- RTC_CNTL_SLOWCLK_FREQ define is removed; rtc_clk_slow_freq_get_hz function can be used instead to get an approximate RTC_SLOW_CLK frequency - Clock calibration is performed at startup. The value is saved and used for timekeeping and when entering deep sleep. - When using the 32k XTAL, startup code will wait for the oscillator to start up. This can be possibly optimized by starting a separate task to wait for oscillator startup, and performing clock switch in that task. - Fix a bug that 32k XTAL would be disabled in rtc_clk_init. - Fix a rounding error in rtc_clk_cal, which caused systematic frequency error. - Fix an overflow bug which caused rtc_clk_cal to timeout early if the slow_clk_cycles argument would exceed certain value - Improve 32k XTAL oscillator startup time by introducing bootstrapping code, which uses internal pullup/pulldown resistors on 32K_N/32K_P pins to set better initial conditions for the oscillator.
460 lines
17 KiB
C
460 lines
17 KiB
C
// Copyright 2010-2016 Espressif Systems (Shanghai) PTE LTD
|
|
//
|
|
// Licensed under the Apache License, Version 2.0 (the "License");
|
|
// you may not use this file except in compliance with the License.
|
|
// You may obtain a copy of the License at
|
|
//
|
|
// http://www.apache.org/licenses/LICENSE-2.0
|
|
//
|
|
// Unless required by applicable law or agreed to in writing, software
|
|
// distributed under the License is distributed on an "AS IS" BASIS,
|
|
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
// See the License for the specific language governing permissions and
|
|
// limitations under the License.
|
|
|
|
#include <stdio.h>
|
|
#include <string.h>
|
|
#include <freertos/FreeRTOS.h>
|
|
#include <freertos/task.h>
|
|
#include <freertos/semphr.h>
|
|
|
|
#include <unity.h>
|
|
#include "esp_attr.h"
|
|
#include "esp_err.h"
|
|
#include "esp_log.h"
|
|
#include "esp_deep_sleep.h"
|
|
|
|
#include "esp32/ulp.h"
|
|
|
|
#include "soc/soc.h"
|
|
#include "soc/rtc.h"
|
|
#include "soc/rtc_cntl_reg.h"
|
|
#include "soc/sens_reg.h"
|
|
#include "driver/rtc_io.h"
|
|
|
|
#include "sdkconfig.h"
|
|
|
|
static void hexdump(const uint32_t* src, size_t count) {
|
|
for (size_t i = 0; i < count; ++i) {
|
|
printf("%08x ", *src);
|
|
++src;
|
|
if ((i + 1) % 4 == 0) {
|
|
printf("\n");
|
|
}
|
|
}
|
|
}
|
|
|
|
TEST_CASE("ulp add test", "[ulp]")
|
|
{
|
|
memset(RTC_SLOW_MEM, 0, CONFIG_ULP_COPROC_RESERVE_MEM);
|
|
const ulp_insn_t program[] = {
|
|
I_MOVI(R3, 16),
|
|
I_LD(R0, R3, 0),
|
|
I_LD(R1, R3, 1),
|
|
I_ADDR(R2, R0, R1),
|
|
I_ST(R2, R3, 2),
|
|
I_HALT()
|
|
};
|
|
RTC_SLOW_MEM[16] = 10;
|
|
RTC_SLOW_MEM[17] = 11;
|
