The IDF monitor waits for one second before printing the last
unterminated line. This is necessary for the correct filtering.
However, this causes poor performance, for example, in the case of the
system/console example.
This fix reduces the waiting time which improves the response time of
the console example and doesn't seem to influence the monitor filter.
Closes https://github.com/espressif/esp-idf/issues/2054
* a missing pointer increment caused error, if available was > 0 after the first iteration of while(available) loop.
* changed memory allocation strategy from large fixed size (RFCOMM_DATA_BUF_SIZE) to just the needed
size, which will be below MTU
Cherry-picked from https://github.com/espressif/esp-idf/pull/1923/
Since commit 94250e4, EXT0 wakeup mechanism, when wakeup level was set
to 0, started waking up chip immediately after entering deep sleep.
This failure was triggered in that commit by a change of
RTC_CNTL_MIN_SLP_VAL (i.e. minimum time in sleep mode until wakeup
can happen) from 128 cycles to 2 cycles.
The reason for this behaviour is related to the way input enable (IE)
signal going into an RTC pad is obtained:
PAD_IE = (SLP_SEL) ? SLP_IE & CHIP_SLEEP : IE,
where SLP_IE, SLP_SEL, and IE are bits of an RTC_IO register related
to the given pad. CHIP_SLEEP is the signal indicating that chip has
entered sleep mode.
The code in prepare_ext{0,1}_wakeup did not enable IE, but did enable
SLP_SEL and SLP_IE. This meant that until CHIP_SLEEP went high, PAD_IE
was 0, hence the input from the pad read 0 even if external signal
was 1. CHIP_SLEEP went high on the 2nd cycle of sleep. So when
RTC_CNTL_MIN_SLP_VAL was set to 2, the input signal from the pad was
latched as 0 at the moment when CHIP_SLEEP went high, causing EXT0
wakeup with level 0 to trigger.
This commit changes the way PAD_IE is enabled: SLP_SEL and SLP_IE are
no longer used, and IE is set to 1. If EXT0 wakeup is used, RTC_IO is
not powered down, so IE signal stays 1 both before CHIP_SLEEP goes
high and after. If EXT1 wakeup is used, RTC_IO may be powered down.
However prepare_ext1_wakeup enables Hold on the pad, locking states
of all the control signals, including IE.
Closes https://github.com/espressif/esp-idf/issues/1931
Closes https://github.com/espressif/esp-idf/issues/2043
For some test configurations, not all tests need to be run. This
change allows adding a comment in the configuration file of the
following form:
unit-test-app makefile will use it to determine which components to
build. If the comment is not present, all components will be built
(TESTS_ALL=1).
Also add test configuration for libsodium. It is a separate test
configuration due to the large binary size generated when building
libsodium tests.
Previously the loop in esp_timer_impl_set_alarm was necessary to catch
the case when timer count wraps around (goes from 2^32 - 1 to 0).
Since ALARM_OVERFLOW_VAL was reduced from 2^32 - 1 to 0xefffffff,
this is no longer necessary.
Fixes https://github.com/espressif/esp-idf/issues/1891
When ‘fetch’ strategy is used, Gitlab removes untracked files before
checking out new revision. However if the new revision doesn’t
include some of the submodules which were present in the old
revision, such submodule directories would not be removed by the
checkout. This extra step ensures that these stale submodules are
removed.
Allows you to move the partition table, it gives more space for the bootloader.
Added a new utility - parttool.py. This utility can search for the offset and/or size of the partitions by name and type/subtype. Use for getting APP_OFFSET and PHY_DATA_OFFSET.
The linker(esp32.bootloader.ld) made changes that allow you to write a custom bootloader code more.
TW14125
spi test: Prime the flash cache before each test to minimise flash cache misses.
VFS performance test: Increase the number of runs to minimise influence of an isolated bad run.
The old command caused was incorrect (x is “examine”, not “execute”)
and caused GDB register update only by chance. This replaces it with
“flushregs” command which purpose is exactly that — force GDB to
fetch registers from the remote.
