1399 lines
86 KiB
C
1399 lines
86 KiB
C
// Copyright 2015-2016 Espressif Systems (Shanghai) PTE LTD
|
||
//
|
||
// Licensed under the Apache License, Version 2.0 (the "License");
|
||
// you may not use this file except in compliance with the License.
|
||
// You may obtain a copy of the License at
|
||
|
||
// http://www.apache.org/licenses/LICENSE-2.0
|
||
//
|
||
// Unless required by applicable law or agreed to in writing, software
|
||
// distributed under the License is distributed on an "AS IS" BASIS,
|
||
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
||
// See the License for the specific language governing permissions and
|
||
// limitations under the License.
|
||
#ifndef _SOC_UART_REG_H_
|
||
#define _SOC_UART_REG_H_
|
||
|
||
#include "soc.h"
|
||
|
||
//Slow bus
|
||
//#define REG_UART_BASE( i ) (0x60000000+(i)*0x10000)
|
||
//Fast bus
|
||
#define REG_UART_BASE( i ) (0x3ff40000+(i)*0x10000)
|
||
|
||
#define UART_FIFO_REG(i) (REG_UART_BASE(i) + 0x0)
|
||
/* UART_RXFIFO_RD_BYTE : RO ;bitpos:[7:0] ;default: 8'b0 ; */
|
||
/*description: R/W share the same address*/
|
||
#define UART_RXFIFO_RD_BYTE 0x000000FF
|
||
#define UART_RXFIFO_RD_BYTE_M ((UART_RXFIFO_RD_BYTE_V)<<(UART_RXFIFO_RD_BYTE_S))
|
||
#define UART_RXFIFO_RD_BYTE_V 0xFF
|
||
#define UART_RXFIFO_RD_BYTE_S 0
|
||
#define UART_GET_RXFIFO_RD_BYTE(i) GET_PERI_REG_BITS2(UART_FIFO_REG(i) , UART_RXFIFO_RD_BYTE_V, UART_RXFIFO_RD_BYTE_S)
|
||
#define UART_SET_TXFIFO_WR_BYTE(i,val) SET_PERI_REG_BITS(UART_FIFO_REG(i) , UART_RXFIFO_RD_BYTE_V, val, UART_RXFIFO_RD_BYTE_S)
|
||
|
||
|
||
|
||
#define UART_INT_RAW_REG(i) (REG_UART_BASE(i) + 0x4)
|
||
/* UART_AT_CMD_CHAR_DET_INT_RAW : RO ;bitpos:[18] ;default: 1'b0 ; */
|
||
/*description: The interrupt raw bit for detecting AT_CMD char interrupt*/
|
||
#define UART_AT_CMD_CHAR_DET_INT_RAW (BIT(18))
|
||
#define UART_AT_CMD_CHAR_DET_INT_RAW_M (BIT(18))
|
||
#define UART_AT_CMD_CHAR_DET_INT_RAW_V 0x1
|
||
#define UART_AT_CMD_CHAR_DET_INT_RAW_S 18
|
||
/* UART_RS485_CLASH_INT_RAW : RO ;bitpos:[17] ;default: 1'b0 ; */
|
||
/*description: The interrupt raw bit for rs485 tx rx clash interrrupt*/
|
||
#define UART_RS485_CLASH_INT_RAW (BIT(17))
|
||
#define UART_RS485_CLASH_INT_RAW_M (BIT(17))
|
||
#define UART_RS485_CLASH_INT_RAW_V 0x1
|
||
#define UART_RS485_CLASH_INT_RAW_S 17
|
||
/* UART_RS485_FRM_ERR_INT_RAW : RO ;bitpos:[16] ;default: 1'b0 ; */
|
||
/*description: The interrupt raw bit for rs485 other rx error*/
|
||
#define UART_RS485_FRM_ERR_INT_RAW (BIT(16))
|
||
#define UART_RS485_FRM_ERR_INT_RAW_M (BIT(16))
|
||
#define UART_RS485_FRM_ERR_INT_RAW_V 0x1
|
||
#define UART_RS485_FRM_ERR_INT_RAW_S 16
|
||
/* UART_RS485_PARITY_ERR_INT_RAW : RO ;bitpos:[15] ;default: 1'b0 ; */
|
||
/*description: The interrupt raw bit for rs485 parity error*/
|
||
#define UART_RS485_PARITY_ERR_INT_RAW (BIT(15))
|
||
#define UART_RS485_PARITY_ERR_INT_RAW_M (BIT(15))
|
||
#define UART_RS485_PARITY_ERR_INT_RAW_V 0x1
|
||
#define UART_RS485_PARITY_ERR_INT_RAW_S 15
|
||
/* UART_TX_DONE_INT_RAW : RO ;bitpos:[14] ;default: 1'b0 ; */
|
||
/*description: The interrupt raw bit for tx done*/
|
||
#define UART_TX_DONE_INT_RAW (BIT(14))
|
||
#define UART_TX_DONE_INT_RAW_M (BIT(14))
|
||
#define UART_TX_DONE_INT_RAW_V 0x1
|
||
#define UART_TX_DONE_INT_RAW_S 14
|
||
/* UART_TX_BRK_IDLE_DONE_INT_RAW : RO ;bitpos:[13] ;default: 1'b0 ; */
|
||
/*description: The interrupt raw bit for tx send idle done(depends on the uart_tx_idle_num)*/
|
||
#define UART_TX_BRK_IDLE_DONE_INT_RAW (BIT(13))
|
||
#define UART_TX_BRK_IDLE_DONE_INT_RAW_M (BIT(13))
|
||
#define UART_TX_BRK_IDLE_DONE_INT_RAW_V 0x1
|
||
#define UART_TX_BRK_IDLE_DONE_INT_RAW_S 13
|
||
/* UART_TX_BRK_DONE_INT_RAW : RO ;bitpos:[12] ;default: 1'b0 ; */
|
||
/*description: The interrupt raw bit for send 0 done(depends on uart_tx_brk_num)*/
|
||
#define UART_TX_BRK_DONE_INT_RAW (BIT(12))
|
||
#define UART_TX_BRK_DONE_INT_RAW_M (BIT(12))
|
||
#define UART_TX_BRK_DONE_INT_RAW_V 0x1
|
||
#define UART_TX_BRK_DONE_INT_RAW_S 12
|
||
/* UART_GLITCH_DET_INT_RAW : RO ;bitpos:[11] ;default: 1'b0 ; */
|
||
/*description: The interrupt raw bit for detecting rx glitch pulse*/
|
||
#define UART_GLITCH_DET_INT_RAW (BIT(11))
|
||
#define UART_GLITCH_DET_INT_RAW_M (BIT(11))
|
||
#define UART_GLITCH_DET_INT_RAW_V 0x1
|
||
#define UART_GLITCH_DET_INT_RAW_S 11
|
||
/* UART_SW_XOFF_INT_RAW : RO ;bitpos:[10] ;default: 1'b0 ; */
|
||
/*description: The interrupt raw bit for rx receive xoff char(depends on the uart_xoff_char )*/
|
||
#define UART_SW_XOFF_INT_RAW (BIT(10))
|
||
#define UART_SW_XOFF_INT_RAW_M (BIT(10))
|
||
#define UART_SW_XOFF_INT_RAW_V 0x1
|
||
#define UART_SW_XOFF_INT_RAW_S 10
|
||
/* UART_SW_XON_INT_RAW : RO ;bitpos:[9] ;default: 1'b0 ; */
|
||
/*description: The interrupt raw bit for rx receive xon char(depends on the uart_xon_char )*/
|
||
#define UART_SW_XON_INT_RAW (BIT(9))
|
||
#define UART_SW_XON_INT_RAW_M (BIT(9))
|
||
#define UART_SW_XON_INT_RAW_V 0x1
|
||
#define UART_SW_XON_INT_RAW_S 9
|
||
/* UART_RXFIFO_TOUT_INT_RAW : RO ;bitpos:[8] ;default: 1'b0 ; */
|
||
/*description: The interrupt raw bit for Rx time-out interrupt(depands on the UART_RX_TOUT_THRHD)*/
|
||
#define UART_RXFIFO_TOUT_INT_RAW (BIT(8))
|
||
#define UART_RXFIFO_TOUT_INT_RAW_M (BIT(8))
|
||
#define UART_RXFIFO_TOUT_INT_RAW_V 0x1
|
||
#define UART_RXFIFO_TOUT_INT_RAW_S 8
|
||
/* UART_BRK_DET_INT_RAW : RO ;bitpos:[7] ;default: 1'b0 ; */
|
||
/*description: The interrupt raw bit for Rx byte start error*/
|
||
#define UART_BRK_DET_INT_RAW (BIT(7))
|
||
#define UART_BRK_DET_INT_RAW_M (BIT(7))
|
||
#define UART_BRK_DET_INT_RAW_V 0x1
|
||
#define UART_BRK_DET_INT_RAW_S 7
|
||
/* UART_CTS_CHG_INT_RAW : RO ;bitpos:[6] ;default: 1'b0 ; */
|
||
/*description: The interrupt raw bit for CTS changing level*/
|
||
#define UART_CTS_CHG_INT_RAW (BIT(6))
|
||
#define UART_CTS_CHG_INT_RAW_M (BIT(6))
|
||
#define UART_CTS_CHG_INT_RAW_V 0x1
|
||
#define UART_CTS_CHG_INT_RAW_S 6
|
||
/* UART_DSR_CHG_INT_RAW : RO ;bitpos:[5] ;default: 1'b0 ; */
|
||
/*description: The interrupt raw bit for DSR changing level*/
|
||
#define UART_DSR_CHG_INT_RAW (BIT(5))
|
||
#define UART_DSR_CHG_INT_RAW_M (BIT(5))
|
||
#define UART_DSR_CHG_INT_RAW_V 0x1
|
||
#define UART_DSR_CHG_INT_RAW_S 5
|
||
/* UART_RXFIFO_OVF_INT_RAW : RO ;bitpos:[4] ;default: 1'b0 ; */
|
||
/*description: The interrupt raw bit for rx fifo overflow*/
|
||
#define UART_RXFIFO_OVF_INT_RAW (BIT(4))
|
||
#define UART_RXFIFO_OVF_INT_RAW_M (BIT(4))
|
||
#define UART_RXFIFO_OVF_INT_RAW_V 0x1
|
||
#define UART_RXFIFO_OVF_INT_RAW_S 4
|
||
/* UART_FRM_ERR_INT_RAW : RO ;bitpos:[3] ;default: 1'b0 ; */
|
||
/*description: The interrupt raw bit for other rx error*/
|
||
#define UART_FRM_ERR_INT_RAW (BIT(3))
|
||
#define UART_FRM_ERR_INT_RAW_M (BIT(3))
|
||
#define UART_FRM_ERR_INT_RAW_V 0x1
|
||
#define UART_FRM_ERR_INT_RAW_S 3
|
||
/* UART_PARITY_ERR_INT_RAW : RO ;bitpos:[2] ;default: 1'b0 ; */
|
||
/*description: The interrupt raw bit for parity check error*/
|
||
#define UART_PARITY_ERR_INT_RAW (BIT(2))
|
||
#define UART_PARITY_ERR_INT_RAW_M (BIT(2))
|
||
#define UART_PARITY_ERR_INT_RAW_V 0x1
|
||
#define UART_PARITY_ERR_INT_RAW_S 2
|
||
/* UART_TXFIFO_EMPTY_INT_RAW : RO ;bitpos:[1] ;default: 1'b0 ; */
|
||
/*description: The interrupt raw bit for tx fifo empty interrupt(depands on UART_TXFIFO_EMPTY_THRHD bits)*/
|
||
#define UART_TXFIFO_EMPTY_INT_RAW (BIT(1))
|
||
#define UART_TXFIFO_EMPTY_INT_RAW_M (BIT(1))
|
||
#define UART_TXFIFO_EMPTY_INT_RAW_V 0x1
|
||
#define UART_TXFIFO_EMPTY_INT_RAW_S 1
|
||
/* UART_RXFIFO_FULL_INT_RAW : RO ;bitpos:[0] ;default: 1'b0 ; */
|
||
/*description: The interrupt raw bit for rx fifo full interrupt(depands on UART_RXFIFO_FULL_THRHD bits)*/
|
||
#define UART_RXFIFO_FULL_INT_RAW (BIT(0))
|
||
#define UART_RXFIFO_FULL_INT_RAW_M (BIT(0))
|
||
#define UART_RXFIFO_FULL_INT_RAW_V 0x1
|
||
#define UART_RXFIFO_FULL_INT_RAW_S 0
|
||
#define UART_GET_AT_CMD_CHAR_DET_INT_RAW(i) GET_PERI_REG_BITS2(UART_INT_RAW_REG(i) , UART_AT_CMD_CHAR_DET_INT_RAW_V, UART_AT_CMD_CHAR_DET_INT_RAW_S)
|
||
#define UART_GET_RS485_CLASH_INT_RAW(i) GET_PERI_REG_BITS2(UART_INT_RAW_REG(i) , UART_RS485_CLASH_INT_RAW_V, UART_RS485_CLASH_INT_RAW_S)
|
||
#define UART_GET_RS485_FRM_ERR_INT_RAW(i) GET_PERI_REG_BITS2(UART_INT_RAW_REG(i) , UART_RS485_FRM_ERR_INT_RAW_V, UART_RS485_FRM_ERR_INT_RAW_S)
|
||
#define UART_GET_RS485_PARITY_ERR_INT_RAW(i) GET_PERI_REG_BITS2(UART_INT_RAW_REG(i) , UART_RS485_PARITY_ERR_INT_RAW_V, UART_RS485_PARITY_ERR_INT_RAW_S)
|
||
#define UART_GET_TX_DONE_INT_RAW(i) GET_PERI_REG_BITS2(UART_INT_RAW_REG(i) , UART_TX_DONE_INT_RAW_V, UART_TX_DONE_INT_RAW_S)
|
||
#define UART_GET_TX_BRK_IDLE_DONE_INT_RAW(i) GET_PERI_REG_BITS2(UART_INT_RAW_REG(i) , UART_TX_BRK_IDLE_DONE_INT_RAW_V, UART_TX_BRK_IDLE_DONE_INT_RAW_S)
|
||
#define UART_GET_TX_BRK_DONE_INT_RAW(i) GET_PERI_REG_BITS2(UART_INT_RAW_REG(i) , UART_TX_BRK_DONE_INT_RAW_V, UART_TX_BRK_DONE_INT_RAW_S)
|
||
#define UART_GET_GLITCH_DET_INT_RAW(i) GET_PERI_REG_BITS2(UART_INT_RAW_REG(i) , UART_GLITCH_DET_INT_RAW_V, UART_GLITCH_DET_INT_RAW_S)
|
||
#define UART_GET_SW_XOFF_INT_RAW(i) GET_PERI_REG_BITS2(UART_INT_RAW_REG(i) , UART_SW_XOFF_INT_RAW_V, UART_SW_XOFF_INT_RAW_S)
|
||
#define UART_GET_SW_XON_INT_RAW(i) GET_PERI_REG_BITS2(UART_INT_RAW_REG(i) , UART_SW_XON_INT_RAW_V, UART_SW_XON_INT_RAW_S)
|
||
#define UART_GET_RXFIFO_TOUT_INT_RAW(i) GET_PERI_REG_BITS2(UART_INT_RAW_REG(i) , UART_RXFIFO_TOUT_INT_RAW_V, UART_RXFIFO_TOUT_INT_RAW_S)
|
||
#define UART_GET_BRK_DET_INT_RAW(i) GET_PERI_REG_BITS2(UART_INT_RAW_REG(i) , UART_BRK_DET_INT_RAW_V, UART_BRK_DET_INT_RAW_S)
|
||
#define UART_GET_CTS_CHG_INT_RAW(i) GET_PERI_REG_BITS2(UART_INT_RAW_REG(i) , UART_CTS_CHG_INT_RAW_V, UART_CTS_CHG_INT_RAW_S)
|
||
#define UART_GET_DSR_CHG_INT_RAW(i) GET_PERI_REG_BITS2(UART_INT_RAW_REG(i) , UART_DSR_CHG_INT_RAW_V, UART_DSR_CHG_INT_RAW_S)
|
||
#define UART_GET_RXFIFO_OVF_INT_RAW(i) GET_PERI_REG_BITS2(UART_INT_RAW_REG(i) , UART_RXFIFO_OVF_INT_RAW_V, UART_RXFIFO_OVF_INT_RAW_S)
|
||
#define UART_GET_FRM_ERR_INT_RAW(i) GET_PERI_REG_BITS2(UART_INT_RAW_REG(i) , UART_FRM_ERR_INT_RAW_V, UART_FRM_ERR_INT_RAW_S)
|
||
#define UART_GET_PARITY_ERR_INT_RAW(i) GET_PERI_REG_BITS2(UART_INT_RAW_REG(i) , UART_PARITY_ERR_INT_RAW_V, UART_PARITY_ERR_INT_RAW_S)
|
||
#define UART_GET_TXFIFO_EMPTY_INT_RAW(i) GET_PERI_REG_BITS2(UART_INT_RAW_REG(i) , UART_TXFIFO_EMPTY_INT_RAW_V, UART_TXFIFO_EMPTY_INT_RAW_S)
|
||
#define UART_GET_RXFIFO_FULL_INT_RAW(i) GET_PERI_REG_BITS2(UART_INT_RAW_REG(i) , UART_RXFIFO_FULL_INT_RAW_V, UART_RXFIFO_FULL_INT_RAW_S)
|
||
|
||
|
||
|
||
#define UART_INT_ST_REG(i) (REG_UART_BASE(i) + 0x8)
|
||
/* UART_AT_CMD_CHAR_DET_INT_ST : RO ;bitpos:[18] ;default: 1'b0 ; */
|
||
/*description: The interrupt state bit for detecting AT_CMD char interrupt*/
|
||
#define UART_AT_CMD_CHAR_DET_INT_ST (BIT(18))
|
||
#define UART_AT_CMD_CHAR_DET_INT_ST_M (BIT(18))
|
||