|
size_t size = sizeof(program)/sizeof(ulp_insn_t);
|
|
TEST_ASSERT_EQUAL(ESP_OK, ulp_process_macros_and_load(0, program, &size));
|
|
TEST_ASSERT_EQUAL(ESP_OK, ulp_run(0));
|
|
ets_delay_us(1000);
|
|
hexdump(RTC_SLOW_MEM, CONFIG_ULP_COPROC_RESERVE_MEM / 4);
|
|
TEST_ASSERT_EQUAL(10 + 11, RTC_SLOW_MEM[18] & 0xffff);
|
|
}
|
|
|
|
TEST_CASE("ulp branch test", "[ulp]")
|
|
{
|
|
assert(CONFIG_ULP_COPROC_RESERVE_MEM >= 260 && "this test needs ULP_COPROC_RESERVE_MEM option set in menuconfig");
|
|
memset(RTC_SLOW_MEM, 0, CONFIG_ULP_COPROC_RESERVE_MEM);
|
|
const ulp_insn_t program[] = {
|
|
I_MOVI(R0, 34), // r0 = dst
|
|
M_LABEL(1),
|
|
I_MOVI(R1, 32),
|
|
I_LD(R1, R1, 0), // r1 = mem[33]
|
|
I_MOVI(R2, 33),
|
|
I_LD(R2, R2, 0), // r2 = mem[34]
|
|
I_SUBR(R3, R1, R2), // r3 = r1 - r2
|
|
I_ST(R3, R0, 0), // dst[0] = r3
|
|
I_ADDI(R0, R0, 1),
|
|
M_BL(1, 64),
|
|
I_HALT(),
|
|
};
|
|
RTC_SLOW_MEM[32] = 42;
|
|
RTC_SLOW_MEM[33] = 18;
|
|
hexdump(RTC_SLOW_MEM, CONFIG_ULP_COPROC_RESERVE_MEM / 4);
|
|
size_t size = sizeof(program)/sizeof(ulp_insn_t);
|
|
ulp_process_macros_and_load(0, program, &size);
|
|
ulp_run(0);
|
|
printf("\n\n");
|
|
hexdump(RTC_SLOW_MEM, CONFIG_ULP_COPROC_RESERVE_MEM / 4);
|
|
for (int i = 34; i < 64; ++i) {
|
|
TEST_ASSERT_EQUAL(42 - 18, RTC_SLOW_MEM[i] & 0xffff);
|
|
}
|
|
TEST_ASSERT_EQUAL(0, RTC_SLOW_MEM[64]);
|
|
}
|
|
|
|
TEST_CASE("ulp wakeup test", "[ulp][ignore]")
|
|
{
|
|
assert(CONFIG_ULP_COPROC_RESERVE_MEM >= 260 && "this test needs ULP_COPROC_RESERVE_MEM option set in menuconfig");
|
|
memset(RTC_SLOW_MEM, 0, CONFIG_ULP_COPROC_RESERVE_MEM);
|
|
const ulp_insn_t program[] = {
|
|
I_MOVI(R1, 1024),
|
|
M_LABEL(1),
|
|
I_DELAY(32000),
|
|
I_SUBI(R1, R1, 1),
|
|
M_BXZ(3),
|
|
I_RSHI(R3, R1, 5), // R3 = R1 / 32
|
|
I_ST(R1, R3, 16),
|
|
M_BX(1),
|
|
M_LABEL(3),
|
|
I_MOVI(R2, 42),
|
|
I_MOVI(R3, 15),
|
|
I_ST(R2, R3, 0),
|
|
I_WAKE(),
|
|
I_END(),
|
|
I_HALT()
|
|
};
|
|
size_t size = sizeof(program)/sizeof(ulp_insn_t);
|
|
ulp_process_macros_and_load(0, program, &size);
|
|
ulp_run(0);
|
|
esp_deep_sleep_enable_ulp_wakeup();
|
|
esp_deep_sleep_start();
|
|
}
|
|
|
|
TEST_CASE("ulp can write and read peripheral registers", "[ulp]")
|
|
{
|
|
assert(CONFIG_ULP_COPROC_RESERVE_MEM >= 260 && "this test needs ULP_COPROC_RESERVE_MEM option set in menuconfig");
|
|
CLEAR_PERI_REG_MASK(RTC_CNTL_STATE0_REG, RTC_CNTL_ULP_CP_SLP_TIMER_EN);
|
|
memset(RTC_SLOW_MEM, 0, CONFIG_ULP_COPROC_RESERVE_MEM);
|
|
REG_WRITE(RTC_CNTL_STORE1_REG, 0x89abcdef);
|
|
|
|
const ulp_insn_t program[] = {
|
|
I_MOVI(R1, 64),
|
|
I_RD_REG(RTC_CNTL_STORE1_REG, 0, 15),
|
|
I_ST(R0, R1, 0),
|
|
