OVMS3-idf/examples/peripherals/spi_master/main/spi_master.c

275 lines
10 KiB
C

/* SPI Master example
This example code is in the Public Domain (or CC0 licensed, at your option.)
Unless required by applicable law or agreed to in writing, this
software is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR
CONDITIONS OF ANY KIND, either express or implied.
*/
#include <stdio.h>
#include <stdlib.h>
#include <string.h>
#include "freertos/FreeRTOS.h"
#include "freertos/task.h"
#include "esp_system.h"
#include "driver/spi_master.h"
#include "soc/gpio_struct.h"
#include "driver/gpio.h"
/*
This code displays some fancy graphics on the ILI9341-based 320x240 LCD on an ESP-WROVER_KIT board.
It is not very fast, even when the SPI transfer itself happens at 8MHz and with DMA, because
the rest of the code is not very optimized. Especially calculating the image line-by-line
is inefficient; it would be quicker to send an entire screenful at once. This example does, however,
demonstrate the use of both spi_device_transmit as well as spi_device_queue_trans/spi_device_get_trans_result
as well as pre-transmit callbacks.
Some info about the ILI9341: It has an C/D line, which is connected to a GPIO here. It expects this
line to be low for a command and high for data. We use a pre-transmit callback here to control that
line: every transaction has as the user-definable argument the needed state of the D/C line and just
before the transaction is sent, the callback will set this line to the correct state.
*/
#define PIN_NUM_MISO 25
#define PIN_NUM_MOSI 23
#define PIN_NUM_CLK 19
#define PIN_NUM_CS 22
#define PIN_NUM_DC 21
#define PIN_NUM_RST 18
#define PIN_NUM_BCKL 5
/*
The ILI9341 needs a bunch of command/argument values to be initialized. They are stored in this struct.
*/
typedef struct {
uint8_t cmd;
uint8_t data[16];
uint8_t databytes; //No of data in data; bit 7 = delay after set; 0xFF = end of cmds.
} ili_init_cmd_t;
static const ili_init_cmd_t ili_init_cmds[]={
{0xCF, {0x00, 0x83, 0X30}, 3},
{0xED, {0x64, 0x03, 0X12, 0X81}, 4},
{0xE8, {0x85, 0x01, 0x79}, 3},
{0xCB, {0x39, 0x2C, 0x00, 0x34, 0x02}, 5},
{0xF7, {0x20}, 1},
{0xEA, {0x00, 0x00}, 2},
{0xC0, {0x26}, 1},
{0xC1, {0x11}, 1},
{0xC5, {0x35, 0x3E}, 2},
{0xC7, {0xBE}, 1},
{0x36, {0x28}, 1},
{0x3A, {0x55}, 1},
{0xB1, {0x00, 0x1B}, 2},
{0xF2, {0x08}, 1},
{0x26, {0x01}, 1},
{0xE0, {0x1F, 0x1A, 0x18, 0x0A, 0x0F, 0x06, 0x45, 0X87, 0x32, 0x0A, 0x07, 0x02, 0x07, 0x05, 0x00}, 15},
{0XE1, {0x00, 0x25, 0x27, 0x05, 0x10, 0x09, 0x3A, 0x78, 0x4D, 0x05, 0x18, 0x0D, 0x38, 0x3A, 0x1F}, 15},
{0x2A, {0x00, 0x00, 0x00, 0xEF}, 4},
{0x2B, {0x00, 0x00, 0x01, 0x3f}, 4},
{0x2C, {0}, 0},
{0xB7, {0x07}, 1},
{0xB6, {0x0A, 0x82, 0x27, 0x00}, 4},
{0x11, {0}, 0x80},
{0x29, {0}, 0x80},
{0, {0}, 0xff},
};
//Send a command to the ILI9341. Uses spi_device_transmit, which waits until the transfer is complete.
void ili_cmd(spi_device_handle_t spi, const uint8_t cmd)
{
esp_err_t ret;
spi_transaction_t t;
memset(&t, 0, sizeof(t)); //Zero out the transaction
t.length=8; //Command is 8 bits
t.tx_buffer=&cmd; //The data is the cmd itself
t.user=(void*)0; //D/C needs to be set to 0
ret=spi_device_transmit(spi, &t); //Transmit!
assert(ret==ESP_OK); //Should have had no issues.
