OVMS3-idf/examples/protocols/modbus/serial/mb_master/main/master.c
Alex Lisitsyn 16e6e63694 driver: fix driver set rx timeout feature of uart
tout_thr - move calculation and masking into hal layer update driver and uart_ll (add uart_ll_set_rx_tout)
move tout calculation into uart_ll
move calculation of time out in bit time for esp32s2 into low level uart_ll.h file
move uart_hal_get_symb_len() into hal
update set_rx_timeout() to warn user about incorrect value
update HAL, LL 1
fix uart_xx_set_rx_tout() to convert symbol time into bit time
update param description
update tout calculation in LL
update uart_hal_get_max_rx_timeout_thrd() and uart_ll_get_max_rx_timeout_thrd()
2020-03-27 16:20:21 +08:00

276 lines
13 KiB
C

// Copyright 2016-2019 Espressif Systems (Shanghai) PTE LTD
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
//
// http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
#include "string.h"
#include "esp_log.h"
#include "modbus_params.h" // for modbus parameters structures
#include "mbcontroller.h"
#include "sdkconfig.h"
#define MB_PORT_NUM (CONFIG_MB_UART_PORT_NUM) // Number of UART port used for Modbus connection
#define MB_DEV_SPEED (CONFIG_MB_UART_BAUD_RATE) // The communication speed of the UART
// Note: Some pins on target chip cannot be assigned for UART communication.
// See UART documentation for selected board and target to configure pins using Kconfig.
// The number of parameters that intended to be used in the particular control process
#define MASTER_MAX_CIDS num_device_parameters
// Number of reading of parameters from slave
#define MASTER_MAX_RETRY 30
// Timeout to update cid over Modbus
#define UPDATE_CIDS_TIMEOUT_MS (500)
#define UPDATE_CIDS_TIMEOUT_TICS (UPDATE_CIDS_TIMEOUT_MS / portTICK_RATE_MS)
// Timeout between polls
#define POLL_TIMEOUT_MS (1)
#define POLL_TIMEOUT_TICS (POLL_TIMEOUT_MS / portTICK_RATE_MS)
#define MASTER_TAG "MASTER_TEST"
#define MASTER_CHECK(a, ret_val, str, ...) \
if (!(a)) { \
ESP_LOGE(MASTER_TAG, "%s(%u): " str, __FUNCTION__, __LINE__, ##__VA_ARGS__); \
return (ret_val); \
}
// The macro to get offset for parameter in the appropriate structure
#define HOLD_OFFSET(field) ((uint16_t)(offsetof(holding_reg_params_t, field) + 1))
#define INPUT_OFFSET(field) ((uint16_t)(offsetof(input_reg_params_t, field) + 1))
#define COIL_OFFSET(field) ((uint16_t)(offsetof(coil_reg_params_t, field) + 1))
// Discrete offset macro
#define DISCR_OFFSET(field) ((uint16_t)(offsetof(discrete_reg_params_t, field) + 1))
#define STR(fieldname) ((const char*)( fieldname ))
// Options can be used as bit masks or parameter limits
#define OPTS(min_val, max_val, step_val) { .opt1 = min_val, .opt2 = max_val, .opt3 = step_val }
// Enumeration of modbus device addresses accessed by master device
enum {
MB_DEVICE_ADDR1 = 1 // Only one slave device used for the test (add other slave addresses here)
};
// Enumeration of all supported CIDs for device (used in parameter definition table)
enum {
CID_INP_DATA_0 = 0,
CID_HOLD_DATA_0,
CID_INP_DATA_1,
CID_HOLD_DATA_1,
CID_INP_DATA_2,
CID_HOLD_DATA_2,
CID_RELAY_P1,
CID_RELAY_P2,
CID_COUNT
};
// Example Data (Object) Dictionary for Modbus parameters:
// The CID field in the table must be unique.
// Modbus Slave Addr field defines slave address of the device with correspond parameter.
// Modbus Reg Type - Type of Modbus register area (Holding register, Input Register and such).
// Reg Start field defines the start Modbus register number and Reg Size defines the number of registers for the characteristic accordingly.
// The Instance Offset defines offset in the appropriate parameter structure that will be used as instance to save parameter value.
// Data Type, Data Size specify type of the characteristic and its data size.
// Parameter Options field specifies the options that can be used to process parameter value (limits or masks).
