1. Change all the gattc API && bta gattc layer.
2. Debug the code and change the btc_ble_gattc_get_db method.
3. Change the gatt read API interface.
4. Reconstruction the BTA_gattc_cache code.
5. Change back the bluedroid_get_status to marco.
6. Change the gattc docs format.
7. Change the docs format.
8. fix the read char value bug.
9. change the gattc_get_attr_count method.
10. Change back the bta_gattc write ccc code.
11. Change the gattc api docs format
12. Change the gattc API docs.
13. Change the prepare write descriptor method to avoid the exection.
14. modify gatt clinet demo with new API
15. Change the p_src_data->read.p_value to avoid exection.
16. Change the bugfix of gattc unreg for the notify.
component/bt: Added the serch service res start_handle & end_handle to the result.
component/bt: Added the bta_gattc_cache_write when gatt discovery complete.
component/bt: Added the bta_gattc_cache_write declaration.
component/bt: Added the comments for esp_ble_gattc_cache_refresh API.
component/bt: Change the spelling errors & some comment error.
component/bt: fix bug of get gattc cache address list error.
1. Change the esp_bluedroid_get_status to macro;
2. added the malloc & free for the get_addr_list
component/bt: Added the addr_info->ass_addr == NULL Judgment to prevent crashes in the bta_gattc_co_cache_find_src_addr function.
component/bt: Fixed following gattc cache bugs
1. gattc can't refresh the gattc cache in the gatt discover state;
2. remove the nvs_get_blob in the cache address init function;
3. added the nvs_set_blob return value judgment in the cache address save function;
4. added the list_new when ass_address is NULL;
5. Change the ass_address list remove method to fix the ass address can't remove bug.
Current code for recovery after power-off do not clean-up partially
erased items for FULL pages. If the erasure was part of modification
operation, this gets luckily cleaned-up because of duplicate detection
logic. For erase-only operation, the problem still exists. This patch
adds the recovery for FULL pages also.
Closes TW<20284>
When erasing a variable length item with an incorrect CRC32, the span
value of the item can not be trusted, so the item will be erased with
span = 1. Subsequent entries represent the data of the variable
length item, and these will be treated as separate items. For each
entry CRC32 is checked, the check most likely fails (because the
entry contains arbitrary data, and not a proper NVS item), and the
entry is erased. Erase function assumed that every item should be
present in cache, but it is not the case for the entries which are
just parts of item’s payload. This change allows for the item to be
not found in the hashlist, if the CRC32 check fails.
Current page selection algorithm selects a page for compaction based on just erased counts
and gives up when it does not find any page with erased count greater than 0. This is
problematic since the current allocation procedure skips the active page if there is not
enough room for the item in that page leaving free chunks on the pages. This change modifies
the algorithm to consider both erased as well as free counts on the candidate pages.
Closes TW<20297>
Users needs functions to count the number of free and used entries.
1. `nvs_get_stats()` This function return structure of statistic about the uspace NVS.
(Struct: used_entries, free_entries, total_entries and namespace_count)
2. `nvs_get_used_entry_count()` The second function return amount of entries in the namespace (by handler)
3. Added unit tests.
Closes TW<12282>
1. fix a bug in initliazing map beacon interval.
2. fix not send MESH_EVENT_ROUTING_TABLE_REMOVE when MESH_NWK_CHILD_DISCONNECTED.
3. fix a bug in returning roots ie len.
- In SPI mode, the card will respond to the initial SDIO reset (done
using CMD52) with “invalid command” error. Handle this correctly.
- sdmmc_card_init had a hack where GO_IDLE_STATE (CMD0) command was
sent twice. Add explanation why this is done, and don’t expect
correct response from the card on first CMD0.
- improve logs printed at debug level by adding CMD index
- Add SDIO support at protocol layer (probing, data transfer, interrupts)
- Add SDIO interrupts support in SDMMC host
- Add test (communicate with ESP32 in SDIO download mode)
Existing code assumed that response timeout is not followed by CMD_DONE,
which was not true, in fact. Host datasheet states that CMD_DONE is sent
after an RTO.
All the commands which do not have a response must have their flags set
accordingly. Therefore the host will not send RTO interrupt if response
is not expected. It is a bug in the code logic if it happens otherwise.
SDMMC host suffers from an issue that it outputs data near the rising
edge of the card clock, which is the edge used by the card to sample
data. If sampling time constraint is not satisfied, card may read data
after the transition.
The phases of output/input data can, in fact, be adjusted. However this
adjustment happens in the clock generation block outside of the host.
So the maximum phase change which can be created this way is equal to
half of the host clock period. So if the host clock is set to the lowest
possible frequency (for the given card frequency), then the phase offset
(and hence the hold time) will be the highest. This change modifies the
logic used to determine clock dividers accordingly.
sdmmc host: set correct dout phase and print correct frequency
SET_BUS_WIDTH is not a data transfer command. Extensive search in the
host datasheet and SD card spec did not reveal the origin of this hack
or 'feature'. Further testing showed that removing this does not lead to
regressions.