#define UART_AT_CMD_CHAR_DET_INT_ST_V 0x1
|
||
#define UART_AT_CMD_CHAR_DET_INT_ST_S 18
|
||
/* UART_RS485_CLASH_INT_ST : RO ;bitpos:[17] ;default: 1'b0 ; */
|
||
/*description: The interrupt state bit for rs485 tx rx clash interrrupt*/
|
||
#define UART_RS485_CLASH_INT_ST (BIT(17))
|
||
#define UART_RS485_CLASH_INT_ST_M (BIT(17))
|
||
#define UART_RS485_CLASH_INT_ST_V 0x1
|
||
#define UART_RS485_CLASH_INT_ST_S 17
|
||
/* UART_RS485_FRM_ERR_INT_ST : RO ;bitpos:[16] ;default: 1'b0 ; */
|
||
/*description: The interrupt state bit for rs485 other rx error*/
|
||
#define UART_RS485_FRM_ERR_INT_ST (BIT(16))
|
||
#define UART_RS485_FRM_ERR_INT_ST_M (BIT(16))
|
||
#define UART_RS485_FRM_ERR_INT_ST_V 0x1
|
||
#define UART_RS485_FRM_ERR_INT_ST_S 16
|
||
/* UART_RS485_PARITY_ERR_INT_ST : RO ;bitpos:[15] ;default: 1'b0 ; */
|
||
/*description: The interrupt state bit for rs485 parity error*/
|
||
#define UART_RS485_PARITY_ERR_INT_ST (BIT(15))
|
||
#define UART_RS485_PARITY_ERR_INT_ST_M (BIT(15))
|
||
#define UART_RS485_PARITY_ERR_INT_ST_V 0x1
|
||
#define UART_RS485_PARITY_ERR_INT_ST_S 15
|
||
/* UART_TX_DONE_INT_ST : RO ;bitpos:[14] ;default: 1'b0 ; */
|
||
/*description: The interrupt state bit for tx done event*/
|
||
#define UART_TX_DONE_INT_ST (BIT(14))
|
||
#define UART_TX_DONE_INT_ST_M (BIT(14))
|
||
#define UART_TX_DONE_INT_ST_V 0x1
|
||
#define UART_TX_DONE_INT_ST_S 14
|
||
/* UART_TX_BRK_IDLE_DONE_INT_ST : RO ;bitpos:[13] ;default: 1'b0 ; */
|
||
/*description: The interrupt state bit for tx send idle done event*/
|
||
#define UART_TX_BRK_IDLE_DONE_INT_ST (BIT(13))
|
||
#define UART_TX_BRK_IDLE_DONE_INT_ST_M (BIT(13))
|
||
#define UART_TX_BRK_IDLE_DONE_INT_ST_V 0x1
|
||
#define UART_TX_BRK_IDLE_DONE_INT_ST_S 13
|
||
/* UART_TX_BRK_DONE_INT_ST : RO ;bitpos:[12] ;default: 1'b0 ; */
|
||
/*description: The interrupt state bit for send 0 done event*/
|
||
#define UART_TX_BRK_DONE_INT_ST (BIT(12))
|
||
#define UART_TX_BRK_DONE_INT_ST_M (BIT(12))
|
||
#define UART_TX_BRK_DONE_INT_ST_V 0x1
|
||
#define UART_TX_BRK_DONE_INT_ST_S 12
|
||
/* UART_GLITCH_DET_INT_ST : RO ;bitpos:[11] ;default: 1'b0 ; */
|
||
/*description: The interrupt state bit for detecting rx glitch pulse event*/
|
||
#define UART_GLITCH_DET_INT_ST (BIT(11))
|
||
#define UART_GLITCH_DET_INT_ST_M (BIT(11))
|
||
#define UART_GLITCH_DET_INT_ST_V 0x1
|
||
#define UART_GLITCH_DET_INT_ST_S 11
|
||
/* UART_SW_XOFF_INT_ST : RO ;bitpos:[10] ;default: 1'b0 ; */
|
||
/*description: The interrupt state bit for rx receive xoff char event*/
|
||
#define UART_SW_XOFF_INT_ST (BIT(10))
|
||
#define UART_SW_XOFF_INT_ST_M (BIT(10))
|
||
#define UART_SW_XOFF_INT_ST_V 0x1
|
||
#define UART_SW_XOFF_INT_ST_S 10
|
||
/* UART_SW_XON_INT_ST : RO ;bitpos:[9] ;default: 1'b0 ; */
|
||
/*description: The interrupt state bit for rx receive xon char event*/
|
||
#define UART_SW_XON_INT_ST (BIT(9))
|
||
#define UART_SW_XON_INT_ST_M (BIT(9))
|
||
#define UART_SW_XON_INT_ST_V 0x1
|
||
#define UART_SW_XON_INT_ST_S 9
|
||
/* UART_RXFIFO_TOUT_INT_ST : RO ;bitpos:[8] ;default: 1'b0 ; */
|
||
/*description: The interrupt state bit for Rx time-out event*/
|
||
#define UART_RXFIFO_TOUT_INT_ST (BIT(8))
|
||
#define UART_RXFIFO_TOUT_INT_ST_M (BIT(8))
|
||
#define UART_RXFIFO_TOUT_INT_ST_V 0x1
|
||
#define UART_RXFIFO_TOUT_INT_ST_S 8
|
||
/* UART_BRK_DET_INT_ST : RO ;bitpos:[7] ;default: 1'b0 ; */
|
||
/*description: The interrupt state bit for rx byte start error*/
|
||
#define UART_BRK_DET_INT_ST (BIT(7))
|
||
#define UART_BRK_DET_INT_ST_M (BIT(7))
|
||
#define UART_BRK_DET_INT_ST_V 0x1
|
||
#define UART_BRK_DET_INT_ST_S 7
|
||
/* UART_CTS_CHG_INT_ST : RO ;bitpos:[6] ;default: 1'b0 ; */
|
||
/*description: The interrupt state bit for CTS changing level*/
|
||
#define UART_CTS_CHG_INT_ST (BIT(6))
|
||
#define UART_CTS_CHG_INT_ST_M (BIT(6))
|
||
#define UART_CTS_CHG_INT_ST_V 0x1
|
||
#define UART_CTS_CHG_INT_ST_S 6
|
||
/* UART_DSR_CHG_INT_ST : RO ;bitpos:[5] ;default: 1'b0 ; */
|
||
/*description: The interrupt state bit for DSR changing level*/
|
||
#define UART_DSR_CHG_INT_ST (BIT(5))
|
||
#define UART_DSR_CHG_INT_ST_M (BIT(5))
|
||
#define UART_DSR_CHG_INT_ST_V 0x1
|
||
#define UART_DSR_CHG_INT_ST_S 5
|
||
/* UART_RXFIFO_OVF_INT_ST : RO ;bitpos:[4] ;default: 1'b0 ; */
|
||
/*description: The interrupt state bit for RX fifo overflow*/
|
||
#define UART_RXFIFO_OVF_INT_ST (BIT(4))
|
||
#define UART_RXFIFO_OVF_INT_ST_M (BIT(4))
|
||
#define UART_RXFIFO_OVF_INT_ST_V 0x1
|
||
#define UART_RXFIFO_OVF_INT_ST_S 4
|
||
/* UART_FRM_ERR_INT_ST : RO ;bitpos:[3] ;default: 1'b0 ; */
|
||
/*description: The interrupt state for other rx error*/
|
||
#define UART_FRM_ERR_INT_ST (BIT(3))
|
||
#define UART_FRM_ERR_INT_ST_M (BIT(3))
|
||
#define UART_FRM_ERR_INT_ST_V 0x1
|
||
#define UART_FRM_ERR_INT_ST_S 3
|
||
/* UART_PARITY_ERR_INT_ST : RO ;bitpos:[2] ;default: 1'b0 ; */
|
||
/*description: The interrupt state bit for rx parity error*/
|
||
#define UART_PARITY_ERR_INT_ST (BIT(2))
|
||
#define UART_PARITY_ERR_INT_ST_M (BIT(2))
|
||
#define UART_PARITY_ERR_INT_ST_V 0x1
|
||
#define UART_PARITY_ERR_INT_ST_S 2
|
||
/* UART_TXFIFO_EMPTY_INT_ST : RO ;bitpos:[1] ;default: 1'b0 ; */
|
||
/*description: The interrupt state bit for TX fifo empty*/
|
||
#define UART_TXFIFO_EMPTY_INT_ST (BIT(1))
|
||
#define UART_TXFIFO_EMPTY_INT_ST_M (BIT(1))
|
||
#define UART_TXFIFO_EMPTY_INT_ST_V 0x1
|
||
#define UART_TXFIFO_EMPTY_INT_ST_S 1
|
||
/* UART_RXFIFO_FULL_INT_ST : RO ;bitpos:[0] ;default: 1'b0 ; */
|
||
/*description: The interrupt state bit for RX fifo full event*/
|
||
#define UART_RXFIFO_FULL_INT_ST (BIT(0))
|
||
#define UART_RXFIFO_FULL_INT_ST_M (BIT(0))
|
||
#define UART_RXFIFO_FULL_INT_ST_V 0x1
|
||
#define UART_RXFIFO_FULL_INT_ST_S 0
|
||
#define UART_GET_AT_CMD_CHAR_DET_INT_ST(i) GET_PERI_REG_BITS2(UART_INT_ST_REG(i) , UART_AT_CMD_CHAR_DET_INT_ST_V, UART_AT_CMD_CHAR_DET_INT_ST_S)
|
||
#define UART_GET_RS485_CLASH_INT_ST(i) GET_PERI_REG_BITS2(UART_INT_ST_REG(i) , UART_RS485_CLASH_INT_ST_V, UART_RS485_CLASH_INT_ST_S)
|
||
#define UART_GET_RS485_FRM_ERR_INT_ST(i) GET_PERI_REG_BITS2(UART_INT_ST_REG(i) , UART_RS485_FRM_ERR_INT_ST_V, UART_RS485_FRM_ERR_INT_ST_S)
|
||
#define UART_GET_RS485_PARITY_ERR_INT_ST(i) GET_PERI_REG_BITS2(UART_INT_ST_REG(i) , UART_RS485_PARITY_ERR_INT_ST_V, UART_RS485_PARITY_ERR_INT_ST_S)
|
||
#define UART_GET_TX_DONE_INT_ST(i) GET_PERI_REG_BITS2(UART_INT_ST_REG(i) , UART_TX_DONE_INT_ST_V, UART_TX_DONE_INT_ST_S)
|
||
#define UART_GET_TX_BRK_IDLE_DONE_INT_ST(i) GET_PERI_REG_BITS2(UART_INT_ST_REG(i) , UART_TX_BRK_IDLE_DONE_INT_ST_V, UART_TX_BRK_IDLE_DONE_INT_ST_S)
|
||
#define UART_GET_TX_BRK_DONE_INT_ST(i) GET_PERI_REG_BITS2(UART_INT_ST_REG(i) , UART_TX_BRK_DONE_INT_ST_V, UART_TX_BRK_DONE_INT_ST_S)
|
||
#define UART_GET_GLITCH_DET_INT_ST(i) GET_PERI_REG_BITS2(UART_INT_ST_REG(i) , UART_GLITCH_DET_INT_ST_V, UART_GLITCH_DET_INT_ST_S)
|
||
#define UART_GET_SW_XOFF_INT_ST(i) GET_PERI_REG_BITS2(UART_INT_ST_REG(i) , UART_SW_XOFF_INT_ST_V, UART_SW_XOFF_INT_ST_S)
|
||
#define UART_GET_SW_XON_INT_ST(i) GET_PERI_REG_BITS2(UART_INT_ST_REG(i) , UART_SW_XON_INT_ST_V, UART_SW_XON_INT_ST_S)
|
||
#define UART_GET_RXFIFO_TOUT_INT_ST(i) GET_PERI_REG_BITS2(UART_INT_ST_REG(i) , UART_RXFIFO_TOUT_INT_ST_V, UART_RXFIFO_TOUT_INT_ST_S)
|
||
#define UART_GET_BRK_DET_INT_ST(i) GET_PERI_REG_BITS2(UART_INT_ST_REG(i) , UART_BRK_DET_INT_ST_V, UART_BRK_DET_INT_ST_S)
|
||
#define UART_GET_CTS_CHG_INT_ST(i) GET_PERI_REG_BITS2(UART_INT_ST_REG(i) , UART_CTS_CHG_INT_ST_V, UART_CTS_CHG_INT_ST_S)
|
||
#define UART_GET_DSR_CHG_INT_ST(i) GET_PERI_REG_BITS2(UART_INT_ST_REG(i) , UART_DSR_CHG_INT_ST_V, UART_DSR_CHG_INT_ST_S)
|
||
#define UART_GET_RXFIFO_OVF_INT_ST(i) GET_PERI_REG_BITS2(UART_INT_ST_REG(i) , UART_RXFIFO_OVF_INT_ST_V, UART_RXFIFO_OVF_INT_ST_S)
|
||
#define UART_GET_FRM_ERR_INT_ST(i) GET_PERI_REG_BITS2(UART_INT_ST_REG(i) , UART_FRM_ERR_INT_ST_V, UART_FRM_ERR_INT_ST_S)
|
||
#define UART_GET_PARITY_ERR_INT_ST(i) GET_PERI_REG_BITS2(UART_INT_ST_REG(i) , UART_PARITY_ERR_INT_ST_V, UART_PARITY_ERR_INT_ST_S)
|
||
#define UART_GET_TXFIFO_EMPTY_INT_ST(i) GET_PERI_REG_BITS2(UART_INT_ST_REG(i) , UART_TXFIFO_EMPTY_INT_ST_V, UART_TXFIFO_EMPTY_INT_ST_S)
|
||
#define UART_GET_RXFIFO_FULL_INT_ST(i) GET_PERI_REG_BITS2(UART_INT_ST_REG(i) , UART_RXFIFO_FULL_INT_ST_V, UART_RXFIFO_FULL_INT_ST_S)
|
||
|
||
|
||
|
||
#define UART_INT_ENA_REG(i) (REG_UART_BASE(i) + 0xC)
|
||
/* UART_AT_CMD_CHAR_DET_INT_ENA : R/W ;bitpos:[18] ;default: 1'b0 ; */
|
||
/*description: The interrupt enable bit for detecting AT_CMD char interrupt*/
|
||
#define UART_AT_CMD_CHAR_DET_INT_ENA (BIT(18))
|
||
#define UART_AT_CMD_CHAR_DET_INT_ENA_M (BIT(18))
|
||
#define UART_AT_CMD_CHAR_DET_INT_ENA_V 0x1
|
||
#define UART_AT_CMD_CHAR_DET_INT_ENA_S 18
|
||
/* UART_RS485_CLASH_INT_ENA : R/W ;bitpos:[17] ;default: 1'b0 ; */
|
||
/*description: The interrupt enable bit for rs485 tx rx clash interrrupt*/
|
||
#define UART_RS485_CLASH_INT_ENA (BIT(17))
|
||
#define UART_RS485_CLASH_INT_ENA_M (BIT(17))
|
||
#define UART_RS485_CLASH_INT_ENA_V 0x1
|
||
#define UART_RS485_CLASH_INT_ENA_S 17
|
||
/* UART_RS485_FRM_ERR_INT_ENA : R/W ;bitpos:[16] ;default: 1'b0 ; */
|
||
/*description: The interrupt enable bit for rs485 other rx error*/
|
||
#define UART_RS485_FRM_ERR_INT_ENA (BIT(16))
|
||
#define UART_RS485_FRM_ERR_INT_ENA_M (BIT(16))
|
||
#define UART_RS485_FRM_ERR_INT_ENA_V 0x1
|
||
#define UART_RS485_FRM_ERR_INT_ENA_S 16
|
||
/* UART_RS485_PARITY_ERR_INT_ENA : R/W ;bitpos:[15] ;default: 1'b0 ; */
|
||
/*description: The interrupt enable bit for rs485 parity error*/
|
||
#define UART_RS485_PARITY_ERR_INT_ENA (BIT(15))
|
||
#define UART_RS485_PARITY_ERR_INT_ENA_M (BIT(15))
|
||
#define UART_RS485_PARITY_ERR_INT_ENA_V 0x1
|
||
#define UART_RS485_PARITY_ERR_INT_ENA_S 15
|
||
/* UART_TX_DONE_INT_ENA : R/W ;bitpos:[14] ;default: 1'b0 ; */
|
||
/*description: The interrupt enable bit for tx done interrupt*/
|
||
#define UART_TX_DONE_INT_ENA (BIT(14))
|
||
#define UART_TX_DONE_INT_ENA_M (BIT(14))
|
||
#define UART_TX_DONE_INT_ENA_V 0x1
|
||
#define UART_TX_DONE_INT_ENA_S 14
|
||
/* UART_TX_BRK_IDLE_DONE_INT_ENA : R/W ;bitpos:[13] ;default: 1'b0 ; */
|
||
/*description: The interrupt enable bit for tx send idle done interrupt*/
|
||
#define UART_TX_BRK_IDLE_DONE_INT_ENA (BIT(13))
|
||
#define UART_TX_BRK_IDLE_DONE_INT_ENA_M (BIT(13))
|
||
#define UART_TX_BRK_IDLE_DONE_INT_ENA_V 0x1
|
||
#define UART_TX_BRK_IDLE_DONE_INT_ENA_S 13
|
||
/* UART_TX_BRK_DONE_INT_ENA : R/W ;bitpos:[12] ;default: 1'b0 ; */
|
||
/*description: The interrupt enable bit for send 0 done interrupt*/
|
||
#define UART_TX_BRK_DONE_INT_ENA (BIT(12))
|
||
#define UART_TX_BRK_DONE_INT_ENA_M (BIT(12))
|
||
#define UART_TX_BRK_DONE_INT_ENA_V 0x1
|
||
#define UART_TX_BRK_DONE_INT_ENA_S 12
|
||
/* UART_GLITCH_DET_INT_ENA : R/W ;bitpos:[11] ;default: 1'b0 ; */
|
||
/*description: The interrupt enable bit for detecting rx glitch pulse interrupt*/
|
||
#define UART_GLITCH_DET_INT_ENA (BIT(11))
