OVMS3-idf/docs/en/get-started/get-started-pico-kit-v3.rst
Angus Gratton a67d5d89e0 Replace all DOS line endings with Unix
Command run was:
git ls-tree -r HEAD --name-only | xargs dos2unix
2018-07-12 19:10:37 +08:00

66 lines
3.1 KiB
ReStructuredText
Raw Blame History

This file contains ambiguous Unicode characters

This file contains Unicode characters that might be confused with other characters. If you think that this is intentional, you can safely ignore this warning. Use the Escape button to reveal them.

ESP32-PICO-KIT V3 Getting Started Guide
=======================================
This user guide shows how to get started with the ESP32-PICO-KIT V3 mini development board. For description of other versions of the ESP32-PICO-KIT check :doc:`../hw-reference/index`.
What You Need
-------------
* 1 × ESP32-PICO-KIT V3 mini development board
* 1 × USB A / Micro USB B cable
* 1 × PC loaded with Windows, Linux or Mac OS
Overview
--------
ESP32-PICO-KIT V3 is a mini development board based on the ESP32-PICO-D4 SIP module produced by `Espressif <https://espressif.com>`_. All the IO signals and system power on ESP32-PICO-D4 are led out through two standard 20 pin x 0.1" pitch headers on both sides for easy interfacing. The development board integrates a USB-UART Bridge circuit, allowing the developers to connect the development board to a PC's USB port for downloads and debugging.
Functional Description
----------------------
The following list and figure below describe key components, interfaces and controls of ESP32-PICO-KIT V3 board.
ESP32-PICO-D4
Standard ESP32-PICO-D4 module soldered to the ESP32-PICO-KIT V3 board. The complete system of the ESP32 chip has been integrated into the SIP module, requiring only external antenna with LC matching network, decoupling capacitors and pull-up resistors for EN signals to function properly.
USB-UART Bridge
A single chip USB-UART bridge provides up to 1 Mbps transfers rates.
I/O
All the pins on ESP32-PICO-D4 are broken out to the pin headers on the board. Users can program ESP32 to enable multiple functions such as PWM, ADC, DAC, I2C, I2S, SPI, etc.
Micro USB Port
USB interface. It functions as the power supply for the board and the communication interface between PC and ESP32-PICO-KIT V3.
EN Button
Reset button; pressing this button resets the system.
BOOT Button
Holding down the Boot button and pressing the EN button initiates the firmware download mode. Then user can download firmware through the serial port.
.. figure:: ../../_static/esp32-pico-kit-v3-layout.jpg
:align: center
:alt: ESP32-PICO-KIT V3 board layout
:figclass: align-center
ESP32-PICO-KIT V3 board layout
Start Application Development
------------------------------
Before powering up the ESP32-PICO-KIT V3, please make sure that the board has been received in good condition with no obvious signs of damage.
To start development of applications, proceed to section :doc:`index`, that will walk you through the following steps:
* :ref:`get-started-setup-toolchain` in your PC to develop applications for ESP32 in C language
* :ref:`get-started-connect` the module to the PC and verify if it is accessible
* :ref:`get-started-build-flash` an example application to the ESP32
* :ref:`get-started-build-monitor` instantly what the application is doing
Related Documents
-----------------
* `ESP32-PICO-KIT V3 schematic <https://dl.espressif.com/dl/schematics/esp32-pico-kit-v3_schematic.pdf>`_ (PDF)
* `ESP32-PICO-D4 Datasheet <http://espressif.com/sites/default/files/documentation/esp32-pico-d4_datasheet_en.pdf>`_ (PDF)
* :doc:`../hw-reference/index`