OVMS3-idf/components/driver/test/test_spi_master.c

1431 lines
54 KiB
C
Raw Normal View History

/*
Tests for the spi_master device driver
*/
#include <esp_types.h>
#include <stdio.h>
#include <stdlib.h>
#include <malloc.h>
#include <string.h>
#include "rom/ets_sys.h"
#include "freertos/FreeRTOS.h"
#include "freertos/task.h"
#include "freertos/semphr.h"
#include "freertos/queue.h"
#include "freertos/xtensa_api.h"
#include "unity.h"
#include "driver/spi_master.h"
#include "driver/spi_slave.h"
#include "soc/dport_reg.h"
#include "esp_heap_caps.h"
#include "esp_log.h"
#include "soc/spi_periph.h"
#include "freertos/ringbuf.h"
#include "soc/gpio_periph.h"
const static char TAG[] = "test_spi";
#define PIN_NUM_MISO HSPI_IOMUX_PIN_NUM_MISO
#define PIN_NUM_MOSI HSPI_IOMUX_PIN_NUM_MOSI
#define PIN_NUM_CLK HSPI_IOMUX_PIN_NUM_CLK
#define PIN_NUM_CS HSPI_IOMUX_PIN_NUM_CS
#define TEST_SPI_HOST HSPI_HOST
#define TEST_SLAVE_HOST VSPI_HOST
#define SPI_BUS_TEST_DEFAULT_CONFIG() {\
.miso_io_num=PIN_NUM_MISO, \
.mosi_io_num=PIN_NUM_MOSI,\
.sclk_io_num=PIN_NUM_CLK,\
.quadwp_io_num=-1,\
.quadhd_io_num=-1\
}
#define SPI_DEVICE_TEST_DEFAULT_CONFIG() {\
.clock_speed_hz=10*1000*1000,\
.mode=0,\
.spics_io_num=PIN_NUM_CS,\
.queue_size=16,\
.pre_cb=NULL, \
.cs_ena_pretrans = 0,\
.cs_ena_posttrans = 0,\
2018-04-19 04:47:29 +00:00
.input_delay_ns = 62.5,\
}
//default device config for slave devices
#define SPI_SLAVE_TEST_DEFAULT_CONFIG() {\
.mode=0,\
.spics_io_num=PIN_NUM_CS,\
.queue_size=3,\
.flags=0,\
}
#define FUNC_SPI 1
#define FUNC_GPIO 2
void gpio_output_sel(uint32_t gpio_num, int func, uint32_t signal_idx)
{
PIN_FUNC_SELECT(GPIO_PIN_MUX_REG[gpio_num], func);
GPIO.func_out_sel_cfg[gpio_num].func_sel=signal_idx;
}
static void check_spi_pre_n_for(int clk, int pre, int n)
{
esp_err_t ret;
spi_device_handle_t handle;
spi_device_interface_config_t devcfg={
.command_bits=0,
.address_bits=0,
.dummy_bits=0,
.clock_speed_hz=clk,
.duty_cycle_pos=128,
.mode=0,
.spics_io_num=21,
.queue_size=3
};
char sendbuf[16]="";
spi_transaction_t t;
memset(&t, 0, sizeof(t));
ret=spi_bus_add_device(HSPI_HOST, &devcfg, &handle);
TEST_ASSERT(ret==ESP_OK);
t.length=16*8;
t.tx_buffer=sendbuf;
ret=spi_device_transmit(handle, &t);
printf("Checking clk rate %dHz. expect pre %d n %d, got pre %d n %d\n", clk, pre, n, SPI2.clock.clkdiv_pre+1, SPI2.clock.clkcnt_n+1);
TEST_ASSERT(SPI2.clock.clkcnt_n+1==n);
TEST_ASSERT(SPI2.clock.clkdiv_pre+1==pre);
ret=spi_bus_remove_device(handle);
TEST_ASSERT(ret==ESP_OK);
}
TEST_CASE("SPI Master clockdiv calculation routines", "[spi]")
{
spi_bus_config_t buscfg={
.mosi_io_num=4,
.miso_io_num=26,
.sclk_io_num=25,
.quadwp_io_num=-1,
.quadhd_io_num=-1
};
esp_err_t ret;
ret=spi_bus_initialize(HSPI_HOST, &buscfg, 1);
TEST_ASSERT(ret==ESP_OK);
check_spi_pre_n_for(26000000, 1, 3);
check_spi_pre_n_for(20000000, 1, 4);
check_spi_pre_n_for(8000000, 1, 10);
check_spi_pre_n_for(800000, 2, 50);
check_spi_pre_n_for(100000, 16, 50);
check_spi_pre_n_for(333333, 4, 60);
2017-04-27 06:50:02 +00:00
check_spi_pre_n_for(900000, 2, 44);
check_spi_pre_n_for(1, 8192, 64); //Actually should generate the minimum clock speed, 152Hz
check_spi_pre_n_for(26000000, 1, 3);
ret=spi_bus_free(HSPI_HOST);
TEST_ASSERT(ret==ESP_OK);
}
static spi_device_handle_t setup_spi_bus(int clkspeed, bool dma) {
spi_bus_config_t buscfg={
.mosi_io_num=4,
.miso_io_num=26,
.sclk_io_num=25,
.quadwp_io_num=-1,
.quadhd_io_num=-1,
.max_transfer_sz=4096*3
};
spi_device_interface_config_t devcfg={
.command_bits=0,
.address_bits=0,
.dummy_bits=0,
.clock_speed_hz=clkspeed,
.duty_cycle_pos=128,
.mode=0,
.spics_io_num=21,
.queue_size=3,
};
esp_err_t ret;
spi_device_handle_t handle;
printf("THIS TEST NEEDS A JUMPER BETWEEN IO4 AND IO26\n");
ret=spi_bus_initialize(HSPI_HOST, &buscfg, dma?1:0);
TEST_ASSERT(ret==ESP_OK);
ret=spi_bus_add_device(HSPI_HOST, &devcfg, &handle);
TEST_ASSERT(ret==ESP_OK);
printf("Bus/dev inited.\n");
return handle;
}
static void spi_test(spi_device_handle_t handle, int num_bytes) {
esp_err_t ret;
int x;
srand(num_bytes);
char *sendbuf=heap_caps_malloc(num_bytes, MALLOC_CAP_DMA);
char *recvbuf=heap_caps_malloc(num_bytes, MALLOC_CAP_DMA);
for (x=0; x<num_bytes; x++) {
sendbuf[x]=rand()&0xff;
recvbuf[x]=0x55;
}
spi_transaction_t t;
memset(&t, 0, sizeof(t));
t.length=num_bytes*8;
t.tx_buffer=sendbuf;
t.rx_buffer=recvbuf;
t.addr=0xA00000000000000FL;
t.cmd=0x55;
printf("Transmitting %d bytes...\n", num_bytes);
ret=spi_device_transmit(handle, &t);
TEST_ASSERT(ret==ESP_OK);
srand(num_bytes);
for (x=0; x<num_bytes; x++) {
if (sendbuf[x]!=(rand()&0xff)) {
printf("Huh? Sendbuf corrupted at byte %d\n", x);
TEST_ASSERT(0);
}
if (sendbuf[x]!=recvbuf[x]) break;
}
if (x!=num_bytes) {
int from=x-16;
if (from<0) from=0;
printf("Error at %d! Sent vs recved: (starting from %d)\n" , x, from);
for (int i=0; i<32; i++) {
if (i+from<num_bytes) printf("%02X ", sendbuf[from+i]);
}
printf("\n");
for (int i=0; i<32; i++) {
if (i+from<num_bytes) printf("%02X ", recvbuf[from+i]);
}
printf("\n");
// TEST_ASSERT(0);
}
printf("Success!\n");
free(sendbuf);
free(recvbuf);
}
static void destroy_spi_bus(spi_device_handle_t handle) {
esp_err_t ret;
ret=spi_bus_remove_device(handle);
TEST_ASSERT(ret==ESP_OK);
ret=spi_bus_free(HSPI_HOST);
TEST_ASSERT(ret==ESP_OK);
}
#define TEST_LEN 111
TEST_CASE("SPI Master test", "[spi][ignore]")
{
printf("Testing bus at 80KHz\n");
spi_device_handle_t handle=setup_spi_bus(80000, true);
spi_test(handle, 16); //small
spi_test(handle, 21); //small, unaligned
spi_test(handle, 36); //aligned
spi_test(handle, 128); //aligned
spi_test(handle, 129); //unaligned
spi_test(handle, 4096-2); //multiple descs, edge case 1
spi_test(handle, 4096-1); //multiple descs, edge case 2
spi_test(handle, 4096*3); //multiple descs