|
||
#define UART_GLITCH_DET_INT_ENA_M (BIT(11))
|
||
#define UART_GLITCH_DET_INT_ENA_V 0x1
|
||
#define UART_GLITCH_DET_INT_ENA_S 11
|
||
/* UART_SW_XOFF_INT_ENA : R/W ;bitpos:[10] ;default: 1'b0 ; */
|
||
/*description: The interrupt enable bit for rx receive xoff char interrupt*/
|
||
#define UART_SW_XOFF_INT_ENA (BIT(10))
|
||
#define UART_SW_XOFF_INT_ENA_M (BIT(10))
|
||
#define UART_SW_XOFF_INT_ENA_V 0x1
|
||
#define UART_SW_XOFF_INT_ENA_S 10
|
||
/* UART_SW_XON_INT_ENA : R/W ;bitpos:[9] ;default: 1'b0 ; */
|
||
/*description: The interrupt enable bit for rx receive xon char interrupt*/
|
||
#define UART_SW_XON_INT_ENA (BIT(9))
|
||
#define UART_SW_XON_INT_ENA_M (BIT(9))
|
||
#define UART_SW_XON_INT_ENA_V 0x1
|
||
#define UART_SW_XON_INT_ENA_S 9
|
||
/* UART_RXFIFO_TOUT_INT_ENA : R/W ;bitpos:[8] ;default: 1'b0 ; */
|
||
/*description: The interrupt enable bit for rx time-out interrupt*/
|
||
#define UART_RXFIFO_TOUT_INT_ENA (BIT(8))
|
||
#define UART_RXFIFO_TOUT_INT_ENA_M (BIT(8))
|
||
#define UART_RXFIFO_TOUT_INT_ENA_V 0x1
|
||
#define UART_RXFIFO_TOUT_INT_ENA_S 8
|
||
/* UART_BRK_DET_INT_ENA : R/W ;bitpos:[7] ;default: 1'b0 ; */
|
||
/*description: The interrupt enable bit for rx byte start error*/
|
||
#define UART_BRK_DET_INT_ENA (BIT(7))
|
||
#define UART_BRK_DET_INT_ENA_M (BIT(7))
|
||
#define UART_BRK_DET_INT_ENA_V 0x1
|
||
#define UART_BRK_DET_INT_ENA_S 7
|
||
/* UART_CTS_CHG_INT_ENA : R/W ;bitpos:[6] ;default: 1'b0 ; */
|
||
/*description: The interrupt enable bit for CTS changing level*/
|
||
#define UART_CTS_CHG_INT_ENA (BIT(6))
|
||
#define UART_CTS_CHG_INT_ENA_M (BIT(6))
|
||
#define UART_CTS_CHG_INT_ENA_V 0x1
|
||
#define UART_CTS_CHG_INT_ENA_S 6
|
||
/* UART_DSR_CHG_INT_ENA : R/W ;bitpos:[5] ;default: 1'b0 ; */
|
||
/*description: The interrupt enable bit for DSR changing level*/
|
||
#define UART_DSR_CHG_INT_ENA (BIT(5))
|
||
#define UART_DSR_CHG_INT_ENA_M (BIT(5))
|
||
#define UART_DSR_CHG_INT_ENA_V 0x1
|
||
#define UART_DSR_CHG_INT_ENA_S 5
|
||
/* UART_RXFIFO_OVF_INT_ENA : R/W ;bitpos:[4] ;default: 1'b0 ; */
|
||
/*description: The interrupt enable bit for rx fifo overflow*/
|
||
#define UART_RXFIFO_OVF_INT_ENA (BIT(4))
|
||
#define UART_RXFIFO_OVF_INT_ENA_M (BIT(4))
|
||
#define UART_RXFIFO_OVF_INT_ENA_V 0x1
|
||
#define UART_RXFIFO_OVF_INT_ENA_S 4
|
||
/* UART_FRM_ERR_INT_ENA : R/W ;bitpos:[3] ;default: 1'b0 ; */
|
||
/*description: The interrupt enable bit for other rx error*/
|
||
#define UART_FRM_ERR_INT_ENA (BIT(3))
|
||
#define UART_FRM_ERR_INT_ENA_M (BIT(3))
|
||
#define UART_FRM_ERR_INT_ENA_V 0x1
|
||
#define UART_FRM_ERR_INT_ENA_S 3
|
||
/* UART_PARITY_ERR_INT_ENA : R/W ;bitpos:[2] ;default: 1'b0 ; */
|
||
/*description: The interrupt enable bit for parity error*/
|
||
#define UART_PARITY_ERR_INT_ENA (BIT(2))
|
||
#define UART_PARITY_ERR_INT_ENA_M (BIT(2))
|
||
#define UART_PARITY_ERR_INT_ENA_V 0x1
|
||
#define UART_PARITY_ERR_INT_ENA_S 2
|
||
/* UART_TXFIFO_EMPTY_INT_ENA : R/W ;bitpos:[1] ;default: 1'b0 ; */
|
||
/*description: The interrupt enable bit for tx fifo empty event*/
|
||
#define UART_TXFIFO_EMPTY_INT_ENA (BIT(1))
|
||
#define UART_TXFIFO_EMPTY_INT_ENA_M (BIT(1))
|
||
#define UART_TXFIFO_EMPTY_INT_ENA_V 0x1
|
||
#define UART_TXFIFO_EMPTY_INT_ENA_S 1
|
||
/* UART_RXFIFO_FULL_INT_ENA : R/W ;bitpos:[0] ;default: 1'b0 ; */
|
||
/*description: The interrupt enable bit for rx fifo full event*/
|
||
#define UART_RXFIFO_FULL_INT_ENA (BIT(0))
|
||
#define UART_RXFIFO_FULL_INT_ENA_M (BIT(0))
|
||
#define UART_RXFIFO_FULL_INT_ENA_V 0x1
|
||
#define UART_RXFIFO_FULL_INT_ENA_S 0
|
||
#define UART_GET_AT_CMD_CHAR_DET_INT_ENA(i) GET_PERI_REG_BITS2(UART_INT_ENA_REG(i) , UART_AT_CMD_CHAR_DET_INT_ENA_V, UART_AT_CMD_CHAR_DET_INT_ENA_S)
|
||
#define UART_SET_AT_CMD_CHAR_DET_INT_ENA(i,val) SET_PERI_REG_BITS(UART_INT_ENA_REG(i) ,UART_AT_CMD_CHAR_DET_INT_ENA_V,(val),UART_AT_CMD_CHAR_DET_INT_ENA_S)
|
||
#define UART_GET_RS485_CLASH_INT_ENA(i) GET_PERI_REG_BITS2(UART_INT_ENA_REG(i) , UART_RS485_CLASH_INT_ENA_V, UART_RS485_CLASH_INT_ENA_S)
|
||
#define UART_SET_RS485_CLASH_INT_ENA(i,val) SET_PERI_REG_BITS(UART_INT_ENA_REG(i) ,UART_RS485_CLASH_INT_ENA_V,(val),UART_RS485_CLASH_INT_ENA_S)
|
||
#define UART_GET_RS485_FRM_ERR_INT_ENA(i) GET_PERI_REG_BITS2(UART_INT_ENA_REG(i) , UART_RS485_FRM_ERR_INT_ENA_V, UART_RS485_FRM_ERR_INT_ENA_S)
|
||
#define UART_SET_RS485_FRM_ERR_INT_ENA(i,val) SET_PERI_REG_BITS(UART_INT_ENA_REG(i) ,UART_RS485_FRM_ERR_INT_ENA_V,(val),UART_RS485_FRM_ERR_INT_ENA_S)
|
||
#define UART_GET_RS485_PARITY_ERR_INT_ENA(i) GET_PERI_REG_BITS2(UART_INT_ENA_REG(i) , UART_RS485_PARITY_ERR_INT_ENA_V, UART_RS485_PARITY_ERR_INT_ENA_S)
|
||
#define UART_SET_RS485_PARITY_ERR_INT_ENA(i,val) SET_PERI_REG_BITS(UART_INT_ENA_REG(i) ,UART_RS485_PARITY_ERR_INT_ENA_V,(val),UART_RS485_PARITY_ERR_INT_ENA_S)
|
||
#define UART_GET_TX_DONE_INT_ENA(i) GET_PERI_REG_BITS2(UART_INT_ENA_REG(i) , UART_TX_DONE_INT_ENA_V, UART_TX_DONE_INT_ENA_S)
|
||
#define UART_SET_TX_DONE_INT_ENA(i,val) SET_PERI_REG_BITS(UART_INT_ENA_REG(i) ,UART_TX_DONE_INT_ENA_V,(val),UART_TX_DONE_INT_ENA_S)
|
||
#define UART_GET_TX_BRK_IDLE_DONE_INT_ENA(i) GET_PERI_REG_BITS2(UART_INT_ENA_REG(i) , UART_TX_BRK_IDLE_DONE_INT_ENA_V, UART_TX_BRK_IDLE_DONE_INT_ENA_S)
|
||
#define UART_SET_TX_BRK_IDLE_DONE_INT_ENA(i,val) SET_PERI_REG_BITS(UART_INT_ENA_REG(i) ,UART_TX_BRK_IDLE_DONE_INT_ENA_V,(val),UART_TX_BRK_IDLE_DONE_INT_ENA_S)
|
||
#define UART_GET_TX_BRK_DONE_INT_ENA(i) GET_PERI_REG_BITS2(UART_INT_ENA_REG(i) , UART_TX_BRK_DONE_INT_ENA_V, UART_TX_BRK_DONE_INT_ENA_S)
|
||
#define UART_SET_TX_BRK_DONE_INT_ENA(i,val) SET_PERI_REG_BITS(UART_INT_ENA_REG(i) ,UART_TX_BRK_DONE_INT_ENA_V,(val),UART_TX_BRK_DONE_INT_ENA_S)
|
||
#define UART_GET_GLITCH_DET_INT_ENA(i) GET_PERI_REG_BITS2(UART_INT_ENA_REG(i) , UART_GLITCH_DET_INT_ENA_V, UART_GLITCH_DET_INT_ENA_S)
|
||
#define UART_SET_GLITCH_DET_INT_ENA(i,val) SET_PERI_REG_BITS(UART_INT_ENA_REG(i) ,UART_GLITCH_DET_INT_ENA_V,(val),UART_GLITCH_DET_INT_ENA_S)
|
||
#define UART_GET_SW_XOFF_INT_ENA(i) GET_PERI_REG_BITS2(UART_INT_ENA_REG(i) , UART_SW_XOFF_INT_ENA_V, UART_SW_XOFF_INT_ENA_S)
|
||
#define UART_SET_SW_XOFF_INT_ENA(i,val) SET_PERI_REG_BITS(UART_INT_ENA_REG(i) ,UART_SW_XOFF_INT_ENA_V,(val),UART_SW_XOFF_INT_ENA_S)
|
||
#define UART_GET_SW_XON_INT_ENA(i) GET_PERI_REG_BITS2(UART_INT_ENA_REG(i) , UART_SW_XON_INT_ENA_V, UART_SW_XON_INT_ENA_S)
|
||
#define UART_SET_SW_XON_INT_ENA(i,val) SET_PERI_REG_BITS(UART_INT_ENA_REG(i) ,UART_SW_XON_INT_ENA_V,(val),UART_SW_XON_INT_ENA_S)
|
||
#define UART_GET_RXFIFO_TOUT_INT_ENA(i) GET_PERI_REG_BITS2(UART_INT_ENA_REG(i) , UART_RXFIFO_TOUT_INT_ENA_V, UART_RXFIFO_TOUT_INT_ENA_S)
|
||
#define UART_SET_RXFIFO_TOUT_INT_ENA(i,val) SET_PERI_REG_BITS(UART_INT_ENA_REG(i) ,UART_RXFIFO_TOUT_INT_ENA_V,(val),UART_RXFIFO_TOUT_INT_ENA_S)
|
||
#define UART_GET_BRK_DET_INT_ENA(i) GET_PERI_REG_BITS2(UART_INT_ENA_REG(i) , UART_BRK_DET_INT_ENA_V, UART_BRK_DET_INT_ENA_S)
|
||
#define UART_SET_BRK_DET_INT_ENA(i,val) SET_PERI_REG_BITS(UART_INT_ENA_REG(i) ,UART_BRK_DET_INT_ENA_V,(val),UART_BRK_DET_INT_ENA_S)
|
||
#define UART_GET_CTS_CHG_INT_ENA(i) GET_PERI_REG_BITS2(UART_INT_ENA_REG(i) , UART_CTS_CHG_INT_ENA_V, UART_CTS_CHG_INT_ENA_S)
|
||
#define UART_SET_CTS_CHG_INT_ENA(i,val) SET_PERI_REG_BITS(UART_INT_ENA_REG(i) ,UART_CTS_CHG_INT_ENA_V,(val),UART_CTS_CHG_INT_ENA_S)
|
||
#define UART_GET_DSR_CHG_INT_ENA(i) GET_PERI_REG_BITS2(UART_INT_ENA_REG(i) , UART_DSR_CHG_INT_ENA_V, UART_DSR_CHG_INT_ENA_S)
|
||
#define UART_SET_DSR_CHG_INT_ENA(i,val) SET_PERI_REG_BITS(UART_INT_ENA_REG(i) ,UART_DSR_CHG_INT_ENA_V,(val),UART_DSR_CHG_INT_ENA_S)
|
||
#define UART_GET_RXFIFO_OVF_INT_ENA(i) GET_PERI_REG_BITS2(UART_INT_ENA_REG(i) , UART_RXFIFO_OVF_INT_ENA_V, UART_RXFIFO_OVF_INT_ENA_S)
|
||
#define UART_SET_RXFIFO_OVF_INT_ENA(i,val) SET_PERI_REG_BITS(UART_INT_ENA_REG(i) ,UART_RXFIFO_OVF_INT_ENA_V,(val),UART_RXFIFO_OVF_INT_ENA_S)
|
||
#define UART_GET_FRM_ERR_INT_ENA(i) GET_PERI_REG_BITS2(UART_INT_ENA_REG(i) , UART_FRM_ERR_INT_ENA_V, UART_FRM_ERR_INT_ENA_S)
|
||
#define UART_SET_FRM_ERR_INT_ENA(i,val) SET_PERI_REG_BITS(UART_INT_ENA_REG(i) ,UART_FRM_ERR_INT_ENA_V,(val),UART_FRM_ERR_INT_ENA_S)
|
||
#define UART_GET_PARITY_ERR_INT_ENA(i) GET_PERI_REG_BITS2(UART_INT_ENA_REG(i) , UART_PARITY_ERR_INT_ENA_V, UART_PARITY_ERR_INT_ENA_S)
|
||
#define UART_SET_PARITY_ERR_INT_ENA(i,val) SET_PERI_REG_BITS(UART_INT_ENA_REG(i) ,UART_PARITY_ERR_INT_ENA_V,(val),UART_PARITY_ERR_INT_ENA_S)
|
||
#define UART_GET_TXFIFO_EMPTY_INT_ENA(i) GET_PERI_REG_BITS2(UART_INT_ENA_REG(i) , UART_TXFIFO_EMPTY_INT_ENA_V, UART_TXFIFO_EMPTY_INT_ENA_S)
|
||
#define UART_SET_TXFIFO_EMPTY_INT_ENA(i,val) SET_PERI_REG_BITS(UART_INT_ENA_REG(i) ,UART_TXFIFO_EMPTY_INT_ENA_V,(val),UART_TXFIFO_EMPTY_INT_ENA_S)
|
||
#define UART_GET_RXFIFO_FULL_INT_ENA(i) GET_PERI_REG_BITS2(UART_INT_ENA_REG(i) , UART_RXFIFO_FULL_INT_ENA_V, UART_RXFIFO_FULL_INT_ENA_S)
|
||
#define UART_SET_RXFIFO_FULL_INT_ENA(i,val) SET_PERI_REG_BITS(UART_INT_ENA_REG(i) ,UART_RXFIFO_FULL_INT_ENA_V,(val),UART_RXFIFO_FULL_INT_ENA_S)
|
||
|
||
|
||
|
||
#define UART_INT_CLR_REG(i) (REG_UART_BASE(i) + 0x10)
|
||
/* UART_AT_CMD_CHAR_DET_INT_CLR : WO ;bitpos:[18] ;default: 1'b0 ; */
|
||
/*description: Set this bit for detecting AT_CMD char interrupt*/
|
||
#define UART_AT_CMD_CHAR_DET_INT_CLR (BIT(18))
|
||
#define UART_AT_CMD_CHAR_DET_INT_CLR_M (BIT(18))
|
||
#define UART_AT_CMD_CHAR_DET_INT_CLR_V 0x1
|
||
#define UART_AT_CMD_CHAR_DET_INT_CLR_S 18
|
||
/* UART_RS485_CLASH_INT_CLR : WO ;bitpos:[17] ;default: 1'b0 ; */
|
||
/*description: Set this bit for rs485 tx rx clash interrrupt*/
|
||
#define UART_RS485_CLASH_INT_CLR (BIT(17))
|
||
#define UART_RS485_CLASH_INT_CLR_M (BIT(17))
|
||
#define UART_RS485_CLASH_INT_CLR_V 0x1
|
||
#define UART_RS485_CLASH_INT_CLR_S 17
|
||
/* UART_RS485_FRM_ERR_INT_CLR : WO ;bitpos:[16] ;default: 1'b0 ; */
|
||
/*description: Set this bit for rs485 other rx error*/
|
||
#define UART_RS485_FRM_ERR_INT_CLR (BIT(16))
|
||
#define UART_RS485_FRM_ERR_INT_CLR_M (BIT(16))
|
||
#define UART_RS485_FRM_ERR_INT_CLR_V 0x1
|
||
#define UART_RS485_FRM_ERR_INT_CLR_S 16
|
||
/* UART_RS485_PARITY_ERR_INT_CLR : WO ;bitpos:[15] ;default: 1'b0 ; */
|
||
/*description: Set this bit for rs485 parity error interrupt*/
|
||
#define UART_RS485_PARITY_ERR_INT_CLR (BIT(15))
|
||
#define UART_RS485_PARITY_ERR_INT_CLR_M (BIT(15))
|
||
#define UART_RS485_PARITY_ERR_INT_CLR_V 0x1
|
||
#define UART_RS485_PARITY_ERR_INT_CLR_S 15
|
||
/* UART_TX_DONE_INT_CLR : WO ;bitpos:[14] ;default: 1'b0 ; */
|
||
/*description: Set this bit to clear the tx done interrupt*/
|
||
#define UART_TX_DONE_INT_CLR (BIT(14))
|
||
#define UART_TX_DONE_INT_CLR_M (BIT(14))
|
||
#define UART_TX_DONE_INT_CLR_V 0x1
|
||
#define UART_TX_DONE_INT_CLR_S 14
|
||
/* UART_TX_BRK_IDLE_DONE_INT_CLR : WO ;bitpos:[13] ;default: 1'b0 ; */
|
||
/*description: Set this bit to clear the tx send idle done interrupt*/
|
||
