unused variable 'lfn' 'isr_handler' defined but not used 'servo_set_angle' defined but not used 'gpio_test_signal' defined but not used 'change_duty' defined but not used
78 lines
No EOL
2.8 KiB
C
78 lines
No EOL
2.8 KiB
C
/* servo motor control example
|
|
|
|
This example code is in the Public Domain (or CC0 licensed, at your option.)
|
|
|
|
Unless required by applicable law or agreed to in writing, this
|
|
software is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR
|
|
CONDITIONS OF ANY KIND, either express or implied.
|
|
*/
|
|
#include <stdio.h>
|
|
|
|
#include "freertos/FreeRTOS.h"
|
|
#include "freertos/task.h"
|
|
#include "esp_attr.h"
|
|
|
|
#include "driver/mcpwm.h"
|
|
#include "soc/mcpwm_reg.h"
|
|
#include "soc/mcpwm_struct.h"
|
|
|
|
//You can get these value from the datasheet of servo you use, in general pulse width varies between 1000 to 2000 mocrosecond
|
|
#define SERVO_MIN_PULSEWIDTH 1000 //Minimum pulse width in microsecond
|
|
#define SERVO_MAX_PULSEWIDTH 2000 //Maximum pulse width in microsecond
|
|
#define SERVO_MAX_DEGREE 90 //Maximum angle in degree upto which servo can rotate
|
|
|
|
static void mcpwm_example_gpio_initialize()
|
|
{
|
|
printf("initializing mcpwm servo control gpio......\n");
|
|
mcpwm_gpio_init(MCPWM_UNIT_0, MCPWM0A, 18); //Set GPIO 18 as PWM0A, to which servo is connected
|
|
}
|
|
|
|
/**
|
|
* @brief Use this function to calcute pulse width for per degree rotation
|
|
*
|
|
* @param degree_of_rotation the angle in degree to which servo has to rotate
|
|
*
|
|
* @return
|
|
* - calculated pulse width
|
|
*/
|
|
static uint32_t servo_per_degree_init(uint32_t degree_of_rotation)
|
|
{
|
|
uint32_t cal_pulsewidth = 0;
|
|
cal_pulsewidth = (SERVO_MIN_PULSEWIDTH + (((SERVO_MAX_PULSEWIDTH - SERVO_MIN_PULSEWIDTH) * (degree_of_rotation)) / (SERVO_MAX_DEGREE)));
|
|
return cal_pulsewidth;
|
|
}
|
|
|
|
/**
|
|
* @brief Configure MCPWM module
|
|
*/
|
|
void mcpwm_example_servo_control(void *arg)
|
|
{
|
|
uint32_t angle, count;
|
|
//1. mcpwm gpio initialization
|
|
mcpwm_example_gpio_initialize();
|
|
|
|
//2. initial mcpwm configuration
|
|
printf("Configuring Initial Parameters of mcpwm......\n");
|
|
mcpwm_config_t pwm_config;
|
|
pwm_config.frequency = 50; //frequency = 50Hz, i.e. for every servo motor time period should be 20ms
|
|
pwm_config.cmpr_a = 0; //duty cycle of PWMxA = 0
|
|
pwm_config.cmpr_b = 0; //duty cycle of PWMxb = 0
|
|
pwm_config.counter_mode = MCPWM_UP_COUNTER;
|
|
pwm_config.duty_mode = MCPWM_DUTY_MODE_0;
|
|
mcpwm_init(MCPWM_UNIT_0, MCPWM_TIMER_0, &pwm_config); //Configure PWM0A & PWM0B with above settings
|
|
while (1) {
|
|
for (count = 0; count < SERVO_MAX_DEGREE; count++) {
|
|
printf("Angle of rotation: %d\n", count);
|
|
angle = servo_per_degree_init(count);
|
|
printf("pulse width: %dus\n", angle);
|
|
mcpwm_set_duty_in_us(MCPWM_UNIT_0, MCPWM_TIMER_0, MCPWM_OPR_A, angle);
|
|
vTaskDelay(10); //Add delay, since it takes time for servo to rotate, generally 100ms/60degree rotation at 5V
|
|
}
|
|
}
|
|
}
|
|
|
|
void app_main()
|
|
{
|
|
printf("Testing servo motor.......\n");
|
|
xTaskCreate(mcpwm_example_servo_control, "mcpwm_example_servo_control", 4096, NULL, 5, NULL);
|
|
} |