OVMS3-idf/components/soc/include/hal/spi_flash_hal.h
Renz Christian Bagaporo e6ad330018 ble_mesh_wifi_coexist example: Disable Wi-Fi RX IRAM optimisation
Otherwise IRAM usage is too high in this example.
2019-11-28 09:20:00 +08:00

218 lines
8 KiB
C
Raw Blame History

This file contains ambiguous Unicode characters

This file contains Unicode characters that might be confused with other characters. If you think that this is intentional, you can safely ignore this warning. Use the Escape button to reveal them.

// Copyright 2010-2019 Espressif Systems (Shanghai) PTE LTD
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
//
// http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
/*******************************************************************************
* NOTICE
* The HAL is not public api, don't use in application code.
* See readme.md in soc/include/hal/readme.md
******************************************************************************/
// The HAL layer for SPI Flash (common part)
#pragma once
#include "hal/spi_flash_ll.h"
#include "hal/spi_types.h"
#include "hal/spi_flash_types.h"
#include "soc/soc_memory_layout.h"
/* Hardware host-specific constants */
#define SPI_FLASH_HAL_MAX_WRITE_BYTES 64
#define SPI_FLASH_HAL_MAX_READ_BYTES 64
/**
* Generic driver context structure for all chips using the SPI peripheral.
* Include this into the HEAD of the driver data for other driver
* implementations that also use the SPI peripheral.
*/
typedef struct {
spi_dev_t *spi; ///< Pointer to SPI peripheral registers (SP1, SPI2 or SPI3). Set before initialisation.
int cs_num; ///< Which cs pin is used, 0-2.
int extra_dummy;
spi_flash_ll_clock_reg_t clock_conf;
} spi_flash_memspi_data_t;
/// Configuration structure for the SPI driver.
typedef struct {
spi_host_device_t host_id; ///< SPI peripheral ID.
int cs_num; ///< Which cs pin is used, 0-2.
bool iomux; ///< Whether the IOMUX is used, used for timing compensation.
int input_delay_ns; ///< Input delay on the MISO pin after the launch clock used for timing compensation.
esp_flash_speed_t speed;///< SPI flash clock speed to work at.
} spi_flash_memspi_config_t;
/**
* Configure SPI flash hal settings.
*
* @param data Buffer to hold configured data, the buffer should be in DRAM to be available when cache disabled
* @param cfg Configurations to set
*
* @return
* - ESP_OK: success
* - ESP_ERR_INVALID_ARG: the data buffer is not in the DRAM.
*/
esp_err_t spi_flash_hal_init(spi_flash_memspi_data_t *data_out, const spi_flash_memspi_config_t *cfg);
/**
* Configure the device-related register before transactions.
*
* @param driver The driver context.
*
* @return always return ESP_OK.
*/
esp_err_t spi_flash_hal_device_config(spi_flash_host_driver_t *driver);
/**
* Send an user-defined spi transaction to the device.
*
* @note This is usually used when the memspi interface doesn't support some
* particular commands. Since this function supports timing compensation, it is
* also used to receive some data when the frequency is high.
*
* @param driver The driver context.
* @param trans The transaction to send, also holds the received data.
*
* @return always return ESP_OK.
*/
esp_err_t spi_flash_hal_common_command(spi_flash_host_driver_t *driver, spi_flash_trans_t *trans);
/**
* Erase whole flash chip by using the erase chip (C7h) command.
*
* @param driver The driver context.
*/
void spi_flash_hal_erase_chip(spi_flash_host_driver_t *driver);
/**
* Erase a specific sector by its start address through the sector erase (20h)
* command.
*
* @param driver The driver context.
* @param start_address Start address of the sector to erase.
*/
void spi_flash_hal_erase_sector(spi_flash_host_driver_t *driver, uint32_t start_address);
/**
* Erase a specific 64KB block by its start address through the 64KB block
* erase (D8h) command.
*
* @param driver The driver context.
* @param start_address Start address of the block to erase.
*/
void spi_flash_hal_erase_block(spi_flash_host_driver_t *driver, uint32_t start_address);