// Access Mode - can be used to implement custom options for processing of characteristic (Read/Write restrictions, factory mode values and etc).
const mb_parameter_descriptor_t device_parameters[] = {
// { CID, Param Name, Units, Modbus Slave Addr, Modbus Reg Type, Reg Start, Reg Size, Instance Offset, Data Type, Data Size, Parameter Options, Access Mode}
{ CID_INP_DATA_0, STR("Data_channel_0"), STR("Volts"), MB_DEVICE_ADDR1, MB_PARAM_INPUT, 0, 2,
INPUT_OFFSET(input_data0), PARAM_TYPE_FLOAT, 4, OPTS( -10, 10, 1 ), PAR_PERMS_READ_WRITE_TRIGGER },
{ CID_HOLD_DATA_0, STR("Humidity_1"), STR("%rH"), MB_DEVICE_ADDR1, MB_PARAM_HOLDING, 0, 2,
HOLD_OFFSET(holding_data0), PARAM_TYPE_FLOAT, 4, OPTS( 0, 100, 1 ), PAR_PERMS_READ_WRITE_TRIGGER },
{ CID_INP_DATA_1, STR("Temperature_1"), STR("C"), MB_DEVICE_ADDR1, MB_PARAM_INPUT, 2, 2,
INPUT_OFFSET(input_data1), PARAM_TYPE_FLOAT, 4, OPTS( -40, 100, 1 ), PAR_PERMS_READ_WRITE_TRIGGER },
{ CID_HOLD_DATA_1, STR("Humidity_2"), STR("%rH"), MB_DEVICE_ADDR1, MB_PARAM_HOLDING, 2, 2,
HOLD_OFFSET(holding_data1), PARAM_TYPE_FLOAT, 4, OPTS( 0, 100, 1 ), PAR_PERMS_READ_WRITE_TRIGGER },
{ CID_INP_DATA_2, STR("Temperature_2"), STR("C"), MB_DEVICE_ADDR1, MB_PARAM_INPUT, 4, 2,
INPUT_OFFSET(input_data2), PARAM_TYPE_FLOAT, 4, OPTS( -40, 100, 1 ), PAR_PERMS_READ_WRITE_TRIGGER },
{ CID_HOLD_DATA_2, STR("Humidity_3"), STR("%rH"), MB_DEVICE_ADDR1, MB_PARAM_HOLDING, 4, 2,
HOLD_OFFSET(holding_data2), PARAM_TYPE_FLOAT, 4, OPTS( 0, 100, 1 ), PAR_PERMS_READ_WRITE_TRIGGER },
{ CID_RELAY_P1, STR("RelayP1"), STR("on/off"), MB_DEVICE_ADDR1, MB_PARAM_COIL, 0, 8,
COIL_OFFSET(coils_port0), PARAM_TYPE_U16, 2, OPTS( BIT1, 0, 0 ), PAR_PERMS_READ_WRITE_TRIGGER },
{ CID_RELAY_P2, STR("RelayP2"), STR("on/off"), MB_DEVICE_ADDR1, MB_PARAM_COIL, 8, 8,
COIL_OFFSET(coils_port1), PARAM_TYPE_U16, 2, OPTS( BIT0, 0, 0 ), PAR_PERMS_READ_WRITE_TRIGGER }
};
// Calculate number of parameters in the table
const uint16_t num_device_parameters = (sizeof(device_parameters)/sizeof(device_parameters[0]));
// The function to get pointer to parameter storage (instance) according to parameter description table
static void* master_get_param_data(const mb_parameter_descriptor_t* param_descriptor)
{
assert(param_descriptor != NULL);
void* instance_ptr = NULL;
if (param_descriptor->param_offset != 0) {
switch(param_descriptor->mb_param_type)
{
case MB_PARAM_HOLDING:
instance_ptr = ((void*)&holding_reg_params + param_descriptor->param_offset - 1);
break;
case MB_PARAM_INPUT:
instance_ptr = ((void*)&input_reg_params + param_descriptor->param_offset - 1);
break;
case MB_PARAM_COIL:
instance_ptr = ((void*)&coil_reg_params + param_descriptor->param_offset - 1);
break;
case MB_PARAM_DISCRETE:
instance_ptr = ((void*)&discrete_reg_params + param_descriptor->param_offset - 1);
break;
default:
instance_ptr = NULL;
break;
}
} else {
ESP_LOGE(MASTER_TAG, "Wrong parameter offset for CID #%d", param_descriptor->cid);
assert(instance_ptr != NULL);
}
return instance_ptr;
}
// User operation function to read slave values and check alarm
static void master_operation_func(void *arg)
{
esp_err_t err = ESP_OK;
float value = 0;
bool alarm_state = false;
const mb_parameter_descriptor_t* param_descriptor = NULL;
ESP_LOGI(MASTER_TAG, "Start modbus test...");
for(uint16_t retry = 0; retry <= MASTER_MAX_RETRY && (!alarm_state); retry++) {
// Read all found characteristics from slave(s)
for (uint16_t cid = 0; (err != ESP_ERR_NOT_FOUND) && cid < MASTER_MAX_CIDS; cid++)
{
// Get data from parameters description table
// and use this information to fill the characteristics description table
// and having all required fields in just one table
err = mbc_master_get_cid_info(cid, &param_descriptor);
