3abdd2207d
check master read write functions with array of registers) fix master serial processing code and modbus controller to work with register array modbus_master: add reading and writing of test value array (58 registers) to check failure is gone remove parameter temporary buffer from modbus controller to allow more than 24 byte writes driver: fix issue with TOUT feature driver: fix uart_rx_timeout issue driver: fix issue with rxfifo_tout_int_raw not triggered when received fifo_len = 120 byte and all bytes read out of fifo as result of rxfifo_full_int_raw driver: add function uart_internal_set_always_rx_timeout() to always handle tout interrupt examples: call uart_internal_set_always_rx_timeout() to handle tout interrupt correctly examples: update examples to use tout feature driver: reflect changes of uart_set_always_rx_timeout() function, change uart.c driver: change conditions to trigger workaround for tout feature in uart.c driver: change uart_set_always_rx_timeout() freemodbus: fix tabs, remove commented code driver: remove uart_ll_is_rx_idle()
351 lines
10 KiB
C
351 lines
10 KiB
C
/*
|
|
* FreeModbus Libary: A portable Modbus implementation for Modbus ASCII/RTU.
|
|
* Copyright (c) 2006 Christian Walter <wolti@sil.at>
|
|
* All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in the
|
|
* documentation and/or other materials provided with the distribution.
|
|
* 3. The name of the author may not be used to endorse or promote products
|
|
* derived from this software without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
|
|
* IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
|
|
* OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
|
|
* IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
|
|
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
|
|
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
|
|
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
|
|
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
|
|
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
|
|
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
|
|
*
|
|
* File: $Id: mbrtu.c,v 1.18 2007/09/12 10:15:56 wolti Exp $
|
|
*/
|
|
|
|
/* ----------------------- System includes ----------------------------------*/
|
|
#include "stdlib.h"
|
|
#include "string.h"
|
|
|
|
/* ----------------------- Platform includes --------------------------------*/
|
|
#include "port.h"
|
|
|
|
/* ----------------------- Modbus includes ----------------------------------*/
|
|
#include "mb.h"
|
|
#include "mbrtu.h"
|
|
#include "mbframe.h"
|
|
|
|
#include "mbcrc.h"
|
|
#include "mbport.h"
|
|
|
|
#if MB_SLAVE_RTU_ENABLED > 0
|
|
|
|
/* ----------------------- Type definitions ---------------------------------*/
|
|
typedef enum
|
|
{
|
|
STATE_RX_INIT, /*!< Receiver is in initial state. */
|
|
STATE_RX_IDLE, /*!< Receiver is in idle state. */
|
|
STATE_RX_RCV, /*!< Frame is beeing received. */
|
|
STATE_RX_ERROR /*!< If the frame is invalid. */
|
|
} eMBRcvState;
|
|
|
|
typedef enum
|
|
{
|
|
STATE_TX_IDLE, /*!< Transmitter is in idle state. */
|
|
STATE_TX_XMIT /*!< Transmitter is in transfer state. */
|
|
} eMBSndState;
|
|
|
|
/* ----------------------- Shared variables ---------------------------------*/
|
|
extern volatile UCHAR ucMbSlaveBuf[];
|
|
|
|
/* ----------------------- Static variables ---------------------------------*/
|
|
static volatile eMBSndState eSndState;
|
|
static volatile eMBRcvState eRcvState;
|
|
|
|
static volatile UCHAR *pucSndBufferCur;
|
|
static volatile USHORT usSndBufferCount;
|
|
|
|
static volatile USHORT usRcvBufferPos;
|
|
static volatile UCHAR *ucRTUBuf = ucMbSlaveBuf;
|
|
|
|
/* ----------------------- Start implementation -----------------------------*/
|
|
eMBErrorCode
|
|
eMBRTUInit( UCHAR ucSlaveAddress, UCHAR ucPort, ULONG ulBaudRate, eMBParity eParity )
|
|
{
|
|
eMBErrorCode eStatus = MB_ENOERR;
|
|
ULONG usTimerT35_50us;
|
|
|
|
( void )ucSlaveAddress;
|
|
ENTER_CRITICAL_SECTION( );
|
|
|
|
/* Modbus RTU uses 8 Databits. */
|
|
if( xMBPortSerialInit( ucPort, ulBaudRate, 8, eParity ) != TRUE )
|
|
{
|
|
eStatus = MB_EPORTERR;
|
|
}
|
|
else
|
|
{
|
|
/* If baudrate > 19200 then we should use the fixed timer values
|
|
* t35 = 1750us. Otherwise t35 must be 3.5 times the character time.
|
|
*/
|
|
if( ulBaudRate > 19200 )
|
|
{
|
|
usTimerT35_50us = 35; /* 1800us. */
|
|
}
|
|
else
|
|
{
|
|
/* The timer reload value for a character is given by:
|
|
*
|
|
* ChTimeValue = Ticks_per_1s / ( Baudrate / 11 )
|
|
* = 11 * Ticks_per_1s / Baudrate
|
|
* = 220000 / Baudrate
|
|
* The reload for t3.5 is 1.5 times this value and similary
|
|
* for t3.5.
