diff --git a/components/driver/include/driver/uart.h b/components/driver/include/driver/uart.h
index ed85e18a1..93c65c66f 100644
--- a/components/driver/include/driver/uart.h
+++ b/components/driver/include/driver/uart.h
@@ -792,6 +792,53 @@ esp_err_t uart_set_rx_timeout(uart_port_t uart_num, const uint8_t tout_thresh);
  */
 esp_err_t uart_get_collision_flag(uart_port_t uart_num, bool* collision_flag);
 
+/**
+ * @brief Set the number of RX pin signal edges for light sleep wakeup
+ *
+ * UART can be used to wake up the system from light sleep. This feature works
+ * by counting the number of positive edges on RX pin and comparing the count to
+ * the threshold. When the count exceeds the threshold, system is woken up from
+ * light sleep. This function allows setting the threshold value.
+ *
+ * Stop bit and parity bits (if enabled) also contribute to the number of edges.
+ * For example, letter 'a' with ASCII code 97 is encoded as 010001101 on the wire
+ * (with 8n1 configuration), start and stop bits included. This sequence has 3
+ * positive edges (transitions from 0 to 1). Therefore, to wake up the system
+ * when 'a' is sent, set wakeup_threshold=3.
+ *
+ * The character that triggers wakeup is not received by UART (i.e. it can not
+ * be obtained from UART FIFO). Depending on the baud rate, a few characters
+ * after that will also not be received. Note that when the chip enters and exits
+ * light sleep mode, APB frequency will be changing. To make sure that UART has
+ * correct baud rate all the time, select REF_TICK as UART clock source,
+ * by setting use_ref_tick field in uart_config_t to true.
+ *
+ * @note in ESP32, UART2 does not support light sleep wakeup feature.
+ *
+ * @param uart_num  UART number
+ * @param wakeup_threshold  number of RX edges for light sleep wakeup, value is 3 .. 0x3ff.
+ * @return
+ *      - ESP_OK on success
+ *      - ESP_ERR_INVALID_ARG if uart_num is incorrect or wakeup_threshold is
+ *        outside of [3, 0x3ff] range.
+ */
+esp_err_t uart_set_wakeup_threshold(uart_port_t uart_num, int wakeup_threshold);
+
+/**
+ * @brief Get the number of RX pin signal edges for light sleep wakeup.
+ *
+ * See description of uart_set_wakeup_threshold for the explanation of UART
+ * wakeup feature.
+ *
+ * @param uart_num  UART number
+ * @param[out] out_wakeup_threshold  output, set to the current value of wakeup
+ *                                   threshold for the given UART.
+ * @return
+ *      - ESP_OK on success
+ *      - ESP_ERR_INVALID_ARG if out_wakeup_threshold is NULL
+ */
+esp_err_t uart_get_wakeup_threshold(uart_port_t uart_num, int* out_wakeup_threshold);
+
 #ifdef __cplusplus
 }
 #endif
diff --git a/components/driver/uart.c b/components/driver/uart.c
index 876f4d027..0063007df 100644
--- a/components/driver/uart.c
+++ b/components/driver/uart.c
@@ -48,6 +48,7 @@ static const char* UART_TAG = "uart";
 #define UART_TOUT_REF_FACTOR_DEFAULT (UART_CLK_FREQ/(REF_CLK_FREQ<<UART_CLKDIV_FRAG_BIT_WIDTH))
 #define UART_TX_IDLE_NUM_DEFAULT   (0)
 #define UART_PATTERN_DET_QLEN_DEFAULT (10)
+#define UART_MIN_WAKEUP_THRESH      (2)
 
 #define UART_ENTER_CRITICAL_ISR(mux)    portENTER_CRITICAL_ISR(mux)
 #define UART_EXIT_CRITICAL_ISR(mux)     portEXIT_CRITICAL_ISR(mux)
@@ -1530,3 +1531,23 @@ esp_err_t uart_get_collision_flag(uart_port_t uart_num, bool* collision_flag)
     *collision_flag = p_uart_obj[uart_num]->coll_det_flg;
     return ESP_OK;
 }
+
+esp_err_t uart_set_wakeup_threshold(uart_port_t uart_num, int wakeup_threshold)
+{
+    UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_ERR_INVALID_ARG);
+    UART_CHECK((wakeup_threshold <= UART_ACTIVE_THRESHOLD_V &&
+                wakeup_threshold > UART_MIN_WAKEUP_THRESH),
+                "wakeup_threshold out of bounds", ESP_ERR_INVALID_ARG);
+
+    UART[uart_num]->sleep_conf.active_threshold = wakeup_threshold - UART_MIN_WAKEUP_THRESH;
+    return ESP_OK;
+}
+
+esp_err_t uart_get_wakeup_threshold(uart_port_t uart_num, int* out_wakeup_threshold)
+{
+    UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_ERR_INVALID_ARG);
+    UART_CHECK((out_wakeup_threshold != NULL), "argument is NULL", ESP_ERR_INVALID_ARG);
+
+    *out_wakeup_threshold = UART[uart_num]->sleep_conf.active_threshold + UART_MIN_WAKEUP_THRESH;
+    return ESP_OK;
+}