if ((err != ESP_ERR_NOT_FOUND) && (param_descriptor != NULL)) {
void* temp_data_ptr = master_get_param_data(param_descriptor);
assert(temp_data_ptr);
uint8_t type = 0;
err = mbc_master_get_parameter(cid, (char*)param_descriptor->param_key,
(uint8_t*)&value, &type);
if (err == ESP_OK) {
*(float*)temp_data_ptr = value;
if ((param_descriptor->mb_param_type == MB_PARAM_HOLDING) ||
(param_descriptor->mb_param_type == MB_PARAM_INPUT)) {
ESP_LOGI(MASTER_TAG, "Characteristic #%d %s (%s) value = %f (0x%x) read successful.",
param_descriptor->cid,
(char*)param_descriptor->param_key,
(char*)param_descriptor->param_units,
value,
*(uint32_t*)temp_data_ptr);
if (((value > param_descriptor->param_opts.max) ||
(value < param_descriptor->param_opts.min))) {
alarm_state = true;
break;
}
} else {
uint16_t state = *(uint16_t*)temp_data_ptr;
const char* rw_str = (state & param_descriptor->param_opts.opt1) ? "ON" : "OFF";
ESP_LOGI(MASTER_TAG, "Characteristic #%d %s (%s) value = %s (0x%x) read successful.",
param_descriptor->cid,
(char*)param_descriptor->param_key,
(char*)param_descriptor->param_units,
(const char*)rw_str,
*(uint16_t*)temp_data_ptr);
if (state & param_descriptor->param_opts.opt1) {
alarm_state = true;
break;
}
}
} else {
ESP_LOGE(MASTER_TAG, "Characteristic #%d (%s) read fail, err = %d (%s).",
param_descriptor->cid,
(char*)param_descriptor->param_key,
(int)err,
(char*)esp_err_to_name(err));
}
vTaskDelay(POLL_TIMEOUT_TICS); // timeout between polls
}
}
vTaskDelay(UPDATE_CIDS_TIMEOUT_TICS); //
}
if (alarm_state) {
ESP_LOGI(MASTER_TAG, "Alarm triggered by cid #%d.",
param_descriptor->cid);
} else {
ESP_LOGE(MASTER_TAG, "Alarm is not triggered after %d retries.",
MASTER_MAX_RETRY);
}
ESP_LOGI(MASTER_TAG, "Destroy master...");
ESP_ERROR_CHECK(mbc_master_destroy());
}
// Modbus master initialization
static esp_err_t master_init(void)
{
// Initialize and start Modbus controller
mb_communication_info_t comm = {
.port = MB_PORT_NUM,
#if CONFIG_MB_COMM_MODE_ASCII
.mode = MB_MODE_ASCII,
#elif CONFIG_MB_COMM_MODE_RTU
.mode = MB_MODE_RTU,
#endif
.baudrate = MB_DEV_SPEED,
.parity = MB_PARITY_NONE
};
void* master_handler = NULL;
esp_err_t err = mbc_master_init(MB_PORT_SERIAL_MASTER, &master_handler);
MASTER_CHECK((master_handler != NULL), ESP_ERR_INVALID_STATE,
"mb controller initialization fail.");
MASTER_CHECK((err == ESP_OK), ESP_ERR_INVALID_STATE,
"mb controller initialization fail, returns(0x%x).",
(uint32_t)err);
err = mbc_master_setup((void*)&comm);
MASTER_CHECK((err == ESP_OK), ESP_ERR_INVALID_STATE,
"mb controller setup fail, returns(0x%x).",
(uint32_t)err);
// Set UART pin numbers
err = uart_set_pin(MB_PORT_NUM, CONFIG_MB_UART_TXD, CONFIG_MB_UART_RXD,
CONFIG_MB_UART_RTS, UART_PIN_NO_CHANGE);
err = mbc_master_start();
MASTER_CHECK((err == ESP_OK), ESP_ERR_INVALID_STATE,
"mb controller start fail, returns(0x%x).",
(uint32_t)err);
MASTER_CHECK((err == ESP_OK), ESP_ERR_INVALID_STATE,
"mb serial set pin failure, uart_set_pin() returned (0x%x).", (uint32_t)err);
// Set driver mode to Half Duplex
err = uart_set_mode(MB_PORT_NUM, UART_MODE_RS485_HALF_DUPLEX);
MASTER_CHECK((err == ESP_OK), ESP_ERR_INVALID_STATE,
"mb serial set mode failure, uart_set_mode() returned (0x%x).", (uint32_t)err);
vTaskDelay(5);
err = mbc_master_set_descriptor(&device_parameters[0], num_device_parameters);
MASTER_CHECK((err == ESP_OK), ESP_ERR_INVALID_STATE,
"mb controller set descriptor fail, returns(0x%x).",
(uint32_t)err);
ESP_LOGI(MASTER_TAG, "Modbus master stack initialized...");
return err;
}
void app_main(void)
{
// Initialization of device peripheral and objects
ESP_ERROR_CHECK(master_init());
vTaskDelay(10);
master_operation_func(NULL);
}