|
|
*/
|
|
usTimerT35_50us = ( 7UL * 220000UL ) / ( 2UL * ulBaudRate );
|
|
}
|
|
if( xMBPortTimersInit( ( USHORT ) usTimerT35_50us ) != TRUE )
|
|
{
|
|
eStatus = MB_EPORTERR;
|
|
}
|
|
}
|
|
EXIT_CRITICAL_SECTION( );
|
|
|
|
return eStatus;
|
|
}
|
|
|
|
void
|
|
eMBRTUStart( void )
|
|
{
|
|
ENTER_CRITICAL_SECTION( );
|
|
/* Initially the receiver is in the state STATE_RX_INIT. we start
|
|
* the timer and if no character is received within t3.5 we change
|
|
* to STATE_RX_IDLE. This makes sure that we delay startup of the
|
|
* modbus protocol stack until the bus is free.
|
|
*/
|
|
eRcvState = STATE_RX_INIT;
|
|
vMBPortSerialEnable( TRUE, FALSE );
|
|
vMBPortTimersEnable( );
|
|
|
|
EXIT_CRITICAL_SECTION( );
|
|
}
|
|
|
|
void
|
|
eMBRTUStop( void )
|
|
{
|
|
ENTER_CRITICAL_SECTION( );
|
|
vMBPortSerialEnable( FALSE, FALSE );
|
|
vMBPortTimersDisable( );
|
|
EXIT_CRITICAL_SECTION( );
|
|
}
|
|
|
|
eMBErrorCode
|
|
eMBRTUReceive( UCHAR * pucRcvAddress, UCHAR ** pucFrame, USHORT * pusLength )
|
|
{
|
|
eMBErrorCode eStatus = MB_ENOERR;
|
|
|
|
ENTER_CRITICAL_SECTION( );
|
|
assert( usRcvBufferPos < MB_SER_PDU_SIZE_MAX );
|
|
|
|
/* Length and CRC check */
|
|
if( ( usRcvBufferPos >= MB_SER_PDU_SIZE_MIN )
|
|
&& ( usMBCRC16( ( UCHAR * ) ucRTUBuf, usRcvBufferPos ) == 0 ) )
|
|
{
|
|
/* Save the address field. All frames are passed to the upper layed
|
|
* and the decision if a frame is used is done there.
|
|
*/
|
|
*pucRcvAddress = ucRTUBuf[MB_SER_PDU_ADDR_OFF];
|
|
|
|
/* Total length of Modbus-PDU is Modbus-Serial-Line-PDU minus
|
|
* size of address field and CRC checksum.
|
|
*/
|
|
*pusLength = ( USHORT )( usRcvBufferPos - MB_SER_PDU_PDU_OFF - MB_SER_PDU_SIZE_CRC );
|
|
|
|
/* Return the start of the Modbus PDU to the caller. */
|
|
*pucFrame = ( UCHAR * ) & ucRTUBuf[MB_SER_PDU_PDU_OFF];
|
|
}
|
|
else
|
|
{
|
|
eStatus = MB_EIO;
|
|
}
|
|
|
|
EXIT_CRITICAL_SECTION( );
|
|
return eStatus;
|
|
}
|
|
|
|
eMBErrorCode
|
|
eMBRTUSend( UCHAR ucSlaveAddress, const UCHAR * pucFrame, USHORT usLength )
|
|
{
|
|
eMBErrorCode eStatus = MB_ENOERR;
|
|
USHORT usCRC16;
|
|
|
|
ENTER_CRITICAL_SECTION( );
|
|
|
|
/* Check if the receiver is still in idle state. If not we where to
|
|
* slow with processing the received frame and the master sent another
|
|
* frame on the network. We have to abort sending the frame.
|
|
*/
|
|
if( eRcvState == STATE_RX_IDLE )
|
|
{
|
|
/* First byte before the Modbus-PDU is the slave address. */
|
|
pucSndBufferCur = ( UCHAR * ) pucFrame - 1;
|
|
usSndBufferCount = 1;
|
|
|
|
/* Now copy the Modbus-PDU into the Modbus-Serial-Line-PDU. */
|
|
pucSndBufferCur[MB_SER_PDU_ADDR_OFF] = ucSlaveAddress;
|
|
usSndBufferCount += usLength;
|
|
|
|
/* Calculate CRC16 checksum for Modbus-Serial-Line-PDU. */
|
|
usCRC16 = usMBCRC16( ( UCHAR * ) pucSndBufferCur, usSndBufferCount );
|
|
ucRTUBuf[usSndBufferCount++] = ( UCHAR )( usCRC16 & 0xFF );
|
|
ucRTUBuf[usSndBufferCount++] = ( UCHAR )( usCRC16 >> 8 );
|
|
|
|
/* Activate the transmitter. */
|
|
eSndState = STATE_TX_XMIT;
|
|
vMBPortSerialEnable( FALSE, TRUE );
|
|
}
|
|
else
|
|
{
|
|
eStatus = MB_EIO;
|
|
}
|
|
EXIT_CRITICAL_SECTION( );
|
|
return eStatus;
|
|
}
|
|
|
|
BOOL
|
|
xMBRTUReceiveFSM( void )
|
|
{
|
|
BOOL xStatus = FALSE;
|
|
UCHAR ucByte;
|
|
|
|
assert( eSndState == STATE_TX_IDLE );
|
|
|
|
/* Always read the character. */
|
|
xStatus = xMBPortSerialGetByte( ( CHAR * ) & ucByte );
|
|
|
|
switch ( eRcvState )
|
|
{
|
|
/* If we have received a character in the init state we have to
|
|
* wait until the frame is finished.
