OVMS3-idf/components/ethernet/eth_phy/phy_common.c
morris 18cb87b4ce ethernet: support new PHY (IP101)
1. Add support for new PHY IP101.
2. Re-enable GPIO0 output mode.
3. Clean up some docs.
2019-01-31 15:02:45 +08:00

80 lines
2.7 KiB
C

// Copyright 2015-2016 Espressif Systems (Shanghai) PTE LTD
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
// http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
#include "eth_phy/phy.h"
#include "eth_phy/phy_reg.h"
#include "driver/gpio.h"
#include "esp_log.h"
static const char *TAG = "phy_common";
void phy_rmii_configure_data_interface_pins(void)
{
// CRS_DRV to GPIO27
PIN_FUNC_SELECT(PERIPHS_IO_MUX_GPIO27_U, FUNC_GPIO27_EMAC_RX_DV);
// TXD0 to GPIO19
PIN_FUNC_SELECT(PERIPHS_IO_MUX_GPIO19_U, FUNC_GPIO19_EMAC_TXD0);
// TX_EN to GPIO21
PIN_FUNC_SELECT(PERIPHS_IO_MUX_GPIO21_U, FUNC_GPIO21_EMAC_TX_EN);
// TXD1 to GPIO22
PIN_FUNC_SELECT(PERIPHS_IO_MUX_GPIO22_U, FUNC_GPIO22_EMAC_TXD1);
// RXD0 to GPIO25
gpio_set_direction(25, GPIO_MODE_INPUT);
// RXD1 to GPIO26
gpio_set_direction(26, GPIO_MODE_INPUT);
// RMII CLK to GPIO0
gpio_set_direction(0, GPIO_MODE_INPUT);
}
void phy_rmii_smi_configure_pins(uint8_t mdc_gpio, uint8_t mdio_gpio)
{
// setup SMI MDC pin
gpio_set_direction(mdc_gpio, GPIO_MODE_OUTPUT);
gpio_matrix_out(mdc_gpio, EMAC_MDC_O_IDX, 0, 0);
PIN_FUNC_SELECT(GPIO_PIN_MUX_REG[mdc_gpio], PIN_FUNC_GPIO);
// setup SMI MDIO pin
gpio_set_direction(mdio_gpio, GPIO_MODE_INPUT_OUTPUT);
gpio_matrix_out(mdio_gpio, EMAC_MDO_O_IDX, 0, 0);
gpio_matrix_in(mdio_gpio, EMAC_MDI_I_IDX, 0);
PIN_FUNC_SELECT(GPIO_PIN_MUX_REG[mdio_gpio], PIN_FUNC_GPIO);
}
void phy_mii_enable_flow_ctrl(void)
{
uint32_t data = esp_eth_smi_read(MII_AUTO_NEG_ADVERTISEMENT_REG);
data |= MII_ASM_DIR | MII_PAUSE;
esp_eth_smi_write(MII_AUTO_NEG_ADVERTISEMENT_REG, data);
}
bool phy_mii_check_link_status(void)
{
if ((esp_eth_smi_read(MII_BASIC_MODE_STATUS_REG) & MII_LINK_STATUS)) {
ESP_LOGD(TAG, "phy_mii_check_link_status(UP)");
return true;
} else {
ESP_LOGD(TAG, "phy_mii_check_link_status(DOWN)");
return false;
}
}
bool phy_mii_get_partner_pause_enable(void)
{
if ((esp_eth_smi_read(MII_PHY_LINK_PARTNER_ABILITY_REG) & MII_PARTNER_PAUSE)) {
ESP_LOGD(TAG, "phy_mii_get_partner_pause_enable(TRUE)");
return true;
} else {
ESP_LOGD(TAG, "phy_mii_get_partner_pause_enable(FALSE)");
return false;
}
}