I_RD_REG(RTC_CNTL_STORE1_REG, 4, 11),
|
|
I_ST(R0, R1, 1),
|
|
I_RD_REG(RTC_CNTL_STORE1_REG, 16, 31),
|
|
I_ST(R0, R1, 2),
|
|
I_RD_REG(RTC_CNTL_STORE1_REG, 20, 27),
|
|
I_ST(R0, R1, 3),
|
|
I_WR_REG(RTC_CNTL_STORE0_REG, 0, 7, 0x89),
|
|
I_WR_REG(RTC_CNTL_STORE0_REG, 8, 15, 0xab),
|
|
I_WR_REG(RTC_CNTL_STORE0_REG, 16, 23, 0xcd),
|
|
I_WR_REG(RTC_CNTL_STORE0_REG, 24, 31, 0xef),
|
|
I_LD(R0, R1, 4),
|
|
I_ADDI(R0, R0, 1),
|
|
I_ST(R0, R1, 4),
|
|
I_END(),
|
|
I_HALT()
|
|
};
|
|
size_t size = sizeof(program)/sizeof(ulp_insn_t);
|
|
TEST_ESP_OK(ulp_process_macros_and_load(0, program, &size));
|
|
TEST_ESP_OK(ulp_run(0));
|
|
vTaskDelay(100/portTICK_PERIOD_MS);
|
|
|
|
TEST_ASSERT_EQUAL_HEX32(0xefcdab89, REG_READ(RTC_CNTL_STORE0_REG));
|
|
TEST_ASSERT_EQUAL_HEX16(0xcdef, RTC_SLOW_MEM[64] & 0xffff);
|
|
TEST_ASSERT_EQUAL_HEX16(0xde, RTC_SLOW_MEM[65] & 0xffff);
|
|
TEST_ASSERT_EQUAL_HEX16(0x89ab, RTC_SLOW_MEM[66] & 0xffff);
|
|
TEST_ASSERT_EQUAL_HEX16(0x9a, RTC_SLOW_MEM[67] & 0xffff);
|
|
TEST_ASSERT_EQUAL_HEX32(1 | (15 << 21) | (1 << 16), RTC_SLOW_MEM[68]);
|
|
}
|
|
|
|
TEST_CASE("ULP I_WR_REG instruction test", "[ulp]")
|
|
{
|
|
assert(CONFIG_ULP_COPROC_RESERVE_MEM >= 260 && "this test needs ULP_COPROC_RESERVE_MEM option set in menuconfig");
|
|
memset(RTC_SLOW_MEM, 0, CONFIG_ULP_COPROC_RESERVE_MEM);
|
|
typedef struct {
|
|
int low;
|
|
int width;
|
|
} wr_reg_test_item_t;
|
|
|
|
const wr_reg_test_item_t test_items[] = {
|
|
{0, 1}, {0, 2}, {0, 3}, {0, 4}, {0, 5}, {0, 6}, {0, 7}, {0, 8},
|
|
{3, 1}, {3, 2}, {3, 3}, {3, 4}, {3, 5}, {3, 6}, {3, 7}, {3, 8},
|
|
{15, 1}, {15, 2}, {15, 3}, {15, 4}, {15, 5}, {15, 6}, {15, 7}, {15, 8},
|
|
{16, 1}, {16, 2}, {16, 3}, {16, 4}, {16, 5}, {16, 6}, {16, 7}, {16, 8},
|
|
{18, 1}, {18, 2}, {18, 3}, {18, 4}, {18, 5}, {18, 6}, {18, 7}, {18, 8},
|
|
{24, 1}, {24, 2}, {24, 3}, {24, 4}, {24, 5}, {24, 6}, {24, 7}, {24, 8},
|
|
};
|
|
|
|
const size_t test_items_count =
|
|
sizeof(test_items)/sizeof(test_items[0]);
|
|
for (size_t i = 0; i < test_items_count; ++i) {
|
|
const uint32_t mask = (uint32_t) (((1ULL << test_items[i].width) - 1) << test_items[i].low);
|
|
const uint32_t not_mask = ~mask;
|
|
printf("#%2d: low: %2d width: %2d mask: %08x expected: %08x ", i,
|
|
test_items[i].low, test_items[i].width,
|
|
mask, not_mask);
|
|
|
|
REG_WRITE(RTC_CNTL_STORE0_REG, 0xffffffff);
|
|
REG_WRITE(RTC_CNTL_STORE1_REG, 0x00000000);
|
|
const ulp_insn_t program[] = {
|
|
I_WR_REG(RTC_CNTL_STORE0_REG,
|
|
test_items[i].low,
|
|
test_items[i].low + test_items[i].width - 1,
|
|
0),
|
|
I_WR_REG(RTC_CNTL_STORE1_REG,
|
|
test_items[i].low,
|
|
test_items[i].low + test_items[i].width - 1,