destroy_spi_bus(handle);
printf("Testing bus at 80KHz, non-DMA\n");
handle=setup_spi_bus(80000, false);
spi_test(handle, 4); //aligned
spi_test(handle, 16); //small
spi_test(handle, 21); //small, unaligned
destroy_spi_bus(handle);
printf("Testing bus at 26MHz\n");
handle=setup_spi_bus(20000000, true);
spi_test(handle, 128); //DMA, aligned
spi_test(handle, 4096*3); //DMA, multiple descs
destroy_spi_bus(handle);
printf("Testing bus at 900KHz\n");
handle=setup_spi_bus(9000000, true);
spi_test(handle, 128); //DMA, aligned
spi_test(handle, 4096*3); //DMA, multiple descs
destroy_spi_bus(handle);
}
TEST_CASE("SPI Master test, interaction of multiple devs", "[spi][ignore]") {
esp_err_t ret;
spi_device_interface_config_t devcfg={
.command_bits=0,
.address_bits=0,
.dummy_bits=0,
.clock_speed_hz=1000000,
.duty_cycle_pos=128,
.mode=0,
.spics_io_num=23,
.queue_size=3,
};
spi_device_handle_t handle1=setup_spi_bus(80000, true);
spi_device_handle_t handle2;
spi_bus_add_device(HSPI_HOST, &devcfg, &handle2);
printf("Sending to dev 1\n");
spi_test(handle1, 7);
printf("Sending to dev 1\n");
spi_test(handle1, 15);
printf("Sending to dev 2\n");
spi_test(handle2, 15);
printf("Sending to dev 1\n");
spi_test(handle1, 32);
printf("Sending to dev 2\n");
spi_test(handle2, 32);
printf("Sending to dev 1\n");
spi_test(handle1, 63);
printf("Sending to dev 2\n");
spi_test(handle2, 63);
printf("Sending to dev 1\n");
spi_test(handle1, 5000);
printf("Sending to dev 2\n");
spi_test(handle2, 5000);
ret=spi_bus_remove_device(handle2);
2017-04-27 06:50:02 +00:00
TEST_ASSERT(ret==ESP_OK);
destroy_spi_bus(handle1);
}
static esp_err_t test_master_pins(int mosi, int miso, int sclk, int cs)
{
esp_err_t ret;
spi_bus_config_t cfg = SPI_BUS_TEST_DEFAULT_CONFIG();
cfg.mosi_io_num = mosi;
cfg.miso_io_num = miso;
cfg.sclk_io_num = sclk;
spi_device_interface_config_t master_cfg = SPI_DEVICE_TEST_DEFAULT_CONFIG();
master_cfg.spics_io_num = cs;
ret = spi_bus_initialize(TEST_SPI_HOST, &cfg, 1);
if (ret != ESP_OK) return ret;
spi_device_handle_t spi;
ret = spi_bus_add_device(TEST_SPI_HOST, &master_cfg, &spi);
if (ret != ESP_OK) {
spi_bus_free(TEST_SPI_HOST);
return ret;
}
TEST_ASSERT(spi_bus_remove_device(spi) == ESP_OK);
TEST_ASSERT(spi_bus_free(TEST_SPI_HOST) == ESP_OK);
return ESP_OK;
}
static esp_err_t test_slave_pins(int mosi, int miso, int sclk, int cs)
{
esp_err_t ret;
spi_bus_config_t cfg = SPI_BUS_TEST_DEFAULT_CONFIG();
cfg.mosi_io_num = mosi;
cfg.miso_io_num = miso;
cfg.sclk_io_num = sclk;
spi_slave_interface_config_t slave_cfg = SPI_SLAVE_TEST_DEFAULT_CONFIG();
slave_cfg.spics_io_num = cs;
ret = spi_slave_initialize(TEST_SLAVE_HOST, &cfg, &slave_cfg, 1);
if (ret != ESP_OK) return ret;
spi_slave_free(TEST_SLAVE_HOST);
return ESP_OK;
}
TEST_CASE("spi placed on input-only pins", "[spi]")
{
TEST_ESP_OK(test_master_pins(PIN_NUM_MOSI, PIN_NUM_MISO, PIN_NUM_CLK, PIN_NUM_CS));
TEST_ASSERT(test_master_pins(34, PIN_NUM_MISO, PIN_NUM_CLK, PIN_NUM_CS)!=ESP_OK);
TEST_ESP_OK(test_master_pins(PIN_NUM_MOSI, 34, PIN_NUM_CLK, PIN_NUM_CS));
TEST_ASSERT(test_master_pins(PIN_NUM_MOSI, PIN_NUM_MISO, 34, PIN_NUM_CS)!=ESP_OK);
TEST_ASSERT(test_master_pins(PIN_NUM_MOSI, PIN_NUM_MISO, PIN_NUM_CLK, 34)!=ESP_OK);
TEST_ESP_OK(test_slave_pins(PIN_NUM_MOSI, PIN_NUM_MISO, PIN_NUM_CLK, PIN_NUM_CS));
TEST_ESP_OK(test_slave_pins(34, PIN_NUM_MISO, PIN_NUM_CLK, PIN_NUM_CS));
TEST_ASSERT(test_slave_pins(PIN_NUM_MOSI, 34, PIN_NUM_CLK, PIN_NUM_CS)!=ESP_OK);
TEST_ESP_OK(test_slave_pins(PIN_NUM_MOSI, PIN_NUM_MISO, 34, PIN_NUM_CS));
TEST_ESP_OK(test_slave_pins(PIN_NUM_MOSI, PIN_NUM_MISO, PIN_NUM_CLK, 34));
}
TEST_CASE("spi bus setting with different pin configs", "[spi]")
{
spi_bus_config_t cfg;
uint32_t flags_o;
uint32_t flags_expected;
ESP_LOGI(TAG, "test 6 iomux output pins...");
flags_expected = SPICOMMON_BUSFLAG_SCLK | SPICOMMON_BUSFLAG_MOSI | SPICOMMON_BUSFLAG_MISO | SPICOMMON_BUSFLAG_NATIVE_PINS | SPICOMMON_BUSFLAG_QUAD;
cfg = (spi_bus_config_t){.mosi_io_num = HSPI_IOMUX_PIN_NUM_MOSI, .miso_io_num = HSPI_IOMUX_PIN_NUM_MISO, .sclk_io_num = HSPI_IOMUX_PIN_NUM_CLK, .quadhd_io_num = HSPI_IOMUX_PIN_NUM_HD, .quadwp_io_num = HSPI_IOMUX_PIN_NUM_WP,
.max_transfer_sz = 8, .flags = flags_expected};
TEST_ESP_OK(spicommon_bus_initialize_io(HSPI_HOST, &cfg, 0, flags_expected|SPICOMMON_BUSFLAG_MASTER, &flags_o));
TEST_ASSERT_EQUAL_HEX32( flags_expected, flags_o );
TEST_ESP_OK(spicommon_bus_initialize_io(HSPI_HOST, &cfg, 0, flags_expected|SPICOMMON_BUSFLAG_SLAVE, &flags_o));
TEST_ASSERT_EQUAL_HEX32( flags_expected, flags_o );
ESP_LOGI(TAG, "test 4 iomux output pins...");
flags_expected = SPICOMMON_BUSFLAG_SCLK | SPICOMMON_BUSFLAG_MOSI | SPICOMMON_BUSFLAG_MISO | SPICOMMON_BUSFLAG_NATIVE_PINS | SPICOMMON_BUSFLAG_DUAL;
cfg = (spi_bus_config_t){.mosi_io_num = HSPI_IOMUX_PIN_NUM_MOSI, .miso_io_num = HSPI_IOMUX_PIN_NUM_MISO, .sclk_io_num = HSPI_IOMUX_PIN_NUM_CLK, .quadhd_io_num = -1, .quadwp_io_num = -1,
.max_transfer_sz = 8, .flags = flags_expected};
TEST_ESP_OK(spicommon_bus_initialize_io(HSPI_HOST, &cfg, 0, flags_expected|SPICOMMON_BUSFLAG_MASTER, &flags_o));
TEST_ASSERT_EQUAL_HEX32( flags_expected, flags_o );
TEST_ESP_OK(spicommon_bus_initialize_io(HSPI_HOST, &cfg, 0, flags_expected|SPICOMMON_BUSFLAG_SLAVE, &flags_o));
TEST_ASSERT_EQUAL_HEX32( flags_expected, flags_o );
ESP_LOGI(TAG, "test 6 output pins...");
flags_expected = SPICOMMON_BUSFLAG_SCLK | SPICOMMON_BUSFLAG_MOSI | SPICOMMON_BUSFLAG_MISO | SPICOMMON_BUSFLAG_QUAD;
//swap MOSI and MISO
cfg = (spi_bus_config_t){.mosi_io_num = HSPI_IOMUX_PIN_NUM_MISO, .miso_io_num = HSPI_IOMUX_PIN_NUM_MOSI, .sclk_io_num = HSPI_IOMUX_PIN_NUM_CLK, .quadhd_io_num = HSPI_IOMUX_PIN_NUM_HD, .quadwp_io_num = HSPI_IOMUX_PIN_NUM_WP,
.max_transfer_sz = 8, .flags = flags_expected};