#define UART_TX_BRK_IDLE_DONE_INT_CLR (BIT(13))
|
||
#define UART_TX_BRK_IDLE_DONE_INT_CLR_M (BIT(13))
|
||
#define UART_TX_BRK_IDLE_DONE_INT_CLR_V 0x1
|
||
#define UART_TX_BRK_IDLE_DONE_INT_CLR_S 13
|
||
/* UART_TX_BRK_DONE_INT_CLR : WO ;bitpos:[12] ;default: 1'b0 ; */
|
||
/*description: Set this bit to clear the send 0 done interrupt*/
|
||
#define UART_TX_BRK_DONE_INT_CLR (BIT(12))
|
||
#define UART_TX_BRK_DONE_INT_CLR_M (BIT(12))
|
||
#define UART_TX_BRK_DONE_INT_CLR_V 0x1
|
||
#define UART_TX_BRK_DONE_INT_CLR_S 12
|
||
/* UART_GLITCH_DET_INT_CLR : WO ;bitpos:[11] ;default: 1'b0 ; */
|
||
/*description: Set this bit to clear the detecting rx glitch pulse interrupt*/
|
||
#define UART_GLITCH_DET_INT_CLR (BIT(11))
|
||
#define UART_GLITCH_DET_INT_CLR_M (BIT(11))
|
||
#define UART_GLITCH_DET_INT_CLR_V 0x1
|
||
#define UART_GLITCH_DET_INT_CLR_S 11
|
||
/* UART_SW_XOFF_INT_CLR : WO ;bitpos:[10] ;default: 1'b0 ; */
|
||
/*description: Set this bit to clear the rx receive xoff char interrupt*/
|
||
#define UART_SW_XOFF_INT_CLR (BIT(10))
|
||
#define UART_SW_XOFF_INT_CLR_M (BIT(10))
|
||
#define UART_SW_XOFF_INT_CLR_V 0x1
|
||
#define UART_SW_XOFF_INT_CLR_S 10
|
||
/* UART_SW_XON_INT_CLR : WO ;bitpos:[9] ;default: 1'b0 ; */
|
||
/*description: Set this bit to clear the rx receive xon char interrupt*/
|
||
#define UART_SW_XON_INT_CLR (BIT(9))
|
||
#define UART_SW_XON_INT_CLR_M (BIT(9))
|
||
#define UART_SW_XON_INT_CLR_V 0x1
|
||
#define UART_SW_XON_INT_CLR_S 9
|
||
/* UART_RXFIFO_TOUT_INT_CLR : WO ;bitpos:[8] ;default: 1'b0 ; */
|
||
/*description: Set this bit to clear the rx time-out interrupt*/
|
||
#define UART_RXFIFO_TOUT_INT_CLR (BIT(8))
|
||
#define UART_RXFIFO_TOUT_INT_CLR_M (BIT(8))
|
||
#define UART_RXFIFO_TOUT_INT_CLR_V 0x1
|
||
#define UART_RXFIFO_TOUT_INT_CLR_S 8
|
||
/* UART_BRK_DET_INT_CLR : WO ;bitpos:[7] ;default: 1'b0 ; */
|
||
/*description: Set this bit to clear the rx byte start interrupt*/
|
||
#define UART_BRK_DET_INT_CLR (BIT(7))
|
||
#define UART_BRK_DET_INT_CLR_M (BIT(7))
|
||
#define UART_BRK_DET_INT_CLR_V 0x1
|
||
#define UART_BRK_DET_INT_CLR_S 7
|
||
/* UART_CTS_CHG_INT_CLR : WO ;bitpos:[6] ;default: 1'b0 ; */
|
||
/*description: Set this bit to clear the CTS changing interrupt*/
|
||
#define UART_CTS_CHG_INT_CLR (BIT(6))
|
||
#define UART_CTS_CHG_INT_CLR_M (BIT(6))
|
||
#define UART_CTS_CHG_INT_CLR_V 0x1
|
||
#define UART_CTS_CHG_INT_CLR_S 6
|
||
/* UART_DSR_CHG_INT_CLR : WO ;bitpos:[5] ;default: 1'b0 ; */
|
||
/*description: Set this bit to clear the DSR changing interrupt*/
|
||
#define UART_DSR_CHG_INT_CLR (BIT(5))
|
||
#define UART_DSR_CHG_INT_CLR_M (BIT(5))
|
||
#define UART_DSR_CHG_INT_CLR_V 0x1
|
||
#define UART_DSR_CHG_INT_CLR_S 5
|
||
/* UART_RXFIFO_OVF_INT_CLR : WO ;bitpos:[4] ;default: 1'b0 ; */
|
||
/*description: Set this bit to clear the rx fifo over-flow interrupt*/
|
||
#define UART_RXFIFO_OVF_INT_CLR (BIT(4))
|
||
#define UART_RXFIFO_OVF_INT_CLR_M (BIT(4))
|
||
#define UART_RXFIFO_OVF_INT_CLR_V 0x1
|
||
#define UART_RXFIFO_OVF_INT_CLR_S 4
|
||
/* UART_FRM_ERR_INT_CLR : WO ;bitpos:[3] ;default: 1'b0 ; */
|
||
/*description: Set this bit to clear other rx error interrupt*/
|
||
#define UART_FRM_ERR_INT_CLR (BIT(3))
|
||
#define UART_FRM_ERR_INT_CLR_M (BIT(3))
|
||
#define UART_FRM_ERR_INT_CLR_V 0x1
|
||
#define UART_FRM_ERR_INT_CLR_S 3
|
||
/* UART_PARITY_ERR_INT_CLR : WO ;bitpos:[2] ;default: 1'b0 ; */
|
||
/*description: Set this bit to clear the parity error interrupt*/
|
||
#define UART_PARITY_ERR_INT_CLR (BIT(2))
|
||
#define UART_PARITY_ERR_INT_CLR_M (BIT(2))
|
||
#define UART_PARITY_ERR_INT_CLR_V 0x1
|
||
#define UART_PARITY_ERR_INT_CLR_S 2
|
||
/* UART_TXFIFO_EMPTY_INT_CLR : WO ;bitpos:[1] ;default: 1'b0 ; */
|
||
/*description: Set this bit to clear the tx fifo empty interrupt*/
|
||
#define UART_TXFIFO_EMPTY_INT_CLR (BIT(1))
|
||
#define UART_TXFIFO_EMPTY_INT_CLR_M (BIT(1))
|
||
#define UART_TXFIFO_EMPTY_INT_CLR_V 0x1
|
||
#define UART_TXFIFO_EMPTY_INT_CLR_S 1
|
||
/* UART_RXFIFO_FULL_INT_CLR : WO ;bitpos:[0] ;default: 1'b0 ; */
|
||
/*description: Set this bit to clear the rx fifo full interrupt*/
|
||
#define UART_RXFIFO_FULL_INT_CLR (BIT(0))
|
||
#define UART_RXFIFO_FULL_INT_CLR_M (BIT(0))
|
||
#define UART_RXFIFO_FULL_INT_CLR_V 0x1
|
||
#define UART_RXFIFO_FULL_INT_CLR_S 0
|
||
#define UART_SET_AT_CMD_CHAR_DET_INT_CLR(i,val) SET_PERI_REG_BITS(UART_INT_CLR_REG(i) ,UART_AT_CMD_CHAR_DET_INT_CLR_V,(val),UART_AT_CMD_CHAR_DET_INT_CLR_S)
|
||
#define UART_SET_RS485_CLASH_INT_CLR(i,val) SET_PERI_REG_BITS(UART_INT_CLR_REG(i) ,UART_RS485_CLASH_INT_CLR_V,(val),UART_RS485_CLASH_INT_CLR_S)
|
||
#define UART_SET_RS485_FRM_ERR_INT_CLR(i,val) SET_PERI_REG_BITS(UART_INT_CLR_REG(i) ,UART_RS485_FRM_ERR_INT_CLR_V,(val),UART_RS485_FRM_ERR_INT_CLR_S)
|
||
#define UART_SET_RS485_PARITY_ERR_INT_CLR(i,val) SET_PERI_REG_BITS(UART_INT_CLR_REG(i) ,UART_RS485_PARITY_ERR_INT_CLR_V,(val),UART_RS485_PARITY_ERR_INT_CLR_S)
|
||
#define UART_SET_TX_DONE_INT_CLR(i,val) SET_PERI_REG_BITS(UART_INT_CLR_REG(i) ,UART_TX_DONE_INT_CLR_V,(val),UART_TX_DONE_INT_CLR_S)
|
||
#define UART_SET_TX_BRK_IDLE_DONE_INT_CLR(i,val) SET_PERI_REG_BITS(UART_INT_CLR_REG(i) ,UART_TX_BRK_IDLE_DONE_INT_CLR_V,(val),UART_TX_BRK_IDLE_DONE_INT_CLR_S)
|
||
#define UART_SET_TX_BRK_DONE_INT_CLR(i,val) SET_PERI_REG_BITS(UART_INT_CLR_REG(i) ,UART_TX_BRK_DONE_INT_CLR_V,(val),UART_TX_BRK_DONE_INT_CLR_S)
|
||
#define UART_SET_GLITCH_DET_INT_CLR(i,val) SET_PERI_REG_BITS(UART_INT_CLR_REG(i) ,UART_GLITCH_DET_INT_CLR_V,(val),UART_GLITCH_DET_INT_CLR_S)
|
||
#define UART_SET_SW_XOFF_INT_CLR(i,val) SET_PERI_REG_BITS(UART_INT_CLR_REG(i) ,UART_SW_XOFF_INT_CLR_V,(val),UART_SW_XOFF_INT_CLR_S)
|
||
#define UART_SET_SW_XON_INT_CLR(i,val) SET_PERI_REG_BITS(UART_INT_CLR_REG(i) ,UART_SW_XON_INT_CLR_V,(val),UART_SW_XON_INT_CLR_S)
|
||
#define UART_SET_RXFIFO_TOUT_INT_CLR(i,val) SET_PERI_REG_BITS(UART_INT_CLR_REG(i) ,UART_RXFIFO_TOUT_INT_CLR_V,(val),UART_RXFIFO_TOUT_INT_CLR_S)
|
||
#define UART_SET_BRK_DET_INT_CLR(i,val) SET_PERI_REG_BITS(UART_INT_CLR_REG(i) ,UART_BRK_DET_INT_CLR_V,(val),UART_BRK_DET_INT_CLR_S)
|
||
#define UART_SET_CTS_CHG_INT_CLR(i,val) SET_PERI_REG_BITS(UART_INT_CLR_REG(i) ,UART_CTS_CHG_INT_CLR_V,(val),UART_CTS_CHG_INT_CLR_S)
|
||
#define UART_SET_DSR_CHG_INT_CLR(i,val) SET_PERI_REG_BITS(UART_INT_CLR_REG(i) ,UART_DSR_CHG_INT_CLR_V,(val),UART_DSR_CHG_INT_CLR_S)
|
||
#define UART_SET_RXFIFO_OVF_INT_CLR(i,val) SET_PERI_REG_BITS(UART_INT_CLR_REG(i) ,UART_RXFIFO_OVF_INT_CLR_V,(val),UART_RXFIFO_OVF_INT_CLR_S)
|
||
#define UART_SET_FRM_ERR_INT_CLR(i,val) SET_PERI_REG_BITS(UART_INT_CLR_REG(i) ,UART_FRM_ERR_INT_CLR_V,(val),UART_FRM_ERR_INT_CLR_S)
|
||
#define UART_SET_PARITY_ERR_INT_CLR(i,val) SET_PERI_REG_BITS(UART_INT_CLR_REG(i) ,UART_PARITY_ERR_INT_CLR_V,(val),UART_PARITY_ERR_INT_CLR_S)
|
||
#define UART_SET_TXFIFO_EMPTY_INT_CLR(i,val) SET_PERI_REG_BITS(UART_INT_CLR_REG(i) ,UART_TXFIFO_EMPTY_INT_CLR_V,(val),UART_TXFIFO_EMPTY_INT_CLR_S)
|
||
#define UART_SET_RXFIFO_FULL_INT_CLR(i,val) SET_PERI_REG_BITS(UART_INT_CLR_REG(i) ,UART_RXFIFO_FULL_INT_CLR_V,(val),UART_RXFIFO_FULL_INT_CLR_S)
|
||
|
||
|
||
|
||
#define UART_CLKDIV_REG(i) (REG_UART_BASE(i) + 0x14)
|
||
/* UART_CLKDIV_FRAG : R/W ;bitpos:[23:20] ;default: 4'b0 ; */
|
||
/*description: The decimal part of divider*/
|
||
#define UART_CLKDIV_FRAG 0x0000000F
|
||
#define UART_CLKDIV_FRAG_M ((UART_CLKDIV_FRAG_V)<<(UART_CLKDIV_FRAG_S))
|
||
#define UART_CLKDIV_FRAG_V 0xF
|
||
#define UART_CLKDIV_FRAG_S 20
|
||
/* UART_CLKDIV : R/W ;bitpos:[19:0] ;default: 20'h2B6 ; */
|
||
/*description: The interger part of divider BAUDRATE = UART_CLK_FREQ / UART_CLKDIV*/
|
||
#define UART_CLKDIV 0x000FFFFF
|
||
#define UART_CLKDIV_M ((UART_CLKDIV_V)<<(UART_CLKDIV_S))
|
||
#define UART_CLKDIV_V 0xFFFFF
|
||
#define UART_CLKDIV_S 0
|
||
#define UART_GET_CLKDIV_FRAG(i) GET_PERI_REG_BITS2(UART_CLKDIV_REG(i) , UART_CLKDIV_FRAG_V, UART_CLKDIV_FRAG_S)
|
||
#define UART_SET_CLKDIV_FRAG(i,val) SET_PERI_REG_BITS(UART_CLKDIV_REG(i) ,UART_CLKDIV_FRAG_V,(val),UART_CLKDIV_FRAG_S)
|
||
#define UART_GET_CLKDIV(i) GET_PERI_REG_BITS2(UART_CLKDIV_REG(i) , UART_CLKDIV_V, UART_CLKDIV_S)
|
||
#define UART_SET_CLKDIV(i,val) SET_PERI_REG_BITS(UART_CLKDIV_REG(i) ,UART_CLKDIV_V,(val),UART_CLKDIV_S)
|
||
|
||
|
||
|
||
#define UART_AUTOBAUD_REG(i) (REG_UART_BASE(i) + 0x18)
|
||
/* UART_GLITCH_FILT : R/W ;bitpos:[15:8] ;default: 8'h10 ; */
|
||
/*description: ignore the glitch when pulse cnt is lower then this value*/
|
||
#define UART_GLITCH_FILT 0x000000FF
|
||
#define UART_GLITCH_FILT_M ((UART_GLITCH_FILT_V)<<(UART_GLITCH_FILT_S))
|
||
#define UART_GLITCH_FILT_V 0xFF
|
||
#define UART_GLITCH_FILT_S 8
|
||
/* UART_AUTOBAUD_EN : R/W ;bitpos:[0] ;default: 1'b0 ; */
|
||
/*description: Set this bit to enable baudrate detect*/
|
||
#define UART_AUTOBAUD_EN (BIT(0))
|
||
#define UART_AUTOBAUD_EN_M (BIT(0))
|
||
#define UART_AUTOBAUD_EN_V 0x1
|
||
#define UART_AUTOBAUD_EN_S 0
|
||
#define UART_GET_GLITCH_FILT(i) GET_PERI_REG_BITS2(UART_AUTOBAUD_REG(i) , UART_GLITCH_FILT_V, UART_GLITCH_FILT_S)
|
||
#define UART_SET_GLITCH_FILT(i,val) SET_PERI_REG_BITS(UART_AUTOBAUD_REG(i) ,UART_GLITCH_FILT_V,(val),UART_GLITCH_FILT_S)
|
||
#define UART_GET_AUTOBAUD_EN(i) GET_PERI_REG_BITS2(UART_AUTOBAUD_REG(i) , UART_AUTOBAUD_EN_V, UART_AUTOBAUD_EN_S)
|
||
#define UART_SET_AUTOBAUD_EN(i,val) SET_PERI_REG_BITS(UART_AUTOBAUD_REG(i) ,UART_AUTOBAUD_EN_V,(val),UART_AUTOBAUD_EN_S)
|
||
|
||
|
||
|
||
#define UART_STATUS_REG(i) (REG_UART_BASE(i) + 0x1C)
|
||
/* UART_TXD : RO ;bitpos:[31] ;default: 8'h0 ; */
|
||
/*description: The level of the internal uart txd value*/
|
||
#define UART_TXD (BIT(31))
|
||
#define UART_TXD_M (BIT(31))
|
||
#define UART_TXD_V 0x1
|
||
#define UART_TXD_S 31
|
||
/* UART_RTSN : RO ;bitpos:[30] ;default: 1'b0 ; */
|
||
/*description: The level of the internal uart rts pin*/
|
||
#define UART_RTSN (BIT(30))
|
||
#define UART_RTSN_M (BIT(30))
|
||
#define UART_RTSN_V 0x1
|
||
#define UART_RTSN_S 30
|
||
/* UART_DTRN : RO ;bitpos:[29] ;default: 1'b0 ; */
|
||
/*description: The level of the internaluart dtr pin*/
|
||
#define UART_DTRN (BIT(29))
|
||
#define UART_DTRN_M (BIT(29))
|
||
#define UART_DTRN_V 0x1
|
||
#define UART_DTRN_S 29
|
||
/* UART_ST_UTX_OUT : RO ;bitpos:[27:24] ;default: 4'b0 ; */
|
||
/*description: The state for transmitting data. 4'd0:TX_IDLE*/
|
||
#define UART_ST_UTX_OUT 0x0000000F
|
||
#define UART_ST_UTX_OUT_M ((UART_ST_UTX_OUT_V)<<(UART_ST_UTX_OUT_S))
|
||
#define UART_ST_UTX_OUT_V 0xF
|
||
#define UART_ST_UTX_OUT_S 24
|
||
/* UART_TXFIFO_CNT : RO ;bitpos:[23:16] ;default: 8'b0 ; */
|
||
/*description: Number of data in UART TX fifo*/
|
||
#define UART_TXFIFO_CNT 0x000000FF
|
||
#define UART_TXFIFO_CNT_M ((UART_TXFIFO_CNT_V)<<(UART_TXFIFO_CNT_S))
|
||
#define UART_TXFIFO_CNT_V 0xFF
|
||
#define UART_TXFIFO_CNT_S 16
|
||
/* UART_RXD : RO ;bitpos:[15] ;default: 1'b0 ; */
|
||
/*description: The level of the internal uart rxd value*/
|
||