|
|
0xff & ((1 << test_items[i].width) - 1)),
|
|
I_END(),
|
|
I_HALT()
|
|
};
|
|
size_t size = sizeof(program)/sizeof(ulp_insn_t);
|
|
ulp_process_macros_and_load(0, program, &size);
|
|
ulp_run(0);
|
|
vTaskDelay(10/portTICK_PERIOD_MS);
|
|
uint32_t clear = REG_READ(RTC_CNTL_STORE0_REG);
|
|
uint32_t set = REG_READ(RTC_CNTL_STORE1_REG);
|
|
printf("clear: %08x set: %08x\n", clear, set);
|
|
TEST_ASSERT_EQUAL_HEX32(not_mask, clear);
|
|
TEST_ASSERT_EQUAL_HEX32(mask, set);
|
|
}
|
|
}
|
|
|
|
|
|
TEST_CASE("ulp controls RTC_IO", "[ulp][ignore]")
|
|
{
|
|
assert(CONFIG_ULP_COPROC_RESERVE_MEM >= 260 && "this test needs ULP_COPROC_RESERVE_MEM option set in menuconfig");
|
|
memset(RTC_SLOW_MEM, 0, CONFIG_ULP_COPROC_RESERVE_MEM);
|
|
const ulp_insn_t program[] = {
|
|
I_MOVI(R0, 0), // R0 is LED state
|
|
I_MOVI(R2, 16), // loop R2 from 16 down to 0
|
|
M_LABEL(4),
|
|
I_SUBI(R2, R2, 1),
|
|
M_BXZ(6),
|
|
I_ADDI(R0, R0, 1), // R0 = (R0 + 1) % 2
|
|
I_ANDI(R0, R0, 0x1),
|
|
M_BL(0, 1), // if R0 < 1 goto 0
|
|
M_LABEL(1),
|
|
I_WR_REG(RTC_GPIO_OUT_REG, 26, 27, 1), // RTC_GPIO12 = 1
|
|
M_BX(2), // goto 2
|
|
M_LABEL(0), // 0:
|
|
I_WR_REG(RTC_GPIO_OUT_REG, 26, 27, 0), // RTC_GPIO12 = 0
|
|
M_LABEL(2), // 2:
|
|
I_MOVI(R1, 100), // loop R1 from 100 down to 0
|
|
M_LABEL(3),
|
|
I_SUBI(R1, R1, 1),
|
|
M_BXZ(5),
|
|
I_DELAY(32000), // delay for a while
|
|
M_BX(3),
|
|
M_LABEL(5),
|
|
M_BX(4),
|
|
M_LABEL(6),
|
|
I_WAKE(), // wake up the SoC
|
|
I_END(), // stop ULP program timer
|
|
I_HALT()
|
|
};
|
|
const gpio_num_t led_gpios[] = {
|
|
GPIO_NUM_2,
|
|
GPIO_NUM_0,
|
|
GPIO_NUM_4
|
|
};
|
|
for (size_t i = 0; i < sizeof(led_gpios)/sizeof(led_gpios[0]); ++i) {
|
|
rtc_gpio_init(led_gpios[i]);
|
|
rtc_gpio_set_direction(led_gpios[i], RTC_GPIO_MODE_OUTPUT_ONLY);
|
|
rtc_gpio_set_level(led_gpios[i], 0);
|
|
}
|
|
size_t size = sizeof(program)/sizeof(ulp_insn_t);
|
|
ulp_process_macros_and_load(0, program, &size);
|
|
ulp_run(0);
|
|
esp_deep_sleep_enable_ulp_wakeup();
|
|
esp_deep_sleep_start();
|
|
}
|
|
|
|
TEST_CASE("ulp power consumption in deep sleep", "[ulp][ignore]")
|
|
{
|
|
assert(CONFIG_ULP_COPROC_RESERVE_MEM >= 4 && "this test needs ULP_COPROC_RESERVE_MEM option set in menuconfig");
|
|
ulp_insn_t insn = I_HALT();
|
|
RTC_SLOW_MEM[0] = *(uint32_t*) &insn;
|
|
|
|
REG_WRITE(SENS_ULP_CP_SLEEP_CYC0_REG, 0x8000);
|
|
|
|
ulp_run(0);
|
|
|
|
esp_deep_sleep_enable_ulp_wakeup();
|
|
esp_deep_sleep_enable_timer_wakeup(10 * 1000000);
|
|
esp_deep_sleep_start();
|
|
}
|
|
|
|
TEST_CASE("ulp timer setting", "[ulp]")
|
|
{
|
|
/*
|
|
* Run a simple ULP program which increments the counter, for one second.
