Fix SPI master transmit length
Tx/Rx length fix from https://github.com/espressif/esp-idf/pull/336
I also added an extra commit in to make use of a define instead of a literal, plus fix a (harmless) off-by-one condition.
See merge request !521
Deep sleep fixes
This change fixes extra 24 uA current consumption in deep sleep mode (https://esp32.com/viewtopic.php?f=2&t=1133).
Recent update to libphy/librtc caused another problem that WiFi related parts of RTC are no longer disabled by RTC sleep functions. This means that if WiFi is not disabled by the application before entering deep sleep, extra ~200uA of current would be consumed. This is fixed, and documentation for esp_deep_sleep and SNTP example are updated to mention that applications should take care of disabling WiFi and BT before going into the deep sleep mode.
See merge request !516
spi_flash: fix protection issues
This MR fixes the two spi_flash related issues:
- esp_intr_noniram_{disable,enable} not being protected by spi_flash_op_{lock,unlock} in single core mode. This caused a safety assert to be triggered in esp_intr_noniram_disable.
- spi_flash_unlock not being protected by spi_flash_guard_{start,end}. This caused a conflict between SPI0 and SPI1 controllers when accessing SPI flash, manifesting in cache data corruption and IllegalInstruction exceptions, for some flash chips.
See merge request !522
spi_flash_unlock was missing spi_flash_guard_start, which caused cache
to be enabled during unlock operation, causing hard-to-trace crashes
and cache data corruption.
MR !441 (7c155ab) has fixed issue with esp_intr_noniram_{disable,enable}
calls not being properly protected by spi_flash_op_{lock,unlock}.
Unit test was added, but the unit test environment tests only dual-core
config. Similar issue was present in the code path for the single-core
config, where esp_intr_noniram_{disable,enable} calls were unprotected.
This change fixes the protection issue and updates the unit test to
run properly in single core config as well.
The issue with running unit tests for single core config will be
addressed in a separate MR.
In case WiFi/BT stack has been enabled but wasn’t disabled, some RTC
bits may be left enabled, causing increased current consumption.
This change returns some of the bits back to their default values.
Bootloader enables SAR ADC in test mode to get some entropy for the RNG.
The bits which control the ADC test mux were not disabled, which caused
extra ~24uA current to be drawn from VRTC, increasing deep sleep current
consumption. This change disables relevant test mode bits in
bootloader_random_disable.
1. add new APIs bt controller enable/disab/deinit
2. make bt controller work need to call two APIs of esp_bt_controller_init and enable
3. modify phy init to make mac reset once
1. add a macro in menuconfig for users to choose whether store phy calibration data into NVS or not.
2. rename some disable phy and rf APIs so that existing code which calls old APIS will fail to compile.
1. Add disable PHY and RF when WiFi and BT are both disabled(including call sniffer disable API).
2. Do not init PHY and RF when cpu start. Init PHY and RF when call Wifi or BT start APIs(including sniffer enable API).
3. Add a temporary lib: librtc_clk.a and will delete it when CPU frequency switching function is done.
4. Add an function to get OS tick rate.
5. Do not put the whole pp.a in iram0, only put lmac.o, ieee80211_misc.o, ets_time.o and wdev.o in iram0.
This connection error caused by iPhone, it think that TX data length must large than 27 when slave support EXTEND_DATA_LENGTH. But this should be allow. Besides, the problem cannot be found on higher version of Iphone7, apple seemed to have fixed it.
Actually maybe other BLE device have the same problem.
Docs: Document flash encryption disable steps, clean up flash encryption & secure boot docs
Generate clean up of flash encryption & secure boot docs
Including steps for disabling flash encryption (for people who accidentally enable it).
See merge request !500
phy_init: don’t rewrite valid calibration data
In the default PHY init routine, calibration data is loaded from NVS.
Most of the time the incremental changes to calibration will be fairly
small, so we don’t need to rewrite the existing calibration data stored
in the NVS.
Possible enhancement to be done in the future: expose a function in PHY
library to tell how big was the change in calibration data. If the
change was significant, then calibration data stored in NVS should be
updated.
See merge request !487
freertos: fix protection issue in freertos queue event list
When functions in queue.c calls listLIST_IS_EMPTY() to check queue event list, the queue list is
protected by queue mutex, on the other hand, when xTaskIncrementTick() modify the queue list, the
queue list is protected by xTaskQueueMutex, this may cause xTaskRemoveFromEventList operate on
the empty queue list and cause problem.
This change works around the problem by reducing the window where the race condition can happen.
See merge request !465
Also add steps to disable flash encryption, as some people seem to
accidentally enable it.
Explicitly mark the flash encryption and secure boot as "READ DOCS
FIRST" in menuconfig.
esp32: update wifi lib for some fixes and optimizations
1. Reduce the default static rx buffer size from 25 to 10
2. Adjust ampdu interrupt size to 3, namely, raise 1 interrupt per 3-mpdu
3. Make a copy for all received packets, including AMSDU/AMPDU/MPDU
4. Fix softap mis-forward issue
5. Fix pp q full issue
6. Fix sniffer copy wrong content issue
See merge request !491
When functions in queue.c calls listLIST_IS_EMPTY() to check queue event list, the queue list is
protected by queue mutex, on the other hand, when xTaskIncrementTick() modify the queue list, the
queue list is protected by xTaskQueueMutex, this may cause xTaskRemoveFromEventList operate on
the empty queue list and cause problem. This commit is to fix this bug.
may cause
1. Reduce the default static rx buffer size from 25 to 10
2. Adjust ampdu interrupt size to 3, namely, raise 1 interrupt per 3-mpdu
3. Make a copy for all received packets, including AMSDU/AMPDU/MPDU
4. Fix softap mis-forward issue
5. Fix pp q full issue
6. Fix sniffer copy wrong content issue
Fix interrupting task on other CPU that has lower prio than current task on current CPU
Fix for a very subtle bug introduced somewhere in december. This bug would cause a cross-core interrupt to only be sent if the activated task has a higher priority than the task currently running on *this* cpu, instead of on the other CPU.
See merge request !475
In the default PHY init routine, calibration data is loaded from NVS.
Most of the time the incremental changes to calibration will be fairly
small, so we don’t need to rewrite the existing calibration data stored
in the NVS.
Possible enhancement to be done in the future: expose a function in PHY
library to tell how big was the change in calibration data. If the
change was significant, then calibration data stored in NVS should be
updated.