#define UART_RXD (BIT(15))
|
||
#define UART_RXD_M (BIT(15))
|
||
#define UART_RXD_V 0x1
|
||
#define UART_RXD_S 15
|
||
/* UART_CTSN : RO ;bitpos:[14] ;default: 1'b0 ; */
|
||
/*description: The level of the internal uart cts value*/
|
||
#define UART_CTSN (BIT(14))
|
||
#define UART_CTSN_M (BIT(14))
|
||
#define UART_CTSN_V 0x1
|
||
#define UART_CTSN_S 14
|
||
/* UART_DSRN : RO ;bitpos:[13] ;default: 1'b0 ; */
|
||
/*description: The level of the internal uart dsr value*/
|
||
#define UART_DSRN (BIT(13))
|
||
#define UART_DSRN_M (BIT(13))
|
||
#define UART_DSRN_V 0x1
|
||
#define UART_DSRN_S 13
|
||
/* UART_ST_URX_OUT : RO ;bitpos:[11:8] ;default: 4'b0 ; */
|
||
/*description: The state for receiving data. 4‘d0: RX_IDLE*/
|
||
#define UART_ST_URX_OUT 0x0000000F
|
||
#define UART_ST_URX_OUT_M ((UART_ST_URX_OUT_V)<<(UART_ST_URX_OUT_S))
|
||
#define UART_ST_URX_OUT_V 0xF
|
||
#define UART_ST_URX_OUT_S 8
|
||
/* UART_RXFIFO_CNT : RO ;bitpos:[7:0] ;default: 8'b0 ; */
|
||
/*description: Number of data in UART RX fifo*/
|
||
#define UART_RXFIFO_CNT 0x000000FF
|
||
#define UART_RXFIFO_CNT_M ((UART_RXFIFO_CNT_V)<<(UART_RXFIFO_CNT_S))
|
||
#define UART_RXFIFO_CNT_V 0xFF
|
||
#define UART_RXFIFO_CNT_S 0
|
||
#define UART_GET_TXD(i) GET_PERI_REG_BITS2(UART_STATUS_REG(i) , UART_TXD_V, UART_TXD_S)
|
||
#define UART_GET_RTSN(i) GET_PERI_REG_BITS2(UART_STATUS_REG(i) , UART_RTSN_V, UART_RTSN_S)
|
||
#define UART_GET_DTRN(i) GET_PERI_REG_BITS2(UART_STATUS_REG(i) , UART_DTRN_V, UART_DTRN_S)
|
||
#define UART_GET_ST_UTX_OUT(i) GET_PERI_REG_BITS2(UART_STATUS_REG(i) , UART_ST_UTX_OUT_V, UART_ST_UTX_OUT_S)
|
||
#define UART_GET_TXFIFO_CNT(i) GET_PERI_REG_BITS2(UART_STATUS_REG(i) , UART_TXFIFO_CNT_V, UART_TXFIFO_CNT_S)
|
||
#define UART_GET_RXD(i) GET_PERI_REG_BITS2(UART_STATUS_REG(i) , UART_RXD_V, UART_RXD_S)
|
||
#define UART_GET_CTSN(i) GET_PERI_REG_BITS2(UART_STATUS_REG(i) , UART_CTSN_V, UART_CTSN_S)
|
||
#define UART_GET_DSRN(i) GET_PERI_REG_BITS2(UART_STATUS_REG(i) , UART_DSRN_V, UART_DSRN_S)
|
||
#define UART_GET_ST_URX_OUT(i) GET_PERI_REG_BITS2(UART_STATUS_REG(i) , UART_ST_URX_OUT_V, UART_ST_URX_OUT_S)
|
||
#define UART_GET_RXFIFO_CNT(i) GET_PERI_REG_BITS2(UART_STATUS_REG(i) , UART_RXFIFO_CNT_V, UART_RXFIFO_CNT_S)
|
||
|
||
|
||
|
||
#define UART_CONF0_REG(i) (REG_UART_BASE(i) + 0x20)
|
||
/* UART_TICK_REF_ALWAYS_ON : R/W ;bitpos:[27] ;default: 1'b1 ; */
|
||
/*description: 1：use apb clock：use referrence clock*/
|
||
#define UART_TICK_REF_ALWAYS_ON (BIT(27))
|
||
#define UART_TICK_REF_ALWAYS_ON_M (BIT(27))
|
||
#define UART_TICK_REF_ALWAYS_ON_V 0x1
|
||
#define UART_TICK_REF_ALWAYS_ON_S 27
|
||
/* UART_ERR_WR_MASK : R/W ;bitpos:[26] ;default: 1'b0 ; */
|
||
/*description: 1：rx stop storing data int rxfifo when data is error 0：if received data is wrong*/
|
||
#define UART_ERR_WR_MASK (BIT(26))
|
||
#define UART_ERR_WR_MASK_M (BIT(26))
|
||
#define UART_ERR_WR_MASK_V 0x1
|
||
#define UART_ERR_WR_MASK_S 26
|
||
/* UART_CLK_EN : R/W ;bitpos:[25] ;default: 1'h0 ; */
|
||
/*description: 1：force clock on for registers：support clock only when write registers*/
|
||
#define UART_CLK_EN (BIT(25))
|
||
#define UART_CLK_EN_M (BIT(25))
|
||
#define UART_CLK_EN_V 0x1
|
||
#define UART_CLK_EN_S 25
|
||
/* UART_DTR_INV : R/W ;bitpos:[24] ;default: 1'h0 ; */
|
||
/*description: Set this bit to inverse uart dtr level*/
|
||
#define UART_DTR_INV (BIT(24))
|
||
#define UART_DTR_INV_M (BIT(24))
|
||
#define UART_DTR_INV_V 0x1
|
||
#define UART_DTR_INV_S 24
|
||
/* UART_RTS_INV : R/W ;bitpos:[23] ;default: 1'h0 ; */
|
||
/*description: Set this bit to inverse uart rts level*/
|
||
#define UART_RTS_INV (BIT(23))
|
||
#define UART_RTS_INV_M (BIT(23))
|
||
#define UART_RTS_INV_V 0x1
|
||
#define UART_RTS_INV_S 23
|
||
/* UART_TXD_INV : R/W ;bitpos:[22] ;default: 1'h0 ; */
|
||
/*description: Set this bit to inverse uart txd level*/
|
||
#define UART_TXD_INV (BIT(22))
|
||
#define UART_TXD_INV_M (BIT(22))
|
||
#define UART_TXD_INV_V 0x1
|
||
#define UART_TXD_INV_S 22
|
||
/* UART_DSR_INV : R/W ;bitpos:[21] ;default: 1'h0 ; */
|
||
/*description: Set this bit to inverse uart dsr level*/
|
||
#define UART_DSR_INV (BIT(21))
|
||
#define UART_DSR_INV_M (BIT(21))
|
||
#define UART_DSR_INV_V 0x1
|
||
#define UART_DSR_INV_S 21
|
||
/* UART_CTS_INV : R/W ;bitpos:[20] ;default: 1'h0 ; */
|
||
/*description: Set this bit to inverse uart cts level*/
|
||
#define UART_CTS_INV (BIT(20))
|
||
#define UART_CTS_INV_M (BIT(20))
|
||
#define UART_CTS_INV_V 0x1
|
||
#define UART_CTS_INV_S 20
|
||
/* UART_RXD_INV : R/W ;bitpos:[19] ;default: 1'h0 ; */
|
||
/*description: Set this bit to inverse uart rxd level*/
|
||
#define UART_RXD_INV (BIT(19))
|
||
#define UART_RXD_INV_M (BIT(19))
|
||
#define UART_RXD_INV_V 0x1
|
||
#define UART_RXD_INV_S 19
|
||
/* UART_TXFIFO_RST : R/W ;bitpos:[18] ;default: 1'h0 ; */
|
||
/*description: Set this bit to reset uart tx fifo*/
|
||
#define UART_TXFIFO_RST (BIT(18))
|
||
#define UART_TXFIFO_RST_M (BIT(18))
|
||
#define UART_TXFIFO_RST_V 0x1
|
||
#define UART_TXFIFO_RST_S 18
|
||
/* UART_RXFIFO_RST : R/W ;bitpos:[17] ;default: 1'h0 ; */
|
||
/*description: Set this bit to reset uart rx fifo*/
|
||
#define UART_RXFIFO_RST (BIT(17))
|
||
#define UART_RXFIFO_RST_M (BIT(17))
|
||
#define UART_RXFIFO_RST_V 0x1
|
||
#define UART_RXFIFO_RST_S 17
|
||
/* UART_IRDA_EN : R/W ;bitpos:[16] ;default: 1'h0 ; */
|
||
/*description: Set this bit to enable irda protocol*/
|
||
#define UART_IRDA_EN (BIT(16))
|
||
#define UART_IRDA_EN_M (BIT(16))
|
||
#define UART_IRDA_EN_V 0x1
|
||
#define UART_IRDA_EN_S 16
|
||
/* UART_TX_FLOW_EN : R/W ;bitpos:[15] ;default: 1'b0 ; */
|
||
/*description: Set this bit to enable tx flow control*/
|
||
#define UART_TX_FLOW_EN (BIT(15))
|
||
#define UART_TX_FLOW_EN_M (BIT(15))
|
||
#define UART_TX_FLOW_EN_V 0x1
|
||
#define UART_TX_FLOW_EN_S 15
|
||
/* UART_LOOPBACK : R/W ;bitpos:[14] ;default: 1'b0 ; */
|
||
/*description: Set this bit to enable uart loopback test mode*/
|
||
#define UART_LOOPBACK (BIT(14))
|
||
#define UART_LOOPBACK_M (BIT(14))
|
||
#define UART_LOOPBACK_V 0x1
|
||
#define UART_LOOPBACK_S 14
|
||
/* UART_IRDA_RX_INV : R/W ;bitpos:[13] ;default: 1'b0 ; */
|
||
/*description: Set this bit to inverse irda rx level*/
|
||
#define UART_IRDA_RX_INV (BIT(13))
|
||
#define UART_IRDA_RX_INV_M (BIT(13))
|
||
#define UART_IRDA_RX_INV_V 0x1
|
||
#define UART_IRDA_RX_INV_S 13
|
||
/* UART_IRDA_TX_INV : R/W ;bitpos:[12] ;default: 1'b0 ; */
|
||
/*description: Set this bit to inverse irda tx level*/
|
||
#define UART_IRDA_TX_INV (BIT(12))
|
||
#define UART_IRDA_TX_INV_M (BIT(12))
|
||
#define UART_IRDA_TX_INV_V 0x1
|
||
#define UART_IRDA_TX_INV_S 12
|
||
/* UART_IRDA_WCTL : R/W ;bitpos:[11] ;default: 1'b0 ; */
|
||
/*description: 1：the tx 11th bit is the same to the 10th bit 0：set tx 11th bit to 0*/
|
||
#define UART_IRDA_WCTL (BIT(11))
|
||
#define UART_IRDA_WCTL_M (BIT(11))
|
||
#define UART_IRDA_WCTL_V 0x1
|
||
#define UART_IRDA_WCTL_S 11
|
||
/* UART_IRDA_TX_EN : R/W ;bitpos:[10] ;default: 1'b0 ; */
|
||
/*description: Set this bit to enable irda to send data*/
|
||
#define UART_IRDA_TX_EN (BIT(10))
|
||
#define UART_IRDA_TX_EN_M (BIT(10))
|
||
#define UART_IRDA_TX_EN_V 0x1
|
||
#define UART_IRDA_TX_EN_S 10
|
||
/* UART_IRDA_DPLX : R/W ;bitpos:[9] ;default: 1'b0 ; */
|
||
/*description: Set this bit to enable irda duplex mode*/
|
||
#define UART_IRDA_DPLX (BIT(9))
|
||
#define UART_IRDA_DPLX_M (BIT(9))
|
||
#define UART_IRDA_DPLX_V 0x1
|
||
#define UART_IRDA_DPLX_S 9
|
||
/* UART_TXD_BRK : R/W ;bitpos:[8] ;default: 1'b0 ; */
|
||
/*description: Set this bit to enbale tx send 0*/
|
||
#define UART_TXD_BRK (BIT(8))
|
||
#define UART_TXD_BRK_M (BIT(8))
|
||
#define UART_TXD_BRK_V 0x1
|
||
#define UART_TXD_BRK_S 8
|
||
/* UART_SW_DTR : R/W ;bitpos:[7] ;default: 1'b0 ; */
|
||
/*description: sw dtr*/
|
||
#define UART_SW_DTR (BIT(7))
|
||
#define UART_SW_DTR_M (BIT(7))
|
||
#define UART_SW_DTR_V 0x1
|
||
#define UART_SW_DTR_S 7
|
||
/* UART_SW_RTS : R/W ;bitpos:[6] ;default: 1'b0 ; */
|
||
/*description: sw rts*/
|
||
#define UART_SW_RTS (BIT(6))
|
||
#define UART_SW_RTS_M (BIT(6))
|
||
#define UART_SW_RTS_V 0x1
|
||
#define UART_SW_RTS_S 6
|
||
/* UART_STOP_BIT_NUM : R/W ;bitpos:[5:4] ;default: 2'd1 ; */
|
||
/*description: Set stop bit: 1:1bit 2:1.5bits 3:2bits*/
|
||
#define UART_STOP_BIT_NUM 0x00000003
|
||
#define UART_STOP_BIT_NUM_M ((UART_STOP_BIT_NUM_V)<<(UART_STOP_BIT_NUM_S))
|
||
#define UART_STOP_BIT_NUM_V 0x3
|
||
#define UART_STOP_BIT_NUM_S 4
|
||
/* UART_BIT_NUM : R/W ;bitpos:[3:2] ;default: 2'd3 ; */
|
||
/*description: Set bit num: 0:5bits 1:6bits 2:7bits 3:8bits*/
|
||
#define UART_BIT_NUM 0x00000003
|
||
#define UART_BIT_NUM_M ((UART_BIT_NUM_V)<<(UART_BIT_NUM_S))
|
||
#define UART_BIT_NUM_V 0x3
|
||
#define UART_BIT_NUM_S 2
|
||
/* UART_PARITY_EN : R/W ;bitpos:[1] ;default: 1'b0 ; */
|
||
/*description: Set this bit to enable uart parity check*/
|
||
#define UART_PARITY_EN (BIT(1))
|
||
#define UART_PARITY_EN_M (BIT(1))
|
||
#define UART_PARITY_EN_V 0x1
|
||
#define UART_PARITY_EN_S 1
|
||
/* UART_PARITY : R/W ;bitpos:[0] ;default: 1'b0 ; */
|
||
/*description: Set parity check: 0:even 1:odd*/
|
||
#define UART_PARITY (BIT(0))
|
||
#define UART_PARITY_M (BIT(0))
|
||
#define UART_PARITY_V 0x1
|
||
#define UART_PARITY_S 0
|
||
#define UART_GET_TICK_REF_ALWAYS_ON(i) GET_PERI_REG_BITS2(UART_CONF0_REG(i) , UART_TICK_REF_ALWAYS_ON_V, UART_TICK_REF_ALWAYS_ON_S)
|
||
#define UART_SET_TICK_REF_ALWAYS_ON(i,val) SET_PERI_REG_BITS(UART_CONF0_REG(i) ,UART_TICK_REF_ALWAYS_ON_V,(val),UART_TICK_REF_ALWAYS_ON_S)
|
||
#define UART_GET_ERR_WR_MASK(i) GET_PERI_REG_BITS2(UART_CONF0_REG(i) , UART_ERR_WR_MASK_V, UART_ERR_WR_MASK_S)
|
||
#define UART_SET_ERR_WR_MASK(i,val) SET_PERI_REG_BITS(UART_CONF0_REG(i) ,UART_ERR_WR_MASK_V,(val),UART_ERR_WR_MASK_S)
|
||
#define UART_GET_REG_CLK_EN(i) GET_PERI_REG_BITS2(UART_CONF0_REG(i) , UART_CLK_EN_V, UART_CLK_EN_S)
|
||
#define UART_SET_REG_CLK_EN(i,val) SET_PERI_REG_BITS(UART_CONF0_REG(i) ,UART_CLK_EN_V,(val),UART_CLK_EN_S)
|
||
#define UART_GET_DTR_INV(i) GET_PERI_REG_BITS2(UART_CONF0_REG(i) , UART_DTR_INV_V, UART_DTR_INV_S)
|
||
#define UART_SET_DTR_INV(i,val) SET_PERI_REG_BITS(UART_CONF0_REG(i) ,UART_DTR_INV_V,(val),UART_DTR_INV_S)
|
||
#define UART_GET_RTS_INV(i) GET_PERI_REG_BITS2(UART_CONF0_REG(i) , UART_RTS_INV_V, UART_RTS_INV_S)
|
||
#define UART_SET_RTS_INV(i,val) SET_PERI_REG_BITS(UART_CONF0_REG(i) ,UART_RTS_INV_V,(val),UART_RTS_INV_S)
|
||
#define UART_GET_TXD_INV(i) GET_PERI_REG_BITS2(UART_CONF0_REG(i) , UART_TXD_INV_V, UART_TXD_INV_S)
|
||
#define UART_SET_TXD_INV(i,val) SET_PERI_REG_BITS(UART_CONF0_REG(i) ,UART_TXD_INV_V,(val),UART_TXD_INV_S)
|
||
#define UART_GET_DSR_INV(i) GET_PERI_REG_BITS2(UART_CONF0_REG(i) , UART_DSR_INV_V, UART_DSR_INV_S)
|
||
#define UART_SET_DSR_INV(i,val) SET_PERI_REG_BITS(UART_CONF0_REG(i) ,UART_DSR_INV_V,(val),UART_DSR_INV_S)
|
||