|
|
* Program calls I_HALT each time and gets restarted by the timer.
|
|
* Compare the expected number of times the program runs with the actual.
|
|
*/
|
|
assert(CONFIG_ULP_COPROC_RESERVE_MEM >= 32 && "this test needs ULP_COPROC_RESERVE_MEM option set in menuconfig");
|
|
memset(RTC_SLOW_MEM, 0, CONFIG_ULP_COPROC_RESERVE_MEM);
|
|
|
|
const int offset = 6;
|
|
const ulp_insn_t program[] = {
|
|
I_MOVI(R1, offset), // r1 <- offset
|
|
I_LD(R2, R1, 0), // load counter
|
|
I_ADDI(R2, R2, 1), // counter += 1
|
|
I_ST(R2, R1, 0), // save counter
|
|
I_HALT(),
|
|
};
|
|
|
|
size_t size = sizeof(program)/sizeof(ulp_insn_t);
|
|
TEST_ESP_OK(ulp_process_macros_and_load(0, program, &size));
|
|
assert(offset >= size && "data offset needs to be greater or equal to program size");
|
|
TEST_ESP_OK(ulp_run(0));
|
|
// disable the ULP program timer — we will enable it later
|
|
CLEAR_PERI_REG_MASK(RTC_CNTL_STATE0_REG, RTC_CNTL_ULP_CP_SLP_TIMER_EN);
|
|
|
|
const uint32_t cycles_to_test[] = {0x80, 0x100, 0x200, 0x400, 0x800, 0x1000, 0x2000, 0x4000};
|
|
const size_t tests_count = sizeof(cycles_to_test) / sizeof(cycles_to_test[0]);
|
|
for (size_t i = 0; i < tests_count; ++i) {
|
|
// zero out the counter
|
|
RTC_SLOW_MEM[offset] = 0;
|
|
// set the number of slow clock cycles
|
|
REG_WRITE(SENS_ULP_CP_SLEEP_CYC0_REG, cycles_to_test[i]);
|
|
// enable the timer and wait for a second
|
|
SET_PERI_REG_MASK(RTC_CNTL_STATE0_REG, RTC_CNTL_ULP_CP_SLP_TIMER_EN);
|
|
vTaskDelay(1000 / portTICK_PERIOD_MS);
|
|
// get the counter value and stop the timer
|
|
uint32_t counter = RTC_SLOW_MEM[offset] & 0xffff;
|
|
CLEAR_PERI_REG_MASK(RTC_CNTL_STATE0_REG, RTC_CNTL_ULP_CP_SLP_TIMER_EN);
|
|
// compare the actual and expected numbers of iterations of ULP program
|
|
float expected_period = (cycles_to_test[i] + 16) / (float) rtc_clk_slow_freq_get_hz() + 5 / 8e6f;
|
|
float error = 1.0f - counter * expected_period;
|
|
printf("%u\t%u\t%.01f\t%.04f\n", cycles_to_test[i], counter, 1.0f / expected_period, error);
|
|
// Should be within 15%
|
|
TEST_ASSERT_INT_WITHIN(15, 0, (int) error * 100);
|
|
}
|
|
}
|
|
|
|
TEST_CASE("ulp can use TSENS in deep sleep", "[ulp][ignore]")
|
|
{
|
|
assert(CONFIG_ULP_COPROC_RESERVE_MEM >= 260 && "this test needs ULP_COPROC_RESERVE_MEM option set in menuconfig");
|
|
|
|
hexdump(RTC_SLOW_MEM, CONFIG_ULP_COPROC_RESERVE_MEM / 4);