TEST_ESP_OK(spicommon_bus_initialize_io(HSPI_HOST, &cfg, 0, flags_expected|SPICOMMON_BUSFLAG_MASTER, &flags_o));
TEST_ASSERT_EQUAL_HEX32( flags_expected, flags_o );
TEST_ESP_OK(spicommon_bus_initialize_io(HSPI_HOST, &cfg, 0, flags_expected|SPICOMMON_BUSFLAG_SLAVE, &flags_o));
TEST_ASSERT_EQUAL_HEX32( flags_expected, flags_o );
ESP_LOGI(TAG, "test 4 output pins...");
flags_expected = SPICOMMON_BUSFLAG_SCLK | SPICOMMON_BUSFLAG_MOSI | SPICOMMON_BUSFLAG_MISO | SPICOMMON_BUSFLAG_DUAL;
//swap MOSI and MISO
cfg = (spi_bus_config_t){.mosi_io_num = HSPI_IOMUX_PIN_NUM_MISO, .miso_io_num = HSPI_IOMUX_PIN_NUM_MOSI, .sclk_io_num = HSPI_IOMUX_PIN_NUM_CLK, .quadhd_io_num = -1, .quadwp_io_num = -1,
.max_transfer_sz = 8, .flags = flags_expected};
TEST_ESP_OK(spicommon_bus_initialize_io(HSPI_HOST, &cfg, 0, flags_expected|SPICOMMON_BUSFLAG_MASTER, &flags_o));
TEST_ASSERT_EQUAL_HEX32( flags_expected, flags_o );
TEST_ESP_OK(spicommon_bus_initialize_io(HSPI_HOST, &cfg, 0, flags_expected|SPICOMMON_BUSFLAG_SLAVE, &flags_o));
TEST_ASSERT_EQUAL_HEX32( flags_expected, flags_o );
ESP_LOGI(TAG, "test master 5 output pins and MOSI on input-only pin...");
flags_expected = SPICOMMON_BUSFLAG_SCLK | SPICOMMON_BUSFLAG_MOSI | SPICOMMON_BUSFLAG_MISO | SPICOMMON_BUSFLAG_WPHD;
cfg = (spi_bus_config_t){.mosi_io_num = HSPI_IOMUX_PIN_NUM_MOSI, .miso_io_num = 34, .sclk_io_num = HSPI_IOMUX_PIN_NUM_CLK, .quadhd_io_num = HSPI_IOMUX_PIN_NUM_HD, .quadwp_io_num = HSPI_IOMUX_PIN_NUM_WP,
.max_transfer_sz = 8, .flags = flags_expected};
TEST_ESP_OK(spicommon_bus_initialize_io(HSPI_HOST, &cfg, 0, flags_expected|SPICOMMON_BUSFLAG_MASTER, &flags_o));
TEST_ASSERT_EQUAL_HEX32( flags_expected, flags_o );
ESP_LOGI(TAG, "test slave 5 output pins and MISO on input-only pin...");
flags_expected = SPICOMMON_BUSFLAG_SCLK | SPICOMMON_BUSFLAG_MOSI | SPICOMMON_BUSFLAG_MISO | SPICOMMON_BUSFLAG_WPHD;
cfg = (spi_bus_config_t){.mosi_io_num = 34, .miso_io_num = HSPI_IOMUX_PIN_NUM_MISO, .sclk_io_num = HSPI_IOMUX_PIN_NUM_CLK, .quadhd_io_num = HSPI_IOMUX_PIN_NUM_HD, .quadwp_io_num = HSPI_IOMUX_PIN_NUM_WP,
.max_transfer_sz = 8, .flags = flags_expected};
TEST_ESP_OK(spicommon_bus_initialize_io(HSPI_HOST, &cfg, 0, flags_expected|SPICOMMON_BUSFLAG_SLAVE, &flags_o));
TEST_ASSERT_EQUAL_HEX32( flags_expected, flags_o );
ESP_LOGI(TAG, "test master 3 output pins and MOSI on input-only pin...");
flags_expected = SPICOMMON_BUSFLAG_SCLK | SPICOMMON_BUSFLAG_MOSI | SPICOMMON_BUSFLAG_MISO;
cfg = (spi_bus_config_t){.mosi_io_num = HSPI_IOMUX_PIN_NUM_MOSI, .miso_io_num = 34, .sclk_io_num = HSPI_IOMUX_PIN_NUM_CLK, .quadhd_io_num = -1, .quadwp_io_num = -1,
.max_transfer_sz = 8, .flags = flags_expected};
TEST_ESP_OK(spicommon_bus_initialize_io(HSPI_HOST, &cfg, 0, flags_expected|SPICOMMON_BUSFLAG_MASTER, &flags_o));
TEST_ASSERT_EQUAL_HEX32( flags_expected, flags_o );
ESP_LOGI(TAG, "test slave 3 output pins and MISO on input-only pin...");
flags_expected = SPICOMMON_BUSFLAG_SCLK | SPICOMMON_BUSFLAG_MOSI | SPICOMMON_BUSFLAG_MISO;
cfg = (spi_bus_config_t){.mosi_io_num = 34, .miso_io_num = HSPI_IOMUX_PIN_NUM_MISO, .sclk_io_num = HSPI_IOMUX_PIN_NUM_CLK, .quadhd_io_num = -1, .quadwp_io_num = -1,
.max_transfer_sz = 8, .flags = flags_expected};
TEST_ESP_OK(spicommon_bus_initialize_io(HSPI_HOST, &cfg, 0, flags_expected|SPICOMMON_BUSFLAG_SLAVE, &flags_o));
TEST_ASSERT_EQUAL_HEX32( flags_expected, flags_o );
ESP_LOGI(TAG, "check native flag for 6 output pins...");
flags_expected = SPICOMMON_BUSFLAG_NATIVE_PINS;
//swap MOSI and MISO
cfg = (spi_bus_config_t){.mosi_io_num = HSPI_IOMUX_PIN_NUM_MISO, .miso_io_num = HSPI_IOMUX_PIN_NUM_MOSI, .sclk_io_num = HSPI_IOMUX_PIN_NUM_CLK, .quadhd_io_num = HSPI_IOMUX_PIN_NUM_HD, .quadwp_io_num = HSPI_IOMUX_PIN_NUM_WP,
.max_transfer_sz = 8, .flags = flags_expected};
TEST_ASSERT_EQUAL(ESP_ERR_INVALID_ARG, spicommon_bus_initialize_io(HSPI_HOST, &cfg, 0, flags_expected|SPICOMMON_BUSFLAG_MASTER, &flags_o));
TEST_ASSERT_EQUAL(ESP_ERR_INVALID_ARG, spicommon_bus_initialize_io(HSPI_HOST, &cfg, 0, flags_expected|SPICOMMON_BUSFLAG_SLAVE, &flags_o));
ESP_LOGI(TAG, "check native flag for 4 output pins...");
flags_expected = SPICOMMON_BUSFLAG_NATIVE_PINS;
//swap MOSI and MISO
cfg = (spi_bus_config_t){.mosi_io_num = HSPI_IOMUX_PIN_NUM_MISO, .miso_io_num = HSPI_IOMUX_PIN_NUM_MOSI, .sclk_io_num = HSPI_IOMUX_PIN_NUM_CLK, .quadhd_io_num = -1, .quadwp_io_num = -1,
.max_transfer_sz = 8, .flags = flags_expected};
TEST_ASSERT_EQUAL(ESP_ERR_INVALID_ARG, spicommon_bus_initialize_io(HSPI_HOST, &cfg, 0, flags_expected|SPICOMMON_BUSFLAG_MASTER, &flags_o));
TEST_ASSERT_EQUAL(ESP_ERR_INVALID_ARG, spicommon_bus_initialize_io(HSPI_HOST, &cfg, 0, flags_expected|SPICOMMON_BUSFLAG_SLAVE, &flags_o));
ESP_LOGI(TAG, "check dual flag for master 5 output pins and MISO/MOSI on input-only pin...");
flags_expected = SPICOMMON_BUSFLAG_DUAL;
cfg = (spi_bus_config_t){.mosi_io_num = HSPI_IOMUX_PIN_NUM_MOSI, .miso_io_num = 34, .sclk_io_num = HSPI_IOMUX_PIN_NUM_CLK, .quadhd_io_num = HSPI_IOMUX_PIN_NUM_HD, .quadwp_io_num = HSPI_IOMUX_PIN_NUM_WP,
.max_transfer_sz = 8, .flags = flags_expected};
TEST_ASSERT_EQUAL(ESP_ERR_INVALID_ARG, spicommon_bus_initialize_io(HSPI_HOST, &cfg, 0, flags_expected|SPICOMMON_BUSFLAG_MASTER, &flags_o));
TEST_ASSERT_EQUAL(ESP_ERR_INVALID_ARG, spicommon_bus_initialize_io(HSPI_HOST, &cfg, 0, flags_expected|SPICOMMON_BUSFLAG_SLAVE, &flags_o));
cfg = (spi_bus_config_t){.mosi_io_num = 34, .miso_io_num = HSPI_IOMUX_PIN_NUM_MISO, .sclk_io_num = HSPI_IOMUX_PIN_NUM_CLK, .quadhd_io_num = HSPI_IOMUX_PIN_NUM_HD, .quadwp_io_num = HSPI_IOMUX_PIN_NUM_WP,
.max_transfer_sz = 8, .flags = flags_expected};
TEST_ASSERT_EQUAL(ESP_ERR_INVALID_ARG, spicommon_bus_initialize_io(HSPI_HOST, &cfg, 0, flags_expected|SPICOMMON_BUSFLAG_MASTER, &flags_o));