#define UART_GET_CTS_INV(i) GET_PERI_REG_BITS2(UART_CONF0_REG(i) , UART_CTS_INV_V, UART_CTS_INV_S)
|
||
#define UART_SET_CTS_INV(i,val) SET_PERI_REG_BITS(UART_CONF0_REG(i) ,UART_CTS_INV_V,(val),UART_CTS_INV_S)
|
||
#define UART_GET_RXD_INV(i) GET_PERI_REG_BITS2(UART_CONF0_REG(i) , UART_RXD_INV_V, UART_RXD_INV_S)
|
||
#define UART_SET_RXD_INV(i,val) SET_PERI_REG_BITS(UART_CONF0_REG(i) ,UART_RXD_INV_V,(val),UART_RXD_INV_S)
|
||
#define UART_GET_TXFIFO_RST(i) GET_PERI_REG_BITS2(UART_CONF0_REG(i) , UART_TXFIFO_RST_V, UART_TXFIFO_RST_S)
|
||
#define UART_SET_TXFIFO_RST(i,val) SET_PERI_REG_BITS(UART_CONF0_REG(i) ,UART_TXFIFO_RST_V,(val),UART_TXFIFO_RST_S)
|
||
#define UART_GET_RXFIFO_RST(i) GET_PERI_REG_BITS2(UART_CONF0_REG(i) , UART_RXFIFO_RST_V, UART_RXFIFO_RST_S)
|
||
#define UART_SET_RXFIFO_RST(i,val) SET_PERI_REG_BITS(UART_CONF0_REG(i) ,UART_RXFIFO_RST_V,(val),UART_RXFIFO_RST_S)
|
||
#define UART_GET_IRDA_EN(i) GET_PERI_REG_BITS2(UART_CONF0_REG(i) , UART_IRDA_EN_V, UART_IRDA_EN_S)
|
||
#define UART_SET_IRDA_EN(i,val) SET_PERI_REG_BITS(UART_CONF0_REG(i) ,UART_IRDA_EN_V,(val),UART_IRDA_EN_S)
|
||
#define UART_GET_TX_FLOW_EN(i) GET_PERI_REG_BITS2(UART_CONF0_REG(i) , UART_TX_FLOW_EN_V, UART_TX_FLOW_EN_S)
|
||
#define UART_SET_TX_FLOW_EN(i,val) SET_PERI_REG_BITS(UART_CONF0_REG(i) ,UART_TX_FLOW_EN_V,(val),UART_TX_FLOW_EN_S)
|
||
#define UART_GET_LOOPBACK(i) GET_PERI_REG_BITS2(UART_CONF0_REG(i) , UART_LOOPBACK_V, UART_LOOPBACK_S)
|
||
#define UART_SET_LOOPBACK(i,val) SET_PERI_REG_BITS(UART_CONF0_REG(i) ,UART_LOOPBACK_V,(val),UART_LOOPBACK_S)
|
||
#define UART_GET_IRDA_RX_INV(i) GET_PERI_REG_BITS2(UART_CONF0_REG(i) , UART_IRDA_RX_INV_V, UART_IRDA_RX_INV_S)
|
||
#define UART_SET_IRDA_RX_INV(i,val) SET_PERI_REG_BITS(UART_CONF0_REG(i) ,UART_IRDA_RX_INV_V,(val),UART_IRDA_RX_INV_S)
|
||
#define UART_GET_IRDA_TX_INV(i) GET_PERI_REG_BITS2(UART_CONF0_REG(i) , UART_IRDA_TX_INV_V, UART_IRDA_TX_INV_S)
|
||
#define UART_SET_IRDA_TX_INV(i,val) SET_PERI_REG_BITS(UART_CONF0_REG(i) ,UART_IRDA_TX_INV_V,(val),UART_IRDA_TX_INV_S)
|
||
#define UART_GET_IRDA_WCTL(i) GET_PERI_REG_BITS2(UART_CONF0_REG(i) , UART_IRDA_WCTL_V, UART_IRDA_WCTL_S)
|
||
#define UART_SET_IRDA_WCTL(i,val) SET_PERI_REG_BITS(UART_CONF0_REG(i) ,UART_IRDA_WCTL_V,(val),UART_IRDA_WCTL_S)
|
||
#define UART_GET_IRDA_TX_EN(i) GET_PERI_REG_BITS2(UART_CONF0_REG(i) , UART_IRDA_TX_EN_V, UART_IRDA_TX_EN_S)
|
||
#define UART_SET_IRDA_TX_EN(i,val) SET_PERI_REG_BITS(UART_CONF0_REG(i) ,UART_IRDA_TX_EN_V,(val),UART_IRDA_TX_EN_S)
|
||
#define UART_GET_IRDA_DPLX(i) GET_PERI_REG_BITS2(UART_CONF0_REG(i) , UART_IRDA_DPLX_V, UART_IRDA_DPLX_S)
|
||
#define UART_SET_IRDA_DPLX(i,val) SET_PERI_REG_BITS(UART_CONF0_REG(i) ,UART_IRDA_DPLX_V,(val),UART_IRDA_DPLX_S)
|
||
#define UART_GET_TXD_BRK(i) GET_PERI_REG_BITS2(UART_CONF0_REG(i) , UART_TXD_BRK_V, UART_TXD_BRK_S)
|
||
#define UART_SET_TXD_BRK(i,val) SET_PERI_REG_BITS(UART_CONF0_REG(i) ,UART_TXD_BRK_V,(val),UART_TXD_BRK_S)
|
||
#define UART_GET_SW_DTR(i) GET_PERI_REG_BITS2(UART_CONF0_REG(i) , UART_SW_DTR_V, UART_SW_DTR_S)
|
||
#define UART_SET_SW_DTR(i,val) SET_PERI_REG_BITS(UART_CONF0_REG(i) ,UART_SW_DTR_V,(val),UART_SW_DTR_S)
|
||
#define UART_GET_SW_RTS(i) GET_PERI_REG_BITS2(UART_CONF0_REG(i) , UART_SW_RTS_V, UART_SW_RTS_S)
|
||
#define UART_SET_SW_RTS(i,val) SET_PERI_REG_BITS(UART_CONF0_REG(i) ,UART_SW_RTS_V,(val),UART_SW_RTS_S)
|
||
#define UART_GET_STOP_BIT_NUM(i) GET_PERI_REG_BITS2(UART_CONF0_REG(i) , UART_STOP_BIT_NUM_V, UART_STOP_BIT_NUM_S)
|
||
#define UART_SET_STOP_BIT_NUM(i,val) SET_PERI_REG_BITS(UART_CONF0_REG(i) ,UART_STOP_BIT_NUM_V,(val),UART_STOP_BIT_NUM_S)
|
||
#define UART_GET_BIT_NUM(i) GET_PERI_REG_BITS2(UART_CONF0_REG(i) , UART_BIT_NUM_V, UART_BIT_NUM_S)
|
||
#define UART_SET_BIT_NUM(i,val) SET_PERI_REG_BITS(UART_CONF0_REG(i) ,UART_BIT_NUM_V,(val),UART_BIT_NUM_S)
|
||
#define UART_GET_PARITY_EN(i) GET_PERI_REG_BITS2(UART_CONF0_REG(i) , UART_PARITY_EN_V, UART_PARITY_EN_S)
|
||
#define UART_SET_PARITY_EN(i,val) SET_PERI_REG_BITS(UART_CONF0_REG(i) ,UART_PARITY_EN_V,(val),UART_PARITY_EN_S)
|
||
#define UART_GET_PARITY(i) GET_PERI_REG_BITS2(UART_CONF0_REG(i) , UART_PARITY_V, UART_PARITY_S)
|
||
#define UART_SET_PARITY(i,val) SET_PERI_REG_BITS(UART_CONF0_REG(i) ,UART_PARITY_V,(val),UART_PARITY_S)
|
||
|
||
|
||
|
||
#define UART_CONF1_REG(i) (REG_UART_BASE(i) + 0x24)
|
||
/* UART_RX_TOUT_EN : R/W ;bitpos:[31] ;default: 1'b0 ; */
|
||
/*description: Set this bit to enable rx time-out function*/
|
||
#define UART_RX_TOUT_EN (BIT(31))
|
||
#define UART_RX_TOUT_EN_M (BIT(31))
|
||
#define UART_RX_TOUT_EN_V 0x1
|
||
#define UART_RX_TOUT_EN_S 31
|
||
/* UART_RX_TOUT_THRHD : R/W ;bitpos:[30:24] ;default: 7'b0 ; */
|
||
/*description: Config bits for rx time-out threshold*/
|
||
#define UART_RX_TOUT_THRHD 0x0000007F
|
||
#define UART_RX_TOUT_THRHD_M ((UART_RX_TOUT_THRHD_V)<<(UART_RX_TOUT_THRHD_S))
|
||
#define UART_RX_TOUT_THRHD_V 0x7F
|
||
#define UART_RX_TOUT_THRHD_S 24
|
||
/* UART_RX_FLOW_EN : R/W ;bitpos:[23] ;default: 1'b0 ; */
|
||
/*description: Set this bit to enable rx hardware flow control*/
|
||
#define UART_RX_FLOW_EN (BIT(23))
|
||
#define UART_RX_FLOW_EN_M (BIT(23))
|
||
#define UART_RX_FLOW_EN_V 0x1
|
||
#define UART_RX_FLOW_EN_S 23
|
||
/* UART_RX_FLOW_THRHD : R/W ;bitpos:[22:16] ;default: 7'h0 ; */
|
||
/*description: The config bits for rx flow control threshold*/
|
||
#define UART_RX_FLOW_THRHD 0x0000007F
|
||
#define UART_RX_FLOW_THRHD_M ((UART_RX_FLOW_THRHD_V)<<(UART_RX_FLOW_THRHD_S))
|
||
#define UART_RX_FLOW_THRHD_V 0x7F
|
||
#define UART_RX_FLOW_THRHD_S 16
|
||
/* UART_TXFIFO_EMPTY_THRHD : R/W ;bitpos:[14:8] ;default: 7'h60 ; */
|
||
/*description: The config bits for tx fifo empty threshold*/
|
||
#define UART_TXFIFO_EMPTY_THRHD 0x0000007F
|
||
#define UART_TXFIFO_EMPTY_THRHD_M ((UART_TXFIFO_EMPTY_THRHD_V)<<(UART_TXFIFO_EMPTY_THRHD_S))
|
||
#define UART_TXFIFO_EMPTY_THRHD_V 0x7F
|
||
#define UART_TXFIFO_EMPTY_THRHD_S 8
|
||
/* UART_RXFIFO_FULL_THRHD : R/W ;bitpos:[6:0] ;default: 7'h60 ; */
|
||
/*description: The config bits for rx fifo full threshold*/
|
||
#define UART_RXFIFO_FULL_THRHD 0x0000007F
|
||
#define UART_RXFIFO_FULL_THRHD_M ((UART_RXFIFO_FULL_THRHD_V)<<(UART_RXFIFO_FULL_THRHD_S))
|
||
#define UART_RXFIFO_FULL_THRHD_V 0x7F
|
||
#define UART_RXFIFO_FULL_THRHD_S 0
|
||
#define UART_GET_RX_TOUT_EN(i) GET_PERI_REG_BITS2(UART_CONF1_REG(i) , UART_RX_TOUT_EN_V, UART_RX_TOUT_EN_S)
|
||
#define UART_SET_RX_TOUT_EN(i,val) SET_PERI_REG_BITS(UART_CONF1_REG(i) ,UART_RX_TOUT_EN_V,(val),UART_RX_TOUT_EN_S)
|
||
#define UART_GET_RX_TOUT_THRHD(i) GET_PERI_REG_BITS2(UART_CONF1_REG(i) , UART_RX_TOUT_THRHD_V, UART_RX_TOUT_THRHD_S)
|
||
#define UART_SET_RX_TOUT_THRHD(i,val) SET_PERI_REG_BITS(UART_CONF1_REG(i) ,UART_RX_TOUT_THRHD_V,(val),UART_RX_TOUT_THRHD_S)
|
||
#define UART_GET_RX_FLOW_EN(i) GET_PERI_REG_BITS2(UART_CONF1_REG(i) , UART_RX_FLOW_EN_V, UART_RX_FLOW_EN_S)
|
||
#define UART_SET_RX_FLOW_EN(i,val) SET_PERI_REG_BITS(UART_CONF1_REG(i) ,UART_RX_FLOW_EN_V,(val),UART_RX_FLOW_EN_S)
|
||
#define UART_GET_RX_FLOW_THRHD(i) GET_PERI_REG_BITS2(UART_CONF1_REG(i) , UART_RX_FLOW_THRHD_V, UART_RX_FLOW_THRHD_S)
|
||
#define UART_SET_RX_FLOW_THRHD(i,val) SET_PERI_REG_BITS(UART_CONF1_REG(i) ,UART_RX_FLOW_THRHD_V,(val),UART_RX_FLOW_THRHD_S)
|
||
#define UART_GET_TXFIFO_EMPTY_THRHD(i) GET_PERI_REG_BITS2(UART_CONF1_REG(i) , UART_TXFIFO_EMPTY_THRHD_V, UART_TXFIFO_EMPTY_THRHD_S)
|
||
#define UART_SET_TXFIFO_EMPTY_THRHD(i,val) SET_PERI_REG_BITS(UART_CONF1_REG(i) ,UART_TXFIFO_EMPTY_THRHD_V,(val),UART_TXFIFO_EMPTY_THRHD_S)
|
||
#define UART_GET_RXFIFO_FULL_THRHD(i) GET_PERI_REG_BITS2(UART_CONF1_REG(i) , UART_RXFIFO_FULL_THRHD_V, UART_RXFIFO_FULL_THRHD_S)
|
||
#define UART_SET_RXFIFO_FULL_THRHD(i,val) SET_PERI_REG_BITS(UART_CONF1_REG(i) ,UART_RXFIFO_FULL_THRHD_V,(val),UART_RXFIFO_FULL_THRHD_S)
|
||
|
||
|
||
|
||
#define UART_LOWPULSE_REG(i) (REG_UART_BASE(i) + 0x28)
|
||
/* UART_LOWPULSE_MIN_CNT : RO ;bitpos:[19:0] ;default: 20'hFFFFF ; */
|
||
/*description: used in baudrate detect*/
|
||
#define UART_LOWPULSE_MIN_CNT 0x000FFFFF
|
||
#define UART_LOWPULSE_MIN_CNT_M ((UART_LOWPULSE_MIN_CNT_V)<<(UART_LOWPULSE_MIN_CNT_S))
|
||
#define UART_LOWPULSE_MIN_CNT_V 0xFFFFF
|
||
#define UART_LOWPULSE_MIN_CNT_S 0
|
||
#define UART_GET_LOWPULSE_MIN_CNT(i) GET_PERI_REG_BITS2(UART_LOWPULSE_REG(i) , UART_LOWPULSE_MIN_CNT_V, UART_LOWPULSE_MIN_CNT_S)
|
||
|
||
|
||
|
||
#define UART_HIGHPULSE_REG(i) (REG_UART_BASE(i) + 0x2C)
|
||
/* UART_HIGHPULSE_MIN_CNT : RO ;bitpos:[19:0] ;default: 20'hFFFFF ; */
|
||
/*description: used in baudrate detect*/
|
||
#define UART_HIGHPULSE_MIN_CNT 0x000FFFFF
|
||
#define UART_HIGHPULSE_MIN_CNT_M ((UART_HIGHPULSE_MIN_CNT_V)<<(UART_HIGHPULSE_MIN_CNT_S))
|
||
#define UART_HIGHPULSE_MIN_CNT_V 0xFFFFF
|
||
#define UART_HIGHPULSE_MIN_CNT_S 0
|
||
#define UART_GET_HIGHPULSE_MIN_CNT(i) GET_PERI_REG_BITS2(UART_HIGHPULSE_REG(i) , UART_HIGHPULSE_MIN_CNT_V, UART_HIGHPULSE_MIN_CNT_S)
|
||
|
||
|
||
|
||
#define UART_RXD_CNT_REG(i) (REG_UART_BASE(i) + 0x30)
|
||
/* UART_RXD_EDGE_CNT : RO ;bitpos:[9:0] ;default: 10'h0 ; */
|
||
/*description: used in baudrate detect*/
|
||
#define UART_RXD_EDGE_CNT 0x000003FF
|
||
#define UART_RXD_EDGE_CNT_M ((UART_RXD_EDGE_CNT_V)<<(UART_RXD_EDGE_CNT_S))
|
||
#define UART_RXD_EDGE_CNT_V 0x3FF
|
||
#define UART_RXD_EDGE_CNT_S 0
|
||
#define UART_GET_RXD_EDGE_CNT(i) GET_PERI_REG_BITS2(UART_RXD_CNT_REG(i) , UART_RXD_EDGE_CNT_V, UART_RXD_EDGE_CNT_S)
|
||
|
||
|
||
|
||
#define UART_FLOW_CONF_REG(i) (REG_UART_BASE(i) + 0x34)
|
||
/* UART_SEND_XOFF : R/W ;bitpos:[5] ;default: 1'b0 ; */
|
||
/*description: */
|
||
#define UART_SEND_XOFF (BIT(5))
|
||
#define UART_SEND_XOFF_M (BIT(5))
|
||
#define UART_SEND_XOFF_V 0x1
|
||
#define UART_SEND_XOFF_S 5
|
||
/* UART_SEND_XON : R/W ;bitpos:[4] ;default: 1'b0 ; */
|
||
/*description: */
|
||
#define UART_SEND_XON (BIT(4))
|
||
#define UART_SEND_XON_M (BIT(4))
|
||
#define UART_SEND_XON_V 0x1
|
||
#define UART_SEND_XON_S 4
|
||
/* UART_FORCE_XOFF : R/W ;bitpos:[3] ;default: 1'b0 ; */
|
||
/*description: Set this bit to set ctsn*/
|
||
#define UART_FORCE_XOFF (BIT(3))
|
||
#define UART_FORCE_XOFF_M (BIT(3))
|
||
#define UART_FORCE_XOFF_V 0x1
|
||
#define UART_FORCE_XOFF_S 3
|
||
/* UART_FORCE_XON : R/W ;bitpos:[2] ;default: 1'b0 ; */
|
||
/*description: Set this bit to clear ctsn*/
|
||
#define UART_FORCE_XON (BIT(2))
|
||
#define UART_FORCE_XON_M (BIT(2))
|
||
#define UART_FORCE_XON_V 0x1
|
||
#define UART_FORCE_XON_S 2
|
||
/* UART_XONOFF_DEL : R/W ;bitpos:[1] ;default: 1'b0 ; */
|
||
/*description: Set this bit to remove flow control char from rx data*/
|
||
#define UART_XONOFF_DEL (BIT(1))
|
||
#define UART_XONOFF_DEL_M (BIT(1))
|
||
#define UART_XONOFF_DEL_V 0x1
|
||
#define UART_XONOFF_DEL_S 1
|
||
/* UART_SW_FLOW_CON_EN : R/W ;bitpos:[0] ;default: 1'b0 ; */
|
||
/*description: Set this bit to enable sw flow control*/
|
||
#define UART_SW_FLOW_CON_EN (BIT(0))
|
||
#define UART_SW_FLOW_CON_EN_M (BIT(0))
|
||