|
|
printf("\n\n");
|
|
memset(RTC_SLOW_MEM, 0, CONFIG_ULP_COPROC_RESERVE_MEM);
|
|
|
|
// Allow TSENS to be controlled by the ULP
|
|
SET_PERI_REG_BITS(SENS_SAR_TSENS_CTRL_REG, SENS_TSENS_CLK_DIV, 10, SENS_TSENS_CLK_DIV_S);
|
|
SET_PERI_REG_BITS(SENS_SAR_MEAS_WAIT2_REG, SENS_FORCE_XPD_SAR, 3, SENS_FORCE_XPD_SAR_S);
|
|
CLEAR_PERI_REG_MASK(SENS_SAR_TSENS_CTRL_REG, SENS_TSENS_POWER_UP);
|
|
CLEAR_PERI_REG_MASK(SENS_SAR_TSENS_CTRL_REG, SENS_TSENS_DUMP_OUT);
|
|
CLEAR_PERI_REG_MASK(SENS_SAR_TSENS_CTRL_REG, SENS_TSENS_POWER_UP_FORCE);
|
|
|
|
// data start offset
|
|
size_t offset = 20;
|
|
// number of samples to collect
|
|
RTC_SLOW_MEM[offset] = (CONFIG_ULP_COPROC_RESERVE_MEM) / 4 - offset - 8;
|
|
// sample counter
|
|
RTC_SLOW_MEM[offset + 1] = 0;
|
|
|
|
const ulp_insn_t program[] = {
|
|
I_MOVI(R1, offset), // r1 <- offset
|
|
I_LD(R2, R1, 1), // r2 <- counter
|
|
I_LD(R3, R1, 0), // r3 <- length
|
|
I_SUBI(R3, R3, 1), // end = length - 1
|
|
I_SUBR(R3, R3, R2), // r3 = length - counter
|
|
M_BXF(1), // if overflow goto 1:
|
|
I_WR_REG(SENS_SAR_MEAS_WAIT2_REG, SENS_FORCE_XPD_SAR_S, SENS_FORCE_XPD_SAR_S + 1, 3),
|
|
I_TSENS(R0, 16383), // r0 <- tsens
|
|
I_WR_REG(SENS_SAR_MEAS_WAIT2_REG, SENS_FORCE_XPD_SAR_S, SENS_FORCE_XPD_SAR_S + 1, 0),
|
|
I_ST(R0, R2, offset + 4),
|
|
I_ADDI(R2, R2, 1), // counter += 1
|
|
I_ST(R2, R1, 1), // save counter
|
|
I_HALT(), // enter sleep
|
|
M_LABEL(1), // done with measurements
|
|
I_END(), // stop ULP timer
|
|
I_WAKE(), // initiate wakeup
|
|
I_HALT()
|
|
};
|
|
|
|
size_t size = sizeof(program)/sizeof(ulp_insn_t);
|
|
TEST_ESP_OK(ulp_process_macros_and_load(0, program, &size));
|
|
assert(offset >= size);
|
|
|
|
TEST_ESP_OK(ulp_run(0));
|
|
esp_deep_sleep_enable_timer_wakeup(4000000);
|
|
esp_deep_sleep_enable_ulp_wakeup();
|
|
esp_deep_sleep_start();
|
|
}
|
|
|
|
TEST_CASE("can use ADC in deep sleep", "[ulp][ignore]")
|
|
{
|
|
assert(CONFIG_ULP_COPROC_RESERVE_MEM >= 260 && "this test needs ULP_COPROC_RESERVE_MEM option set in menuconfig");
|
|
|
|
hexdump(RTC_SLOW_MEM, CONFIG_ULP_COPROC_RESERVE_MEM / 4);
|
|
printf("\n\n");
|
|
memset(RTC_SLOW_MEM, 0, CONFIG_ULP_COPROC_RESERVE_MEM);
|
|
|
|
SET_PERI_REG_BITS(SENS_SAR_START_FORCE_REG, SENS_SAR1_BIT_WIDTH, 3, SENS_SAR1_BIT_WIDTH_S);
|
|
SET_PERI_REG_BITS(SENS_SAR_START_FORCE_REG, SENS_SAR2_BIT_WIDTH, 3, SENS_SAR2_BIT_WIDTH_S);