TEST_ASSERT_EQUAL(ESP_ERR_INVALID_ARG, spicommon_bus_initialize_io(HSPI_HOST, &cfg, 0, flags_expected|SPICOMMON_BUSFLAG_SLAVE, &flags_o));
ESP_LOGI(TAG, "check dual flag for master 3 output pins and MISO/MOSI on input-only pin...");
flags_expected = SPICOMMON_BUSFLAG_DUAL;
cfg = (spi_bus_config_t){.mosi_io_num = HSPI_IOMUX_PIN_NUM_MOSI, .miso_io_num = 34, .sclk_io_num = HSPI_IOMUX_PIN_NUM_CLK, .quadhd_io_num = -1, .quadwp_io_num = -1,
.max_transfer_sz = 8, .flags = flags_expected};
TEST_ASSERT_EQUAL(ESP_ERR_INVALID_ARG, spicommon_bus_initialize_io(HSPI_HOST, &cfg, 0, flags_expected|SPICOMMON_BUSFLAG_MASTER, &flags_o));
TEST_ASSERT_EQUAL(ESP_ERR_INVALID_ARG, spicommon_bus_initialize_io(HSPI_HOST, &cfg, 0, flags_expected|SPICOMMON_BUSFLAG_SLAVE, &flags_o));
cfg = (spi_bus_config_t){.mosi_io_num = 34, .miso_io_num = HSPI_IOMUX_PIN_NUM_MISO, .sclk_io_num = HSPI_IOMUX_PIN_NUM_CLK, .quadhd_io_num = -1, .quadwp_io_num = -1,
.max_transfer_sz = 8, .flags = flags_expected};
TEST_ASSERT_EQUAL(ESP_ERR_INVALID_ARG, spicommon_bus_initialize_io(HSPI_HOST, &cfg, 0, flags_expected|SPICOMMON_BUSFLAG_MASTER, &flags_o));
TEST_ASSERT_EQUAL(ESP_ERR_INVALID_ARG, spicommon_bus_initialize_io(HSPI_HOST, &cfg, 0, flags_expected|SPICOMMON_BUSFLAG_SLAVE, &flags_o));
ESP_LOGI(TAG, "check sclk flag...");
flags_expected = SPICOMMON_BUSFLAG_SCLK;
cfg = (spi_bus_config_t){.mosi_io_num = HSPI_IOMUX_PIN_NUM_MOSI, .miso_io_num = HSPI_IOMUX_PIN_NUM_MISO, .sclk_io_num = -1, .quadhd_io_num = HSPI_IOMUX_PIN_NUM_HD, .quadwp_io_num = HSPI_IOMUX_PIN_NUM_WP,
.max_transfer_sz = 8, .flags = flags_expected};
TEST_ASSERT_EQUAL(ESP_ERR_INVALID_ARG, spicommon_bus_initialize_io(HSPI_HOST, &cfg, 0, flags_expected|SPICOMMON_BUSFLAG_MASTER, &flags_o));
TEST_ASSERT_EQUAL(ESP_ERR_INVALID_ARG, spicommon_bus_initialize_io(HSPI_HOST, &cfg, 0, flags_expected|SPICOMMON_BUSFLAG_SLAVE, &flags_o));
ESP_LOGI(TAG, "check mosi flag...");
flags_expected = SPICOMMON_BUSFLAG_MOSI;
cfg = (spi_bus_config_t){.mosi_io_num = -1, .miso_io_num = HSPI_IOMUX_PIN_NUM_MISO, .sclk_io_num = HSPI_IOMUX_PIN_NUM_CLK, .quadhd_io_num = HSPI_IOMUX_PIN_NUM_HD, .quadwp_io_num = HSPI_IOMUX_PIN_NUM_WP,
.max_transfer_sz = 8, .flags = flags_expected};
TEST_ASSERT_EQUAL(ESP_ERR_INVALID_ARG, spicommon_bus_initialize_io(HSPI_HOST, &cfg, 0, flags_expected|SPICOMMON_BUSFLAG_MASTER, &flags_o));
TEST_ASSERT_EQUAL(ESP_ERR_INVALID_ARG, spicommon_bus_initialize_io(HSPI_HOST, &cfg, 0, flags_expected|SPICOMMON_BUSFLAG_SLAVE, &flags_o));
ESP_LOGI(TAG, "check miso flag...");
flags_expected = SPICOMMON_BUSFLAG_MISO;
cfg = (spi_bus_config_t){.mosi_io_num = HSPI_IOMUX_PIN_NUM_MOSI, .miso_io_num = -1, .sclk_io_num = HSPI_IOMUX_PIN_NUM_CLK, .quadhd_io_num = HSPI_IOMUX_PIN_NUM_HD, .quadwp_io_num = HSPI_IOMUX_PIN_NUM_WP,
.max_transfer_sz = 8, .flags = flags_expected};
TEST_ASSERT_EQUAL(ESP_ERR_INVALID_ARG, spicommon_bus_initialize_io(HSPI_HOST, &cfg, 0, flags_expected|SPICOMMON_BUSFLAG_MASTER, &flags_o));
TEST_ASSERT_EQUAL(ESP_ERR_INVALID_ARG, spicommon_bus_initialize_io(HSPI_HOST, &cfg, 0, flags_expected|SPICOMMON_BUSFLAG_SLAVE, &flags_o));
ESP_LOGI(TAG, "check quad flag...");
flags_expected = SPICOMMON_BUSFLAG_QUAD;
cfg = (spi_bus_config_t){.mosi_io_num = HSPI_IOMUX_PIN_NUM_MOSI, .miso_io_num = HSPI_IOMUX_PIN_NUM_MISO, .sclk_io_num = HSPI_IOMUX_PIN_NUM_CLK, .quadhd_io_num = -1, .quadwp_io_num = HSPI_IOMUX_PIN_NUM_WP,
.max_transfer_sz = 8, .flags = flags_expected};
TEST_ASSERT_EQUAL(ESP_ERR_INVALID_ARG, spicommon_bus_initialize_io(HSPI_HOST, &cfg, 0, flags_expected|SPICOMMON_BUSFLAG_MASTER, &flags_o));
TEST_ASSERT_EQUAL(ESP_ERR_INVALID_ARG, spicommon_bus_initialize_io(HSPI_HOST, &cfg, 0, flags_expected|SPICOMMON_BUSFLAG_SLAVE, &flags_o));
cfg = (spi_bus_config_t){.mosi_io_num = HSPI_IOMUX_PIN_NUM_MOSI, .miso_io_num = HSPI_IOMUX_PIN_NUM_MISO, .sclk_io_num = HSPI_IOMUX_PIN_NUM_CLK, .quadhd_io_num = HSPI_IOMUX_PIN_NUM_HD, .quadwp_io_num = -1,
.max_transfer_sz = 8, .flags = flags_expected};
TEST_ASSERT_EQUAL(ESP_ERR_INVALID_ARG, spicommon_bus_initialize_io(HSPI_HOST, &cfg, 0, flags_expected|SPICOMMON_BUSFLAG_MASTER, &flags_o));
TEST_ASSERT_EQUAL(ESP_ERR_INVALID_ARG, spicommon_bus_initialize_io(HSPI_HOST, &cfg, 0, flags_expected|SPICOMMON_BUSFLAG_SLAVE, &flags_o));
}
TEST_CASE("SPI Master no response when switch from host1 (HSPI) to host2 (VSPI)", "[spi]")
{
//spi config
spi_bus_config_t bus_config;
spi_device_interface_config_t device_config;
spi_device_handle_t spi;
spi_host_device_t host;
int dma = 1;
memset(&bus_config, 0, sizeof(spi_bus_config_t));
memset(&device_config, 0, sizeof(spi_device_interface_config_t));
bus_config.miso_io_num = -1;
bus_config.mosi_io_num = 26;
bus_config.sclk_io_num = 25;
bus_config.quadwp_io_num = -1;
bus_config.quadhd_io_num = -1;
device_config.clock_speed_hz = 50000;
device_config.mode = 0;
device_config.spics_io_num = -1;
device_config.queue_size = 1;
device_config.flags = SPI_DEVICE_TXBIT_LSBFIRST | SPI_DEVICE_RXBIT_LSBFIRST;
struct spi_transaction_t transaction = {
.flags = SPI_TRANS_USE_TXDATA | SPI_TRANS_USE_RXDATA,
.length = 16,
.rx_buffer = NULL,
.tx_data = {0x04, 0x00}
};
//initialize for first host
host = 1;
TEST_ASSERT(spi_bus_initialize(host, &bus_config, dma) == ESP_OK);
TEST_ASSERT(spi_bus_add_device(host, &device_config, &spi) == ESP_OK);
printf("before first xmit\n");
TEST_ASSERT(spi_device_transmit(spi, &transaction) == ESP_OK);
printf("after first xmit\n");
TEST_ASSERT(spi_bus_remove_device(spi) == ESP_OK);
TEST_ASSERT(spi_bus_free(host) == ESP_OK);
//for second host and failed before
host = 2;
TEST_ASSERT(spi_bus_initialize(host, &bus_config, dma) == ESP_OK);
TEST_ASSERT(spi_bus_add_device(host, &device_config, &spi) == ESP_OK);
printf("before second xmit\n");
// the original version (bit mis-written) stucks here.
