OVMS3/OVMS.V3/components/vehicle_mitsubishi/docs/index.rst

156 lines
6.5 KiB
ReStructuredText

===============
Mitsubishi Trio
===============
Vehicle Type: **MI**
This should be used to support the Mitsubishi i-Miev (Citroen C-Zero, Peugeot iOn) vehicles.
----------------
Support Overview
----------------
=========================== ==============
Function Support Status
=========================== ==============
Hardware Any OVMS v3 (or later) module
Vehicle Cable OBD-II to DB9 Data Cable for OVMS (1441200 right, or 1139300 left)
GSM Antenna 1000500 Open Vehicles OVMS GSM Antenna (or any compatible antenna)
GPS Antenna 1020200 Universal GPS Antenna (SMA Connector) (or any compatible antenna)
SOC Display Yes
Range Display Yes
GPS Location Yes
Speed Display Yes
Temperature Display No
BMS v+t Display Yes
TPMS Display Not currently supported
Charge Status Display Yes
Charge Interruption Alerts Yes
Charge Control No
Cabin Pre-heat/cool Control Not currently supported
Lock/Unlock Vehicle Not currently supported
Valet Mode Control Not currently supported
Others
=========================== ==============
---------------------
Trio specific metrics
---------------------
NB! Not all metrics are correct or tested properly. This is a work in progress.
==================================== ==================
Metric Description
==================================== ==================
xmi.b.power.min The battery minimum power usage
xmi.b.power.max The battery maximum power usage
xmi.e.lowbeam Low beam light status
xmi.e.highbeam High beam light status
xmi.e.frontfog Front fog light status
xmi.e.rearfog Rear fog light status
xmi.e.rightblinker Right blinker status
xmi.e.leftblinker Left blinker status
xmi.e.warninglight Warning light status
xmi.c.kwh.dc Charge energy on DC side in kWh
xmi.c.kwh.ac Charge energy on AC side in kWh
xmi.c.efficiency Charge efficiency (DC/AC)
xmi.c.power.ac Charge power on AC side in kW
xmi.c.power.dc Charge power on DC side in kW
xmi.c.time Charge time (h:mm.ss)
xmi.c.soc.start Charge start soc in %
xmi.c.soc.stop Charge stop soc in %
xmi.e.heating.amp Heating energy usage in A
xmi.e.heating.watt Heating energy usage in W
xmi.e.heating.temp.return Heater return water temperature
xmi.e.heating.temp.flow Heater flow water temperature
xmi.e.ac.amp AC energy usage in A
xmi.e.ac.watt AC energy usage in W
xmi.e.trip.park Trip start odometer in km
xmi.e.trip.park.energy.used Energy used in kWh
xmi.e.trip.park.energy.recuperated Recuperated energy in kWh
xmi.e.trip.park.heating.kwh Heater energy usage on trip in kWh
xmi.e.trip.park.ac.kwh AC energy usage on trip in kWh
xmi.e.trip.park.soc.start Trip start soc
xmi.e.trip.park.soc.stop Trip stop soc
xmi.e.trip.charge Trip start odometer in km since charge
xmi.e.trip.charge.energy.used Energy used in kWh since charge
xmi.e.trip.charge.energy.recuperated Recupe.. energy in kWh since charge
xmi.e.trip.charge.heating.kwh Heating usage in kWh since charge
xmi.e.trip.charge.ac.kwh AC energy usage in kWh since charge
xmi.e.trip.charge.soc.start Trip start soc since charge
xmi.e.trip.charge.soc.stop Trip stop soc since charge
==================================== ==================
Note that some metrics are polled at different rates than others and some metrics are not available when car is off. This means that after a restart of the OVMS, some metrics will be missing until the car is turned on and maybe driven for few minutes.
---------------
Custom Commands
---------------
^^^^^^^^^^^^^^^^^^
Read only commands
^^^^^^^^^^^^^^^^^^
| ``xmi trip``
| Returns info about the last trip, from you start the car with key.
| ``xmi tripc``
| Returns info about the trip since last charge.
| ``xmi aux``
| Prints out the voltage level of the auxiliary battery.
| ``xmi vin``
| Prints out some more information taken from the cars VIN-number.
---------------------------
Trio Regen Brake Light Hack
---------------------------
^^^^^^^^^^^^^^
Parts required
^^^^^^^^^^^^^^
* 1x DA26 / Sub-D 26HD Plug & housing
* Note: housings for Sub-D 15 fit for 26HD
* e.g. Assmann-WSW-A-HDS-26-LL-Z
* Encitech-DPPK15-BK-K-D-SUB-Gehaeuse
* 1x 12V Universal Car Relay + Socket
* e.g. Song-Chuan-896H-1CH-C1-12V-DC-Kfz-Relais
* GoodSky-Relaissockel-1-St.-GRL-CS3770
* 1x 1 Channel 12V Relay Module With Optocoupler Isolation
* 12V 1 channel relay module with Optocoupler Isolation
Car wire-tap connectors, car crimp connectors, 0.5 mm² wires, zipties, shrink-on tube, tools
Note: if you already use the switched 12V output of the OVMS for something different, you can use one of the free EGPIO outputs. That requires additionally routing an EGPIO line to the DA26 connector at the expansion slot (e.g. using a jumper) and using a relay module (2/b: relay shield) with separate power input instead of the standard car relay.
I use 2/b (relay shield) variant: Be aware the MAX71317 outputs are open drain, so you need a pull up resistor to e.g. +3.3. According to the data sheet, the current should stay below 6 mA.
Inside OVMS Box: Connect JP1 Pin10 (GEP7) to Pin12 (EGPIO_8) with jumper
In DA26 connector::
pin 24(+3.3) ----- [ 680 Ohms ] ---+--- [ Relay board IN ]
|
pin 21 (EGPIO_8)
pin 9 ----- [Relay board DC+]
pin 8 ----- [Relay board DC-]
[Relay board COM] ----- Brake pedal switch one side
[Relay board NO] ----- Brake pedal switch other side
^^^^^^^^^^^^^
Configuration
^^^^^^^^^^^^^
See OVMS web user interface, menu Trio → Brake Light:
.. image:: trio1.png
Set the port as necessary and the checkbox to enable the brakelight.
For monitoring and fine tuning, use the „regenmon“ web plugin:
https://github.com/openvehicles/Open-Vehicle-Monitoring-System-3/blob/master/vehicle/OVMS.V3/components/ovms_webserver/dev/regenmon.htm
.. image:: trio2.png