}
//Send data to the ILI9341. Uses spi_device_transmit, which waits until the transfer is complete.
void ili_data(spi_device_handle_t spi, const uint8_t *data, int len)
{
esp_err_t ret;
spi_transaction_t t;
if (len==0) return; //no need to send anything
memset(&t, 0, sizeof(t)); //Zero out the transaction
t.length=len*8; //Len is in bytes, transaction length is in bits.
t.tx_buffer=data; //Data
t.user=(void*)1; //D/C needs to be set to 1
ret=spi_device_transmit(spi, &t); //Transmit!
assert(ret==ESP_OK); //Should have had no issues.
}
//This function is called (in irq context!) just before a transmission starts. It will
//set the D/C line to the value indicated in the user field.
void ili_spi_pre_transfer_callback(spi_transaction_t *t)
{
int dc=(int)t->user;
gpio_set_level(PIN_NUM_DC, dc);
}
//Initialize the display
void ili_init(spi_device_handle_t spi)
{
int cmd=0;
//Initialize non-SPI GPIOs
gpio_set_direction(PIN_NUM_DC, GPIO_MODE_OUTPUT);
gpio_set_direction(PIN_NUM_RST, GPIO_MODE_OUTPUT);
gpio_set_direction(PIN_NUM_BCKL, GPIO_MODE_OUTPUT);
//Reset the display
gpio_set_level(PIN_NUM_RST, 0);
vTaskDelay(100 / portTICK_RATE_MS);
gpio_set_level(PIN_NUM_RST, 1);
vTaskDelay(100 / portTICK_RATE_MS);
//Send all the commands
while (ili_init_cmds[cmd].databytes!=0xff) {
ili_cmd(spi, ili_init_cmds[cmd].cmd);
ili_data(spi, ili_init_cmds[cmd].data, ili_init_cmds[cmd].databytes&0x1F);
if (ili_init_cmds[cmd].databytes&0x80) {
vTaskDelay(100 / portTICK_RATE_MS);
}
cmd++;
}
///Enable backlight
gpio_set_level(PIN_NUM_BCKL, 0);
}
//To send a line we have to send a command, 2 data bytes, another command, 2 more data bytes and another command
//before sending the line data itself; a total of 6 transactions. (We can't put all of this in just one transaction
//because the D/C line needs to be toggled in the middle.)
//This routine queues these commands up so they get sent as quickly as possible.
void send_line(spi_device_handle_t spi, int ypos, uint16_t *line)
{
esp_err_t ret;
int x;
//Transaction descriptors. Declared static so they're not allocated on the stack; we need this memory even when this
//function is finished because the SPI driver needs access to it even while we're already calculating the next line.
static spi_transaction_t trans[6];
//In theory, it's better to initialize trans and data only once and hang on to the initialized
//variables. We allocate them on the stack, so we need to re-init them each call.
