|
|
[include config/stepper.cfg]
|
|
|
|
|
[include config/extruder_hotend.cfg]
|
|
|
|
|
[include config/heated_bed.cfg]
|
|
|
|
|
[include config/macros.cfg]
|
|
|
|
|
[include config/timelapse.cfg]
|
|
|
|
|
[include config/ercf/ercf_hardware.cfg]
|
|
|
|
|
[include config/ercf/ercf_software.cfg]
|
|
|
|
|
|
|
|
|
|
[idle_timeout]
|
|
|
|
|
timeout: 1800
|
|
|
|
|
|
|
|
|
|
#*# <---------------------- SAVE_CONFIG ---------------------->
|
|
|
|
|
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
|
|
|
|
#*#
|
|
|
|
|
#*# [input_shaper]
|
|
|
|
|
#*# shaper_type_x = mzv
|
|
|
|
|
#*# shaper_freq_x = 64.0
|
|
|
|
|
#*# shaper_type_y = mzv
|
|
|
|
|
#*# shaper_freq_y = 37.6
|