#define UART_SW_FLOW_CON_EN_V 0x1
|
||
#define UART_SW_FLOW_CON_EN_S 0
|
||
#define UART_GET_SEND_XOFF(i) GET_PERI_REG_BITS2(UART_FLOW_CONF_REG(i) , UART_SEND_XOFF_V, UART_SEND_XOFF_S)
|
||
#define UART_SET_SEND_XOFF(i,val) SET_PERI_REG_BITS(UART_FLOW_CONF_REG(i) ,UART_SEND_XOFF_V,(val),UART_SEND_XOFF_S)
|
||
#define UART_GET_SEND_XON(i) GET_PERI_REG_BITS2(UART_FLOW_CONF_REG(i) , UART_SEND_XON_V, UART_SEND_XON_S)
|
||
#define UART_SET_SEND_XON(i,val) SET_PERI_REG_BITS(UART_FLOW_CONF_REG(i) ,UART_SEND_XON_V,(val),UART_SEND_XON_S)
|
||
#define UART_GET_FORCE_XOFF(i) GET_PERI_REG_BITS2(UART_FLOW_CONF_REG(i) , UART_FORCE_XOFF_V, UART_FORCE_XOFF_S)
|
||
#define UART_SET_FORCE_XOFF(i,val) SET_PERI_REG_BITS(UART_FLOW_CONF_REG(i) ,UART_FORCE_XOFF_V,(val),UART_FORCE_XOFF_S)
|
||
#define UART_GET_FORCE_XON(i) GET_PERI_REG_BITS2(UART_FLOW_CONF_REG(i) , UART_FORCE_XON_V, UART_FORCE_XON_S)
|
||
#define UART_SET_FORCE_XON(i,val) SET_PERI_REG_BITS(UART_FLOW_CONF_REG(i) ,UART_FORCE_XON_V,(val),UART_FORCE_XON_S)
|
||
#define UART_GET_XONOFF_DEL(i) GET_PERI_REG_BITS2(UART_FLOW_CONF_REG(i) , UART_XONOFF_DEL_V, UART_XONOFF_DEL_S)
|
||
#define UART_SET_XONOFF_DEL(i,val) SET_PERI_REG_BITS(UART_FLOW_CONF_REG(i) ,UART_XONOFF_DEL_V,(val),UART_XONOFF_DEL_S)
|
||
#define UART_GET_SW_FLOW_CON_EN(i) GET_PERI_REG_BITS2(UART_FLOW_CONF_REG(i) , UART_SW_FLOW_CON_EN_V, UART_SW_FLOW_CON_EN_S)
|
||
#define UART_SET_SW_FLOW_CON_EN(i,val) SET_PERI_REG_BITS(UART_FLOW_CONF_REG(i) ,UART_SW_FLOW_CON_EN_V,(val),UART_SW_FLOW_CON_EN_S)
|
||
|
||
|
||
|
||
#define UART_SLEEP_CONF_REG(i) (REG_UART_BASE(i) + 0x38)
|
||
/* UART_ACTIVE_THRESHOLD : R/W ;bitpos:[9:0] ;default: 10'hf0 ; */
|
||
/*description: when the num of rx level change is more than this value*/
|
||
#define UART_ACTIVE_THRESHOLD 0x000003FF
|
||
#define UART_ACTIVE_THRESHOLD_M ((UART_ACTIVE_THRESHOLD_V)<<(UART_ACTIVE_THRESHOLD_S))
|
||
#define UART_ACTIVE_THRESHOLD_V 0x3FF
|
||
#define UART_ACTIVE_THRESHOLD_S 0
|
||
#define UART_GET_ACTIVE_THRESHOLD(i) GET_PERI_REG_BITS2(UART_SLEEP_CONF_REG(i) , UART_ACTIVE_THRESHOLD_V, UART_ACTIVE_THRESHOLD_S)
|
||
#define UART_SET_ACTIVE_THRESHOLD(i,val) SET_PERI_REG_BITS(UART_SLEEP_CONF_REG(i) ,UART_ACTIVE_THRESHOLD_V,(val),UART_ACTIVE_THRESHOLD_S)
|
||
|
||
|
||
|
||
#define UART_SWFC_CONF_REG(i) (REG_UART_BASE(i) + 0x3C)
|
||
/* UART_XOFF_CHAR : R/W ;bitpos:[31:24] ;default: 8'h13 ; */
|
||
/*description: xoff char*/
|
||
#define UART_XOFF_CHAR 0x000000FF
|
||
#define UART_XOFF_CHAR_M ((UART_XOFF_CHAR_V)<<(UART_XOFF_CHAR_S))
|
||
#define UART_XOFF_CHAR_V 0xFF
|
||
#define UART_XOFF_CHAR_S 24
|
||
/* UART_XON_CHAR : R/W ;bitpos:[23:16] ;default: 8'h11 ; */
|
||
/*description: xon char*/
|
||
#define UART_XON_CHAR 0x000000FF
|
||
#define UART_XON_CHAR_M ((UART_XON_CHAR_V)<<(UART_XON_CHAR_S))
|
||
#define UART_XON_CHAR_V 0xFF
|
||
#define UART_XON_CHAR_S 16
|
||
/* UART_XOFF_THRESHOLD : R/W ;bitpos:[15:8] ;default: 8'he0 ; */
|
||
/*description: rx stop receiving data when rxfifo_cnt is more than this value*/
|
||
#define UART_XOFF_THRESHOLD 0x000000FF
|
||
#define UART_XOFF_THRESHOLD_M ((UART_XOFF_THRESHOLD_V)<<(UART_XOFF_THRESHOLD_S))
|
||
#define UART_XOFF_THRESHOLD_V 0xFF
|
||
#define UART_XOFF_THRESHOLD_S 8
|
||
/* UART_XON_THRESHOLD : R/W ;bitpos:[7:0] ;default: 8'h0 ; */
|
||
/*description: rx continue receiving data when rxfifo cnt is less then this value*/
|
||
#define UART_XON_THRESHOLD 0x000000FF
|
||
#define UART_XON_THRESHOLD_M ((UART_XON_THRESHOLD_V)<<(UART_XON_THRESHOLD_S))
|
||
#define UART_XON_THRESHOLD_V 0xFF
|
||
#define UART_XON_THRESHOLD_S 0
|
||
#define UART_GET_XOFF_CH(i) GET_PERI_REG_BITS2(UART_SWFC_CONF_REG(i) , UART_XOFF_CHAR_V, UART_XOFF_CHAR_S)
|
||
#define UART_SET_XOFF_CH(i,val) SET_PERI_REG_BITS(UART_SWFC_CONF_REG(i) ,UART_XOFF_CHAR_V,(val),UART_XOFF_CHAR_S)
|
||
#define UART_GET_XON_CH(i) GET_PERI_REG_BITS2(UART_SWFC_CONF_REG(i) , UART_XON_CHAR_V, UART_XON_CHAR_S)
|
||
#define UART_SET_XON_CH(i,val) SET_PERI_REG_BITS(UART_SWFC_CONF_REG(i) ,UART_XON_CHAR_V,(val),UART_XON_CHAR_S)
|
||
#define UART_GET_XOFF_THRESHOLD(i) GET_PERI_REG_BITS2(UART_SWFC_CONF_REG(i) , UART_XOFF_THRESHOLD_V, UART_XOFF_THRESHOLD_S)
|
||
#define UART_SET_XOFF_THRESHOLD(i,val) SET_PERI_REG_BITS(UART_SWFC_CONF_REG(i) ,UART_XOFF_THRESHOLD_V,(val),UART_XOFF_THRESHOLD_S)
|
||
#define UART_GET_XON_THRESHOLD(i) GET_PERI_REG_BITS2(UART_SWFC_CONF_REG(i) , UART_XON_THRESHOLD_V, UART_XON_THRESHOLD_S)
|
||
#define UART_SET_XON_THRESHOLD(i,val) SET_PERI_REG_BITS(UART_SWFC_CONF_REG(i) ,UART_XON_THRESHOLD_V,(val),UART_XON_THRESHOLD_S)
|
||
|
||
|
||
|
||
#define UART_IDLE_CONF_REG(i) (REG_UART_BASE(i) + 0x40)
|
||
/* UART_TX_BRK_NUM : R/W ;bitpos:[27:20] ;default: 8'ha ; */
|
||
/*description: brk number config*/
|
||
#define UART_TX_BRK_NUM 0x000000FF
|
||
#define UART_TX_BRK_NUM_M ((UART_TX_BRK_NUM_V)<<(UART_TX_BRK_NUM_S))
|
||
#define UART_TX_BRK_NUM_V 0xFF
|
||
#define UART_TX_BRK_NUM_S 20
|
||
/* UART_TX_IDLE_NUM : R/W ;bitpos:[19:10] ;default: 10'h100 ; */
|
||
/*description: idle number config*/
|
||
#define UART_TX_IDLE_NUM 0x000003FF
|
||
#define UART_TX_IDLE_NUM_M ((UART_TX_IDLE_NUM_V)<<(UART_TX_IDLE_NUM_S))
|
||
#define UART_TX_IDLE_NUM_V 0x3FF
|
||
#define UART_TX_IDLE_NUM_S 10
|
||
/* UART_RX_IDLE_THRHD : R/W ;bitpos:[9:0] ;default: 10'h100 ; */
|
||
/*description: rx idle number config*/
|
||
#define UART_RX_IDLE_THRHD 0x000003FF
|
||
#define UART_RX_IDLE_THRHD_M ((UART_RX_IDLE_THRHD_V)<<(UART_RX_IDLE_THRHD_S))
|
||
#define UART_RX_IDLE_THRHD_V 0x3FF
|
||
#define UART_RX_IDLE_THRHD_S 0
|
||
#define UART_GET_TX_BRK_NUM(i) GET_PERI_REG_BITS2(UART_IDLE_CONF_REG(i) , UART_TX_BRK_NUM_V, UART_TX_BRK_NUM_S)
|
||
#define UART_SET_TX_BRK_NUM(i,val) SET_PERI_REG_BITS(UART_IDLE_CONF_REG(i) ,UART_TX_BRK_NUM_V,(val),UART_TX_BRK_NUM_S)
|
||
#define UART_GET_TX_IDLE_NUM(i) GET_PERI_REG_BITS2(UART_IDLE_CONF_REG(i) , UART_TX_IDLE_NUM_V, UART_TX_IDLE_NUM_S)
|
||
#define UART_SET_TX_IDLE_NUM(i,val) SET_PERI_REG_BITS(UART_IDLE_CONF_REG(i) ,UART_TX_IDLE_NUM_V,(val),UART_TX_IDLE_NUM_S)
|
||
#define UART_GET_RX_IDLE_THRHD(i) GET_PERI_REG_BITS2(UART_IDLE_CONF_REG(i) , UART_RX_IDLE_THRHD_V, UART_RX_IDLE_THRHD_S)
|
||
#define UART_SET_RX_IDLE_THRHD(i,val) SET_PERI_REG_BITS(UART_IDLE_CONF_REG(i) ,UART_RX_IDLE_THRHD_V,(val),UART_RX_IDLE_THRHD_S)
|
||
|
||
|
||
|
||
#define UART_RS485_CONF_REG(i) (REG_UART_BASE(i) + 0x44)
|
||
/* UART_RS485_TX_DLY_NUM : R/W ;bitpos:[9:6] ;default: 4'b0 ; */
|
||
/*description: config this reg to delay tx signal*/
|
||
#define UART_RS485_TX_DLY_NUM 0x0000000F
|
||
#define UART_RS485_TX_DLY_NUM_M ((UART_RS485_TX_DLY_NUM_V)<<(UART_RS485_TX_DLY_NUM_S))
|
||
#define UART_RS485_TX_DLY_NUM_V 0xF
|
||
#define UART_RS485_TX_DLY_NUM_S 6
|
||
/* UART_RS485_RX_DLY_NUM : R/W ;bitpos:[5] ;default: 1'b0 ; */
|
||
/*description: config this reg to delay rx signal*/
|
||
#define UART_RS485_RX_DLY_NUM (BIT(5))
|
||
#define UART_RS485_RX_DLY_NUM_M (BIT(5))
|
||
#define UART_RS485_RX_DLY_NUM_V 0x1
|
||
#define UART_RS485_RX_DLY_NUM_S 5
|
||
/* UART_RS485RXBY_TX_EN : R/W ;bitpos:[4] ;default: 1'b0 ; */
|
||
/*description: set this bit to enable tx when rx is busy*/
|
||
#define UART_RS485RXBY_TX_EN (BIT(4))
|
||
#define UART_RS485RXBY_TX_EN_M (BIT(4))
|
||
#define UART_RS485RXBY_TX_EN_V 0x1
|
||
#define UART_RS485RXBY_TX_EN_S 4
|
||
/* UART_RS485TX_RX_EN : R/W ;bitpos:[3] ;default: 1'b0 ; */
|
||
/*description: set this bit to enable rx receiving when tx is sending*/
|
||
#define UART_RS485TX_RX_EN (BIT(3))
|
||
#define UART_RS485TX_RX_EN_M (BIT(3))
|
||
#define UART_RS485TX_RX_EN_V 0x1
|
||
#define UART_RS485TX_RX_EN_S 3
|
||
/* UART_DL1_EN : R/W ;bitpos:[2] ;default: 1'b0 ; */
|
||
/*description: set this bit to add 1 bit stop bit(after data)*/
|
||
#define UART_DL1_EN (BIT(2))
|
||
#define UART_DL1_EN_M (BIT(2))
|
||
#define UART_DL1_EN_V 0x1
|
||
#define UART_DL1_EN_S 2
|
||
/* UART_DL0_EN : R/W ;bitpos:[1] ;default: 1'b0 ; */
|
||
/*description: set this bit to add 1 bit stop bit(before data)*/
|
||
#define UART_DL0_EN (BIT(1))
|
||
#define UART_DL0_EN_M (BIT(1))
|
||
#define UART_DL0_EN_V 0x1
|
||
#define UART_DL0_EN_S 1
|
||
/* UART_RS485_EN : R/W ;bitpos:[0] ;default: 1'b0 ; */
|
||
/*description: set this bit to enable rs485 protocol*/
|
||
#define UART_RS485_EN (BIT(0))
|
||
#define UART_RS485_EN_M (BIT(0))
|
||
#define UART_RS485_EN_V 0x1
|
||
#define UART_RS485_EN_S 0
|
||
#define UART_GET_RS485_TX_DLY_NUM(i) GET_PERI_REG_BITS2(UART_RS485_CONF_REG(i) , UART_RS485_TX_DLY_NUM_V, UART_RS485_TX_DLY_NUM_S)
|
||
#define UART_SET_RS485_TX_DLY_NUM(i,val) SET_PERI_REG_BITS(UART_RS485_CONF_REG(i) ,UART_RS485_TX_DLY_NUM_V,(val),UART_RS485_TX_DLY_NUM_S)
|
||
#define UART_GET_RS485_RX_DLY_NUM(i) GET_PERI_REG_BITS2(UART_RS485_CONF_REG(i) , UART_RS485_RX_DLY_NUM_V, UART_RS485_RX_DLY_NUM_S)
|
||
#define UART_SET_RS485_RX_DLY_NUM(i,val) SET_PERI_REG_BITS(UART_RS485_CONF_REG(i) ,UART_RS485_RX_DLY_NUM_V,(val),UART_RS485_RX_DLY_NUM_S)
|
||
#define UART_GET_RS485RXBY_TX_EN(i) GET_PERI_REG_BITS2(UART_RS485_CONF_REG(i) , UART_RS485RXBY_TX_EN_V, UART_RS485RXBY_TX_EN_S)
|
||
#define UART_SET_RS485RXBY_TX_EN(i,val) SET_PERI_REG_BITS(UART_RS485_CONF_REG(i) ,UART_RS485RXBY_TX_EN_V,(val),UART_RS485RXBY_TX_EN_S)
|
||
#define UART_GET_RS485TX_RX_EN(i) GET_PERI_REG_BITS2(UART_RS485_CONF_REG(i) , UART_RS485TX_RX_EN_V, UART_RS485TX_RX_EN_S)
|
||
#define UART_SET_RS485TX_RX_EN(i,val) SET_PERI_REG_BITS(UART_RS485_CONF_REG(i) ,UART_RS485TX_RX_EN_V,(val),UART_RS485TX_RX_EN_S)
|
||
#define UART_GET_DL1_EN(i) GET_PERI_REG_BITS2(UART_RS485_CONF_REG(i) , UART_DL1_EN_V, UART_DL1_EN_S)
|
||
#define UART_SET_DL1_EN(i,val) SET_PERI_REG_BITS(UART_RS485_CONF_REG(i) ,UART_DL1_EN_V,(val),UART_DL1_EN_S)
|
||
#define UART_GET_DL0_EN(i) GET_PERI_REG_BITS2(UART_RS485_CONF_REG(i) , UART_DL0_EN_V, UART_DL0_EN_S)
|
||
#define UART_SET_DL0_EN(i,val) SET_PERI_REG_BITS(UART_RS485_CONF_REG(i) ,UART_DL0_EN_V,(val),UART_DL0_EN_S)
|
||
#define UART_GET_RS485_EN(i) GET_PERI_REG_BITS2(UART_RS485_CONF_REG(i) , UART_RS485_EN_V, UART_RS485_EN_S)
|
||
#define UART_SET_RS485_EN(i,val) SET_PERI_REG_BITS(UART_RS485_CONF_REG(i) ,UART_RS485_EN_V,(val),UART_RS485_EN_S)
|
||
|
||
|
||
|
||
#define UART_AT_CMD_PRECNT_REG(i) (REG_UART_BASE(i) + 0x48)
|
||
/* UART_PRE_IDLE_NUM : R/W ;bitpos:[23:0] ;default: 24'h186a00 ; */
|
||
/*description: config the idle time before receiving AT_CMD*/
|
||
#define UART_PRE_IDLE_NUM 0x00FFFFFF
|
||
#define UART_PRE_IDLE_NUM_M ((UART_PRE_IDLE_NUM_V)<<(UART_PRE_IDLE_NUM_S))
|
||
#define UART_PRE_IDLE_NUM_V 0xFFFFFF
|
||
#define UART_PRE_IDLE_NUM_S 0
|
||
#define UART_GET_PRE_IDLE_NUM(i) GET_PERI_REG_BITS2(UART_AT_CMD_PRECNT_REG(i) , UART_PRE_IDLE_NUM_V, UART_PRE_IDLE_NUM_S)
|
||
#define UART_SET_PRE_IDLE_NUM(i,val) SET_PERI_REG_BITS(UART_AT_CMD_PRECNT_REG(i) ,UART_PRE_IDLE_NUM_V,(val),UART_PRE_IDLE_NUM_S)
|
||
|
||
|
||
|
||
#define UART_AT_CMD_POSTCNT_REG(i) (REG_UART_BASE(i) + 0x4c)
|
||
