OVMS3-idf/examples/protocols/modbus_slave/main/freemodbus.c
aleks 5379c941b8 examples: freemodbus port serial slave move uart mode settings into example
Update freemodbus component file esp-idf/components/freemodbus/port/portserial.c to remove UART mode settings;
Move UART mode settings into esp-idf/examples/protocols/modbus_slave/main/freemodbus.c
Move UART pin settings from Component config into example Kconfig.projbuild file
Move setup of UART port pins from freemodbus component into example file

TW#27721
Closes https://github.com/espressif/esp-idf/issues/2784#issuecomment-443600157
2018-12-19 08:03:18 +00:00

176 lines
8.3 KiB
C

/* FreeModbus Slave Example ESP32
Unless required by applicable law or agreed to in writing, this
software is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR
CONDITIONS OF ANY KIND, either express or implied.
*/
#include <stdio.h>
#include "esp_err.h"
#include "sdkconfig.h"
#include "mbcontroller.h" // for mbcontroller defines and api
#include "deviceparams.h" // for device parameters structures
#include "esp_log.h" // for log_write
#define MB_PORT_NUM (2) // Number of UART port used for Modbus connection
#define MB_DEV_ADDR (1) // The address of device in Modbus network
#define MB_DEV_SPEED (115200) // The communication speed of the UART
// Defines below are used to define register start address for each type of Modbus registers
#define MB_REG_DISCRETE_INPUT_START (0x0000)
#define MB_REG_INPUT_START (0x0000)
#define MB_REG_HOLDING_START (0x0000)
#define MB_REG_COILS_START (0x0000)
#define MB_PAR_INFO_GET_TOUT (10) // Timeout for get parameter info
#define MB_CHAN_DATA_MAX_VAL (10)
#define MB_CHAN_DATA_OFFSET (0.01f)
static const char *TAG = "MODBUS_SLAVE_APP";
// Set register values into known state
static void setup_reg_data()
{
// Define initial state of parameters
discrete_reg_params.discrete_input1 = 1;
discrete_reg_params.discrete_input3 = 1;
discrete_reg_params.discrete_input5 = 1;
discrete_reg_params.discrete_input7 = 1;
holding_reg_params.data_chan0 = 1.34;
holding_reg_params.data_chan1 = 2.56;
holding_reg_params.data_chan2 = 3.78;
holding_reg_params.data_chan3 = 4.90;
coil_reg_params.coil0 = 1;
coil_reg_params.coil2 = 1;
coil_reg_params.coil4 = 1;
coil_reg_params.coil6 = 1;
coil_reg_params.coil7 = 1;
input_reg_params.data_chan0 = 1.34;
input_reg_params.data_chan1 = 2.56;
input_reg_params.data_chan2 = 3.78;
input_reg_params.data_chan3 = 4.90;
}
// An example application of Modbus slave. It is based on freemodbus stack.
// See deviceparams.h file for more information about assigned Modbus parameters.
// These parameters can be accessed from main application and also can be changed
// by external Modbus master host.
void app_main()
{
mb_param_info_t reg_info; // keeps the Modbus registers access information
mb_communication_info_t comm_info; // Modbus communication parameters
mb_register_area_descriptor_t reg_area; // Modbus register area descriptor structure
// Set UART log level
esp_log_level_set(TAG, ESP_LOG_INFO);
mbcontroller_init(); // Initialization of Modbus controller
// Setup communication parameters and start stack
comm_info.mode = MB_MODE_RTU;
comm_info.slave_addr = MB_DEV_ADDR;
comm_info.port = MB_PORT_NUM;
comm_info.baudrate = MB_DEV_SPEED;
comm_info.parity = MB_PARITY_NONE;
ESP_ERROR_CHECK(mbcontroller_setup(comm_info));
// The code below initializes Modbus register area descriptors
// for Modbus Holding Registers, Input Registers, Coils and Discrete Inputs
// Initialization should be done for each supported Modbus register area according to register map.
// When external master trying to access the register in the area that is not initialized
// by mbcontroller_set_descriptor() API call then Modbus stack
// will send exception response for this register area.