TEST_ASSERT(spi_device_transmit(spi, &transaction) == ESP_OK);
// test case success when see this.
printf("after second xmit\n");
TEST_ASSERT(spi_bus_remove_device(spi) == ESP_OK);
TEST_ASSERT(spi_bus_free(host) == ESP_OK);
}
IRAM_ATTR static uint32_t data_iram[320];
DRAM_ATTR static uint32_t data_dram[320]={0};
//force to place in code area.
static const uint32_t data_drom[320] = {0};
#if 1 //HSPI
#define PIN_NUM_MISO HSPI_IOMUX_PIN_NUM_MISO
#define PIN_NUM_MOSI HSPI_IOMUX_PIN_NUM_MOSI
#define PIN_NUM_CLK HSPI_IOMUX_PIN_NUM_CLK
#define PIN_NUM_CS HSPI_IOMUX_PIN_NUM_CS
#elif 1 //VSPI
#define PIN_NUM_MISO VSPI_IOMUX_PIN_NUM_MISO
#define PIN_NUM_MOSI VSPI_IOMUX_PIN_NUM_MOSI
#define PIN_NUM_CLK VSPI_IOMUX_PIN_NUM_CLK
#define PIN_NUM_CS VSPI_IOMUX_PIN_NUM_CS
#endif
#define PIN_NUM_DC 21
#define PIN_NUM_RST 18
#define PIN_NUM_BCKL 5
TEST_CASE("SPI Master DMA test, TX and RX in different regions", "[spi]")
{
uint32_t data_rxdram[320];
esp_err_t ret;
spi_device_handle_t spi;
spi_bus_config_t buscfg={
.miso_io_num=PIN_NUM_MISO,
.mosi_io_num=PIN_NUM_MOSI,
.sclk_io_num=PIN_NUM_CLK,
.quadwp_io_num=-1,
.quadhd_io_num=-1
};
spi_device_interface_config_t devcfg={
.clock_speed_hz=10000000, //Clock out at 10 MHz
.mode=0, //SPI mode 0
.spics_io_num=PIN_NUM_CS, //CS pin
.queue_size=7, //We want to be able to queue 7 transactions at a time
.pre_cb=NULL, //Specify pre-transfer callback to handle D/C line
};
//Initialize the SPI bus
ret=spi_bus_initialize(HSPI_HOST, &buscfg, 1);
TEST_ASSERT(ret==ESP_OK);
//Attach the LCD to the SPI bus
ret=spi_bus_add_device(HSPI_HOST, &devcfg, &spi);
TEST_ASSERT(ret==ESP_OK);
static spi_transaction_t trans[6];
int x;
printf("iram: %p, dram: %p, drom: %p\n", data_iram, data_dram, data_drom);
memset(trans, 0, 6*sizeof(spi_transaction_t));
trans[0].length = 320*8,
trans[0].tx_buffer = data_iram;
trans[0].rx_buffer = data_rxdram;
trans[1].length = 320*8,
trans[1].tx_buffer = data_dram;
trans[1].rx_buffer = data_rxdram;
trans[2].length = 320*8,
trans[2].tx_buffer = data_drom;
trans[2].rx_buffer = data_rxdram;
trans[3].length = 320*8,
trans[3].tx_buffer = data_drom;
trans[3].rx_buffer = data_iram;
trans[4].length = 320*8,
trans[4].rxlength = 8*4;
trans[4].tx_buffer = data_drom;
trans[4].flags = SPI_TRANS_USE_RXDATA;
trans[5].length = 8*4;
trans[5].flags = SPI_TRANS_USE_RXDATA | SPI_TRANS_USE_TXDATA;
//Queue all transactions.
for (x=0; x<6; x++) {
ret=spi_device_queue_trans(spi,&trans[x], portMAX_DELAY);
TEST_ASSERT(ret==ESP_OK);
}
for (x=0; x<6; x++) {
spi_transaction_t* ptr;
ret=spi_device_get_trans_result(spi,&ptr, portMAX_DELAY);
TEST_ASSERT(ret==ESP_OK);
TEST_ASSERT(ptr = trans+x);
}
TEST_ASSERT(spi_bus_remove_device(spi) == ESP_OK);
TEST_ASSERT(spi_bus_free(HSPI_HOST) == ESP_OK);
}
//this part tests 3 DMA issues in master mode, full-duplex in IDF2.1
// 1. RX buffer not aligned (start and end)
// 2. not setting rx_buffer
// 3. setting rx_length != length
TEST_CASE("SPI Master DMA test: length, start, not aligned", "[spi]")
{
uint8_t tx_buf[320]={0x12, 0x34, 0x56, 0x78, 0x9a, 0xbc, 0xde, 0xf0, 0xaa, 0xcc, 0xff, 0xee, 0x55, 0x77, 0x88, 0x43};
uint8_t rx_buf[320];
esp_err_t ret;
spi_device_handle_t spi;
spi_bus_config_t buscfg={
.miso_io_num=PIN_NUM_MOSI,
.mosi_io_num=PIN_NUM_MOSI,
.sclk_io_num=PIN_NUM_CLK,
.quadwp_io_num=-1,
.quadhd_io_num=-1
};
spi_device_interface_config_t devcfg={
.clock_speed_hz=10*1000*1000, //Clock out at 10 MHz
.mode=0, //SPI mode 0
.spics_io_num=PIN_NUM_CS, //CS pin
.queue_size=7, //We want to be able to queue 7 transactions at a time
.pre_cb=NULL,
};
//Initialize the SPI bus
ret=spi_bus_initialize(HSPI_HOST, &buscfg, 1);
TEST_ASSERT(ret==ESP_OK);
//Attach the LCD to the SPI bus
ret=spi_bus_add_device(HSPI_HOST, &devcfg, &spi);
TEST_ASSERT(ret==ESP_OK);
//connect MOSI to two devices breaks the output, fix it.
gpio_output_sel(buscfg.mosi_io_num, FUNC_GPIO, HSPID_OUT_IDX);
memset(rx_buf, 0x66, 320);
for ( int i = 0; i < 8; i ++ ) {
memset( rx_buf, 0x66, sizeof(rx_buf));
spi_transaction_t t = {};
t.length = 8*(i+1);
t.rxlength = 0;
t.tx_buffer = tx_buf+2*i;
t.rx_buffer = rx_buf + i;
if ( i == 1 ) {
//test set no start
t.rx_buffer = NULL;
} else if ( i == 2 ) {
//test rx length != tx_length
t.rxlength = t.length - 8;
}
spi_device_transmit( spi, &t );
for( int i = 0; i < 16; i ++ ) {
printf("%02X ", rx_buf[i]);
}
printf("\n");
if ( i == 1 ) {
// no rx, skip check
} else if ( i == 2 ) {
//test rx length = tx length-1
TEST_ASSERT_EQUAL_HEX8_ARRAY(t.tx_buffer, t.rx_buffer, t.length/8-1 );
} else {
//normal check
TEST_ASSERT_EQUAL_HEX8_ARRAY(t.tx_buffer, t.rx_buffer, t.length/8 );
}
}
TEST_ASSERT(spi_bus_remove_device(spi) == ESP_OK);
TEST_ASSERT(spi_bus_free(HSPI_HOST) == ESP_OK);
}
static const char MASTER_TAG[] = "test_master";
static const char SLAVE_TAG[] = "test_slave";
DRAM_ATTR static uint8_t master_send[] = {0x93, 0x34, 0x56, 0x78, 0x9a, 0xbc, 0xde, 0xf0, 0xaa, 0xcc, 0xff, 0xee, 0x55, 0x77, 0x88, 0x43};
DRAM_ATTR static uint8_t slave_send[] = { 0xaa, 0xdc, 0xba, 0x98, 0x76, 0x54, 0x32, 0x10, 0x13, 0x57, 0x9b, 0xdf, 0x24, 0x68, 0xac, 0xe0 };
static void master_deinit(spi_device_handle_t spi)
{
TEST_ESP_OK( spi_bus_remove_device(spi) );
TEST_ESP_OK( spi_bus_free(HSPI_HOST) );
}
static void slave_pull_up(const spi_bus_config_t* cfg, int spics_io_num)
{
gpio_set_pull_mode(cfg->mosi_io_num, GPIO_PULLUP_ENABLE);
gpio_set_pull_mode(cfg->sclk_io_num, GPIO_PULLUP_ENABLE);
gpio_set_pull_mode(spics_io_num, GPIO_PULLUP_ENABLE);
}
typedef struct {
uint32_t len;
uint8_t *start;
} slave_txdata_t;
typedef struct {
uint32_t len;
uint8_t* tx_start;
uint8_t data[1];
} slave_rxdata_t;
typedef struct {
spi_host_device_t spi;
RingbufHandle_t data_received;
QueueHandle_t data_to_send;
} spi_slave_task_context_t;
esp_err_t init_slave_context(spi_slave_task_context_t *context)
{
context->data_to_send = xQueueCreate( 16, sizeof( slave_txdata_t ));
if ( context->data_to_send == NULL ) {
return ESP_ERR_NO_MEM;
}
context->data_received = xRingbufferCreate( 1024, RINGBUF_TYPE_NOSPLIT );
if ( context->data_received == NULL ) {
return ESP_ERR_NO_MEM;
}
context->spi=VSPI_HOST;
return ESP_OK;
}
void deinit_slave_context(spi_slave_task_context_t *context)
{
TEST_ASSERT( context->data_to_send != NULL );
vQueueDelete( context->data_to_send );
context->data_to_send = NULL;
TEST_ASSERT( context->data_received != NULL );
vRingbufferDelete( context->data_received );
context->data_received = NULL;
}
/* The task requires a queue and a ringbuf, which should be initialized before task starts.
Send ``slave_txdata_t`` to the queue to make the task send data;
the task returns data got to the ringbuf, which should have sufficient size.