|
|
|
|
SET_PERI_REG_BITS(SENS_SAR_READ_CTRL_REG, SENS_SAR1_SAMPLE_BIT, 0x3, SENS_SAR1_SAMPLE_BIT_S);
|
|
SET_PERI_REG_BITS(SENS_SAR_READ_CTRL2_REG, SENS_SAR2_SAMPLE_BIT, 0x3, SENS_SAR2_SAMPLE_BIT_S);
|
|
|
|
CLEAR_PERI_REG_MASK(SENS_SAR_MEAS_START2_REG, SENS_MEAS2_START_FORCE);
|
|
CLEAR_PERI_REG_MASK(SENS_SAR_MEAS_START1_REG, SENS_MEAS1_START_FORCE);
|
|
|
|
SET_PERI_REG_BITS(SENS_SAR_MEAS_WAIT2_REG, SENS_FORCE_XPD_SAR, 0, SENS_FORCE_XPD_SAR_S);
|
|
SET_PERI_REG_BITS(SENS_SAR_MEAS_WAIT2_REG, SENS_FORCE_XPD_AMP, 2, SENS_FORCE_XPD_AMP_S);
|
|
|
|
// SAR1 invert result
|
|
SET_PERI_REG_MASK(SENS_SAR_READ_CTRL_REG, SENS_SAR1_DATA_INV);
|
|
SET_PERI_REG_MASK(SENS_SAR_READ_CTRL_REG, SENS_SAR2_DATA_INV);
|
|
|
|
|
|
// const int adc = 1;
|
|
// const int channel = 1;
|
|
// const int atten = 3;
|
|
// const int gpio_num = 0;
|
|
|
|
const int adc = 0;
|
|
const int channel = 0;
|
|
const int atten = 0;
|
|
const int gpio_num = 36;
|
|
|
|
rtc_gpio_init(gpio_num);
|
|
|
|
CLEAR_PERI_REG_MASK(SENS_SAR_MEAS_START1_REG, SENS_SAR1_EN_PAD_FORCE_M);
|
|
CLEAR_PERI_REG_MASK(SENS_SAR_MEAS_START2_REG, SENS_SAR2_EN_PAD_FORCE_M);
|
|
|
|
SET_PERI_REG_BITS(SENS_SAR_ATTEN1_REG, 3, atten, 2 * channel); //set SAR1 attenuation
|
|
SET_PERI_REG_BITS(SENS_SAR_ATTEN2_REG, 3, atten, 2 * channel); //set SAR2 attenuation
|
|
|
|
// data start offset
|
|
size_t offset = 20;
|
|
// number of samples to collect
|
|
RTC_SLOW_MEM[offset] = (CONFIG_ULP_COPROC_RESERVE_MEM) / 4 - offset - 8;
|
|
// sample counter
|
|
RTC_SLOW_MEM[offset + 1] = 0;
|
|
|
|
const ulp_insn_t program[] = {
|
|
I_MOVI(R1, offset), // r1 <- offset
|
|
I_LD(R2, R1, 1), // r2 <- counter
|
|
I_LD(R3, R1, 0), // r3 <- length
|
|
I_SUBI(R3, R3, 1), // end = length - 1
|
|
I_SUBR(R3, R3, R2), // r3 = length - counter
|
|
M_BXF(1), // if overflow goto 1:
|
|
I_ADC(R0, adc, channel), // r0 <- ADC
|
|
I_ST(R0, R2, offset + 4),
|
|
I_ADDI(R2, R2, 1), // counter += 1
|
|
I_ST(R2, R1, 1), // save counter
|
|
I_HALT(),
|
|
M_LABEL(1), // done with measurements
|
|
I_END(), // stop ULP program timer
|
|
I_HALT()
|
|
};
|
|
|
|
size_t size = sizeof(program)/sizeof(ulp_insn_t);
|
|
TEST_ESP_OK(ulp_process_macros_and_load(0, program, &size));
|
|
assert(offset >= size);
|
|
|
|
TEST_ESP_OK(ulp_run(0));
|
|
esp_deep_sleep_enable_timer_wakeup(4000000);
|
|
esp_deep_sleep_start();
|
|
}
|
|
|