reg_area.type = MB_PARAM_HOLDING; // Set type of register area
reg_area.start_offset = MB_REG_HOLDING_START; // Offset of register area in Modbus protocol
reg_area.address = (void*)&holding_reg_params; // Set pointer to storage instance
reg_area.size = sizeof(holding_reg_params); // Set the size of register storage instance
ESP_ERROR_CHECK(mbcontroller_set_descriptor(reg_area));
// Initialization of Input Registers area
reg_area.type = MB_PARAM_INPUT;
reg_area.start_offset = MB_REG_INPUT_START;
reg_area.address = (void*)&input_reg_params;
reg_area.size = sizeof(input_reg_params);
ESP_ERROR_CHECK(mbcontroller_set_descriptor(reg_area));
// Initialization of Coils register area
reg_area.type = MB_PARAM_COIL;
reg_area.start_offset = MB_REG_COILS_START;
reg_area.address = (void*)&coil_reg_params;
reg_area.size = sizeof(coil_reg_params);
ESP_ERROR_CHECK(mbcontroller_set_descriptor(reg_area));
// Initialization of Discrete Inputs register area
reg_area.type = MB_PARAM_DISCRETE;
reg_area.start_offset = MB_REG_DISCRETE_INPUT_START;
reg_area.address = (void*)&discrete_reg_params;
reg_area.size = sizeof(discrete_reg_params);
ESP_ERROR_CHECK(mbcontroller_set_descriptor(reg_area));
setup_reg_data(); // Set values into known state
// Starts of modbus controller and stack
ESP_ERROR_CHECK(mbcontroller_start());
// Set UART driver mode to Half Duplex
ESP_ERROR_CHECK(uart_set_mode(MB_PORT_NUM, UART_MODE_RS485_HALF_DUPLEX));
// Set UART pin numbers
ESP_ERROR_CHECK(uart_set_pin(MB_PORT_NUM, CONFIG_MB_UART_TXD,
CONFIG_MB_UART_RXD, CONFIG_MB_UART_RTS,
UART_PIN_NO_CHANGE));
// The cycle below will be terminated when parameter holdingRegParams.dataChan0
// incremented each access cycle reaches the CHAN_DATA_MAX_VAL value.
for(;holding_reg_params.data_chan0 < MB_CHAN_DATA_MAX_VAL;){
// Check for read/write events of Modbus master for certain events
mb_event_group_t event = mbcontroller_check_event((MB_EVENT_HOLDING_REG_WR
| MB_EVENT_INPUT_REG_RD
| MB_EVENT_HOLDING_REG_RD
| MB_EVENT_DISCRETE_RD));
// Filter events and process them accordingly
if((event & MB_EVENT_HOLDING_REG_WR) || (event & MB_EVENT_HOLDING_REG_RD)) {
// Get parameter information from parameter queue
ESP_ERROR_CHECK(mbcontroller_get_param_info(&reg_info, MB_PAR_INFO_GET_TOUT));
printf("HOLDING READ/WRITE: time_stamp(us):%u, mb_addr:%u, type:%u, st_address:0x%.4x, size:%u\r\n",
(uint32_t)reg_info.time_stamp,
(uint32_t)reg_info.mb_offset,
(uint32_t)reg_info.type,
(uint32_t)reg_info.address,
(uint32_t)reg_info.size);
if (reg_info.address == (uint8_t*)&holding_reg_params.data_chan0)
{
holding_reg_params.data_chan0 += MB_CHAN_DATA_OFFSET;
}
} else if (event & MB_EVENT_INPUT_REG_RD) {
ESP_ERROR_CHECK(mbcontroller_get_param_info(&reg_info, MB_PAR_INFO_GET_TOUT));
printf("INPUT READ: time_stamp(us):%u, mb_addr:%u, type:%u, st_address:0x%.4x, size:%u\r\n",
(uint32_t)reg_info.time_stamp,
(uint32_t)reg_info.mb_offset,
(uint32_t)reg_info.type,
(uint32_t)reg_info.address,
(uint32_t)reg_info.size);
} else if (event & MB_EVENT_DISCRETE_RD) {
ESP_ERROR_CHECK(mbcontroller_get_param_info(&reg_info, MB_PAR_INFO_GET_TOUT));
printf("DISCRETE READ: time_stamp(us):%u, mb_addr:%u, type:%u, st_address:0x%.4x, size:%u\r\n",
(uint32_t)reg_info.time_stamp,
(uint32_t)reg_info.mb_offset,
(uint32_t)reg_info.type,
(uint32_t)reg_info.address,
(uint32_t)reg_info.size);
} else if (event & MB_EVENT_COILS_RD) {
ESP_ERROR_CHECK(mbcontroller_get_param_info(&reg_info, MB_PAR_INFO_GET_TOUT));
printf("COILS READ: time_stamp(us):%u, mb_addr:%u, type:%u, st_address:0x%.4x, size:%u\r\n",
(uint32_t)reg_info.time_stamp,
(uint32_t)reg_info.mb_offset,
(uint32_t)reg_info.type,
(uint32_t)reg_info.address,
(uint32_t)reg_info.size);
}
}
// Destroy of Modbus controller once get maximum value of data_chan0
printf("Modbus controller destroyed.");
ESP_ERROR_CHECK(mbcontroller_destroy());
}