/**
* Program a page of the flash using the page program (02h) command.
*
* @param driver The driver context.
* @param address Address of the page to program
* @param buffer Data to program
* @param length Size of the buffer in bytes, no larger than ``SPI_FLASH_HAL_MAX_WRITE_BYTES`` (64) bytes.
*/
void spi_flash_hal_program_page(spi_flash_host_driver_t *driver, const void *buffer, uint32_t address, uint32_t length);
/**
* Read from the flash. Call ``spi_flash_hal_configure_host_read_mode`` to
* configure the read command before calling this function.
*
* @param driver The driver context.
* @param buffer Buffer to store the read data
* @param address Address to read
* @param length Length to read, no larger than ``SPI_FLASH_HAL_MAX_READ_BYTES`` (64) bytes.
*
* @return always return ESP_OK.
*/
esp_err_t spi_flash_hal_read(spi_flash_host_driver_t *driver, void *buffer, uint32_t address, uint32_t read_len);
/**
* @brief Send the write enable (06h) or write disable (04h) command to the flash chip.
*
* @param driver The driver context.
* @param wp true to enable the write protection, otherwise false.
*
* @return always return ESP_OK.
*/
esp_err_t spi_flash_hal_set_write_protect(spi_flash_host_driver_t *chip_drv, bool wp);
/**
* Check whether the SPI host is idle and can perform other operations.
*
* @param driver The driver context.
*
* @return ture if idle, otherwise false.
*/
bool spi_flash_hal_host_idle(spi_flash_host_driver_t *driver);
/**
* @brief Configure the SPI host hardware registers for the specified io mode.
*
* Note that calling this configures SPI host registers, so if running any
* other commands as part of set_io_mode() then these must be run before
* calling this function.
*
* The command value, address length and dummy cycles are configured according
* to the format of read commands:
*
* - command: 8 bits, value set.
* - address: 24 bits
* - dummy: cycles to compensate the input delay
* - out & in data: 0 bits.
*
* The following commands still need to:
*
* - Read data: set address value and data (length and contents), no need
* to touch command and dummy phases.
* - Common read: set command value, address value (or length to 0 if not used)
* - Common write: set command value, address value (or length to 0 if not
* used), disable dummy phase, and set output data.
*
* @param driver The driver context
* @param io_mode The HW read mode to use
* @param addr_bitlen Length of the address phase, in bits
* @param dummy_cyclelen_base Base cycles of the dummy phase, some extra dummy cycles may be appended to compensate the timing.
* @param command Actual reading command to send to flash chip on the bus.
*
* @return always return ESP_OK.
*/
esp_err_t spi_flash_hal_configure_host_io_mode(spi_flash_host_driver_t *driver, uint32_t command, uint32_t addr_bitlen,
int dummy_cyclelen_base, esp_flash_io_mode_t io_mode);
/**
* Poll until the last operation is done.
*
* @param driver The driver context.
*/
void spi_flash_hal_poll_cmd_done(spi_flash_host_driver_t *driver);
/**
* Check whether the given buffer can be used as the write buffer directly. If 'chip' is connected to the main SPI bus, we can only write directly from
* regions that are accessible ith cache disabled. *
*
* @param driver The driver context
* @param p The buffer holding data to send.
*
* @return True if the buffer can be used to send data, otherwise false.
*/
bool spi_flash_hal_supports_direct_write(spi_flash_host_driver_t *driver, const void *p);
/**
* Check whether the given buffer can be used as the read buffer directly. If 'chip' is connected to the main SPI bus, we can only read directly from
* regions that are accessible ith cache disabled. *
*
* @param driver The driver context
* @param p The buffer to hold the received data.
*
* @return True if the buffer can be used to receive data, otherwise false.
*/
bool spi_flash_hal_supports_direct_read(spi_flash_host_driver_t *driver, const void *p);