*/
static void task_slave(void* arg)
{
spi_slave_task_context_t* context = (spi_slave_task_context_t*) arg;
QueueHandle_t queue = context->data_to_send;
RingbufHandle_t ringbuf = context->data_received;
uint8_t recvbuf[320+8];
slave_txdata_t txdata;
ESP_LOGI( SLAVE_TAG, "slave up" );
//never quit, but blocked by the queue, waiting to be killed, when no more send from main task.
while( 1 ) {
xQueueReceive( queue, &txdata, portMAX_DELAY );
ESP_LOGI( "test", "to send: %p", txdata.start );
spi_slave_transaction_t t = {};
t.length = txdata.len;
t.tx_buffer = txdata.start;
t.rx_buffer = recvbuf+8;
//loop until trans_len != 0 to skip glitches
memset(recvbuf, 0x66, sizeof(recvbuf));
do {
TEST_ESP_OK( spi_slave_transmit( context->spi, &t, portMAX_DELAY ) );
} while ( t.trans_len == 0 );
memcpy(recvbuf, &t.trans_len, sizeof(uint32_t));
*(uint8_t**)(recvbuf+4) = txdata.start;
ESP_LOGI( SLAVE_TAG, "received: %d", t.trans_len );
xRingbufferSend( ringbuf, recvbuf, 8+(t.trans_len+7)/8, portMAX_DELAY );
}
}
#define TEST_SPI_HOST HSPI_HOST
#define TEST_SLAVE_HOST VSPI_HOST
static uint8_t bitswap(uint8_t in)
{
uint8_t out = 0;
for (int i = 0; i < 8; i++) {
out = out >> 1;
if (in&0x80) out |= 0x80;
in = in << 1;
}
return out;
}
void test_cmd_addr(spi_slave_task_context_t *slave_context, bool lsb_first)
{
spi_device_handle_t spi;
ESP_LOGI(MASTER_TAG, ">>>>>>>>> TEST %s FIRST <<<<<<<<<<<", lsb_first?"LSB":"MSB");
//initial master, mode 0, 1MHz
spi_bus_config_t buscfg=SPI_BUS_TEST_DEFAULT_CONFIG();
TEST_ESP_OK(spi_bus_initialize(TEST_SPI_HOST, &buscfg, 1));
spi_device_interface_config_t devcfg=SPI_DEVICE_TEST_DEFAULT_CONFIG();
devcfg.clock_speed_hz = 1*1000*1000;
if (lsb_first) devcfg.flags |= SPI_DEVICE_BIT_LSBFIRST;
TEST_ESP_OK(spi_bus_add_device(TEST_SPI_HOST, &devcfg, &spi));
//connecting pins to two peripherals breaks the output, fix it.
gpio_output_sel(buscfg.mosi_io_num, FUNC_GPIO, spi_periph_signal[TEST_SPI_HOST].spid_out);
gpio_output_sel(buscfg.miso_io_num, FUNC_GPIO, spi_periph_signal[TEST_SLAVE_HOST].spiq_out);
gpio_output_sel(devcfg.spics_io_num, FUNC_GPIO, spi_periph_signal[TEST_SPI_HOST].spics_out[0]);
gpio_output_sel(buscfg.sclk_io_num, FUNC_GPIO, spi_periph_signal[TEST_SPI_HOST].spiclk_out);
for (int i= 0; i < 8; i++) {
//prepare slave tx data
slave_txdata_t slave_txdata = (slave_txdata_t) {
.start = slave_send,
.len = 256,
};
xQueueSend(slave_context->data_to_send, &slave_txdata, portMAX_DELAY);
vTaskDelay(50);
//prepare master tx data
int cmd_bits = (i+1)*2;
int addr_bits = 56-8*i;
int round_up = (cmd_bits+addr_bits+7)/8*8;
addr_bits = round_up - cmd_bits;
spi_transaction_ext_t trans = (spi_transaction_ext_t) {
.base = {
.flags = SPI_TRANS_VARIABLE_CMD | SPI_TRANS_VARIABLE_ADDR,
.addr = 0x456789abcdef0123,
.cmd = 0xcdef,
},
.command_bits = cmd_bits,
.address_bits = addr_bits,
};
ESP_LOGI( MASTER_TAG, "===== test%d =====", i );
ESP_LOGI(MASTER_TAG, "cmd_bits %d, addr_bits: %d", cmd_bits, addr_bits);
TEST_ESP_OK(spi_device_transmit(spi, (spi_transaction_t*)&trans));
//wait for both master and slave end
size_t rcv_len;
slave_rxdata_t *rcv_data = xRingbufferReceive(slave_context->data_received, &rcv_len, portMAX_DELAY);
rcv_len-=8;
uint8_t *buffer = rcv_data->data;
ESP_LOGI(SLAVE_TAG, "trans_len: %d", rcv_len);
TEST_ASSERT_EQUAL(rcv_len, (rcv_data->len+7)/8);
TEST_ASSERT_EQUAL(rcv_data->len, cmd_bits+addr_bits);
ESP_LOG_BUFFER_HEX("slave rx", buffer, rcv_len);
uint16_t cmd_expected = trans.base.cmd & (BIT(cmd_bits) - 1);
uint64_t addr_expected = trans.base.addr & ((1ULL<<addr_bits) - 1);
uint8_t *data_ptr = buffer;
uint16_t cmd_got = *(uint16_t*)data_ptr;
data_ptr += cmd_bits/8;
cmd_got = __builtin_bswap16(cmd_got);
cmd_got = cmd_got >> (16-cmd_bits);
int remain_bits = cmd_bits % 8;
uint64_t addr_got = *(uint64_t*)data_ptr;
data_ptr += 8;
addr_got = __builtin_bswap64(addr_got);
addr_got = (addr_got << remain_bits);
addr_got |= (*data_ptr >> (8-remain_bits));
addr_got = addr_got >> (64-addr_bits);
if (lsb_first) {
cmd_got = __builtin_bswap16(cmd_got);
addr_got = __builtin_bswap64(addr_got);
uint8_t *swap_ptr = (uint8_t*)&cmd_got;
swap_ptr[0] = bitswap(swap_ptr[0]);
swap_ptr[1] = bitswap(swap_ptr[1]);
cmd_got = cmd_got >> (16-cmd_bits);
swap_ptr = (uint8_t*)&addr_got;
for (int j = 0; j < 8; j++) swap_ptr[j] = bitswap(swap_ptr[j]);
addr_got = addr_got >> (64-addr_bits);
}
ESP_LOGI(SLAVE_TAG, "cmd_got: %04X, addr_got: %08X%08X", cmd_got, (uint32_t)(addr_got>>32), (uint32_t)addr_got);
TEST_ASSERT_EQUAL_HEX16(cmd_expected, cmd_got);
if (addr_bits > 0) {
TEST_ASSERT_EQUAL_HEX32(addr_expected, addr_got);
TEST_ASSERT_EQUAL_HEX32(addr_expected >> 8, addr_got >> 8);
}
//clean
vRingbufferReturnItem(slave_context->data_received, buffer);
}
TEST_ASSERT(spi_bus_remove_device(spi) == ESP_OK);
TEST_ASSERT(spi_bus_free(TEST_SPI_HOST) == ESP_OK);
}
TEST_CASE("SPI master variable cmd & addr test","[spi]")
{
spi_slave_task_context_t slave_context = {};
esp_err_t err = init_slave_context( &slave_context );
TEST_ASSERT( err == ESP_OK );
TaskHandle_t handle_slave;
xTaskCreate( task_slave, "spi_slave", 4096, &slave_context, 0, &handle_slave);
//initial slave, mode 0, no dma
int dma_chan = 0;
int slave_mode = 0;
spi_bus_config_t slv_buscfg=SPI_BUS_TEST_DEFAULT_CONFIG();
spi_slave_interface_config_t slvcfg=SPI_SLAVE_TEST_DEFAULT_CONFIG();
slvcfg.mode = slave_mode;
//Initialize SPI slave interface
TEST_ESP_OK( spi_slave_initialize(TEST_SLAVE_HOST, &slv_buscfg, &slvcfg, dma_chan) );
test_cmd_addr(&slave_context, false);
test_cmd_addr(&slave_context, true);
vTaskDelete( handle_slave );
handle_slave = 0;
deinit_slave_context(&slave_context);
TEST_ASSERT(spi_slave_free(TEST_SLAVE_HOST) == ESP_OK);
ESP_LOGI(MASTER_TAG, "test passed.");
}
2018-04-19 04:47:29 +00:00
/********************************************************************************
* Test Timing By Internal Connections
********************************************************************************/
typedef enum {
