OVMS3-idf/components/bt/host/bluedroid/common/include/common/bte.h
2019-06-30 16:39:00 +08:00

116 lines
4.6 KiB
C

/******************************************************************************
*
* Copyright (C) 2001-2012 Broadcom Corporation
*
* Licensed under the Apache License, Version 2.0 (the "License");
* you may not use this file except in compliance with the License.
* You may obtain a copy of the License at:
*
* http://www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS,
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
* See the License for the specific language governing permissions and
* limitations under the License.
*
******************************************************************************/
/******************************************************************************
*
* this file contains constants and definitions for the bte project
*
******************************************************************************/
#ifndef BTE_H
#define BTE_H
//#include <osi/semaphore.h>
//#include <signal.h>
//#include <pthread.h>
#include "common/bt_target.h"
/* by default on shutdown, baudrate is reset 115kbits. this should NOT be need for platforms
* that kill BTE driver and remove/reset BT chip
*/
#ifndef BTE_RESET_BAUD_ON_BT_DISABLE
#define BTE_RESET_BAUD_ON_BT_DISABLE TRUE
#endif
/* Target Modes (based on jumper settings on hardware [see user manual]) */
enum {
/* BTE BBY */
/* J3 J4 SW3-3 SW3-2 SW3-1 */
/* -------------------------------------------- */
BTE_MODE_SERIAL_APP, /* OUT OUT OFF OFF OFF Sample serial port application */
BTE_MODE_APPL, /* IN OUT OFF OFF ON Target used with Tester through RPC */
BTE_MODE_RESERVED, /* OUT IN OFF ON OFF Reserved */
BTE_MODE_SAMPLE_APPS, /* IN IN OFF ON ON Sample applications (ICP/HSP) */
BTE_MODE_DONGLE, /* not yet supported ON OFF OFF Dongle mode */
BTE_MODE_APPL_PROTOCOL_TRACE, /* this is a fake mode do allow protocol tracing in application without rpc */
BTE_MODE_INVALID
};
extern volatile UINT8 bte_target_mode; /* indicates the mode that the board is running in */
/* Startup options */
extern UINT32 bte_startup_options; /* Switch and jumper settings at startup */
void bte_get_startup_options(UINT32 *p_options); /* Platform specific function for getting startup options */
#define BTE_OPTIONS_TARGET_MODE_MASK 0x00000007 /* bits 2-0 indicate target mode (QuickConnect: jp3 & jp4, BBY: SW3-1 & SW3-2)*/
/****************************************************************************
* Definitions to define which type of application gets built
****************************************************************************/
#define BUILD_HCITOOL FALSE
#define BUILD_L2PING FALSE
#define LINUX_FM_DRIVER_INCLUDED FALSE
/* hcisu userial operations. should probably go into bt_types to avoid collisions! */
#define BT_EVT_TO_HCISU_USERIAL_OP (0x0080 | BT_EVT_HCISU)
/* operation for above hcisu event */
#define BT_HCISU_USERIAL_OPEN (0) /* open serial port calling USERIAL_Open() */
#define BT_HCISU_USERIAL_CLOSE (1) /* close userial port */
/* options associated with close op */
#define BT_HCISU_USERIAL_CL_NO_DIS_BT 0 /* do not touch bt_wake and power gpio */
#define BT_HCISU_USERIAL_CL_DIS_BT 1 /* put power and bt_wake into defined off state to preserve
power */
/* status codes for callback */
/*
#define BTE_HCISU_USERIAL_FAIL 0
#define BTE_HCISU_USERIAL_OK 1
typedef void (tUSERIAL_MSG_CBACK) (int status);
typedef struct tHCISU_USERIAL_MSG_tag {
BT_HDR hdr;
tUSERIAL_MSG_CBACK *p_cback;
UINT8 port; // port number
UINT8 op;
UINT8 option; // option for operation. depends on operation
} tHCISU_USERIAL_MSG;
extern void bte_hcisu_userial_oper( tUSERIAL_MSG_CBACK *p_cback, UINT8 port, UINT8 op, UINT8 option );
*/
/* Pointer to function for sending HCI commands and data to the HCI tranport */
extern int (*p_bte_hci_send)(UINT16 port, BT_HDR *p_msg);
/* Protocol trace mask */
extern UINT32 bte_proto_trace_mask;
typedef struct tBAUD_REG_tag {
UINT8 DHBR;
UINT8 DLBR;
UINT8 ExplicitBaudRate0;
UINT8 ExplicitBaudRate1;
UINT8 ExplicitBaudRate2;
UINT8 ExplicitBaudRate3;
} tBAUD_REG;
extern const tBAUD_REG baud_rate_regs[];
#endif /* BTE_H */