1. fix issues on sending beacon caused by too much tx retries on other packets.
2. modify not to scan if rc exists when connect.
3. modify scan dwell time to default 120ms fo root.
Need to make the bootloader modular so that users can redefine its functional part.
- refactoring and moving functions to the bootloader_support component
- Changed function to `void` bootloader_utility_load_image(...);
TW19596
Current code for recovery after power-off do not clean-up partially
erased items for FULL pages. If the erasure was part of modification
operation, this gets luckily cleaned-up because of duplicate detection
logic. For erase-only operation, the problem still exists. This patch
adds the recovery for FULL pages also.
Closes TW<20284>
When erasing a variable length item with an incorrect CRC32, the span
value of the item can not be trusted, so the item will be erased with
span = 1. Subsequent entries represent the data of the variable
length item, and these will be treated as separate items. For each
entry CRC32 is checked, the check most likely fails (because the
entry contains arbitrary data, and not a proper NVS item), and the
entry is erased. Erase function assumed that every item should be
present in cache, but it is not the case for the entries which are
just parts of item’s payload. This change allows for the item to be
not found in the hashlist, if the CRC32 check fails.
Current page selection algorithm selects a page for compaction based on just erased counts
and gives up when it does not find any page with erased count greater than 0. This is
problematic since the current allocation procedure skips the active page if there is not
enough room for the item in that page leaving free chunks on the pages. This change modifies
the algorithm to consider both erased as well as free counts on the candidate pages.
Closes TW<20297>
Users needs functions to count the number of free and used entries.
1. `nvs_get_stats()` This function return structure of statistic about the uspace NVS.
(Struct: used_entries, free_entries, total_entries and namespace_count)
2. `nvs_get_used_entry_count()` The second function return amount of entries in the namespace (by handler)
3. Added unit tests.
Closes TW<12282>
1. fix a bug in initliazing map beacon interval.
2. fix not send MESH_EVENT_ROUTING_TABLE_REMOVE when MESH_NWK_CHILD_DISCONNECTED.
3. fix a bug in returning roots ie len.
- In SPI mode, the card will respond to the initial SDIO reset (done
using CMD52) with “invalid command” error. Handle this correctly.
- sdmmc_card_init had a hack where GO_IDLE_STATE (CMD0) command was
sent twice. Add explanation why this is done, and don’t expect
correct response from the card on first CMD0.
- improve logs printed at debug level by adding CMD index
- Add SDIO support at protocol layer (probing, data transfer, interrupts)
- Add SDIO interrupts support in SDMMC host
- Add test (communicate with ESP32 in SDIO download mode)
Existing code assumed that response timeout is not followed by CMD_DONE,
which was not true, in fact. Host datasheet states that CMD_DONE is sent
after an RTO.
All the commands which do not have a response must have their flags set
accordingly. Therefore the host will not send RTO interrupt if response
is not expected. It is a bug in the code logic if it happens otherwise.
SDMMC host suffers from an issue that it outputs data near the rising
edge of the card clock, which is the edge used by the card to sample
data. If sampling time constraint is not satisfied, card may read data
after the transition.
The phases of output/input data can, in fact, be adjusted. However this
adjustment happens in the clock generation block outside of the host.
So the maximum phase change which can be created this way is equal to
half of the host clock period. So if the host clock is set to the lowest
possible frequency (for the given card frequency), then the phase offset
(and hence the hold time) will be the highest. This change modifies the
logic used to determine clock dividers accordingly.
sdmmc host: set correct dout phase and print correct frequency
SET_BUS_WIDTH is not a data transfer command. Extensive search in the
host datasheet and SD card spec did not reveal the origin of this hack
or 'feature'. Further testing showed that removing this does not lead to
regressions.
Fixes exceptions LoadProhibited, when rmt tries read variable p_rmt on RX END which can be 0.
It happens after esp_reset() (OTA) and the rmt is not probably stopped by it.
In other words the routine rmt_driver_isr_default was called before second rx channel was registered.
scenario:
register tx channel
register rx channel
reboot
register tx channel
-> exception (because rx channel is accessed)
Merges https://github.com/espressif/esp-idf/pull/1671
- In some cases where the HTTP URL contains the port number
(http://hostname:334), the DNS querier fails to resolve the hostname.
- Hence we have to populate the port number ourselves.
- This can only be done based on whether we get an IPv4 or IPv6
address.
Purpose:
1. TLS calls can be too many, and require a user to know the expected behaviour. A simple TLS socket wrapper that can be used in any higher level protocol.
2. Uses OpenSSL compatibility layer, so applications using esp-tls can be built on the host, and it should just work on ESP
Strips leading ../ when generating object file paths, keeps these in sync with the source files
otherwise.
This prevents object files landing in other directories, including outside the build directory, if
the component_srcdirs start with ../
When splitting a memory block, check if the next block is free.
If it is, then just extend it upwards instead of creating a new block.
This fixes a bug where when shrinking existing allocations would result in irreversible free space fragmentation.
When testing on the host, test all the poisoning configurations.
