OVMS3-idf/examples/system/ulp/main/ulp_example_main.c
Ivan Grokhotkov 4b97a1edb2 ulp example: fix for RTC IOs
- call rtc_gpio_init for pins which aren't configured as RTC by default
- for RTC IOs 16 and 17, read higher part of the input register
- automatically convert GPIO number into RTC IO number
- use ulp_set_wakeup_period instead of writing to register
2018-07-13 17:48:15 +08:00

119 lines
4.1 KiB
C

/* ULP Example
This example code is in the Public Domain (or CC0 licensed, at your option.)
Unless required by applicable law or agreed to in writing, this
software is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR
CONDITIONS OF ANY KIND, either express or implied.
*/
#include <stdio.h>
#include "esp_sleep.h"
#include "nvs.h"
#include "nvs_flash.h"
#include "soc/rtc_cntl_reg.h"
#include "soc/sens_reg.h"
#include "soc/rtc_periph.h"
#include "driver/gpio.h"
#include "driver/rtc_io.h"
#include "esp32/ulp.h"
#include "ulp_main.h"
extern const uint8_t ulp_main_bin_start[] asm("_binary_ulp_main_bin_start");
extern const uint8_t ulp_main_bin_end[] asm("_binary_ulp_main_bin_end");
static void init_ulp_program();
static void update_pulse_count();
void app_main()
{
esp_sleep_wakeup_cause_t cause = esp_sleep_get_wakeup_cause();
if (cause != ESP_SLEEP_WAKEUP_ULP) {
printf("Not ULP wakeup, initializing ULP\n");
init_ulp_program();
} else {
printf("ULP wakeup, saving pulse count\n");
update_pulse_count();
}
printf("Entering deep sleep\n\n");
ESP_ERROR_CHECK( esp_sleep_enable_ulp_wakeup() );
esp_deep_sleep_start();
}
static void init_ulp_program()
{
esp_err_t err = ulp_load_binary(0, ulp_main_bin_start,
(ulp_main_bin_end - ulp_main_bin_start) / sizeof(uint32_t));
ESP_ERROR_CHECK(err);
/* GPIO used for pulse counting. */
gpio_num_t gpio_num = GPIO_NUM_0;
assert(rtc_gpio_desc[gpio_num].reg && "GPIO used for pulse counting must be an RTC IO");
/* Initialize some variables used by ULP program.
* Each 'ulp_xyz' variable corresponds to 'xyz' variable in the ULP program.
* These variables are declared in an auto generated header file,
* 'ulp_main.h', name of this file is defined in component.mk as ULP_APP_NAME.
* These variables are located in RTC_SLOW_MEM and can be accessed both by the
* ULP and the main CPUs.
*
* Note that the ULP reads only the lower 16 bits of these variables.
*/
ulp_debounce_counter = 3;
ulp_debounce_max_count = 3;
ulp_next_edge = 0;
ulp_io_number = rtc_gpio_desc[gpio_num].rtc_num; /* map from GPIO# to RTC_IO# */
ulp_edge_count_to_wake_up = 10;
/* Initialize selected GPIO as RTC IO, enable input, disable pullup and pulldown */
rtc_gpio_init(gpio_num);
rtc_gpio_set_direction(gpio_num, RTC_GPIO_MODE_INPUT_ONLY);
rtc_gpio_pulldown_dis(gpio_num);
rtc_gpio_pullup_dis(gpio_num);
rtc_gpio_hold_en(gpio_num);
/* Disconnect GPIO12 and GPIO15 to remove current drain through
* pullup/pulldown resistors.
* GPIO15 may be connected to ground to suppress boot messages.
* GPIO12 may be pulled high to select flash voltage.
*/
rtc_gpio_isolate(GPIO_NUM_12);
rtc_gpio_isolate(GPIO_NUM_15);
/* Set ULP wake up period to T = 20ms.
* Minimum pulse width has to be T * (ulp_debounce_counter + 1) = 80ms.
*/
ulp_set_wakeup_period(0, 20000);
/* Start the program */
err = ulp_run((&ulp_entry - RTC_SLOW_MEM) / sizeof(uint32_t));
ESP_ERROR_CHECK(err);
}
static void update_pulse_count()
{
const char* namespace = "plusecnt";
const char* count_key = "count";
ESP_ERROR_CHECK( nvs_flash_init() );
nvs_handle handle;
ESP_ERROR_CHECK( nvs_open(namespace, NVS_READWRITE, &handle));
uint32_t pulse_count = 0;
esp_err_t err = nvs_get_u32(handle, count_key, &pulse_count);
assert(err == ESP_OK || err == ESP_ERR_NVS_NOT_FOUND);
printf("Read pulse count from NVS: %5d\n", pulse_count);
/* ULP program counts signal edges, convert that to the number of pulses */
uint32_t pulse_count_from_ulp = (ulp_edge_count & UINT16_MAX) / 2;
/* In case of an odd number of edges, keep one until next time */
ulp_edge_count = ulp_edge_count % 2;
printf("Pulse count from ULP: %5d\n", pulse_count_from_ulp);
/* Save the new pulse count to NVS */
pulse_count += pulse_count_from_ulp;
ESP_ERROR_CHECK(nvs_set_u32(handle, count_key, pulse_count));
ESP_ERROR_CHECK(nvs_commit(handle));
nvs_close(handle);
printf("Wrote updated pulse count to NVS: %5d\n", pulse_count);
}