FULL_DUPLEX = 0,
HALF_DUPLEX_MISO = 1,
HALF_DUPLEX_MOSI = 2,
} spi_dup_t;
static int timing_speed_array[]={/**/
SPI_MASTER_FREQ_8M ,
SPI_MASTER_FREQ_9M ,
SPI_MASTER_FREQ_10M,
SPI_MASTER_FREQ_11M,
SPI_MASTER_FREQ_13M,
SPI_MASTER_FREQ_16M,
SPI_MASTER_FREQ_20M,
SPI_MASTER_FREQ_26M,
SPI_MASTER_FREQ_40M,
SPI_MASTER_FREQ_80M,
};
typedef struct {
uint8_t master_rxbuf[320];
spi_transaction_t master_trans[16];
TaskHandle_t handle_slave;
spi_slave_task_context_t slave_context;
slave_txdata_t slave_trans[16];
} timing_context_t;
void master_print_data(spi_transaction_t *t, spi_dup_t dup)
{
if (t->tx_buffer) {
ESP_LOG_BUFFER_HEX( "master tx", t->tx_buffer, t->length/8 );
} else {
ESP_LOGI( "master tx", "no data" );
}
int rxlength;
if (dup!=HALF_DUPLEX_MISO) {
rxlength = t->length/8;
} else {
rxlength = t->rxlength/8;
}
if (t->rx_buffer) {
ESP_LOG_BUFFER_HEX( "master rx", t->rx_buffer, rxlength );
} else {
ESP_LOGI( "master rx", "no data" );
}
}
void slave_print_data(slave_rxdata_t *t)
{
int rcv_len = (t->len+7)/8;
ESP_LOGI(SLAVE_TAG, "trans_len: %d", t->len);
ESP_LOG_BUFFER_HEX( "slave tx", t->tx_start, rcv_len);
ESP_LOG_BUFFER_HEX( "slave rx", t->data, rcv_len);
}
esp_err_t check_data(spi_transaction_t *t, spi_dup_t dup, slave_rxdata_t *slave_t)
{
int length;
if (dup!=HALF_DUPLEX_MISO) {
length = t->length;
} else {
length = t->rxlength;
}
TEST_ASSERT(length!=0);
//currently the rcv_len can be in range of [t->length-1, t->length+3]
uint32_t rcv_len = slave_t->len;
TEST_ASSERT(rcv_len >= length-1 && rcv_len <= length+3);
//the timing speed is temporarily only for master
if (dup!=HALF_DUPLEX_MISO) {
// TEST_ASSERT_EQUAL_HEX8_ARRAY(t->tx_buffer, slave_t->data, (t->length+7)/8);
}
if (dup!=HALF_DUPLEX_MOSI) {
TEST_ASSERT_EQUAL_HEX8_ARRAY(slave_t->tx_start, t->rx_buffer, (length+7)/8);
}
return ESP_OK;
}
static void timing_init_transactions(spi_dup_t dup, timing_context_t* context)
{
spi_transaction_t* trans = context->master_trans;
uint8_t *rx_buf_ptr = context->master_rxbuf;
if (dup==HALF_DUPLEX_MISO) {
for (int i = 0; i < 8; i++ ) {
trans[i] = (spi_transaction_t) {
.flags = 0,
.rxlength = 8*(i*2+1),
.rx_buffer = rx_buf_ptr,
};
rx_buf_ptr += ((context->master_trans[i].rxlength + 31)/8)&(~3);
}
} else if (dup==HALF_DUPLEX_MOSI) {
for (int i = 0; i < 8; i++ ) {
trans[i] = (spi_transaction_t) {
.flags = 0,
.length = 8*(i*2+1),
.tx_buffer = master_send+i,
};
}
} else {
for (int i = 0; i < 8; i++ ) {
trans[i] = (spi_transaction_t) {
.flags = 0,
.length = 8*(i*2+1),
.tx_buffer = master_send+i,
.rx_buffer = rx_buf_ptr,
};
rx_buf_ptr += ((context->master_trans[i].length + 31)/8)&(~3);
}
}
//prepare slave tx data
for (int i = 0; i < 8; i ++) {
context->slave_trans[i] = (slave_txdata_t) {
.start = slave_send + 4*(i%3),
.len = 256,
};
}
}
typedef struct {
const char cfg_name[30];
/*The test work till the frequency below,
*set the frequency to higher and remove checks in the driver to know how fast the system can run.
*/
int freq_limit;
spi_dup_t dup;
bool master_iomux;
bool slave_iomux;
2018-04-19 04:47:29 +00:00
int slave_tv_ns;
} test_timing_config_t;
#define ESP_SPI_SLAVE_TV (12.5*3)
#define GPIO_DELAY (12.5*2)
#define SAMPLE_DELAY 12.5
#define TV_INT_CONNECT_GPIO (ESP_SPI_SLAVE_TV+GPIO_DELAY)
#define TV_INT_CONNECT (ESP_SPI_SLAVE_TV)
#define TV_WITH_ESP_SLAVE_GPIO (ESP_SPI_SLAVE_TV+SAMPLE_DELAY+GPIO_DELAY)
#define TV_WITH_ESP_SLAVE (ESP_SPI_SLAVE_TV+SAMPLE_DELAY)
//currently ESP32 slave only supports up to 20MHz, but 40MHz on the same board
#define ESP_SPI_SLAVE_MAX_FREQ SPI_MASTER_FREQ_20M
#define ESP_SPI_SLAVE_MAX_FREQ_SYNC SPI_MASTER_FREQ_40M
static test_timing_config_t timing_master_conf_t[] = {/**/
{ .cfg_name = "FULL_DUP, MASTER IOMUX",
2018-04-19 04:47:29 +00:00
.freq_limit = SPI_MASTER_FREQ_13M,
.dup = FULL_DUPLEX,
.master_iomux = true,
.slave_iomux = false,
2018-04-19 04:47:29 +00:00
.slave_tv_ns = TV_INT_CONNECT_GPIO,
},
{ .cfg_name = "FULL_DUP, SLAVE IOMUX",
2018-04-19 04:47:29 +00:00
.freq_limit = SPI_MASTER_FREQ_13M,
.dup = FULL_DUPLEX,
.master_iomux = false,
.slave_iomux = true,
2018-04-19 04:47:29 +00:00
.slave_tv_ns = TV_INT_CONNECT,
},
{ .cfg_name = "FULL_DUP, BOTH GPIO",
.freq_limit = SPI_MASTER_FREQ_10M,
.dup = FULL_DUPLEX,
.master_iomux = false,
.slave_iomux = false,
2018-04-19 04:47:29 +00:00
.slave_tv_ns = TV_INT_CONNECT_GPIO,
},
{ .cfg_name = "HALF_DUP, MASTER IOMUX",
2018-04-19 04:47:29 +00:00
.freq_limit = ESP_SPI_SLAVE_MAX_FREQ_SYNC,
.dup = HALF_DUPLEX_MISO,
.master_iomux = true,
.slave_iomux = false,
2018-04-19 04:47:29 +00:00
.slave_tv_ns = TV_INT_CONNECT_GPIO,
},
{ .cfg_name = "HALF_DUP, SLAVE IOMUX",
2018-04-19 04:47:29 +00:00
.freq_limit = ESP_SPI_SLAVE_MAX_FREQ_SYNC,
.dup = HALF_DUPLEX_MISO,
.master_iomux = false,
.slave_iomux = true,
2018-04-19 04:47:29 +00:00
.slave_tv_ns = TV_INT_CONNECT,
},
{ .cfg_name = "HALF_DUP, BOTH GPIO",
.freq_limit = ESP_SPI_SLAVE_MAX_FREQ_SYNC,
.dup = HALF_DUPLEX_MISO,
.master_iomux = false,
.slave_iomux = false,
2018-04-19 04:47:29 +00:00
.slave_tv_ns = TV_INT_CONNECT_GPIO,
},
{ .cfg_name = "MOSI_DUP, MASTER IOMUX",
2018-04-19 04:47:29 +00:00
.freq_limit = ESP_SPI_SLAVE_MAX_FREQ_SYNC,
.dup = HALF_DUPLEX_MOSI,
.master_iomux = true,
.slave_iomux = false,
2018-04-19 04:47:29 +00:00
.slave_tv_ns = TV_INT_CONNECT_GPIO,
},
{ .cfg_name = "MOSI_DUP, SLAVE IOMUX",
2018-04-19 04:47:29 +00:00
.freq_limit = ESP_SPI_SLAVE_MAX_FREQ_SYNC,
.dup = HALF_DUPLEX_MOSI,
.master_iomux = false,
.slave_iomux = true,
2018-04-19 04:47:29 +00:00
.slave_tv_ns = TV_INT_CONNECT,
},
{ .cfg_name = "MOSI_DUP, BOTH GPIO",
.freq_limit = ESP_SPI_SLAVE_MAX_FREQ_SYNC,
.dup = HALF_DUPLEX_MOSI,
.master_iomux = false,
.slave_iomux = false,
2018-04-19 04:47:29 +00:00
.slave_tv_ns = TV_INT_CONNECT_GPIO,
},
};
//this case currently only checks master read
TEST_CASE("test timing_master","[spi][timeout=120]")
{
timing_context_t context;
//Enable pull-ups on SPI lines so we don't detect rogue pulses when no master is connected.
