Previously when HashList was removing items, HashListBlocks were
removed lazily. This resulted in empty HashListBlocks dangling around
in full pages, even when all items have been erased. These blocks
would only be deleted when NVS was re-initialized
(nvs_flash_deinit/nvs_flash_init).
This change does eager cleanup instead, based on the code from
@negativekelvin offered in
https://github.com/espressif/esp-idf/issues/1642#issuecomment-367227994.
Closes https://github.com/espressif/esp-idf/issues/1642.
1. ref_clock used in unit tests occasionally produces time off by ~100
microseconds shortly after being started. Add a delay to let
ref_clock stabilise, until the cause is found.
2. Reduce roundoff error accumulation which would occasionally cause
the test to fail, by choosing an overflow value which can be divided
by APB frequency.
3. Move time sampling part of the test into an IRAM function to
reduce variations due to cache behavior.
4. Remove calculation of "standard deviation" in the test, as what was
calculated was not actually standard deviation, and it did not add any
useful information.
1. call esp_timer_get_time and ref_clock_get in the same order on
start and in the loop
2. disable interrupts when calculating delta between ref_clock
and esp_timer
3. ensure both functions are in cache before calculating the delta
In the situation when bootloader was compiled for 240MHz, and app was
compiled for 160MHz, and the chip is a revision 0 chip, the
bootloader will assume that the application has also been running at
240MHz. This will cause the chip to lock up later. Modify this to use
a run time check of DPORT_CPUPERIOD_SEL, which indicates which of the
PLL frequencies was used.
Closes https://github.com/espressif/esp-idf/issues/2731.
1. In original driver, the stack size for emac driver task "emacT" is only 2048 Bytes, which also can not be changed by user.
2. Each time when invoking "emac_start" function, it will reset emac registers, the driver should reconfig some important registers again.
Closes https://github.com/espressif/esp-idf/issues/3025
The bug will cause memory corrupted (the largest range is from 0x3ffc0000 ~ 0x3ffc8000),
some strange error will happen, like IllegalInstruction, LoadProhibited and .etc.
Fix following WiFi bugs:
1. Fix a crash bug which is caused by WiFi static TX buffer alloc/free.
2. Fix the bug that iphone fails to connect to ESP32 AP by enabling AP BAR receiving.
3. Fix the bug that ESP32 station fails to connect some APs, such as Xiaomi hotspot etc,
after reset.
This commit adds the ability for backtracing to trace from the itnerrupt to the
task stack, and across nested interrupts. Test cases have also been added.
See merge request !4084
Note: "Test backtrace from abort" reset reason modified by removing abort as a reason.
Shortcircuit evaluation may cause skip of _mdns_strdup_check of any further question field, which after clear_rx_packet freed undefined memory.
Fixes https://ezredmine.espressif.cn:8765/issues/28465
Originally, when doing BLE active scan, Bluedroid will not report adv to
application layer until receive scan response. This option is used to
disable the behavior. When enable this option, Bluedroid will report
adv data or scan response to application layer immediately.
Previously, hardware SHA engine "locks" were mutex semaphores. This meant that the task which
started a particular SHA session (in hardware) needed to finalise that session, or an invalid
FreeRTOS state was created.
Replace with binary semaphore which can be shared between tasks.
Includes a unit test, but unit test doesn't crash even without this fix
(some other unknown condition is required).
Bootloader used to calculate the number of cache pages assuming that
load address was aligned, while in reality load address for DROM and
IROM was offset by 0x20 bytes from the start of 64kB page. This
caused the bootloader to map one less page if the size of the image
was 0x4..0x1c less than a multiple of 64kB.
Reported in https://esp32.com/viewtopic.php?f=13&t=6952.