|
|
*/
|
|
case STATE_RX_INIT:
|
|
vMBPortTimersEnable( );
|
|
break;
|
|
|
|
/* In the error state we wait until all characters in the
|
|
* damaged frame are transmitted.
|
|
*/
|
|
case STATE_RX_ERROR:
|
|
vMBPortTimersEnable( );
|
|
break;
|
|
|
|
/* In the idle state we wait for a new character. If a character
|
|
* is received the t1.5 and t3.5 timers are started and the
|
|
* receiver is in the state STATE_RX_RCV.
|
|
*/
|
|
case STATE_RX_IDLE:
|
|
usRcvBufferPos = 0;
|
|
ucRTUBuf[usRcvBufferPos++] = ucByte;
|
|
eRcvState = STATE_RX_RCV;
|
|
|
|
/* Enable t3.5 timers. */
|
|
vMBPortTimersEnable( );
|
|
break;
|
|
|
|
/* We are currently receiving a frame. Reset the timer after
|
|
* every character received. If more than the maximum possible
|
|
* number of bytes in a modbus frame is received the frame is
|
|
* ignored.
|
|
*/
|
|
case STATE_RX_RCV:
|
|
if( usRcvBufferPos < MB_SER_PDU_SIZE_MAX )
|
|
{
|
|
if ( xStatus ) {
|
|
ucRTUBuf[usRcvBufferPos++] = ucByte;
|
|
}
|
|
}
|
|
else
|
|
{
|
|
eRcvState = STATE_RX_ERROR;
|
|
}
|
|
vMBPortTimersEnable( );
|
|
break;
|
|
}
|
|
|
|
return xStatus;
|
|
}
|
|
|
|
BOOL
|
|
xMBRTUTransmitFSM( void )
|
|
{
|
|
BOOL xNeedPoll = TRUE;
|
|
|
|
assert( eRcvState == STATE_RX_IDLE );
|
|
|
|
switch ( eSndState )
|
|
{
|
|
/* We should not get a transmitter event if the transmitter is in
|
|
* idle state. */
|
|
case STATE_TX_IDLE:
|
|
break;
|
|
|
|
case STATE_TX_XMIT:
|
|
/* check if we are finished. */
|
|
if( usSndBufferCount != 0 )
|
|
{
|
|
xMBPortSerialPutByte( ( CHAR )*pucSndBufferCur );
|
|
pucSndBufferCur++; /* next byte in sendbuffer. */
|
|
usSndBufferCount--;
|
|
}
|
|
else
|
|
{
|
|
xMBPortEventPost( EV_FRAME_TRANSMIT );
|
|
xNeedPoll = FALSE;
|
|
eSndState = STATE_TX_IDLE;
|
|
vMBPortTimersEnable( );
|
|
}
|
|
break;
|
|
}
|
|
|
|
return xNeedPoll;
|
|
}
|
|
|
|
BOOL MB_PORT_ISR_ATTR
|
|
xMBRTUTimerT35Expired( void )
|
|
{
|
|
BOOL xNeedPoll = FALSE;
|
|
|
|
switch ( eRcvState )
|
|
{
|
|
/* Timer t35 expired. Startup phase is finished. */
|
|
case STATE_RX_INIT:
|
|
xNeedPoll = xMBPortEventPost( EV_READY );
|
|
break;
|
|
|
|
/* A frame was received and t35 expired. Notify the listener that
|
|
* a new frame was received. */
|
|
case STATE_RX_RCV:
|
|
xNeedPoll = xMBPortEventPost( EV_FRAME_RECEIVED );
|
|
break;
|
|
|
|
/* An error occured while receiving the frame. */
|
|
case STATE_RX_ERROR:
|
|
break;
|
|
|
|
/* Function called in an illegal state. */
|
|
default:
|
|
assert( ( eRcvState == STATE_RX_IDLE ) || ( eRcvState == STATE_RX_ERROR ) );
|
|
}
|
|
|
|
vMBPortTimersDisable( );
|
|
eRcvState = STATE_RX_IDLE;
|
|
|
|
return xNeedPoll;
|
|
}
|
|
#endif
|