//slave_pull_up(&slv_buscfg, slvcfg.spics_io_num);
context.slave_context = (spi_slave_task_context_t){};
esp_err_t err = init_slave_context( &context.slave_context );
TEST_ASSERT( err == ESP_OK );
xTaskCreate( task_slave, "spi_slave", 4096, &context.slave_context, 0, &context.handle_slave);
const int test_size = sizeof(timing_master_conf_t)/sizeof(test_timing_config_t);
for (int i = 0; i < test_size; i++) {
test_timing_config_t* conf = &timing_master_conf_t[i];
spi_device_handle_t spi;
timing_init_transactions(conf->dup, &context);
ESP_LOGI(MASTER_TAG, "****************** %s ***************", conf->cfg_name);
for (int j=0; j<sizeof(timing_speed_array)/sizeof(int); j++ ) {
if (timing_speed_array[j] > conf->freq_limit) break;
ESP_LOGI(MASTER_TAG, "======> %dk", timing_speed_array[j]/1000);
//master config
const int master_mode = 0;
spi_bus_config_t buscfg=SPI_BUS_TEST_DEFAULT_CONFIG();
spi_device_interface_config_t devcfg=SPI_DEVICE_TEST_DEFAULT_CONFIG();
devcfg.mode = master_mode;
if (conf->dup==HALF_DUPLEX_MISO||conf->dup==HALF_DUPLEX_MOSI) {
devcfg.cs_ena_pretrans = 20;
devcfg.flags |= SPI_DEVICE_HALFDUPLEX;
} else {
devcfg.cs_ena_pretrans = 1;
}
devcfg.cs_ena_posttrans = 20;
devcfg.input_delay_ns = conf->slave_tv_ns;
devcfg.clock_speed_hz = timing_speed_array[j];
//slave config
int slave_mode = 0;
spi_slave_interface_config_t slvcfg=SPI_SLAVE_TEST_DEFAULT_CONFIG();
slvcfg.mode = slave_mode;
//pin config & initialize
//we can't have two sets of iomux pins on the same pins
assert(!conf->master_iomux || !conf->slave_iomux);
if (conf->slave_iomux) {
//only in this case, use VSPI iomux pins
buscfg.miso_io_num = VSPI_IOMUX_PIN_NUM_MISO;
buscfg.mosi_io_num = VSPI_IOMUX_PIN_NUM_MOSI;
buscfg.sclk_io_num = VSPI_IOMUX_PIN_NUM_CLK;
devcfg.spics_io_num = VSPI_IOMUX_PIN_NUM_CS;
slvcfg.spics_io_num = VSPI_IOMUX_PIN_NUM_CS;
2018-04-19 04:47:29 +00:00
} else {
buscfg.miso_io_num = HSPI_IOMUX_PIN_NUM_MISO;
buscfg.mosi_io_num = HSPI_IOMUX_PIN_NUM_MOSI;
buscfg.sclk_io_num = HSPI_IOMUX_PIN_NUM_CLK;
devcfg.spics_io_num = HSPI_IOMUX_PIN_NUM_CS;
slvcfg.spics_io_num = HSPI_IOMUX_PIN_NUM_CS;
2018-04-19 04:47:29 +00:00
}
slave_pull_up(&buscfg, slvcfg.spics_io_num);
//this does nothing, but avoid the driver from using iomux pins if required
buscfg.quadhd_io_num = (!conf->master_iomux && !conf->slave_iomux? VSPI_IOMUX_PIN_NUM_MISO: -1);
2018-04-19 04:47:29 +00:00
TEST_ESP_OK(spi_bus_initialize(HSPI_HOST, &buscfg, 0));
TEST_ESP_OK(spi_bus_add_device(HSPI_HOST, &devcfg, &spi));
//slave automatically use iomux pins if pins are on VSPI_* pins
2018-04-19 04:47:29 +00:00
buscfg.quadhd_io_num = -1;
TEST_ESP_OK( spi_slave_initialize(VSPI_HOST, &buscfg, &slvcfg, 0) );
//initialize master and slave on the same pins break some of the output configs, fix them
if (conf->master_iomux) {
2018-04-19 04:47:29 +00:00
gpio_output_sel(buscfg.mosi_io_num, FUNC_SPI, HSPID_OUT_IDX);
gpio_output_sel(buscfg.miso_io_num, FUNC_GPIO, VSPIQ_OUT_IDX);
gpio_output_sel(devcfg.spics_io_num, FUNC_SPI, HSPICS0_OUT_IDX);
gpio_output_sel(buscfg.sclk_io_num, FUNC_SPI, HSPICLK_OUT_IDX);
} else if (conf->slave_iomux) {
2018-04-19 04:47:29 +00:00
gpio_output_sel(buscfg.mosi_io_num, FUNC_GPIO, HSPID_OUT_IDX);
gpio_output_sel(buscfg.miso_io_num, FUNC_SPI, VSPIQ_OUT_IDX);
gpio_output_sel(devcfg.spics_io_num, FUNC_GPIO, HSPICS0_OUT_IDX);
gpio_output_sel(buscfg.sclk_io_num, FUNC_GPIO, HSPICLK_OUT_IDX);
} else {
gpio_output_sel(buscfg.mosi_io_num, FUNC_GPIO, HSPID_OUT_IDX);
gpio_output_sel(buscfg.miso_io_num, FUNC_GPIO, VSPIQ_OUT_IDX);
gpio_output_sel(devcfg.spics_io_num, FUNC_GPIO, HSPICS0_OUT_IDX);
gpio_output_sel(buscfg.sclk_io_num, FUNC_GPIO, HSPICLK_OUT_IDX);
}
//clear master receive buffer
memset(context.master_rxbuf, 0x66, sizeof(context.master_rxbuf));
//prepare slave tx data
for (int k = 0; k < 8; k ++) xQueueSend( context.slave_context.data_to_send, &context.slave_trans[k], portMAX_DELAY );
for( int k= 0; k < 8; k ++ ) {
//wait for both master and slave end
ESP_LOGI( MASTER_TAG, "=> test%d", k );
//send master tx data
vTaskDelay(9);
spi_transaction_t *t = &context.master_trans[k];
TEST_ESP_OK (spi_device_transmit( spi, t) );
master_print_data(t, conf->dup);
size_t rcv_len;
slave_rxdata_t *rcv_data = xRingbufferReceive( context.slave_context.data_received, &rcv_len, portMAX_DELAY );
slave_print_data(rcv_data);
//check result
TEST_ESP_OK(check_data(t, conf->dup, rcv_data));
//clean
vRingbufferReturnItem(context.slave_context.data_received, rcv_data);
}
master_deinit(spi);
TEST_ASSERT(spi_slave_free(VSPI_HOST) == ESP_OK);
}
}
vTaskDelete( context.handle_slave );
context.handle_slave = 0;
deinit_slave_context(&context.slave_context);
ESP_LOGI(MASTER_TAG, "test passed.");
}
/********************************************************************************
* Test SPI transaction interval
********************************************************************************/
#define RECORD_TIME_PREPARE() uint32_t __t1, __t2
#define RECORD_TIME_START() do {__t1 = xthal_get_ccount();}while(0)
#define RECORD_TIME_END(p_time) do{__t2 = xthal_get_ccount(); *p_time = (__t2-__t1)/240;}while(0)
static void speed_setup(spi_device_handle_t* spi, bool use_dma)
{
esp_err_t ret;
spi_bus_config_t buscfg=SPI_BUS_TEST_DEFAULT_CONFIG();
spi_device_interface_config_t devcfg=SPI_DEVICE_TEST_DEFAULT_CONFIG();
devcfg.queue_size=8; //We want to be able to queue 7 transactions at a time
//Initialize the SPI bus and the device to test
ret=spi_bus_initialize(HSPI_HOST, &buscfg, (use_dma?1:0));
TEST_ASSERT(ret==ESP_OK);
ret=spi_bus_add_device(HSPI_HOST, &devcfg, spi);
TEST_ASSERT(ret==ESP_OK);
}
static void speed_deinit(spi_device_handle_t spi)
{
TEST_ESP_OK( spi_bus_remove_device(spi) );
TEST_ESP_OK( spi_bus_free(HSPI_HOST) );
}
static void sorted_array_insert(uint32_t* array, int* size, uint32_t item)
{
int pos;
for (pos = *size; pos>0; pos--) {
if (array[pos-1] < item) break;
array[pos] = array[pos-1];
}
array[pos]=item;
(*size)++;
}
#define TEST_TIMES 11
TEST_CASE("spi_speed","[spi]")
{
RECORD_TIME_PREPARE();
uint32_t t_flight;
//to get rid of the influence of randomly interrupts, we measured the performance by median value
uint32_t t_flight_sorted[TEST_TIMES];
int t_flight_num = 0;
spi_device_handle_t spi;
const bool use_dma = true;
WORD_ALIGNED_ATTR spi_transaction_t trans = {
.length = 1*8,
.flags = SPI_TRANS_USE_TXDATA,
};
//first work with DMA
speed_setup(&spi, use_dma);
//first time introduces a device switch, which costs more time. we skip this
spi_device_transmit(spi, &trans);
//record flight time by isr, with DMA
t_flight_num = 0;
for (int i = 0; i < TEST_TIMES; i++) {
spi_device_transmit(spi, &trans); // prime the flash cache
RECORD_TIME_START();
spi_device_transmit(spi, &trans);
RECORD_TIME_END(&t_flight);
sorted_array_insert(t_flight_sorted, &t_flight_num, t_flight);
}
TEST_PERFORMANCE_LESS_THAN(SPI_PER_TRANS_NO_POLLING, "%d us", t_flight_sorted[(TEST_TIMES+1)/2]);
for (int i = 0; i < TEST_TIMES; i++) {
ESP_LOGI(TAG, "%d", t_flight_sorted[i]);
}
speed_deinit(spi);
speed_setup(&spi, !use_dma);
//first time introduces a device switch, which costs more time. we skip this
spi_device_transmit(spi, &trans);
//record flight time by isr, without DMA
t_flight_num = 0;
for (int i = 0; i < TEST_TIMES; i++) {
RECORD_TIME_START();
spi_device_transmit(spi, &trans);
RECORD_TIME_END(&t_flight);
sorted_array_insert(t_flight_sorted, &t_flight_num, t_flight);
}
TEST_PERFORMANCE_LESS_THAN( SPI_PER_TRANS_NO_POLLING_NO_DMA, "%d us", t_flight_sorted[(TEST_TIMES+1)/2]);
for (int i = 0; i < TEST_TIMES; i++) {
ESP_LOGI(TAG, "%d", t_flight_sorted[i]);
}
speed_deinit(spi);
}