/* UART_POST_IDLE_NUM : R/W ;bitpos:[23:0] ;default: 24'h186a00 ; */
|
||
/*description: config the idle time after receiving AT_CMD*/
|
||
#define UART_POST_IDLE_NUM 0x00FFFFFF
|
||
#define UART_POST_IDLE_NUM_M ((UART_POST_IDLE_NUM_V)<<(UART_POST_IDLE_NUM_S))
|
||
#define UART_POST_IDLE_NUM_V 0xFFFFFF
|
||
#define UART_POST_IDLE_NUM_S 0
|
||
#define UART_GET_POST_IDLE_NUM(i) GET_PERI_REG_BITS2(UART_AT_CMD_POSTCNT_REG(i) , UART_POST_IDLE_NUM_V, UART_POST_IDLE_NUM_S)
|
||
#define UART_SET_POST_IDLE_NUM(i,val) SET_PERI_REG_BITS(UART_AT_CMD_POSTCNT_REG(i) ,UART_POST_IDLE_NUM_V,(val),UART_POST_IDLE_NUM_S)
|
||
|
||
|
||
|
||
#define UART_AT_CMD_GAPTOUT_REG(i) (REG_UART_BASE(i) + 0x50)
|
||
/* UART_RX_GAP_TOUT : R/W ;bitpos:[23:0] ;default: 24'h1e00 ; */
|
||
/*description: config the time between receiving two AT_CMD*/
|
||
#define UART_RX_GAP_TOUT 0x00FFFFFF
|
||
#define UART_RX_GAP_TOUT_M ((UART_RX_GAP_TOUT_V)<<(UART_RX_GAP_TOUT_S))
|
||
#define UART_RX_GAP_TOUT_V 0xFFFFFF
|
||
#define UART_RX_GAP_TOUT_S 0
|
||
#define UART_GET_RX_GAP_TOUT(i) GET_PERI_REG_BITS2(UART_AT_CMD_GAPTOUT_REG(i) , UART_RX_GAP_TOUT_V, UART_RX_GAP_TOUT_S)
|
||
#define UART_SET_RX_GAP_TOUT(i,val) SET_PERI_REG_BITS(UART_AT_CMD_GAPTOUT_REG(i) ,UART_RX_GAP_TOUT_V,(val),UART_RX_GAP_TOUT_S)
|
||
|
||
|
||
|
||
#define UART_AT_CMD_CHAR_REG(i) (REG_UART_BASE(i) + 0x54)
|
||
/* UART_CHAR_NUM : R/W ;bitpos:[15:8] ;default: 8'd3 ; */
|
||
/*description: config the continous num of AT_CMD*/
|
||
#define UART_CHAR_NUM 0x000000FF
|
||
#define UART_CHAR_NUM_M ((UART_CHAR_NUM_V)<<(UART_CHAR_NUM_S))
|
||
#define UART_CHAR_NUM_V 0xFF
|
||
#define UART_CHAR_NUM_S 8
|
||
/* UART_AT_CMD_CHAR : R/W ;bitpos:[7:0] ;default: 8'h2b ; */
|
||
/*description: config AT_CMD*/
|
||
#define UART_AT_CMD_CHAR 0x000000FF
|
||
#define UART_AT_CMD_CHAR_M ((UART_AT_CMD_CHAR_V)<<(UART_AT_CMD_CHAR_S))
|
||
#define UART_AT_CMD_CHAR_V 0xFF
|
||
#define UART_AT_CMD_CHAR_S 0
|
||
#define UART_GET_CHAR_NUM(i) GET_PERI_REG_BITS2(UART_AT_CMD_CHAR_REG(i) , UART_CHAR_NUM_V, UART_CHAR_NUM_S)
|
||
#define UART_SET_CHAR_NUM(i,val) SET_PERI_REG_BITS(UART_AT_CMD_CHAR_REG(i) ,UART_CHAR_NUM_V,(val),UART_CHAR_NUM_S)
|
||
#define UART_GET_AT_CMD_CHAR(i) GET_PERI_REG_BITS2(UART_AT_CMD_CHAR_REG(i) , UART_AT_CMD_CHAR_V, UART_AT_CMD_CHAR_S)
|
||
#define UART_SET_AT_CMD_CHAR(i,val) SET_PERI_REG_BITS(UART_AT_CMD_CHAR_REG(i) ,UART_AT_CMD_CHAR_V,(val),UART_AT_CMD_CHAR_S)
|
||
|
||
|
||
|
||
#define UART_MEM_CONF_REG(i) (REG_UART_BASE(i) + 0x58)
|
||
/* UART_TX_MEM_EMPTY_THRHD : R/W ;bitpos:[30:28] ;default: 3'h0 ; */
|
||
/*description: the most significant bits of tx fifo empty threashold*/
|
||
#define UART_TX_MEM_EMPTY_THRHD 0x00000007
|
||
#define UART_TX_MEM_EMPTY_THRHD_M ((UART_TX_MEM_EMPTY_THRHD_V)<<(UART_TX_MEM_EMPTY_THRHD_S))
|
||
#define UART_TX_MEM_EMPTY_THRHD_V 0x7
|
||
#define UART_TX_MEM_EMPTY_THRHD_S 28
|
||
/* UART_RX_MEM_FULL_THRHD : R/W ;bitpos:[27:25] ;default: 3'h0 ; */
|
||
/*description: the most significant bits of rx fifo full threashold*/
|
||
#define UART_RX_MEM_FULL_THRHD 0x00000007
|
||
#define UART_RX_MEM_FULL_THRHD_M ((UART_RX_MEM_FULL_THRHD_V)<<(UART_RX_MEM_FULL_THRHD_S))
|
||
#define UART_RX_MEM_FULL_THRHD_V 0x7
|
||
#define UART_RX_MEM_FULL_THRHD_S 25
|
||
/* UART_XOFF_THRESHOLD_H2 : R/W ;bitpos:[24:23] ;default: 2'h0 ; */
|
||
/*description: the most significant bits of uart xoff flow threashold*/
|
||
#define UART_XOFF_THRESHOLD_H2 0x00000003
|
||
#define UART_XOFF_THRESHOLD_H2_M ((UART_XOFF_THRESHOLD_H2_V)<<(UART_XOFF_THRESHOLD_H2_S))
|
||
#define UART_XOFF_THRESHOLD_H2_V 0x3
|
||
#define UART_XOFF_THRESHOLD_H2_S 23
|
||
/* UART_XON_THRESHOLD_H2 : R/W ;bitpos:[22:21] ;default: 2'h0 ; */
|
||
/*description: the most significant bits of uart xon flow threshold*/
|
||
#define UART_XON_THRESHOLD_H2 0x00000003
|
||
#define UART_XON_THRESHOLD_H2_M ((UART_XON_THRESHOLD_H2_V)<<(UART_XON_THRESHOLD_H2_S))
|
||
#define UART_XON_THRESHOLD_H2_V 0x3
|
||
#define UART_XON_THRESHOLD_H2_S 21
|
||
/* UART_RX_TOUT_THRHD_H3 : R/W ;bitpos:[20:18] ;default: 3h0 ; */
|
||
/*description: the most significant bits of rx timeout threshold*/
|
||
#define UART_RX_TOUT_THRHD_H3 0x00000007
|
||
#define UART_RX_TOUT_THRHD_H3_M ((UART_RX_TOUT_THRHD_H3_V)<<(UART_RX_TOUT_THRHD_H3_S))
|
||
#define UART_RX_TOUT_THRHD_H3_V 0x7
|
||
#define UART_RX_TOUT_THRHD_H3_S 18
|
||
/* UART_RX_FLOW_THRHD_H3 : R/W ;bitpos:[17:15] ;default: 3'h0 ; */
|
||
/*description: the most significant bits of rx flow control threshold*/
|
||
#define UART_RX_FLOW_THRHD_H3 0x00000007
|
||
#define UART_RX_FLOW_THRHD_H3_M ((UART_RX_FLOW_THRHD_H3_V)<<(UART_RX_FLOW_THRHD_H3_S))
|
||
#define UART_RX_FLOW_THRHD_H3_V 0x7
|
||
#define UART_RX_FLOW_THRHD_H3_S 15
|
||
/* UART_TX_SIZE : R/W ;bitpos:[10:7] ;default: 3'h0 ; */
|
||
/*description: config tx_mem's size(128*reg_rx_size)*/
|
||
#define UART_TX_SIZE 0x0000000F
|
||
#define UART_TX_SIZE_M ((UART_TX_SIZE_V)<<(UART_TX_SIZE_S))
|
||
#define UART_TX_SIZE_V 0xF
|
||
#define UART_TX_SIZE_S 7
|
||
/* UART_RX_SIZE : R/W ;bitpos:[6:3] ;default: 3'h0 ; */
|
||
/*description: config rx mem's size(128*reg_rx_size)*/
|
||
#define UART_RX_SIZE 0x0000000F
|
||
#define UART_RX_SIZE_M ((UART_RX_SIZE_V)<<(UART_RX_SIZE_S))
|
||
#define UART_RX_SIZE_V 0xF
|
||
#define UART_RX_SIZE_S 3
|
||
/* UART_MEM_PD : R/W ;bitpos:[0] ;default: 1'b0 ; */
|
||
/*description: set this bit to pull_down mem's pd signal*/
|
||
#define UART_MEM_PD (BIT(0))
|
||
#define UART_MEM_PD_M (BIT(0))
|
||
#define UART_MEM_PD_V 0x1
|
||
#define UART_MEM_PD_S 0
|
||
#define UART_GET_TX_MEM_EMPTY_THRHD(i) GET_PERI_REG_BITS2(UART_MEM_CONF_REG(i) , UART_TX_MEM_EMPTY_THRHD_V, UART_TX_MEM_EMPTY_THRHD_S)
|
||
#define UART_SET_TX_MEM_EMPTY_THRHD(i,val) SET_PERI_REG_BITS(UART_MEM_CONF_REG(i) ,UART_TX_MEM_EMPTY_THRHD_V,(val),UART_TX_MEM_EMPTY_THRHD_S)
|
||
#define UART_GET_RX_MEM_FULL_THRHD(i) GET_PERI_REG_BITS2(UART_MEM_CONF_REG(i) , UART_RX_MEM_FULL_THRHD_V, UART_RX_MEM_FULL_THRHD_S)
|
||
#define UART_SET_RX_MEM_FULL_THRHD(i,val) SET_PERI_REG_BITS(UART_MEM_CONF_REG(i) ,UART_RX_MEM_FULL_THRHD_V,(val),UART_RX_MEM_FULL_THRHD_S)
|
||
#define UART_GET_XOFF_THRESHOLD_H2(i) GET_PERI_REG_BITS2(UART_MEM_CONF_REG(i) , UART_XOFF_THRESHOLD_H2_V, UART_XOFF_THRESHOLD_H2_S)
|
||
#define UART_SET_XOFF_THRESHOLD_H2(i,val) SET_PERI_REG_BITS(UART_MEM_CONF_REG(i) ,UART_XOFF_THRESHOLD_H2_V,(val),UART_XOFF_THRESHOLD_H2_S)
|
||
#define UART_GET_XON_THRESHOLD_H2(i) GET_PERI_REG_BITS2(UART_MEM_CONF_REG(i) , UART_XON_THRESHOLD_H2_V, UART_XON_THRESHOLD_H2_S)
|
||
#define UART_SET_XON_THRESHOLD_H2(i,val) SET_PERI_REG_BITS(UART_MEM_CONF_REG(i) ,UART_XON_THRESHOLD_H2_V,(val),UART_XON_THRESHOLD_H2_S)
|
||
#define UART_GET_RX_TOUT_THRHD_H3(i) GET_PERI_REG_BITS2(UART_MEM_CONF_REG(i) , UART_RX_TOUT_THRHD_H3_V, UART_RX_TOUT_THRHD_H3_S)
|
||
#define UART_SET_RX_TOUT_THRHD_H3(i,val) SET_PERI_REG_BITS(UART_MEM_CONF_REG(i) ,UART_RX_TOUT_THRHD_H3_V,(val),UART_RX_TOUT_THRHD_H3_S)
|
||
#define UART_GET_RX_FLOW_THRHD_H3(i) GET_PERI_REG_BITS2(UART_MEM_CONF_REG(i) , UART_RX_FLOW_THRHD_H3_V, UART_RX_FLOW_THRHD_H3_S)
|
||
#define UART_SET_RX_FLOW_THRHD_H3(i,val) SET_PERI_REG_BITS(UART_MEM_CONF_REG(i) ,UART_RX_FLOW_THRHD_H3_V,(val),UART_RX_FLOW_THRHD_H3_S)
|
||
#define UART_GET_REG_TX_SIZE(i) GET_PERI_REG_BITS2(UART_MEM_CONF_REG(i) , UART_TX_SIZE_V, UART_TX_SIZE_S)
|
||
#define UART_SET_REG_TX_SIZE(i,val) SET_PERI_REG_BITS(UART_MEM_CONF_REG(i) ,UART_TX_SIZE_V,(val),UART_TX_SIZE_S)
|
||
#define UART_GET_REG_RX_SIZE(i) GET_PERI_REG_BITS2(UART_MEM_CONF_REG(i) , UART_RX_SIZE_V, UART_RX_SIZE_S)
|
||
#define UART_SET_REG_RX_SIZE(i,val) SET_PERI_REG_BITS(UART_MEM_CONF_REG(i) ,UART_RX_SIZE_V,(val),UART_RX_SIZE_S)
|
||
#define UART_GET_REG_MEM_PD(i) GET_PERI_REG_BITS2(UART_MEM_CONF_REG(i) , UART_MEM_PD_V, UART_MEM_PD_S)
|
||
#define UART_SET_REG_MEM_PD(i,val) SET_PERI_REG_BITS(UART_MEM_CONF_REG(i) ,UART_MEM_PD_V,(val),UART_MEM_PD_S)
|
||
|
||
|
||
|
||
#define UART_MEM_TX_STATUS_REG(i) (REG_UART_BASE(i) + 0x5c)
|
||
/* UART_TX_RADDR_CHX : RO ;bitpos:[23:13] ;default: 11'b0 ; */
|
||
/*description: uartx tx mem's read address*/
|
||
#define UART_TX_RADDR_CHX 0x000007FF
|
||
#define UART_TX_RADDR_CHX_M ((UART_TX_RADDR_CHX_V)<<(UART_TX_RADDR_CHX_S))
|
||
#define UART_TX_RADDR_CHX_V 0x7FF
|
||
#define UART_TX_RADDR_CHX_S 13
|
||
/* UART_APB_TX_WADDR_CHX : RO ;bitpos:[12:2] ;default: 11'b0 ; */
|
||
/*description: uartx tx mem's write address*/
|
||
#define UART_APB_TX_WADDR_CHX 0x000007FF
|
||
#define UART_APB_TX_WADDR_CHX_M ((UART_APB_TX_WADDR_CHX_V)<<(UART_APB_TX_WADDR_CHX_S))
|
||
#define UART_APB_TX_WADDR_CHX_V 0x7FF
|
||
#define UART_APB_TX_WADDR_CHX_S 2
|
||
#define UART_GET_TX_RADDR_CHX(i) GET_PERI_REG_BITS2(UART_MEM_TX_STATUS_REG(i) , UART_TX_RADDR_CHX_V, UART_TX_RADDR_CHX_S)
|
||
#define UART_GET_APB_TX_WADDR_CHX(i) GET_PERI_REG_BITS2(UART_MEM_TX_STATUS_REG(i) , UART_APB_TX_WADDR_CHX_V, UART_APB_TX_WADDR_CHX_S)
|
||
|
||
|
||
|
||
#define UART_MEM_RX_STATUS_REG(i) (REG_UART_BASE(i) + 0x60)
|
||
/* UART_RX_WADDR_CHX : RO ;bitpos:[23:13] ;default: 11'b0 ; */
|
||
/*description: uartx rx mem's write address*/
|
||
#define UART_RX_WADDR_CHX 0x000007FF
|
||
#define UART_RX_WADDR_CHX_M ((UART_RX_WADDR_CHX_V)<<(UART_RX_WADDR_CHX_S))
|
||
#define UART_RX_WADDR_CHX_V 0x7FF
|
||
#define UART_RX_WADDR_CHX_S 13
|
||
/* UART_APB_RX_RADDR_CHX : RO ;bitpos:[12:2] ;default: 11'b0 ; */
|
||
/*description: uartx rx mem's read address*/
|
||
#define UART_APB_RX_RADDR_CHX 0x000007FF
|
||
#define UART_APB_RX_RADDR_CHX_M ((UART_APB_RX_RADDR_CHX_V)<<(UART_APB_RX_RADDR_CHX_S))
|
||
#define UART_APB_RX_RADDR_CHX_V 0x7FF
|
||
#define UART_APB_RX_RADDR_CHX_S 2
|
||
#define UART_GET_RX_WADDR_CHX(i) GET_PERI_REG_BITS2(UART_MEM_RX_STATUS_REG(i) , UART_RX_WADDR_CHX_V, UART_RX_WADDR_CHX_S)
|
||
#define UART_GET_APB_RX_RADDR_CHX(i) GET_PERI_REG_BITS2(UART_MEM_RX_STATUS_REG(i) , UART_APB_RX_RADDR_CHX_V, UART_APB_RX_RADDR_CHX_S)
|
||
|
||
|
||
|
||
#define UART_DATE_REG(i) (REG_UART_BASE(i) + 0x78)
|
||
/* UART_DATE : R/W ;bitpos:[31:0] ;default: 32'h15122500 ; */
|
||
/*description: */
|
||
#define UART_DATE 0xFFFFFFFF
|
||
#define UART_DATE_M ((UART_DATE_V)<<(UART_DATE_S))
|
||
#define UART_DATE_V 0xFFFFFFFF
|
||
#define UART_DATE_S 0
|
||
#define UART_GET_DATE(i) GET_PERI_REG_BITS2(UART_DATE_REG(i) , UART_DATE_V, UART_DATE_S)
|
||
#define UART_SET_DATE(i,val) SET_PERI_REG_BITS(UART_DATE_REG(i) ,UART_DATE_V,(val),UART_DATE_S)
|
||
|
||
|
||
|
||
#define UART_ID_REG(i) (REG_UART_BASE(i) + 0x7C)
|
||
/* UART_ID : R/W ;bitpos:[31:0] ;default: 32'h0500 ; */
|
||
/*description: */
|
||
#define UART_ID 0xFFFFFFFF
|
||
#define UART_ID_M ((UART_ID_V)<<(UART_ID_S))
|
||
#define UART_ID_V 0xFFFFFFFF
|
||
#define UART_ID_S 0
|
||
#define UART_GET_ID(i) GET_PERI_REG_BITS2(UART_ID_REG(i) , UART_ID_V, UART_ID_S)
|
||
#define UART_SET_ID(i,val) SET_PERI_REG_BITS(UART_ID_REG(i) ,UART_ID_V,(val),UART_ID_S)
|
||
|
||
|
||
|
||
|
||
|
||
|
||
#endif /* _SOC_UART_REG_H_ */
|
||
|
||
|