268 lines
No EOL
10 KiB
ReStructuredText
268 lines
No EOL
10 KiB
ReStructuredText
SD Pullup Requirements
|
|
======================
|
|
|
|
CMD and DATA lines D0-D3 of the slave should be pulled up by 10 kOhm resistor
|
|
even in 1-bit mode or SPI mode. The pullups of the slave cards should be
|
|
connected even if they're not connected to the host.
|
|
|
|
The MTDI strapping pin by default is incompatible with DAT2 line pullup when
|
|
the flash is 3.3 V. See :ref:`technical_detail_sdio` below.
|
|
|
|
.. _existing_issues_official_modules_sdio:
|
|
|
|
Possible Issues
|
|
---------------
|
|
|
|
Here is a list of Espressif chips, official modules and development kits and
|
|
the issues they may have during SDIO development. Since the requirements are
|
|
for the pullups on the SD bus, the issues should be resolved no matter if it
|
|
is a host or slave. Each issue is linked to its solution. The solution for a
|
|
specific issue may be different for host and slave.
|
|
|
|
Official modules are usually without the sufficient pullups on all 6 pins, it
|
|
is suggested to select one of the development kits for either host or slave
|
|
to provide such pullups.
|
|
|
|
Chips
|
|
^^^^^
|
|
|
|
- ESP32 (except D2WD, see `ESP32 datasheet <https://www.espressif.com/sites/default/files/documentation/esp32_datasheet_en.pdf>`_):
|
|
:ref:`sd_pullup_no_pullups`, whether the strapping conflicts with DAT2 is determined
|
|
by the flash you are using. Please see :ref:`strapping_conflicts_dat2` if
|
|
your flash chip is 3.3 V.
|
|
|
|
- ESP32-D2WD:
|
|
:ref:`sd_pullup_no_pullups`, :ref:`no_pullup_on_gpio12`
|
|
|
|
- ESP32-PICO-D4:
|
|
:ref:`sd_pullup_no_pullups`, :ref:`strapping_conflicts_dat2`
|
|
|
|
Modules
|
|
^^^^^^^
|
|
|
|
- ESP32-WROOM-32 Series:
|
|
Including ESP32-WROOM-32, ESP32-WROOM-32D, ESP32-WROOM-32U and
|
|
ESP32-SOLO-1.
|
|
|
|
:ref:`sd_pullup_no_pullups`, :ref:`strapping_conflicts_dat2`.
|
|
|
|
- ESP32-WROVER Series:
|
|
Including ESP32-WROVER and ESP32-WROVER-I.
|
|
|
|
:ref:`sd_pullup_no_pullups`.
|
|
|
|
- ESP32-WROVER-B Series:
|
|
Including ESP32-WROVER-B and ESP32-WROVER-IB.
|
|
|
|
:ref:`sd_pullup_no_pullups`, :ref:`strapping_conflicts_dat2`.
|
|
|
|
.. _sdio_dev_kits:
|
|
|
|
Development Boards
|
|
^^^^^^^^^^^^^^^^^^
|
|
|
|
- ESP32-PICO-KIT:
|
|
Including PICO-KIT v4.1, v4.0 and v3.
|
|
|
|
:ref:`sd_pullup_no_pullups`, :ref:`strapping_conflicts_dat2`,
|
|
:ref:`gpio2_strapping_pin`.
|
|
|
|
- ESP32-DevKitC:
|
|
Including ESP32-DevKitC v4 and v2.
|
|
|
|
:ref:`sd_pullup_no_pullups`, :ref:`strapping_conflicts_dat2`,
|
|
:ref:`gpio2_strapping_pin`.
|
|
|
|
- ESP-WROVER-KIT:
|
|
v4.1: Have pullups, but :ref:`pullup_conflicts_on_gpio13` ,
|
|
:ref:`strapping_conflicts_dat2`.
|
|
|
|
v3: Have pullups, but :ref:`pullup_conflicts_on_gpio13`.
|
|
|
|
v2 and v1: Have pullups, but :ref:`pullup_conflicts_on_gpio13`,
|
|
:ref:`strapping_conflicts_dat2`, :ref:`gpio2_strapping_pin`.
|
|
|
|
You can tell the version of your ESP23-WROVER-KIT version from the module
|
|
on it: v4.1 are with ESP32-WROVER-B modules, v3 are with ESP32-WROVER
|
|
modules, while v2 and v1 are with ESP32-WROOM-32 modules.