for (x=0; x<6; x++) {
memset(&trans[x], 0, sizeof(spi_transaction_t));
if ((x&1)==0) {
//Even transfers are commands
trans[x].length=8;
trans[x].user=(void*)0;
} else {
//Odd transfers are data
trans[x].length=8*4;
trans[x].user=(void*)1;
}
trans[x].flags=SPI_TRANS_USE_TXDATA;
}
trans[0].tx_data[0]=0x2A; //Column Address Set
trans[1].tx_data[0]=0; //Start Col High
trans[1].tx_data[1]=0; //Start Col Low
trans[1].tx_data[2]=(320)>>8; //End Col High
trans[1].tx_data[3]=(320)&0xff; //End Col Low
trans[2].tx_data[0]=0x2B; //Page address set
trans[3].tx_data[0]=ypos>>8; //Start page high
trans[3].tx_data[1]=ypos&0xff; //start page low
trans[3].tx_data[2]=(ypos+1)>>8; //end page high
trans[3].tx_data[3]=(ypos+1)&0xff; //end page low
trans[4].tx_data[0]=0x2C; //memory write
trans[5].tx_buffer=line; //finally send the line data
trans[5].length=320*2*8; //Data length, in bits
trans[5].flags=0; //undo SPI_TRANS_USE_TXDATA flag
//Queue all transactions.
for (x=0; x<6; x++) {
ret=spi_device_queue_trans(spi, &trans[x], portMAX_DELAY);
assert(ret==ESP_OK);
}
//When we are here, the SPI driver is busy (in the background) getting the transactions sent. That happens
//mostly using DMA, so the CPU doesn't have much to do here. We're not going to wait for the transaction to
//finish because we may as well spend the time calculating the next line. When that is done, we can call
//send_line_finish, which will wait for the transfers to be done and check their status.
}
void send_line_finish(spi_device_handle_t spi)
{
spi_transaction_t *rtrans;
esp_err_t ret;
//Wait for all 6 transactions to be done and get back the results.
for (int x=0; x<6; x++) {
ret=spi_device_get_trans_result(spi, &rtrans, portMAX_DELAY);
assert(ret==ESP_OK);
//We could inspect rtrans now if we received any info back. The LCD is treated as write-only, though.
}
}
//Simple routine to generate some patterns and send them to the LCD. Don't expect anything too
//impressive. Because the SPI driver handles transactions in the background, we can calculate the next line
//while the previous one is being sent.
void display_pretty_colors(spi_device_handle_t spi)
{
uint16_t line[2][320];
int x, y, frame=0;
//Indexes of the line currently being sent to the LCD and the line we're calculating.
int sending_line=-1;
int calc_line=0;
while(1) {
frame++;
for (y=0; y<240; y++) {
//Calculate a line.
for (x=0; x<320; x++) {
line[calc_line][x]=((x<<3)^(y<<3)^(frame+x*y));
}
//Finish up the sending process of the previous line, if any
if (sending_line!=-1) send_line_finish(spi);
//Swap sending_line and calc_line
sending_line=calc_line;
calc_line=(calc_line==1)?0:1;
//Send the line we currently calculated.
send_line(spi, y, line[sending_line]);
//The line is queued up for sending now; the actual sending happens in the
//background. We can go on to calculate the next line as long as we do not
//touch line[sending_line]; the SPI sending process is still reading from that.
}
}
}
void app_main()
{
esp_err_t ret;
spi_device_handle_t spi;
spi_bus_config_t buscfg={
.miso_io_num=PIN_NUM_MISO,
.mosi_io_num=PIN_NUM_MOSI,
.sclk_io_num=PIN_NUM_CLK,
.quadwp_io_num=-1,
.quadhd_io_num=-1
};
spi_device_interface_config_t devcfg={
.clock_speed_hz=10000000, //Clock out at 10 MHz
.mode=0, //SPI mode 0
.spics_io_num=PIN_NUM_CS, //CS pin
.queue_size=7, //We want to be able to queue 7 transactions at a time
.pre_cb=ili_spi_pre_transfer_callback, //Specify pre-transfer callback to handle D/C line
};
//Initialize the SPI bus
ret=spi_bus_initialize(HSPI_HOST, &buscfg, 1);
assert(ret==ESP_OK);
//Attach the LCD to the SPI bus
ret=spi_bus_add_device(HSPI_HOST, &devcfg, &spi);
assert(ret==ESP_OK);
//Initialize the LCD
ili_init(spi);
//Go do nice stuff.
display_pretty_colors(spi);
}