|
|
|
|
- ESP32-LyraTD-MSC:
|
|
:ref:`strapping_conflicts_dat2`. Have pullups.
|
|
|
|
- ESP32-LyraT:
|
|
Have pullups, but :ref:`pullup_conflicts_on_gpio13`
|
|
|
|
Non-Espressif Hosts
|
|
^^^^^^^^^^^^^^^^^^^
|
|
|
|
Please make sure that your 3rd party SDIO host has correct pullups for all
|
|
the signals.
|
|
|
|
Solutions
|
|
---------
|
|
|
|
.. _sd_pullup_no_pullups:
|
|
|
|
No Pullups
|
|
^^^^^^^^^^
|
|
|
|
When developing on boards without pullups, you can either:
|
|
|
|
1. If your host and slave are on seperated boards, you can change one of them
|
|
to a board with pullups. Please see :ref:`sdio_dev_kits` to find Espressif
|
|
official boards with pullups.
|
|
2. Connect external pullups to VDD by yourself. Connect these pins without
|
|
pullups to the VDD through a 10 kOhm resistor.
|
|
|
|
.. _pullup_conflicts_on_gpio13:
|
|
|
|
Pullup Conflicts on GPIO13
|
|
^^^^^^^^^^^^^^^^^^^^^^^^^^
|
|
|
|
The DAT3 of slave may not be properly pulled up. You can either:
|
|
|
|
1. Use 1-bit mode, and tie DAT3 of slave to VDD.
|
|
2. Use SPI mode.
|
|
3. Remove the pulldown resistors on GPIO13; or pull it up by resistor less
|
|
than 5 kOhm (2 kOhm suggested); or pull it up or drive it high by host or
|
|
VDD3.3V in 1-bit mode.
|
|
|
|
.. _strapping_conflicts_dat2:
|
|
|
|
Conflicts Between Bootstrap and SDIO on DAT2
|
|
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
|
|
|
The strapping requirements conflict with SDIO protocol. See
|
|
:ref:`mtdi_strapping_pin` for the details of this issue. You can either:
|
|
|
|
1. (Recomended) Burn the flash voltage selection eFuses. This will
|
|
permanently select 3.3 V output voltage for the internal regulator, and GPIO12
|
|
will not be used as a bootstrapping pin. Then connect a pullup resistor
|
|
to GPIO12.
|
|
|
|
.. warning:: Burning eFuse is irreversible. The issue list above may be
|
|
out of date. Do make sure the module you are burning is using a 3.3 V flash
|
|
according to the information on http://www.espressif.com/. If you burn the
|
|
3.3 V eFuses on an 1.8 V module, the module will get broken.
|
|
|
|
Run the command below under your IDF folder:
|
|
::
|
|
|
|
components/esptool_py/esptool/espefuse.py set_flash_voltage 3.3V
|
|
|
|
This command will burn the `XPD_SDIO_TIEH`, `XPD_SDIO_FORCE`, and
|
|
`XPD_SDIO_REG` eFuses. With all three burned to value 1, the internal
|
|
VDD_SDIO flash voltage regulator is permanently set to 3.3 V. You will
|
|
see the following log if the burning succeeds:
|
|
::
|
|
|
|
espefuse.py v2.6
|
|
Connecting....
|
|
|
|
Enable internal flash voltage regulator (VDD_SDIO) to 3.3 V.
|
|
The following eFuses are burned: XPD_SDIO_FORCE, XPD_SDIO_REG, XPD_SDIO_TIEH.
|
|
This is an irreversible operation.
|
|
Type 'BURN' (all capitals) to continue.
|
|
BURN
|
|
VDD_SDIO setting complete.
|
|
|
|
You can also run ``components/esptool_py/esptool/espefuse.py summary`` to
|
|
check the status of the eFuses above.
|
|
|
|
`espefuse.py` has a ``--do-not-confirm`` option if running from an
|
|
automated flashing script.
|
|
|
|
See the ESP32 Technical Reference Manual for more details.
|
|
|
|
2. **When using 1-bit mode or SPI mode**, DAT2 signal is not needed (though it
|
|
still has to be pulled up). If the device works as the host, you can leave
|
|
the DAT2 of host floating, and directly connect DAT2 of slave to VDD; or if
|
|
the device works as the slave, specify ``SDIO_SLAVE_FLAG_DAT2_DISABLED`` in
|
|
the slave app to avoid slave detecting on DAT2 line. Note the host will
|
|
not know that 4-bit mode is not supported any more by the standard CCCR
|
|
register. You have to forbid the host from using 4-bit mode.
|
|
|
|
.. _no_pullup_on_gpio12:
|
|
|
|
No Pullup on GPIO12
|
|
^^^^^^^^^^^^^^^^^^^
|
|
|
|
Your module is compatible with the SDIO protocol. Just connect GPIO12 to the
|
|
VDD through a 10 kOhm resistor.
|
|
|
|
.. _gpio2_strapping_pin:
|
|
|
|
Auto-program Not Working (minor issue)
|
|
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
|
|
|
GPIO2 pin is used as a bootstrapping pin, and should be low to enter UART
|
|
download mode. You may find it unable to enter the UART download mode if you
|
|
correctly connect the pullup of SD on GPIO2.
|
|
|
|
Some official kits pull down GPIO2 when downloading. For other boards, you
|
|
may try to connect GPIO0 and GPIO2 using a jumper, and then the auto-reset
|
|
circuit on most development boards will pull GPIO2 low along with GPIO0, when
|
|
entering download mode. (Some boards have pulldown and/or LED on GPIO2. LED
|
|
is usually ok, but the pulldown resistor will interfere with D0 signals and
|
|
must be removed. Check the schematic of your development board for anything
|
|
connected to GPIO2.)
|
|
|
|
If the above way is not working, please just turn off the other device and
|
|
remove the pullups on GPIO2 when you are programming the slave.
|
|
|
|
|
|
.. _technical_detail_sdio:
|
|
|
|
Technical Details
|
|
-----------------
|
|
|
|
.. _mtdi_strapping_pin:
|
|
|
|
MTDI Strapping Pin
|
|
^^^^^^^^^^^^^^^^^^
|
|
|
|
MTDI (GPIO12) is used as a bootstrapping pin to select output voltage of an
|
|
internal regulator which powers the flash chip (VDD_SDIO). This pin has an
|
|
internal pulldown so if left unconnected it will read low at startup
|
|
(selecting default 3.3 V operation).
|
|
|
|
For ESP32-WROVER modules, excluding ESP32-WROVER-B, they use 1.8 V flash, and
|
|
have pullup on GPIO12 inside. For other modules, which use 3.3 V flash, have
|
|
no pullups on GPIO12, and GPIO12 is weakly pulled down internally.
|
|
|
|
When adding a pullup to this pin for SD card operation, consider the
|
|
following:
|
|
|
|
- For boards which don't use the internal regulator (VDD_SDIO) to power the
|
|
flash, GPIO12 can be pulled high.
|
|
- For boards which use 1.8 V flash chip, GPIO12 needs to be pulled high at
|
|
reset. This is fully compatible with SD card operation.
|
|
- On boards which use the internal regulator and a 3.3 V flash chip, GPIO12
|
|
must be low at reset. This is incompatible with SD card operation. Please
|
|
check :ref:`existing_issues_official_modules_sdio` to see whether your board
|
|
has this issue, and how to solve it.
|
|
|
|
Internal Pullups and Strapping Requirements
|
|
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
|
|
|
It is never recommended to rely on internal weak pullups for SDIO
|
|
communications, since internal weak pullups are insufficient. But information
|
|
of the strapping requirements and internal pullups may be useful. For
|
|
Espressif official modules, different weak pullups / pulldowns are connected
|
|
to CMD, and DATA pins as below.
|
|
|
|
+-----------------------+-----+--------------------------+------+-----------------------+------+
|
|
| GPIO | 15 | 2 | 4 | 12 | 13 |
|
|
+=======================+=====+==========================+======+=======================+======+
|
|
| Name | CMD | DAT0 | DAT1 | DAT2 | DAT3 |
|
|
+-----------------------+-----+--------------------------+------+-----------------------+------+
|
|
| At startup | WPU | WPD | WPD | PU for 1.8 V flash; | WPU |
|
|
| | | | | WPD for 3.3 V flash | |
|
|
+-----------------------+-----+--------------------------+------+-----------------------+------+
|
|
| Strapping requirement | | Low to download to flash | | High for 1.8 V flash; | |
|
|
| | | | | Low for 3.3 V flash | |
|
|
+-----------------------+-----+--------------------------+------+-----------------------+------+
|
|
|
|
- WPU: Weak pullup
|
|
- WPD: Weak pulldown
|
|
- PU: Pullup inside the module |